Delta 100, 140, 141, 300, 340 Installation Instructions Manual

SINGLE HANDLE
KITCHEN FAUCETS

You may need the following tools:

T

E

F

L

O

N

Write purchased model number here.

Models 100, 102, 103,
140, 141, 180, 300,
302, 340, 400, 402,
403, 440, 441, 480,
D111 & D411 Series

ASME A112.18.1 / CSA B125.1

®

1

50242 Rev. C

SILICONE

T

E

F

L

?

SILICONE

T

E

F

For easy installation of your
faucet you will need:

• To READ ALL the instructions

completely before beginning.

• To READ ALL warnings, care,

and maintenance information.

• To purchase the correct water

supply hook-up

.

11/1/08

®

U

P

C

TABLE OF CONTENTS:

Warranty -- - -- -- --- -- -- - -- -- - -- -- -- - -- -- - -- -- -- - -- -- - -- -- --- -- -- - -- -- - Page 2

Installation Instructions - -- -- -- -- - -- -- -- -- - -- --- -- - -- --- -- - -- --- -- - -- -- Pages 3- 8

Maintenance - -- - -- -- -- - -- -- - -- -- --- -- -- - -- -- - -- -- -- - -- -- - -- -- -- -- -- - Page 9

Replacement Parts - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - - Pages 1 0- 1 7

2

All parts and finishes of the Delta® faucet are
warranted to the original consumer purchaser to
be free from defects in material & workmanship
for as long as the original consumer purchaser
owns their home. Delta Faucet Company
recommends using a professional plumber for all
installation & repair.

Delta will replace, FREE OF CHARGE, during
the warranty period, any part or finish that proves
defective in material and/or workmanship under
normal installation, use & service. Replacement
parts may be obtained by calling 1-800-345­DELTA (in the U.S. and Canada) or by writing to:

In the United States:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280

In Canada:
Masco Canada
Technical Service Centre
420 Burbrook Place
London, ON N6A 4L6

This warranty is extensive in that it covers
replacement of all defective parts and even
finish, but these are the only two things that
are covered. LABOR CHARGES AND/OR
DAMAGE INCURRED IN INSTALLATION,

Lifetime Faucet and Finish Limited Warranty

REPAIR, OR REPLACEMENT AS WELL AS ANY
OTHER KIND OF LOSS OR DAMAGES ARE
EXCLUDED. Proof of purchase (original sales
receipt) from the original consumer purchaser
must be made available to Delta for all warranty
claims. THIS IS THE EXCLUSIVE WARRANTY
BY DELTA FAUCET COMPANY, WHICH DOES
NOT MAKE ANY OTHER WARRANTY OF ANY
KIND, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY.

This warranty excludes all industrial, commercial
& business usage, whose purchasers are
hereby extended a five year limited warranty
from the date of purchase, with all other terms of
this warranty applying except the duration of the
warranty. This warranty is applicable to Delta

®

faucets manufactured after January 1, 1995.
Some states/provinces do not allow the exclusion

or limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you. Any damage to this faucet
as a result of misuse, abuse, or neglect, or any
use of other than genuine Delta® replacement
parts WILL VOID THE WARRANTY.

This warranty gives you specific legal rights, and
you may also have other rights which vary from
state/province to state/province. It applies only
for Delta

®

faucets installed in the United States of

America, Canada, and Mexico.

© 2008 Masco Corporation of Indiana

1

3

2

1

1

1

Remove old faucet. For deck mount
models place gasket (1) on faucet.
For single hole mount models, place
base (1) then gasket (2) on faucet.
For models without spray, go to
Step 3. For models with spray, go
to Step 2.

SHUT OFF WATER SUPPLIES

NOTE: Thick tile 2 1/2" mounting

kits available.
140,180, 340, 440 & 480 Series–
RP30393.
103, 141, 403 & 441 Series–

RP30394.

Deck Mount

Deck Mount

Single Hole Mount

Preparing for Installation

4

2

1

1

2

3

3

Mount the spray support assembly (1)
in far right hole in sink. Hand tighten
nut. Insert spray hose (2) down through
support assembly and up through center

For models with spray and spray support.

