Page 1
Proudly distributed by
De’Longhi Australia Pty Limited
P.O. BOX 4540
CASULA MALL NSW 2170
Customer Service Ph: 1800 126 659
Fax: 1800 706932
www.delonghi.com.au
e-mail: info.au@delonghigroup.com
De’Longhi New Zealand Limited
99 Khyber Pass Road
Grafton 1023
Auckland, New Zealand
P.O. Box 58-056 Botany
MANUKAU 2163
Customer Service Ph: 0508 200 300
Fax: 0508 200 301
www.delonghi.co.nz
e-mail: info.nz@delonghigroup.com
De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com
5711413491_00_1017
Page 2
HFX60V20
CERAMIC FAN HEATER
Instructions for use
Page 3
G
I
D
B
E
F
C
A
A
D
B
E
F
C
H
2
Page 4
IMPORTANT SAFEGUARDS
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
- The appliance must not be placed immediately under a xed power socket.
- Do not use the appliance near showers, bathtubs, sinks, swimming pools,
etc.
- If the power cable is damaged, it must
be replaced by the manufacturer, an
authorised service centre or a qualied
electrician in order to eliminate all risk.
Important!
Failure to observe the warning could result in injury or damage to the appliance.
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to en-
sure that they do not play with the
appliance.
CAUTION — Some parts of this
product can become very hot and
cause burns. Particular attention
has to be given where children
and vulnerable people are present.
- ATTENTION: To avoid the safety system resetting accidentally, this appliance must not be powered through
an external on/o device such as a
timer, or connected to a circuit which
is turned o and on regularly by the
energy supplier.
- Do not use the appliance in small
rooms when they are occupied by persons that are not capable of leaving
the room, unless constant supervision
is provided.
Danger of burns!!
Failure to observe the warning could result in burns or scalds.
- WARNING: To avoid overheating, never under any circumstances cover the appliance
during operation as this would lead to
a dangerous rise in temperature.
Please note:
This symbol indicates recommendations and important information for the user.
- Always use the appliance in an upright position.
- The use of extension leads is not recommended.
However if they cannot be avoided, follow the instruc-
tions accompanying the extension lead and never exceed the power limit marked on the extension.
- The heater must be positioned at least 50 cm from furniture or other objects.
- Do not use the appliance in rooms with a oor area of
less than 4m2.
- Before putting the appliance away, make sure it is completely o and unplugged from the mains socket. Wrap
the cable around the base.
Do not store in dusty atmospheres.
- Do not rest anything on the appliance.
- Do not use the appliance to dr y laundry. Do not obstruct
the air intake and outlet grilles (danger of overheating).
- Do not use the appliance near walls, furniture, curtains,
etc.
Safety functions
- Safety device: the appliance is tted with a safety
device which switches it o in the event of accidental
overheating (e.g. obstruction of air intake and outlet
grilles, motor turning slowly or not at all).
To reset, unplug the appliance from the mains socket for
a few minutes, remove the cause of overheating then
plug in again.
If the appliance doesn't work please contact the
De'Longhi Customer Service.
- Tip over safety device: a tip over safety device turns
the appliance o if it falls over or is positioned inappropriately in such a way as to jeopardise safety.
3
Page 5
The appliance emits a beep and a dot ashes on the
display. The appliance resumes operation a few seconds
after being placed in an upright position again.
INTRODUCTION
Thank you for choosing a De’Longhi product.
Please take a few minutes to read these instructions.
This will avoid all risks and damage to the appliance.
DESCRIPTION
A ON/STAND-BY button
B +/- Adjustment buttons
C Oscillation button
D “ECO PLUS” function button
E Timer button
F MODE button (for selecting the operating mode)
G Power indicator light
H Back cover with lter
I Receiver for remote control (certain models only)
USE
Installation
The appliance can be used on any horizontal surface.
Do not overload the electrical circuit. Avoid using the same
socket for other appliances.
Electrical connection
- Before plugging the appliance into the mains socket,
check that the mains power supply corresponds to the
value indicated on the rating plate and that the mains
power supply is adequate for the load.
- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/
EEC ON RADIO INTERFERENCE SUPPRESSION.
Operation and use
- Connect the appliance to the power outlet.
- The appliance emits a beep and the power indicator
light (G) also comes on and remains lit while power to
the appliance is on. The appliance goes into STAND-BY.
- Press the ON/STAND-BY button (A) to turn on the appliance. It will begin to heat with the predened settings.
