DeLonghi DD User Manual

instructions
DEHUMIDIFIER
DD Series
Please retain these instructions for future reference
5714810461/04.11
Description of Appliance
7
2
DEHUMIDIFIER DD Series
DESCRIPTION/ACCESSORIES
1. Control panel
2. Water level viewing window
3. Condensate collection tank
4. Handles
5. Air intake grille
6. Dust filter
7. Air outlet grille
8. Drain hose to be used at the back of the unit
9. Pump tube to be used at the front of the unit
10. Connector for PUMP draining (first remove stopper)
11. Wheels
4
1
4
5
6
2
3
11
8
9
10
3
Thank you for choosing this De’Longhi dehumidifier. To get the best results from your new dehumidifier, read these instructions carefully and retain for future reference. This is the only way to ensure optimum results and maximum safety.
Safety Warnings
This is an electrical appliance, it is therefore important to respect the following safety warnings:
Do not touch the appliance with wet hands.
Do not touch the plug with wet hands.
The appliance is designed and produced for domestic use only. It is not suitable for use in: staff kitchens in shops, offices and other workplaces, farm houses, hotels, motels or other holi­day accommodation, guest houses.
Make sure the outlet used is always accessible, enabling you to unplug the appliance when necessary.
Always unplug the appliance using the plug itself. Never pull the cable as it might be damaged.
To disconnect the appliance completely from the electricity supply, you must unplug it from the outlet.
If the appliance malfunctions, do not attempt to repair it yourself. Turn the appliance off, unplug from the outlet soc­ket and contact a Customer Experience - See enclosed gua­rantee leaflet.
Do not move the appliance by pulling the power cable.
It is dangerous to modify or alter the characteristics of the appliance in any way.
If the power cable is damaged, it must be replaced by the manufacturer or an authorized technical service center in order to avoid all risk.
Do not use extension cords.
The appliance must be installed in accordance with the rules on household appliances in force in the country concerned.
This appliance is not intended for use for water damage restoration of commercial/household properties.
The appliance must be connected to a properly grounded outlet. Have your electrical circuit checked by a qualified electrician.
Keep packaging materials (plastic bags, polystyrene foam) out of reach of children.
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabili­ties, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Always supervise children. Make sure they do not play with the appliance.
DEHUMIDIFIER DD Series
4
Do not install the appliance in rooms containing gas, oil or
DEHUMIDIFIER DD Series
sulphur. Do not install near sources of heat.
Do not use the appliance on sloping surfaces.
Keep the appliance at least 2 ft (61cm) away from flammable substances (alcohol etc) or pressurised containers (e.g. aerosol cans).
Do not rest heavy or hot objects on top of the appliance.
Always transport the appliance upright, NOT on its side. Remember to drain the condensate tank before moving the appliance. If the appliance was transported on its side, you must wait at least 6 hours before using it (24 hrs is recommended).
The materials used for packaging can be recycled. You are therefore recommended to dispose of them in special differentiated waste collection containers.
Do not use the appliance outdoors.
Do not use the appliance in laundry rooms.
This appliance conforms to the Directive 2004/108/EC relative to electromagnetic compatibility.
ENVIRONMENTAL INFORMATION: This unit contains fluorinated greenhouse gases covered by the Kyoto Protocol. Avoid perforating the refrigerant circuit of the appliance. Maintenance and disposal must be carried out by qualified person­nel only (R410A, GWP=1975).
5
SOME NOTIONS ON HUMIDITY
Air always contains a certain amount of water in the form of vapour. This determines the level of humidity in an atmosphere. The capacity of the air to hold water vapour increases with temperature. This is why in our homes, as soon as the temperature decreases, the vapour contained in the air condenses, as is evident on the colder surfaces in the room, such as the windows, walls etc. The purpose of a dehumidifier is to remove the excess moisture from the air, avoiding the damage caused by condensation. Experts have established that the optimum environmental conditions for our well being and for the home are obtained between 40% and 60% relative humidity. Lower relative humidity can be achieved with higher room temperatures. For lower room temperatures the achievable relative humidity will be on the higher side, closer to 60%. Therefore, with lower room tempera­tures, you are recommended to heat the room even minimally. This considerably increases the dehumidifying power of the appliance. With heating, the condensation formed by the water vapour on windows and other cold surfaces evaporates into the air to be collected by the dehumidifier.
Problems and repairs
In the event of problems, first try and resolve them by reading the information given in the "Troubleshooting" section on page 11. If the appliance requires repair, always contact a Customer Experience - see enclosed guarantee. Always insist on original spare parts. Repairs carried out by unauthorized personnel may be dangerous and invalidate the guarantee.
Appropriate use
The appliance is designed and produced for domestic use only. Use this appliance only as described in this instruction manual. As with all electrical equipment, the instructions aim to cover as many eventualities as possible. However, caution and common sense should be applied when operating and installing this appliance.