2

Sprayer Installation

hole on sink. Snap quick connect spray
hose (2) onto spray hose nipple (3). Pull
down moderately to ensure connection
has been made. Go on to Step 2.

2

2

1

3

2

Insert spray hose (1) down through support
assembly on escutcheon and hole in
sink. From underneath the sink place the
mounting nut (2) over spray hose and
insert the hose up through the middle hole

For models with integrated spray.

Sprayer Installation

in sink. From above the sink, snap the
quick connect spray hose (1) onto the
spray hose nipple (3) with quick connect
fitting. Pull down moderately to ensure
connection has been made.

5

6

3

1

1

2

2

Feed tubes (1) down through cen­ter hole in sink. OPTION: If sink is

uneven, use silicone sealant under the
gasket. Secure faucet to sink

with nuts/washers or mounting
nuts (2) supplied with your faucet.

For deck mount models.

Faucet Installation

Deck Mount

Single Hole Mount

Feed tubes (1) down through center hole
in sink. OPTION: If sink is uneven, use
silicone sealant under the gasket. Secure
faucet to sink with mounting bracket,
spacer (for thin mount only) and nut (2)
supplied with your faucet.

For single hole mount models.

2

2

2

7

4

1 2

3

1/2" (12.70mm) IPS

A.

Note: Be careful when bending the

copper tubing. Kinked tubes will void
the warranty. Choose hook-ups for 1/2"

I.P.S. connections: (1) Ball nose riser
(3/8" O.D. copper tubing), or (2) 1/2"
I.P.S. faucet connector. Use the enclosed
coupling nuts (3) with the ball nose risers
(1). Coupling nuts are not included with
D111, D311 or D411 Series. Important:

Use two wrenches when tightening.
Do not overtighten.

A.

B.

1

2

B.

Note: Be careful when bending the

copper tubing. Kinked tubes will
void the warranty. Solder connections

(1) or use compression fittings (2) for
3/8" O.D. (1/4" nominal) copper tubing.

Supply Line Connections

For models with fittings.

For models without fittings.

8

5

2

3

1

Remove aerator (1) and turn faucet
handle (2) to the full on mixed position.
Turn on hot and cold water supplies (3)
and flush water lines for one minute.

Important: This flushes away any
debris that could cause damage to
internal parts.

Check all connections at arrows for
leaks. Re-tighten if necessary, but do
not overtighten.

Flush the System and Check for Leaks

9

3

2

4

7

6

1

If faucet leaks from under handle:

Remove handle and ensure cap (1) is tight.
If leak persists–SHUT OFF WATER

SUPPLIES. Replace Ball Assembly
(2)–Repair Kit RP70 and Cam & Packing
(3)–Repair Kit RP61.

If faucet leaks from spout outlet:

SHUT OFF WATER SUPPLIES. Replace
Ball Assembly (2)–Repair Kit RP70 and
Seats & Springs (4)–Repair Kit RP4993.

If faucet exhibits very low flow

A. Remove and clean Aerator (5), or
B. SHUT OFF WATER SUPPLIES. Clean
Seats and Springs (4) of any debris.

If spray attachment does not
function properly:

SHUT OFF WATER SUPPLIES. Remove
Diverter Assembly (6) and clean.

If condition persists–SHUT OFF WATER
SUPPLIES. Replace Diverter Assembly
(6)–Repair Kit RP320.

If faucet leaks from base of spout:

SHUT OFF WATER SUPPLIES. Remove
spout and replace Spout O-Rings (7)–Repair
Kit RP25.

1/8" (3.18mm)

5

Maintenance Cleaning and Care

Care should be given to the cleaning
of this product. Although its finish is
extremely durable, it can be damaged
by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth
and blot dry with a soft towel.

Notes / Notas / Notes

LLAVES DE COCINA
DE PALANCA

Usted puede necesitar:

T

E

F

L

O

N

Escriba aquí el número del modelo comprado.

