1
INSTRUCTION MANUAL
16" Variable Speed Scroll Saw
with Quickset II Blade
Changing Feature
(Model 40-570)
PART NO. 898602-0010
Copyright © 2000 Delta Machinery
ESPAÑOL: PÁGINA 15
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-888-848-5175 (In Canada call 1-800-463-3582).
®
2
SAFETY RULES
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain
hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the
possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may
result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can
reduce your potential for injury. But even the best guard won’t make up for poor judgment, carelessness or inattention. Always use
common sense and exercise caution in the workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative
procedure that feels safer. REMEMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. Delta strongly recommends that this machine not be modified and/or
used for any application other than that for which it was designed. If you have any questions relative to a particular application,
DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 Southgate Drive, Guelph, Ontario N1H 6M7)
WARNING: FAILURE TO FOLLOW THESE RULES
MAY RESULT IN SERIOUS PERSONAL INJURY
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL. Learn the
tool’s application and limitations as well as the specific
hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it “on.”
5. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose them to
rain. Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY. All children
and visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILDPROOF – with padlocks,
master switches, or by removing starter keys.
9. DON’T FORCE TOOL. It will do the job better and be
safer at the rate for which it was designed.
10. USE RIGHT TOOL. Don’t force tool or attachment to do a
job for which it was not designed.
11. WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught in
moving parts. Non-slip footwear is recommended. Wear
protective hair covering to contain long hair.
12. ALWAYS USE SAFETY GLASSES. Wear safety glasses.
Everyday eyeglasses only have impact resistant lenses; they
are not safety glasses. Also use face or dust mask if cutting
operation is dusty. These safety glasses must conform to ANSI
Z87.1 requirements. Note: Approved glasses have Z87 printed
or stamped on them.
13. SECURE WORK. Use clamps or a vise to hold work when
practical. It’s safer than using your hand and frees both hands
to operate tool.
14. DON’T OVERREACH. Keep proper footing and balance at
all times.
15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
16. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
17. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by Delta may
cause hazards or risk of injury to persons.
18. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in “OFF” position before plugging in
power cord.
19. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is accidentally
contacted.
20. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be carefully
checked to ensure that it will operate properly and
perform its intended function – check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired or
replaced.
21. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter only.
22.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF
. Don’t leave tool until it comes to a complete stop.
23. DRUGS, ALCOHOL, MEDICATION. Do not operate tool
while under the influence of drugs, alcohol or any
medication.
24. MAKE SURE TOOL IS DISCONNECTED FROM POWER
SUPPLY
while motor is being mounted, connected or
reconnected.
25. THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always operate
machinery in well ventilated areas and provide for proper dust
removal. Use wood dust collection systems whenever possible.
26. WHEN THE UNIT IS NOT IN USE the switch should be
locked in the “OFF” position to prevent unauthorized use.
27. SOME DUST CREATED BY POWER SANDING,
SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to
cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
SAVE THESE INSTRUCTIONS
3
ADDITIONAL SAFETY RULES
FOR SCROLL SAWS
1. DO NOT operate your scroll saw until it is
completely assembled and installed according to the
instructions.
2. IF YOU ARE NOT thoroughly familiar with the
operation of Scroll Saws, obtain advice from your
supervisor, instructor or other qualified person.
3. YOUR SCROLL SAW MUST be securely fastened
to a stand or workbench. If there is any tendency for the
stand or workbench to move during operation, the
stand or workbench MUST be fastened to the floor.
4. THIS SCROLL SAW is intended for indoor use only.
5. MAKE SURE blade is properly tensioned before
operating saw.
6. TO AVOID blade breakage ALWAYS adjust blade
tension correctly.
7. MAKE SURE the blade teeth point downward
toward the table.
8. NEVER turn the saw “ON” before clearing the table
of all objects (tools, scraps of wood, etc.).
9. DO NOT cut material that is too small to be safely
supported.
10. AVOID awkward hand positions where a sudden
slip could cause a hand to move into the blade.
11. ALWAYS keep hands and fingers away from blade.
12. ALWAYS adjust holddown foot for each new
operation.
