De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com
5711413321_00_0418
Proudly distributed by
De’Longhi Australia Pty Limited
P.O. BOX 4540
CASULA MALL NSW 2170
Customer Service Ph: 1800 126 659
Fax: 1800 706932
www.delonghi.com.au
e-mail: info.au@delonghigroup.com
De’Longhi New Zealand Limited
99 Khyber Pass Road
Grafton 1023
Auckland, New Zealand
P.O. Box 58-056 Botany
MANUKAU 2163
Customer Service Ph: 0508 200 300
Fax: 0508 200 301
www.delonghi.co.nz
e-mail: info.nz@delonghigroup.com
HFX85W20
AIR PURIFIER, HEATER AND COOLING FAN
Instructions for use
This product is only suitable for well insulated spaces or occasional use
2
3
A
A
M1
D
K1
G1
N
F1
H1
P
E
L1
O
FM
GL
H
I
S
Q
R
K
J
C
B
4
IMPORTANT WARNINGS
Safety warnings
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
- Do not locate the heater immediately
below a socket-outlet.
- Do not use this heater in the immediate surroundings of a bath, a shower or
a swimming pool.
- If the supply cord is damaged, it must
be replaced by the manufacturer or its
service agent or a similarly qualied
person in order to avoid a hazard.
Important!
Failure to observe the warning could result in injury or damage to the appliance.
- The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given supervised or instruction concerning use of the appliance by a responsi-
ble person for their safely.
Young children should be supervised
to ensure that they do not play with
the appliance.
- CAUTION: To avoid the safety system
resetting accidentally, this appliance
must not be powered through an external on/o device such as a timer, or
connected to a circuit which is turned
o and on regularly by the energy supplier.
- WARNING: Do not use this heater in
small rooms when they are occupied
by persons not capable of leaving the
room on their own, unless constant
supervision is provided.
Danger of burns!!
Failure to observe the warning could result in burns or scalds.
- WARNING: In order to avoid
overheating, do not cover the
heater during operation as this
would lead to a dangerous rise in temperature.
- WARNING: to reduce the risk of re,
keep textiles, curtains, or any other
ammable material a minimum distance of 1 m from the air outlet.
Safety functions
- Safety device: the appliance is tted
with a safety device which switches it
o in the event of accidental overheating (e.g. obstruction of air intake and
outlet grilles, motor turning slowly or
not at all).
To reset, unplug the appliance from
the mains socket for a few minutes,
remove the cause of overheating then
plug in again. If the appliance doesn’t
work please contact the De’Longhi
Customer Service.
- Tip over safety device: Certain mod-
els are tted with a tip-over switch
which turns the appliance o if it falls
over. To restart the appliance, simply
place it upright again.
Please note:
This symbol indicates recommendations and important information for the user.
- Use this heater on a horizontal and stable surface.
- Always use the appliance in an upright
position.
- Do not use this heater if it has been
dropped.
- Do not use if there are visible signs of
5
damage to the heater.
- The use of extension leads is not recommended.
However if they cannot be avoided,
follow the instructions accompanying
the extension lead and never exceed
the power limit marked on the extension.
- The heater must be positioned at least
50 cm from furniture or other objects.
- Do not use the appliance near walls,
furniture, curtains, etc.
- Do not use the appliance in rooms with
a oor area of less than 4m2.
- Before putting the appliance away,
make sure it is completely o and unplugged from the mains socket.
Do not store in dusty atmospheres.
- Do not rest anything on the appliance.
- Do not use the appliance to dry laundry. Do not obstruct the air intake and
outlet area (danger of overheating).
- The appliance must not be hung.
- Some models are supplied with a device which delays of few seconds the
fan shut o.
Important!
- WARNING - KEEP BATTERIES OUT
OF REACH OF CHILDREN.
- Swallowing may lead to serious injury
in as little as 2 hours or death, due to
chemical burns and potential perforation of the oesophagus.
- Examine devices and make sure the
battery compartment is correctly secured. Do not use if compartment is
not secure.
- Dispose of used button batteries immediately and safely. Flat batteries can
still be dangerous.
INTRODUCTION
Thank you for choosing a De’Longhi product. Please take a
few minutes to read these instructions. This will avoid all risks
and damage to the appliance.
