Dell Vostro 5401 Service Manual

Vostro 5401

Service Manual

Regulatory Model: P130G

Regulatory Type: P130G001

July 2020

Rev. A01

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

Contents

Chapter 1: Working on your computer...............................................................................................	7
Safety instructions.................................................................................................................................................................	7
Before working inside your computer............................................................................................................................	7
Safety precautions...........................................................................................................................................................	8
Electrostatic discharge—ESD protection....................................................................................................................	8
ESD field service kit ........................................................................................................................................................	9
After working inside your computer..............................................................................................................................	9
Chapter 2: Major components of your system...................................................................................	11
Chapter 3: Disassembly and reassembly..........................................................................................	13
Recommended tools............................................................................................................................................................	13
Screw list...............................................................................................................................................................................	13
Base cover............................................................................................................................................................................	15
Removing the base cover..............................................................................................................................................	15
Installing the base cover................................................................................................................................................	16
Battery...................................................................................................................................................................................	18
Lithium-ion battery precautions...................................................................................................................................	18
Removing the 3-cell battery - UMA/discrete.............................................................................................................	19
Installing the 3-cell battery - UMA/discrete..............................................................................................................	20
Removing the 4-cell battery - UMA/discrete.............................................................................................................	21
Installing the 4-cell battery - UMA/discrete...............................................................................................................	21
WLAN card...........................................................................................................................................................................	22
Removing the WLAN card - UMA...............................................................................................................................	22
Installing the WLAN card - UMA.................................................................................................................................	23
Removing the WLAN card - discrete..........................................................................................................................	24
Installing the WLAN card - discrete............................................................................................................................	25
Memory modules.................................................................................................................................................................	26
Removing the memory modules - UMA.....................................................................................................................	26
Installing the memory modules - UMA........................................................................................................................	27
Removing the memory modules - discrete................................................................................................................	28
Installing the memory modules - discrete...................................................................................................................	29
Solid-state drive...................................................................................................................................................................	31
Removing the M.2 2280 solid-state drive - UMA......................................................................................................	31
Installing the M.2 2280 solid-state drive - UMA........................................................................................................	31
Removing the M.2 2230 solid-state drive - UMA.....................................................................................................	32
Installing the M.2 2230 solid-state drive - UMA........................................................................................................	33
Removing the M.2 2280 solid-state drive - SSD-1 - discrete..................................................................................	34
Installing the M.2 2280 solid-state drive - SSD-1 - discrete....................................................................................	34
Removing the M.2 2230 solid-state drive - SSD-1 - discrete..................................................................................	35
Installing the M.2 2230 solid-state drive - SSD-1 - discrete....................................................................................	36
Replacing the SSD-1 support bracket.........................................................................................................................	37
Removing the M.2 2280 solid-state drive - SSD-2 - discrete.................................................................................	38
Installing the M.2 2280 solid-state drive - SSD-2 - discrete...................................................................................	39

Contents 3

Speakers...............................................................................................................................................................................	40
Removing the speakers (in 3-cell battery configuration).........................................................................................	40
Installing the speakers (in 3-cell battery configuration)............................................................................................	41
Removing the speakers (in 4-cell battery configuration).........................................................................................	42
Installing the speakers (in 4-cell battery configuration)...........................................................................................	43
System fan...........................................................................................................................................................................	45
Removing the system fan - UMA................................................................................................................................	45
Installing the system fan - UMA..................................................................................................................................	46
Removing the system fan - discrete...........................................................................................................................	47
Installing the system fan - discrete.............................................................................................................................	48
Heat sink...............................................................................................................................................................................	49
Removing the heat sink - UMA....................................................................................................................................	49
Installing the heat sink - UMA......................................................................................................................................	49
Removing the heat sink - discrete..............................................................................................................................	50
Installing the heat sink - discrete..................................................................................................................................	51
Coin-cell battery..................................................................................................................................................................	52
Removing the coin-cell battery - UMA.......................................................................................................................	52
Installing the coin-cell battery - UMA.........................................................................................................................	53
Removing the coin-cell battery - discrete..................................................................................................................	54
Installing the coin-cell battery - discrete....................................................................................................................	54
I/O board..............................................................................................................................................................................	55
Removing the I/O board - UMA..................................................................................................................................	55
Installing the I/O board - UMA....................................................................................................................................	56
Removing the I/O board - discrete.............................................................................................................................	58
Installing the I/O board - discrete...............................................................................................................................	59
Power button with fingerprint reader (optional).............................................................................................................	60
Removing the power button and optional fingerprint reader - UMA.....................................................................	60
Installing the power button with finger reader - UMA..............................................................................................	61
Removing the power button and optional fingerprint reader - discrete.................................................................	62
Installing the power button with finger reader - discrete ........................................................................................	62
DC-in port.............................................................................................................................................................................	63
Removing the DC-in port - UMA.................................................................................................................................	63
Installing the DC-in port - UMA...................................................................................................................................	64
Removing the DC-in port - discrete............................................................................................................................	65
Installing the DC-in port - discrete..............................................................................................................................	66
Touchpad..............................................................................................................................................................................	67
Removing the touchpad - UMA...................................................................................................................................	67
Installing the touchpad - UMA.....................................................................................................................................	68
Removing the touchpad - discrete..............................................................................................................................	70
Installing the touchpad - discrete.................................................................................................................................	71
Display assembly..................................................................................................................................................................	72
Removing the display assembly - UMA.......................................................................................................................	72
Installing the display assembly - UMA.........................................................................................................................	74
Removing the display assembly - discrete..................................................................................................................	75
Installing the display assembly - discrete....................................................................................................................	78
System board.......................................................................................................................................................................	80
Removing the system board - UMA...........................................................................................................................	80
Installing the system board - UMA..............................................................................................................................	82
Removing the system board - discrete......................................................................................................................	85
Installing the system board - discrete.........................................................................................................................	87