13. DO NOT USE dull or bent blades.
14. DO NOT attempt to saw material that does not have
a flat surface, unless a suitable support is used.
15. MAKE “relief” cuts before cutting long curves.
16. NEVER attempt to cut a curve that is too tight for
the blade being used.
17. WHEN backing a blade out of a workpiece, the
blade may bind in the saw kerf. This is usually caused
by sawdust in the kerf. If this happens, turn “OFF” the
switch and remove plug from power source outlet.
Wedge open the kerf and back blade out of the
workpiece.
18. THE USE of attachments and accessories not
recommended by Delta may result in the risk of injuries.
19. ALWAYS hold the work firmly against the table.
20. DO NOT feed the material too fast while cutting.
Only feed the material fast enough so that the blade will
cut.
21. NEVER start the Scroll Saw with the stock pressed
against the blade.
22. WHEN cutting a large workpiece MAKE SURE the
material is supported at table height.
23. USE CAUTION when cutting material which is
irregular in cross section which could pinch the blade
before the cut is completed. A piece of moulding for
example must lay flat on the table and not be permitted
to rock while being cut.
24. USE CAUTION when cutting round material such
as dowel rods or tubing. They have a tendency to roll
while being cut causing the blade to “bite.” Use a Vblock to control the piece.
25. ALWAYS release blade tension before removing the
blade from the upper or lower blade holders.
26. MAKE CERTAIN table tilting lock is tightened
before starting the machine.
27. NEVER reach under the table while the machine is
running.
28. NEVER perform layout, assembly or set-up work on
the table while the saw is operating.
29. ALWAYS STOP the saw before removing scrap
pieces from the table.
30. WHEN THE TOOL IS NOT IN USE, the switch
should be locked in the “OFF” position to prevent
unauthorized use.
31. SHOULD any part of your Scroll Saw be missing,
damaged or fail in any way, or any electrical component
fail to perform properly, shut off switch and remove plug
from power supply outlet. Replace missing, damaged or
failed parts before resuming operation.
32. ADDITIONAL INFORMATION regarding the safe
and proper operation of this product is available from
the National Safety Council, 1121 Spring Lake Drive,
Itasca, IL 60143-3201, in the Accident Prevention
Manual for Industrial Operations and also in the Safety
Data Sheets provided by the NSC. Please also refer to
the American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machinery and
the U.S. Department of Labor OSHA 1910.213
Regulations.
33. SAVE THESE INSTRUCTIONS. Refer to them often
and use them to instruct others.
4
FOREWORD
Delta Model 40-570 16" Scroll Saw is designed to give high quality, smooth cutting performance with capacity to cut
up to 16" wide by 2" thick woodworking materials and has a 3/4" stroke. Delta Model 40-570 comes equipped with;
basic machine, integral dust port, variable speed 600-1650 spm, lock-out switch, cast iron table for minimal vibration,
Quickset II®Blade Chuck System for ergonomic “wrench-free” blade changing, threading and tensioning, accepts
wide variety of 5" flat end blades, 45° left tilting for bevel cuts, adjustable dust blower to keep cutting line free of dust.
UNPACKING AND CLEANING
Your new scroll saw is shipped completely assembled in the carton. Carefully unpack the saw and all loose items.
Remove the protective coating from the saw table surface. This coating may be removed with a soft cloth
moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover
the table surface with a good quality paste wax. Buff out the wax thoroughly to prevent it from rubbing into your
workpieces.
CONNECTING SCROLL SAW TO POWER SOURCE
POWER CONNECTIONS
A separate electrical circuit should be used for your tools. This circuit should be protected with a fuse or circuit
breaker. Have a certified electrician replace or repair a worn cord immediately. Before connecting power, make sure
the switch is in the “LOCKED OFF” position and the electric current is of the same characteristics as stamped on the
nameplate. Running on low voltage will damage the motor.
WARNING: DO NOT EXPOSE THE TOOL TO RAIN OR OPERATE THE TOOL IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Your scroll saw is wired for 110-120 volt, 60 HZ current. Before connecting the saw to the power source, make sure
the switch is in the “OFF” position.