- Press the MODE button (F) to select one of the following
functions available:
l
Ventilation
In this operating mode only the fan operates, so the ap-
pliance does not heat the room.
l
Anti-freeze
In this operating mode the appliance keeps the room at
a temperature of 7°C to prevent freezing temperatures.
l
Heating 1 and Heating 2
In this operating mode you can set the desired tempera-
ture by pressing the + and - adjustment buttons (B).
- Heating 1 (minimum power level):
The appliance operates at the minimum power, reduc-
ing noise and energy consumption to the minimum.
- Heating 2 (maximum power level):
The appliance operates at the maximum power for rapid
heating of the room.
- To turn o the appliance press button ON/STAND-BY (A).
The display could show the count down for about 6 seconds. To completely turn o the appliance, remove the
plug from the socket.
Please note: The display can show the temperature in
both °C and °F. To change the temperature scale, press and
hold the + key for few seconds, then release.
ECO PLUS function
In this operating mode the appliance will automatically set
the power level to guarantee the best comfort reducing the
energy consumption.
The maximum temperature setting is 26 °C. To activate this
function, press the ECO PLUS button (D).
Oscillation button
If you want the appliance to distribute the airow over a larger area, press the oscillation button (C) . The appliance
will then oscillate right and left. To stop the oscillation in the
desired position, just press oscillation button (C) again.
24HOUR DIGITAL TIMER
This function can be activated from any operating mode.
Delayed switch-on: with the appliance in the STAND-BY
position, press the timer button (E) .
The display shows the symbol and the time remaining
before switch-on. To set the timer, use the + and - adjustment buttons (B), then wait a few seconds for the programming to be set. The display returns to show for stand-by
and the symbol to indicate you have set the timer.
When the programmed time has been reached, the appliance
turns on with the same settings it had during the previous
operation.
Delayed shut-o: With the appliance on, press the timer
button (E) .
The display shows the symbol and the time remaining
before shut-o. To set the timer, use the + and – adjustment
buttons (B), then wait a few seconds for the programming to
be set. The display returns to show the current settings and
the symbol to indicate you have set the timer.
4
Page 6
When the programmed time as been reached the appliance
shuts o automatically. If you want to go back to operation
without the timer, press the timer button (E) twice.
The timer symbol disappears from the display.
Using the remote control (certain models only)
The remote control functions correspond to those on the control panel. See the section “Operation and Use" on the previous page for a description of the functions.
Inserting or replacing the batteries
- The remote control is
provided with a lithium
battery CR2032. To let
the appliance function,
remove the battery cover strip, by pulling it.
- To replace the batteries,
remove the battery cover by rotating it. Replace
the battery paying attention to respect the right polarity as shown in gure 1.
- Replace the cover rotating it towards the position .
- Old batteries must be removed and disposed o in accordance with current legislation as they are harmful to
the environment.
Fig. 1
ter, remove the grille by pulling outward. Blow it lightly,
then replace it into the appliance.
TECHNICAL CHARACTERISTICS
Supply voltage See rating plate
Absorbed power “
Important!
- WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN.
- Swallowing may lead to serious injury in as little as 2
hours or death, due to chemical burns and potential
perforation of the oesophagus.
- Examine devices and make sure the battery compartment is correctly secured. Do not use if compartment is
not secure.
- Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.
MAINTENANCE
- Before carrying out any maintenance, always unplug
from the mains socket.
- During the season when the appliance is in use, clean
the air intake and outlet grilles regularly using a vacuum
cleaner.
- Never use abrasive powders or solvents to clean the appliance.
- The dust lter which retains impurities in the air, It is
integrated in the removable back cover. To clean the l-
5
Page 7
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
PF display and emits a beep
Product doesn’t turn on Check that the plug is connected to the
Temperature sensor is not working
properly
outlet
Please contact Customer Service
Plug in
Auto-start is on
Room temperature reaches the set
temperature
The appliance goes o unexpectedly Check that the plug is connected to the
outlet
The set temperature has been reached
or the time set on the timer has elapsed
A green dot is ashing and unit is o The tip-over switch has been activated Make sure the appliance is standing
The display shows "Ht" blinking
The internal temperature is too high.
The air intake or outlet grille is
obstructed
Wait till time elapsed or press the button (E) twice to cancel the auto-start
and push the button (A)
Use the “+” button to increase the set
temperature
Plug in
upright on a at surface.
ance doesn’t work please contact Customer Service
Check the appliance is correctly
positioned respecting the minum
distances from the wall, or objects, as
indicated on the instruction manual,
if not, position the appliance correctly
Remove the obstruction
Disconnect the plug from the outlet
and let the appliance cool down. After
few minutes plug the appliance again.
If the appliance doesn't work
contact Customer Service
If the appli-
please
6
Loading...