Instructions
Read these instructions carefully before installing and/or using the appliance.
Keep these instructions. If the appliance is transferred to other owners, they should also be given these instructions.
Failure to respect the instructions may result in injury or damage to the appliance. The manufacturer is not liable for damage deriving from failure to follow these instructions.
DEHUMIDIFIER DD Series
6
INSTALLATION
Position the appliance in the room to be dehumidified. A free space of at least 2 ft (61 cm) must be left at the front of the dehumidifier, so as not to block the air outlet. For efficient ventilation a space of about 2-4 in (5-10 cm) should be left at the back of the appliance. The condensate can be drained in one of the following ways:
A) Draining into the tank
The condensate can be drained directly into the tank. The tank can be easily removed (fig.1). When the tank is full, remove (fig.1) and empty it into a sink. When finished, replace it properly. NOTE: The tank must be positioned properly for the unit to function. If you hear the intermittent sound of the beep, it means the tank is not in the proper position.
B) Continuous external draining
If the appliance is to be operated for long periods but you are unable to empty the tank regularly, you are recommended to use continuous draining.
1) Remove the continuous drain cap 1 by turning it counterclock­wise then remove the rubber stopper from the spout 2 (fig. 2).
2) Insert the drain cap 1 in the condensate drain hose (8) till the end (fig. 3) then screw the cap into the spout. (fig. 4).
3) Make sure the end of the hose is no higher than the spout (Fig. 3) or water could remain in the tank. Make sure there are no kinks in the hose (Fig. 5).
Keep the rubber stopper to close the spout.
C) Continuous draining using the pump (only on pump
models)
The patented heavy-duty pump system allows water removal of up to 13 ft (4m) in height. If you want the water to flow directly to a drain, connect the condensation discharge tube supplied (9) to the connection pipe. located on the lower front part of the unit unit (you will first need to remove the stopper labeled PUMP) (fig. 6). Select the dehumidifying function and press the PUMP button.
Note: With the condensation discharge hose missing and the pump switched ON, the display will show the symbol PUMP blinking. To eliminate this problem:
Check the hose is correctly positioned;
Switch the appliance off by pressing the “ON/STAND-
BY “ button .
Disconnect and reconnect the plug.
1
2
Fig.1
Fig.2
Fig.3
Fig.4
DEHUMIDIFIER DD Series
1 PUSH
2
Fig.5
Fig.6
NO
NO
YES
7
DESCRIPTION OF BUTTONS 1 ON/Standby button
ON/Standby button
2 "Fan" button
Press this button to select the Fan Speed (MIN or MAX).
3 Room Temperature Button
Temporarily displays the temperature measured in the room by the appliance. If you press the button once you will see the room temperature in F for a few seconds, then in C for a few seconds, then the display will return to the current level of humidity in the room. If you press the button multiple times, it will cycle through these displays faster. Note: Temperatures displayed are indicative only.
4 Humidity increase/decrease buttons
These buttons are used to adjust the desired humidity level, with 5% increments; they are also used to set the timer. From 0 -10 the hours increase by 30 min. and from 10-24 the hours increase by 1 hour increments.
5 Pump button
When you press the “Pump button” the display will show “PUMP”. If the display shows “PUMP” blinking, it means that the pump is not operating correctly.
Display
Increase
humidity
level
button
PUMP
button
TIMER button
Fan speed
button
Room temperature button °F/°C
Decrease humidity
level
button
ON/STAND-BY
CONTROL PANEL
DEHUMIDIFIER DD Series
6 Timer button
If you press the TIMER button the display will show the hours after which you want the appliance to switch OFF or ON. Once the timer is set the user can no longer adjust the room humi­dity.
Display
Meaning of the codes or symbols which may be displayed:
-- -- Indicates that the appliance is in standby mode.
Tank warning symbol
If the water tank is full, improperly positioned or missing, the tank warning light will start blinking. An alarm will sound until the tank is either emptied or correctly positioned into place.
Defrosting indicator symbol
With an ambient temperature of less than 59°F (15°C) the appliance performs defrosting cycles. While the appliance is defro­sting, the defrosting symbol comes on and remains on until defrosting is completed. This symbol will also be displayed if the unit is swit­ched on immediately after being turned off. The unit requires 3 minutes before it can function again.
MODE SELECTION
1) Plug the appliance into a an outlet.
2) The display will show “-- --“ to indicate that the appliance is in stand-by and ready for use. If the display shows “
it’s necessary to empty the tank or the tank is incorrectly positioned
3) Press the ON/Stand-by button.
Dehumidifying Mode
The display will show on the left side the room humidity level
(ex.:
63) and on the right side the display will show the
degree of humidity you want to reach (ex.:
58 ).