0-6
0-6
0-6
0-6
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
Ampere
Rating
Volts
Total Length of
Cord in Feet
Gage of
Extension Cord
6-10
6-10
6-10
6-10
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
12-16
12-16
12-16
120
120
120
up to 25
25-50
14 AWG
12 AWG
GREATER THAN 50’ NOT RECOMMENDED
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16
12-16
12-16
240
240
240
240
240
240
240
240
240
240
240
240
240
240
240
up to 50
50-100
100-200
200-300
up to 50
50-100
100-200
200-300
up to 50
50-100
100-200
200-300
up to 50
50-100
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
GREATER THAN 100’ NOT RECOMMENDED
MINIMUM GAUGE EXTENSION CORD
EXTENSION CORDS
Use proper extension cord. Make sure your extension
cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power
and overheating. Fig. 1 shows the correct size to use
depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
Fig. 1
GROUNDING INSTRUCTIONS
WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR
FROM ELECTRIC SHOCK.
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with
insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor
to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or
if in doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and 3-pole receptacles that accept the tool’s
plug.
Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating less than 150
volts:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. 2. The tool
has a grounding plug that looks like the plug illustrated
in Fig. 2. A temporary adapter, which looks like the
adapter illustrated in Fig. 3, may be used to connect this
plug to a 2-pole receptacle as shown in Fig. 3 if a
properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded
outlet can be installed by a qualified electrician. The
green-colored rigid ear, lug, and the like, extending from
the adapter must be connected to a permanent ground
such as a properly grounded outlet box.
WARNING: IN ALL CASES, MAKE SURE THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. NEVER REMOVE GROUNDING
PRONG FROM POWER PLUG.
NOTE: In Canada, the use of a temporary adapter
is not permitted by the Canadian Electric Code.
5
Fig. 2
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE IS
LONGEST OF THE 3 BLADES
Fig. 3
GROUNDED OUTLET BOX
GROUNDING
MEANS
ADAPTER
6
FASTENING SCROLL SAW
TO SUPPORTING SURFACE
Your scroll saw MUST be securely fastened to a stand
or workbench using the three holes in the base, two of
which are shown at (A) Fig. 4.
IMPORTANT: If there is any tendency for the stand or
workbench to move during operation, the stand or
workbench MUST be fastened to the floor.
ON-OFF SWITCH AND VARIABLE
SPEED CONTROL
The on-off switch (A) Fig. 5, and variable speed control
(B) are located on the right front side of the scroll saw
base, as shown. To turn the saw “ON”, push the switch
(A) up and to turn the saw “OFF”, push the switch (A)
down.
This scroll saw is supplied with variable speed control
ranging from 600 to 1650 strokes per minute. Turn
variable speed control (B) Fig. 5, counterclockwise to
reduce speed and clockwise to increase speed.
LOCKING SWITCH IN
THE “OFF” POSITION
IMPORTANT: When the tool is not in use, the switch
should be locked in the “OFF” position. Grasp the
switch toggle (B) Fig. 6, and pull it out as shown. With
the switch toggle (B) removed, the switch, (A) Fig. 6, will
not operate.
FUSE REPLACEMENT
A fuse holder (A) Fig. 6A, and fuse (B) are located under
the rear of the machine and should be removed and
checked if the machine does not operate. If the fuse (B)
is bad, replace it with a 3 amp fuse.
Fig. 6
A
B
Fig. 5
A
B
CCW
CW
Fig. 4
A
Fig. 6A
A
B
7
TABLE INSERT
The table insert (A) can be assembled to the saw table
with the opening in the insert pointing to the front of the
table, as shown in Fig. 7, or to the right as shown in Fig. 8.
With the table in the level position, 90° to the blade, the
insert (A) should be positioned, as shown in Fig. 7. This
allows for the blade to be pivoted forward after it is
unclamped from the top blade holder, enabling you to
quickly insert the blade into the next hole in a pattern
when doing inside-cutting, as you will see later in this
manual.
When tilting the table for bevel cutting operations the
insert (A) should be positioned as shown in Fig. 8. This
allows for clearance of the blade when tilting the table.