4 Contents

Palm-rest and keyboard assembly....................................................................................................................................	90
Removing the palm-rest and keyboard assembly - UMA.........................................................................................	90
Installing the palm-rest and keyboard assembly - UMA............................................................................................	91
Removing the palm-rest and keyboard assembly - discrete....................................................................................	92
Installing the palm-rest and keyboard assembly - discrete......................................................................................	93
Chapter 4: Software......................................................................................................................	95
Downloading Windows drivers...........................................................................................................................................	95
Chapter 5: System setup...............................................................................................................	96
Boot menu............................................................................................................................................................................	96
Navigation keys....................................................................................................................................................................	96
Boot Sequence.....................................................................................................................................................................	97
BIOS setup............................................................................................................................................................................	97
Overview.........................................................................................................................................................................	97
Boot configuration.........................................................................................................................................................	98
Integrated Devices........................................................................................................................................................	99
Storage..........................................................................................................................................................................	100
Display...........................................................................................................................................................................	100
Connection options......................................................................................................................................................	100
Power management.....................................................................................................................................................	101
Security.........................................................................................................................................................................	102
Password.......................................................................................................................................................................	103
Update and Recovery..................................................................................................................................................	104
System management...................................................................................................................................................	105
Keyboard.......................................................................................................................................................................	106
Pre-boot behavior........................................................................................................................................................	107
Virtualization support...................................................................................................................................................	107
Performance.................................................................................................................................................................	108
System logs...................................................................................................................................................................	108
Updating the BIOS in Windows .......................................................................................................................................	109
Updating BIOS on systems with BitLocker enabled................................................................................................	109
Updating the Dell BIOS in Linux and Ubuntu environments....................................................................................	110
Flashing the BIOS from the F12 One-Time boot menu............................................................................................	110
System and setup password.............................................................................................................................................	113
Assigning a system setup password...........................................................................................................................	113
Deleting or changing an existing system setup password.......................................................................................	113
Chapter 6: Troubleshooting..........................................................................................................	115
Built-in self-test (BIST)......................................................................................................................................................	115
System board built-in self-test (M-BIST)........................................................................................................................	116
Display panel power rail built-in self-test (L-BIST)...................................................................................................	116
Display panel power rail built-in self-test (L-BIST).........................................................................................................	117
Display panel built-in self-test (LCD-BIST).....................................................................................................................	117
Outcome..............................................................................................................................................................................	118
SupportAssist diagnostics..................................................................................................................................................	118
Running the SupportAssist diagnostics...........................................................................................................................	118
System diagnostic lights....................................................................................................................................................	118
Recovering the operating system....................................................................................................................................	120

Contents 5

Flashing the BIOS...............................................................................................................................................................	120
Flashing BIOS (USB key)..................................................................................................................................................	120
Backup media and recovery options................................................................................................................................	120
WiFi power cycle.................................................................................................................................................................	121
Releasing Ethernet (RJ-45) cable....................................................................................................................................	121
Chapter 7: Getting help................................................................................................................	122
Contacting Dell...................................................................................................................................................................	122

6 Contents

Working on your computer

Topics:

•Safety instructions

Safety instructions

Prerequisites

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:

•You have read the safety information that shipped with your computer.

•A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.

About this task

NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the computer, replace all covers, panels, and screws before connecting to the power source.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface at the same time as touching a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Before working inside your computer

About this task

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

Steps

1.Ensure that you follow the Safety Instruction.