DESCRIPTION
A ON/STAND-BY button
B Lid release button
C Air purication lter
D Remote control
E Control panel
F Heating button
F1 Heating mode
G Temperature buttons
G1 Temperature indicator (C° and F°)
H ECO button
H1 ECO function
I Airow direction button
J Oscillation button
K Timer button
K1 Timer function
L Fan speed buttons
L1 Fan speed indicator
M Cooling fan button
M1 Cooling fan mode
N Hours
O Power indicator light
P Receiver for remote control
Increase button
Decrease button
Q Handle
R Air inlet
S Air outlet
OPERATION AND USE
Electrical connection
Before plugging the appliance into the mains socket, check
that the mains power supply corresponds to the value
indicated on the rating plate and that the mains power
supply is adequate for the load.
Installation
The appliance can be used on any horizontal stable surface.
Do not overload the electrical circuit.
Avoid using the same socket for other appliances.
Please note: the appliance can be easily moved
carring it by the handle. Before moving it remember to turn
it o.
6
Starting instructions
Please note: the lter is provided with a protective
wrapper around it that needs to be removed before rst use.
- Before turning on the appliance extract the lter from
its housing as explained in the lter maintenance
section.
- Remove the wrapper covering the lter (g.1).
g.1
- Replace the lter in its housing as explained in the lter
maintenance section.
- Connect the appliance to the power outlet.
- The appliance emits three beeps and the power
indicator light (O) also comes on and remains lit while
power to the appliance is on. The appliance goes into
STAND-BY.
OPERATING MODES
Turn on the appliance
- Press/touch the ON/STAND-BY button (A) to turn on the
appliance.
There are two buttons to select the operating modes of
the appliance: heating (F) and cooling fan (M).
- To turn o the appliance press/touch button ON/STANDBY (A). The display could show the count down for
about 10 seconds. After that, to completely turn o the
appliance, remove the plug from the socket.
Please note: never turn o the appliance by only
pulling the plug. Press/touch the ON/STAND-BY button
(A) and wait a few minutes before pulling the plug. In this
manner, the appliance can perform the operating status
checks.
Air purication
The product is designed to oer constant air purication from
allergens and pollutants.
The purication function is automatically activated both in
heating and cooling fan modes.
If air purication is desired regardless of the need for heating
or ventilation, it is advisable to set the product in cooling fan
mode using ventilation levels 1 through 5.
Heating mode
- To select this operating mode, press the heating button
(F) on the remote control, the display shows the
symbol (F1); the temperature can be set by pressing
the temperature buttons (
or ) (G) on the remote
control.
At rst pressing, the display will show the current setpoint for some seconds (approx 4-5) together with
the symbol; the temperature can be increased or
decreased by pressing button or respectively.
- The minimum setting is 10°C (50°F) and the maximum
is 28°C (82°F).
- In this mode it is possible to increase or decrease the
fan speed by pressing respectively the speed button
or (L) on remote control; the minimum fan speed
available in heating mode is 1, the maximum is 6.
-
At rst pressing, the display will show the current fan
speed for some seconds (approx 4-5) together with the
symbol.
Please note: the appliance will operate for few
seconds with a reduced airow to allow the preheating in
order to guarantee the best comfort.
Please note: When the set temperature is reached, the
appliance will automatically stop heating, but it may keep
working for a preset time at reduced airflow speed.
The appliance will restart heating again, at the previous
heating settings, as long as needed to maintain the desired
set temperature.
Examples: heating mode
- Press heating button (F), the display shows .
7
- Press the temperature button or (G) to select
desired temperature (within 4/5 seconds).
- Press the speed button or (L) to increase or
decrease the fan speed (within 4/5 seconds).
ECO function
This function can be activated only inside the heating
operating mode.
To activate this function, press the ECO button (H) on the
remote control, the display shows .
The appliance will automatically set the power level
to guarantee the best comfort reducing the energy
consumption.
Cooling fan mode
In this operating mode only the fan operates, so the appliance
does not heat the room. This is ideal during summer days
because it moves cool air in a room, creating a cool draft
instead of stale air.
- To select this operating mode, press the cooling fan
button (M) on the remote control, the display shows
the symbol (M1).
-
In cooling fan mode 10 fan speeds are available. It's
possible to increase or decrease the fan speed by pressing
respectively the speed button or (L) on the remote
control. The value changes of 1 speed at a time.