A table insert blank (B) Fig. 9, is supplied as standard
equipment with your scroll saw and can be used when
cutting very small workpieces to give added support to
the bottom of the workpiece. Cut a slot into the blank
and replace the standard insert (A) with the blank (B). The
slot cut into the blank (B) will only be as wide as the
blade giving maximum support to the bottom of the
workpiece. Adhesive backed spacer pads (C) are also
supplied for adjusting the table insert height relative to
the table surface. Place three pads an equal distance
apart on a cleaned surface to be applied to the blank
insert. Pads can be stacked in order to achieve desired
insert height.
CHANGING BLADES
1. WARNING: TO AVOID INJURY FROM
ACCIDENTAL STARTING ALWAYS TURN SWITCH
“OFF” AND REMOVE SWITCH INSERT AND
DISCONNECT THE POWER CORD BEFORE
REMOVING OR REPLACING BLADE.
2. Remove table insert (A) Fig. 10, and release blade
tension by pulling tension lever (B) forward, as shown.
Fig. 7
Fig. 8
Fig. 9
A
A
B
A
C
Fig. 10
A
B
8
3. Push upper blade chuck locking lever (C) Fig. 11, to
the rear as shown. This will automatically release the
blade (D) from the upper chuck (E).
4. Remove the dust collection cup (A) by rotating knob
(B) 90° as shown in Fig. 12. Slide dust cup out of the
guides (C) by pulling it toward the front. NOTE: DO NOT
OPERATE THE UNIT WITH THE DUST CUP
REMOVED.
5. Push lower blade chuck locking lever (F) Fig. 13, to
the rear as shown. This will automatically release the
blade (G) from the lower chuck (H).
6. Insert new blade (I) into the upper blade holder (J)
making certain the blade teeth are pointing down
toward the table. Push upper blade chuck locking lever
(L) to the front as shown in Fig. 14. Insert new blade into
the lower blade holder Fig. 13 in the same manner.
7. Apply blade tension by referring to the following
section “ADJUSTING BLADE TENSION.”
Fig. 11
Fig. 12
Fig. 13
Fig. 14
C
D
E
B
C
A
G
F
H
I
J
L
K
9
ADJUSTING BLADE TENSION
Tension is applied to the blade when the blade tension
lever (A) Fig. 15, is in the rear position, as shown. When
the lever (A) is moved forward, as shown in Fig. 16,
blade tension is released.
To increase blade tension, turn lever knob (B) Fig. 16,
clockwise and to decrease blade tension, turn knob (B)
counterclockwise. When adjusting blade tension, lever
(A) should be in the forward position, as shown in Fig.
16. NOTE: It is necessary to adjust the blade tension
knob (B) only when the blade is removed from both
upper and lower blade holders and a new or different
type of blade is assembled to the holders. It is not
necessary to adjust blade tension when the blade is
removed and replaced in only the upper blade holder as
in performing inside cutting operations.
Adjusting the blade for proper tension is usually
accomplished by trial and error; however, a good
method to use is to pluck the rear of the blade, like a
guitar string, after the tension lever (A) Fig. 15, is moved
to the rear. A high-pitched tone of the blade should be
heard and this usually indicates proper tension. Finer
blades require more tensioning (a higher pitched sound)
while thicker blades require less tension.
ADJUSTING CLAMPING ACTION
OF UPPER AND LOWER BLADE
HOLDER CHUCK
Different widths of scroll saw blades will make it
necessary to adjust the clamping action of the upper
and lower blade holder chuck. It should be noted,
however, that very little adjustment is necessary and
very little clamping force is required to hold the blade
satisfactorily. As a rule of thumb, looking down at the
table with the table insert slot in the 6 o’clock position,
resistance on the blade locking lever should be felt
when the upper blade locking lever reaches the 7
o’clock position, or when the lower blade locking lever
reaches the 5 o’clock position.
1. Move the blade holder chuck locking lever (A) Fig.
17, to the rear (open) position, as shown.
2. Turn chuck clamping knob (B) Fig. 17, clockwise to
tighten and counterclockwise to loosen the clamping
action of the blade holder chuck. Very little movement of
knob (B) will be necessary. NOTE: Only the upper chuck
is shown. Clamping action of the lower chuck is
adjusted in the same manner and can be accessed by
removing dust cup shown in Fig. 12.
