Delonghi TRDX41025E Instruction manuals
DESCRIPTION
❶
❷
A ON/STAND-BY button
B timer button
C control dial/dial button
D display
E wheel
F cord holder
Symbols shown on the unit's display
key-lock
power supply
temperature/clock
selected power levels
working power levels
Anti-frost symbol
timer function
l (green) Temperature 1 (T1) indicator
l (red) Temperature 2 (T2) indicator
FIRST USE
"Easy wheel" system
Turn the radiator upside down on a rug or a soft surface in
order to prevent damaging the paint nish.
Fully unfold the wheels by turning them outwards (Fig. 1).
Turn the radiator back to its upright position.
Setting the time
When using for the rst time or after it has been unplugged
for a long time, you need to set the current time:
1. Plug the appliance into the mains. The display will show
00 blinking.
2. Turn the control dial to select the current hour.
3. When the correct hour is set, press the dial and the minutes digits will blink.
4. Turn the control dial to set the minutes then press the
dial to conrm.
Example of display:
❸
Changing the time
If you need to reset the time, in manual operation mode press
the control dial for 5 seconds, then proceed as explained
above. After setting the clock, the unit will return in manual
operation mode.
❹
Fig. 1
Location
The heater must not be placed immediately below a power
outlet. Do not use this radiator in rooms having a surface area
of less than 43 square feet (4 sq.m.).
Power connection
Before using the appliance check that your supply voltage is
the same of that shown on the rating label of the unit and
that the power socket and power supply line correspond to
the load specied. After plugged in the appliance will shows
the symbol in red colour.
MANUAL OPERATION MODE
Turn the appliance on pressing the button .
The unit will start operating in manual operation mode with
the following default settings:
Setting the temperature
To modify the temperature set point, turn the dial clockwise
to increase and anticlockwise to decrease the temperature.
Temperature settings available are 5°C, and 10°C through to
28 °C. Setting to 5°C turns the unit to the antifrost function.
(see Antifrost function at page 6).
10
Selected power levels and working power levels
min
]
]
❷
❶
❷
There are 3 power levels (min/med/max) as well as ECO
mode.
med max max + eco
Depending on the selected power level, the working power
level may be less or equal to the selected power level.
The working heating power is always shown by the unit’s
display by means of the thin bars below the selected power
level.
Selected power level
Working power level
- If the current room temperature is much lower than the
selected temperature, the appliance will start to heat
the room as rapidly as possible at the selected power
level.
- If the current room temperature is close to the selected
temperature, the appliance will heat the room using a
heating power lower than the selected power level.
- When the selected temperature is reached, the unit
stops heating.
Example: Operation is started at room temperature 18°C, the
set temperature is 25 °C, and the selected power level is Max.
Example of display:
Room temperature 18°
❶
Working power level: Max
Room temperature 24° Room temperature 25°
❸
Room temperature 22°
Working power level: Med
❹
Setting the power level
1. Press the dial twice during heating operation.
2. The power level will blink.
3. Choose one of the available power levels by turning the
dial.
4. Press the dial once to conrm.
Example of display:
❸
❹
Eco mode
When the eco mode is activated, the unit will automatically
select the most convenient working power level from Max
to Min, and will also control the set temperature in order to
achieve energy saving while guaranteeing optimum comfort.
Anti-frost function
This function is useful to prevent freezing.
To activate this function, in manual operation when temperature is set to 10°C turn the dial anticlockwise till the set point
5 is displayed and a will appear.
Working power level: Min
The room temperature is
reached the appliance
stops heating
In this operation mode the working power can not be set.
The appliance will automatically set to Max power level.
If you turn the dial clockwise, you will restore the same power
setting as before being switched to anti-frost.
11
Loading...