- At rst pressing, the display will show the current fan
speed.
Examples: cooling fan mode
- Press cooling fan button (M) , the display shows the
symbol .
- Press the speed button or (L) to increase or
decrease the fan speed (within 4/5 seconds) the display
will show the fan speed.
TIMER operation
The timer can be used to delay appliance start up or
shutdown. This avoids wasting electricity by not operating
the appliance when it is not needed.
This function can be activated from any operating mode.
- DELAYED SWITCHON: with the appliance in the
STAND-BY position, press the timer button (K) on
the remote control, the display shows the symbol
(K1) together with "h" (N). The time can be set pressing
the timer button again. The available values are the
following: 0.5h; 1h; 2h; 4h; 6h; 8h; 12h.
Once having set the desired time, to conrm wait about
4-5 seconds.
When the programmed time has been reached, the
appliance turns on with the same settings it had during
the previous operation.
Once the function has been set, if you want to go back
to operation without the timer, press the timer button
(K) twice. The timer symbol disappears from the
display.
-
DELAYED SHUTOFF: With the appliance on, press the
timer button (K) on the remote control, the display
shows the symbol (K1) together with "h" (N). The
time can be set pressing the timer button again. The
8
available values are the following: 0.5h; 1h; 2h; 4h; 6h;
8h; 12h. Once having set the desired time, to conrm wait
about 4-5 seconds. When the programmed time has been
reached, the appliance shuts o automatically.
Once the function has been set, if you want to go back
to operation without the timer, press the timer button
(K) twice.
The timer symbol disappears from the
display.
Please note: while the timer is active, the operating
settings of the unit can be modied.
Please note: while this funtion is active, if the timer
button is pressed one time, the remaining time will be shown
on the display.
Please note: if a power failure occurs, the timer
function is reset and the appliance goes to standby.
Please note: if the ON/STAND-BY button is pressed
while the timer function is active, the unit changes its status
(for example it goes in ON from STAND-BY or viceversa) and
timer function will be deactivated.
Examples: timer function
- In heating mode press one time the timer button, 6h
appears on display, press again the timer button to the
desired value within 4/5 seconds. Then wait approx 4/5
seconds for saving.
Oscillation button
If you want the appliance to distribute the airow over a
larger area, press the oscillation button (J) on remote control.
The appliance will then oscillate right and left.
To stop the oscillation in the desired position, just press
oscillation button (J) again.
Please note: never try to rotate the appliance
manually.
Please note: when changing the settings, the
oscillation temporarily stops.
Airow
The airow moves around the surface of the appliance
spreading uniformly throughout the room, ensuring a perfect
comfort in the room.
Important! NEVER put your hands or any foreign
objects e.g. a knife or foil, into the air outlet (S).
Airow direction
This function allows to orientate the airow in the best way.
There are two positions, "H" and "L" (high and low direction).
Once the button airow direction (I) is pressed, the buzzer
emits a sound and the display shows "H" or "L" for a few
seconds.
Examples of the display of airow direction:
9
Change the temperature scale
To change the temperature scale press together the
of temperature buttons (G) and of speed buttons (L)
on remote control, an acoustic signal will be emitted and
the display will show for 3 seconds "F" (Fahrenheit) or"C"
(Celsius) with the simbol .
No beep function
This function allows to activate or deactivate the buzzer
placed on the control panel.
Press together airow direction button (I) and oscillation
button (J).
The display shows the script "nb" for a few seconds, then the
normal visualization reappears. This function is available in
any operating mode, including standby.
Examples: no beep function
Please note: the buzzer shall generate the sounds
related to the commands "stand-by" and "turning on"
regardless of this function.
Brightness of the display
The appliance allows two dierent brightness settings for the
display. The highest is active when any key button is pressed.
After a few seconds of keyboard inactivity, the brightness will
decrease to the operating brightness level.
To change the operating brightness level, press the eco
button (H) and timer button (K) together; three brightness
levels are available, the display shows: "L1", "L2", "L3" for 4-5
seconds, and within this time is possible increase or decrease
the brightness level using the speed buttons (L), or
respectively.
Elapsed the 4-5 seconds, the last level of brightness selected
will be shown on the display.