Press the “+” or “-“ button to set the desired humidity level (30% means a dry environment, 80% a humid environment). Press the “ ” to select the fan speed (MIN/MAX). If you select MAX, the appliance will operate to the maximum speed. If you select MIN, the appliance will operate to the minimum speed and the noise levels will be reduced. Press button “ ” to display the Temperature on the LCD display. On the left side the display will show first the °F and then the temperature in °C. After a few seconds, the display will automatically show the
8
DEHUMIDIFIER DD Series
humidity level. When the appliance reaches the humidity set point the appliance will automatically stop working but the fan will work at the minimum speed. As soon as the humidity increases above the set point, the appliance will automatically resume dehumidification operation.
Continuous Dehumidifying Function
In order to operate the continuous dehumidifying function press button “-” untill the display shows “--”.
With this function the appliance will operate continuously.
TIMER How to program the delayed start function: From the OFF Position
1) With the unit in the stand-by position, press the but­ton. On the right side the display will show and the number of hours after which the appliance will start opera­ting.
2) Use the + and - button to set the desired hours. Wait few seconds to set the appliance. The symbol and the remaining time will be displayed.
3) When the selected time is reached, the appliance will start working.
How to Program the delayed stop function: From the ON Position
1) With the unit in the ON position, press the button. On the right side the display will show and the num­ber of hours after which the appliance will stop operating.
2) Use the + and - button to set the desired hours. Wait a few seconds to set the appliance. The symbol and the remaining time will be displayed.
3) When the selected time is reached, the appliance will stop working.
How to modify or disactivate the timer
If you wish to modify the set value, press the timer button once and then buttons + and -. If you wish to disactivate the timer press the timer button twice.
Note: When switching the appliance on or when the electri­city is restored, the appliance will start working on previously
selected mode.
9
DEHUMIDIFIER DD Series
10
CLEANING AND MAINTENANCE
Always unplug the appliance from the power outlet before performing any cleaning or maintenance operations. For safety reasons, never wash the dehumidifier using a jet of water.
Cleaning the cabinet
Clean the appliance using a damp cloth then dry with a dry cloth.
Do not use petrol, alcohol or solvents to clean the applian­ce.
Do not spray liquid insecticide or similar products as they may deform the plastic.
Cleaning the air filter
If the filter is dirty, air circulation is compromised and the effi­ciency of the dehumidifying and air purifying functions decrea­ses. It is therefore good practice to clean the filter at regular inter­vals. The frequency depends on the duration and conditions of operation. If the unit is used constantly or systematically, you are recommended to clean the filter once a week. To remove the filter, pull it down as shown in figure 7.
If the appliance is not used for long periods
After unplugging the appliance from the power outlet, empty the tank.
Clean and reposition the filter.
Cover the appliance with a plastic bag to protect it from dust.
TECHNICAL SPECIFICATIONS
Power supply voltage See rating plate Absorbed power “ Maximum power input “ Freeze protection device Yes Hygrometer Yes Fan speeds 2 Air filter Yes
Operating limits: temperature 41°F - 89.6°F (5°C - 32°C) relative humidity 30-90%
Fig.7
DEHUMIDIFIER DD Series
11
TROUBLESHOOTING
Check the following points before contacting Customer Experience.
PROBLEMS CAUSE SOLUTION
The filter is blocked.
The temperature or humidity in the room are too low.
The room is too big for the dehumidifying power of the appliance.
Too many sources of humidity in the room (pots of boiling water, etc.).
The humidy set point is too high.
Clean the filter.
In certain conditions, it is normal for the appliance not to dehumidify (in certain cases, it is recommen­ded to heat the environment).
Decrease the humidity set point.
The appliance is ope­rating in dehumidifying mode, but the humidity does not decrease.
The safety device has tripped.
Wait for 3 minutes to pass.
The appliance does not work for 3 minutes after start-up.
is displayed
is displayed
E2”/”E3”is displayed
Symbol “PUMP” is displayed
The tank is missing.
The tank is full.
The tank is incorrectly positioned.
The temperature in the room is very low.
One of the sensors on the appliance is faulty.
The condensation dis­charge pump is missing.
Replace the tank.
Empty the tank.
Position the tank correctly.
Increase room temperature.
Contact Customer Experience - See enclosed guarantee.
Check the hose is correctly positioned.
Disconnect and
reconnect the plug.
DEHUMIDIFIER DD Series
Green and Yellow to
Earth
Blue to
Neutral
13 amp Fuse
Brown to Live
Cord Clamp
ELECTRICAL REQUIREMENTS
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, follow­ing the procedure outlined below. Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of, (having removed the fuse) and not left where children might find it and plug it into a supply socket - with the obvious consequent danger. If the plug is a moulded-on type the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover. N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use. important: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size. Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted. This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference. This appliance MUST be Earthed
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
Loading...