Fig. 16
Fig. 17
Fig. 15
A
A
A
B
B
Fig. 18
A
10
TILTING THE TABLE
The table on your scroll saw can be tilted 45° to the left
for bevel cutting operations by removing the dust cup
as shown in Fig. 12 and loosening table lock knob (A)
Fig. 18, tilt the table to the desired angle indicated on
degree scale (B) Fig. 19 and tighten lock handle (A) Fig.
18.
When bevel cutting, the holddown (B) Fig. 20, can be
adjusted to lay flat on the stock by loosening screw (C)
and tilting the holddown (B) accordingly. Then tighten
screw (C).
LEVELING THE TABLE
1. Loosen table lock knob as shown in Fig. 18 and
move the table all the way to the right until angle
indicator shown in Fig. 19 is on “0”.
2. Using a square that includes a level, check to see if
the table is level (A) Fig. 21, and is 90° to the saw blade
(B), as shown.
3. If the table is not at 90° to the blade, adjust the table
accordingly making certain screw (B) Fig. 22, contacts
bottom of table surface when table is 90° to the blade.
Screw (B) can be adjusted by loosening nut (C), turn
screw (B) in or out the desired distance and tighten nut
(C).
Note: After adjusting table, reposition the angle
indicator (B) Fig. 19 to "O" degrees.
Fig. 20
Fig. 22
Fig. 19
B
C
B
C
B
Fig. 21
A
B
90°
11
ADJUSTING HOLDDOWN
The holddown (A) Fig. 23, should be adjusted so it
contacts the top surface of the work (D) being cut by
loosening lock knob (B) and moving holddown rod (C)
up or down. Then tighten lock knob (B). The holddown
(A) Fig. 23, may be adjusted front to rear, by loosening
set screw (B) Fig. 24, and positioning the holddown in
the desired location. Once the holddown is in the
desired location, tighten set screw (B), Fig. 24.
ADJUSTING DUST BLOWER
The dust blower (A) Fig. 24, may be positioned to direct
air to the most effective point on the cutting line.
DUST COLLECTION CUP
A dust collection cup (A) Fig. 25 is provided and can be
attached to a shop vacuum system by utilizing the port
covered by cap (B).
INSIDE CUTTING
A blade threaded through a hole in the workpiece is
inside cutting. The Delta 16" Scroll Saw has the
capability of performing this operation quickly and
easily.
Loosen lock knob (A) Fig. 26, and raise the holddown
(B). Release blade tension by moving tension lever (C)
forward and loosen upper blade holder by moving lever
(D) to the rear as shown. This will release the blade (E).
Insert the blade (E) into the next hole in the pattern, as
shown.
Fig. 23
Fig. 24
Fig. 25
C
B
A
D
A
A
B
B
Fig. 26
A
B
D
C
E
Reassemble blade (E) Fig. 27, and tighten blade by
moving lever (D) forward (closed). Move tension lever
(C) to the rear as shown and lower holddown (B). You
are ready to make the next inside cut.
C
E
D
B
Fig. 27
12
CHOICE OF BLADE AND SPEED
Your scroll saw will accept a wide variety of 5" flat end
blades and can be operated at any speed from 600 to
1650 cutting strokes per minute. Consider the following
as a general guideline for selecting a blade and
operating speed.
1. Use a finer blade for cutting thin workpieces, for
hard materials, or when a smoother cut is required.
2. Use a coarser blade for cutting thick workpieces,
when making straight cuts or for medium to soft
materials.
3. Use a blade that will have 2 teeth in the workpiece at
all times.
4. Most blade packaging is marked with the size of the
wood the blade is intended to cut and the minimum
radius which can be cut with that blade.
5. Slower speeds are generally more effective than
faster speeds when using thin blades and making
intricate cuts.
6. Always start at a slow speed and gradually increase
the speed until the optimum cutting speed is obtained.
LUBRICATION
To keep the scroll saw operating at peak efficiency, we
recommend that a simple maintenance procedure be
performed after each 20 hours of use (approximately)
as follows:
1. MAKE CERTAIN THE MACHINE IS DISCON-
NECTED FROM THE POWER SOURCE.