Examples: brightness of the display:
Remote control: inserting or replacing the batteries
- The remote control
is provided with
a lithium button
battery CR2032. To
let the appliance
function, remove the
battery cover strip, by
pulling it.
- To replace the
batteries, remove the
battery cover by rotating the screw counterclockwise
with a screwdriver. Replace the battery paying attention
to respect the right polarity as shown in gure.
- Replace the cover rotating the screw clockwise.
- Old batteries must be removed and disposed o in
accordance with current legislation as they are harmful
to the environment.
WARNING: DO NOT DISPOSE OF BATTERIES IN FIRE.
BATTERIES MAY EXPLODE OR LEAK.
Operating from the control panel
To use the unit the remote control is needed.
If the remote control is not available, it's possibile to switch
the operating mode between cooling fan and heating by
means of the ON/STAND-BY button (A) on the control panel.
While the unit is in STAND-BY mode, keeping touched the
ON/STAND-BY button for approx. 10 seconds, the unit is
turned on with predened setting.
10
The appliance comes on with the opposite function set before
it was shut o with a predened temperature set in case of
heating and a predened speed in cooling fan.
MAINTENANCE
General product maintenance
Before carrying out any maintenance, always unplug from
the mains socket.
Please note: during the season when the appliance is
in use, clean the air intake and outlet grilles regularly using a
vacuum cleaner.
Please note: never use abrasive powders or solvents
to clean the appliance.
Use only a soft damp cloth to clean the appliance.
Air purication lter maintenance
It is good practice to clean the lter at regular intervals to
remove accumulation of dust on the surface of the lter.
To clean the lter, it is necessary to remove it from its housing
as explained below:
- Open the lid by pushing the lid release button (B).
- Rotate the lter cover anticlockwise until the pointer on
the cover matches the symbol (g.2).
g. 2
- Remove the lter .
- Use a vacuum cleaner to remove the dust collected.
- Then put the lter back in its housing by rotating the
cover clockwise until the pointer on the cover matches
the symbol (g.3).
Please note: never close lid forcibly, when lter is set
improperly.
g. 3
The unit is automatically programmed to remind you to
change the lter.
After a predened number of working hours the unit will
display CF message cyclically, indicating that the lter must
be replaced. Always use original De'Longhi lters.
To reset the CF alarm, in rapid succession insert the plug and
touch and hold the ON/STAND-BY (A) button on the unit for
at least 10 seconds until you hear a long beep.
The lter is designed to last up to 9 months, based on 8 hours
usage a day, at medium working load.
Please note: the indicator is a guide and you may
need to replace the lter more frequently, depending on the
air quality conditions.
TECHNICAL CHARACTERISTICS
Supply voltage See rating plate
Absorbed power “
11
PROBLEM CAUSE SOLUTION
The display shows "pf" and emits
a beep
Temperature sensors are not working
properly
Please contact Customer Service
Product doesn’t turn on Check that the plug is connected to the
outlet
The set temperature has been reached
or the time set on the timer has elapsed
Plug in
Use the “+” button to increase the set
temperature
The appliance goes o unexpectedly Check that the plug is connected to the
outlet
The set temperature has been reached
or the time set on the timer has elapsed
Plug in
A dot is ashing on display, emits a
beep and unit is o
The tip-over switch has been activated Make sure the appliance is standing
upright on a at surface.
If the appliance doesn’t work please contact Customer Service
The display shows "cf"
The lter has reached the predened
number of hours
Replace the lter and reset the alarm.
To reset the CF alarm, in rapid
succession insert the plug and touch
and hold the ON/STAND-BY (A) button
on the unit for at least 10 seconds until
you hear a long beep.
TROUBLESHOOTING
12
The display shows "Ht" or "It" blinking
The internal temperature is too high.
The air intake or outlet grille is
obstructed
Check the appliance is correctly
positioned respecting the minum
distances from the wall, or objects, as
indicated on the instruction manual,
if not, position the appliance correctly
Remove the obstruction
Disconnect the plug from the outlet
and let the appliance cool down. After
few minutes plug the appliance again.
If the appliance doesn't work
please
contact Customer Service
The display shows "Fi"
The fan motor does not work Disconnect the plug from the outlet.
After few minutes plug the appliance
again. If the problem persists
please
contact Customer Service
Loading...