Modelos 100, 102, 103,
140, 141, 180, 300,
302, 340, 400, 402,
403, 440, 441, 480,
D111 y D411 Series

ASME A112.18.1 / CSA B125.1

®

1

50242 Rev. C

SILICONE

T

E

F

L

?

SILICONE

T

E

F

Para instalación fácil de su
llave Delta usted necesitará:

• LEER TODAS las instrucciones

completamente antes de empezar.

• LEER TODOS los avisos,

cuidados, e información de
mantenimiento.

• Comprar las conexiones correc

-

tas para el suministro de agua.

11/1/08

®

U

P

C

2

Todas las piezas y acabados de la llave Delta®
están garantizados al consumidor comprador
original, de estar libres de defectos de material
y fabricación, por el tiempo que el consumidor
comprador original sea dueño de su casa. Delta
Faucet Company recomienda que use un
plomero profesional para todas las instalaciones
y zreparaciones.

Delta reemplazará, LIBRE DE CARGO, durante
el período de garantía, cualquier pieza o
acabado que pruebe tener defectos de material
y/o fabricación bajo instalación normal, uso y
servicio. Piezas de repuesto pueden ser
obtenidas llamando al 1-800-345-DELTA (en los
Estados Unidos y Canada) o escribiendo a:

En los Estados Unidos:

Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280

En Canada:

Masco Canada
Technical Service Centre
420 Burbrook Place
London, ON N6A 4L6

Esta garantía es extensiva en lo que cubre el
reemplazamiento de todas las piezas
defectuosas y hasta el acabado, pero éstas
son las únicas dos cosas que están cubiertas.
CARGOS DE LABOR Y/O DAÑOS INCURRIDOS
EN LA INSTALACIÓN, REPARACIÓN, O
REEMPLAZAMIENTO COMO TAMBIÉN

Garantía Limitada De Por Vida de la Llave y su Acabado

CUALQUIER OTRO TIPO DE PÉRDIDA O
DAÑOS ESTÁN EXCLUÍDOS. Prueba de
compra (recibo original de venta) del comprador
consumidor original debe de ser disponible a
Delta para todos los reclamos. ESTA ES LA
GARANTÍA EXCLUSIVA DE DELTA FAUCET
COMPANY, QUE NO HACE CUALQUIER
OTRA GARANTÍA DE CUALQUIER TIPO,
INCLUYENDO LA GARANTÍA IMPLÍCITA DE
COMERCIALIZACIÓN.

Esta garantía excluye todo uso industrial,
comercial y de negocio, a cuyos compradores
se les da una garantía limitada extendida de
cinco años desde la fecha de compra, con todos
los otros términos de esta garantía aplicados,
excepto el de duración de ésta. Esta garantía
es aplicable a las llaves de Delta® fabricadas
después de Enero 1, 1995.

Algunos estados/provincias no permiten la
exclusión o limitación de daños incidentales o
consecuentes, de manera que la limitación o
exclusión arriba escrita puede no aplicarle a
usted. Cualquier daño a esta llave, resultado del
mal uso, abuso, o descuido, o cualquier otro uso
de piezas de repuesto que no sean genuinas de
Delta® ANULARÁN LA GARANTÍA.

Esta garantía le da derechos legales específicos,
y usted puede, también tener otros derechos que
varían de estado/provincia a estado/provincia.
Es aplicable sólo a las llaves Delta® instaladas
en los Estados Unidos de America, Canada
y Mexico.

© 2008 Masco Corporación de Indiana

Índice:

Garantía - -- -- - -- -- - -- -- --- -- -- - -- -- - -- -- -- - -- -- - -- -- -- - -- -- - -- -- --- -- Página 2

Instrucciones para la Instalación - - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- Páginas 3 -8

Mantenimiento - -- - -- -- -- - -- -- - -- -- --- -- -- - -- -- - -- -- -- - -- -- - -- -- -- -- - Página 9

Piezas de Repuesto - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - -- - -- -- - Páginas 1 0- 17