2. Tilt the table 45° to the left as shown in Fig. 28.
3. Remove four rubber grommets (A) Fig. 29 that
cover the lubrication access holes.
4. Lubricate the pivot points in each of the four access
holes with a few drops of light machine oil as shown in
Fig. 30.
5. Reassemble the four grommets as shown in Fig. 29,
to machine.
6. Apply lightweight grease or anti-sieze to lubricate
the tensioning lever (A) Fig. 15 where it pivots on the
upper chuck .
Fig. 28
Fig. 29
Fig. 30
A
BLADE BREAKAGE
Blade breakage is usually caused by one or more of the
following:
1. Bending the blade during installation.
2. Improper blade tension.
3. Improper blade selection for the work being cut.
4. Forcing the work into the blade too rapidly.
5. Cutting too sharp a turn for the blade being used.
6. Improper blade speed.
13
FOLLOWING A LINE
With your scroll saw you should be able to cut a straight or curved line with ease. Most beginners will experience
blade wandering, however, they eventually learn to control it as they become more familiar with the machine. Use
scrap material to practice cuts before starting a project. This enables you to develop your own way of cutting and you
will find out what you can and cannot do with your saw.
Always hold the work firmly against the table and do not feed the workpiece too fast while cutting. Feed the workpiece
only fast enough so that the blade will cut. Scroll saws cut faster across the grain than they do with the grain. Allow
for this tendency when cutting patterns that shift rather quickly from with-the-grain cuts to cross-grain cuts.
Make “relief” cuts before cutting long curves and never attempt to cut a curve that is too tight for the blade being
used.
ACCESSORIES
The testing of this unit has been accomplished with the following accessories. For safest operation, it is recommended
that only these accessories be used with this unit.
WARNING: Since accessories other than those listed have not been tested with this unit, use of such
accessories could be hazardous.
CATALOG NO. DESCRIPTION
40-673 Assorted PGT®Scroll Saw Blades
25-869 Magnetic Work Light
SCROLL SAW BLADES
Catalog Number Material Cut Width Thickness Teeth Per Inch
40-058 Steel, Iron, Lead, Copper, Aluminum .070 .018 26
40-159 Pewter, Paper, Felt .075 .018 20
40-160 Steel, Iron, Lead, Copper, Brass .078 .022 15
40-161 Aluminum, Pewter .085 .022 15
40-164 Sheet Metal, Iron, Aluminum, Copper, .110 .018 20
Brass, Pewter, Lead, Wood
40-165 Mica, Brake Lining, Steel, Iron, Lead, .250 .028 20
Copper, Brass, Pewter, Aluminum
40-184 Wood Veneer, Plastics, Bakelite, Celluloid, .029 .012 20
Hard Rubber, Ivory, Extremely Thin Materials
40-185 Plastics, Celluloid .035 .015 15
40-187 Bakelite .090 .022 7
40-188 Ivory, Wood .100 .022 7
40-191 Wallboard, Pressed Wood, Lead, Wood, .110 .022 15
Bone, Felt, Copper, Paper, Ivory, Aluminum
40-192 Hard and Soft Wood .110 .022 10
40-193 Hard and Soft Wood .187 .025 10
40-194 Hard and Soft Wood .250 .028 7
40-195 Pearl, Pewter, Mica .041 .019 30
40-196 Pressed Wood, Sea Shells .065 .023 20
40-198 Hard Leather .085 .022 12
14
Delta Building Trades and Home Shop Machinery
Two Year Limited Warranty
Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine
accessory which in normal use has proven to be defective in workmanship or material, provided that the
customer returns the product prepaid to a Delta factory service center or authorized service station with
proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify
the alleged defect by inspection. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for
any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or
specifically authorized by anyone other than an authorized Delta Service facility or representative. Under no
circumstances will Delta be liable for incidental or consequential damages resulting from defective products.
This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to
defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose,
or otherwise, are expressly disclaimed by Delta.
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable•Delta
Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or
to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-888-848-5175 (In Canada call
1-800-463-3582).
Loading...