2.Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

3.Turn off your computer.

4.Disconnect all network cables from the computer.

Working on your computer

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

5.Disconnect your computer and all attached devices from their electrical outlets.

6.Press and hold the power button while the computer is unplugged to ground the system board.

NOTE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface at the same time as touching a connector on the back of the computer.

Safety precautions

The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.

Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or reassembly:

•Turn off the system and all attached peripherals.

•Disconnect the system and all attached peripherals from AC power.

•Disconnect all network cables, telephone, and telecommunications lines from the system.

•Use an ESD field service kit when working inside any notebook to avoid electrostatic discharge (ESD) damage.

•After removing any system component, carefully place the removed component on an anti-static mat.

•Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.

Standby power

Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and suspended into a sleep mode and has other advanced power management features.

Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board. Remove the battery from notebooks.

Bonding

Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare metal and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and ensure that you remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

•Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.

•Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.

Perform the following steps to prevent ESD damage:

•Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased sensitivity to ESD damage.

8 Working on your computer

•Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

•When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static electricity from your body.

•Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: antistatic mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

•Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an antistatic mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESDsensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

•Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at least once per week.

•ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.

•Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are insulators and often highly charged.

•Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically handling any hardware components

•ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

•Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

After working inside your computer

About this task

After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your computer.

Working on your computer

Steps

1.Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.

2.Connect your computer and all attached devices to their electrical outlets.

3.Turn on your computer.

4.If required, verify that the computer works correctly by running SupportAssist diagnostics.

10 Working on your computer

Major components of your system

1.Base cover

2.Battery

3.DC-in port

4.Heat sink

5.Memory module

6.Solid-state drive shield

7.M.2 2230 SSD

8.Speaker

9.System board

10.Touchpad

11.Palm-rest and keyboard assembly

12.Display assembly

13.Power button with fingerprint reader

14.Coin-cell battery

15.I/O board

16.System fan

17.WLAN card

Major components of your system

18. M.2 2280 SSD

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for purchase options.

12 Major components of your system

Disassembly and reassembly

Topics:

•Recommended tools

•Screw list

•Base cover

•Battery

•WLAN card

•Memory modules

•Solid-state drive

•Speakers

•System fan

•Heat sink

•Coin-cell battery

•I/O board

•Power button with fingerprint reader (optional)

•DC-in port

•Touchpad

•Display assembly

•System board

•Palm-rest and keyboard assembly

Recommended tools

The procedures in this document may require the following tools:

•Phillips #0 screwdriver

•Phillips #1 screwdriver

•Plastic scribe (recommended for field technicians)

NOTE: The #0 screw driver is for screws 0-1, and the #1 screw driver is for screws 2-4.

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when the component is replaced.

NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list

Component	Screw type	Quantity	Screw image


Base cover	M2x8.8 - captive	2
	M2x4	5

Disassembly and reassembly

Table 1. Screw list (continued)

Component	Screw type	Quantity	Screw image



Battery	M2x3	4

WLAN	M2x3	1

Solid-state drive -1	M2x3	1

Solid-state drive - 2	M2x3	2

Solid-state drive -2 support	M1.6x2	1
bracket

System fan	M2x2	2

Heat sink - UMA	M2x5.35 - captive	4

Heat sink - discrete	M2x5.35 - captive	7

Hinge screws	M2.5x4	3
	M2x3	1

I/O board	M2x3	3

Power button with fingerprint	M2x2.5	2
reader

DC-in port	M2x3	1

Touchpad	1.6x2	3
	M2x2	2

Display assembly	M2.5x4	3
	M2x3	1

System board	M2x3	2

14 Disassembly and reassembly

Base cover

Removing the base cover

Prerequisites

Follow the procedure in before working inside your computer.

About this task

The figure indicates the location of the base cover and provides a visual representation of the removal procedure.

Disassembly and reassembly

Steps

1.Remove the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

2.Loosen the two captive screws (M2x8.8) that secure the base cover to the palm-rest and keyboard assembly.

3.Pry open the base cover starting from the recess at the hinge area and work your way around and follow the "guidance line" indicated in the image to remove the base cover.

4.Lift the base cover off the palm-rest and keyboard assembly.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the base cover and provides a visual representation of the installation procedure.

16 Disassembly and reassembly

Disassembly and reassembly

Steps

1.Place the base cover on the palm-rest and keyboard assembly, and snap the base cover into place.

2.Tighten the two captive screws (M2x8.8) that secure the base cover to the palm-rest and keyboard assembly.

3.Replace the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

Next steps

Follow the procedure in after working inside your computer.

Battery

Lithium-ion battery precautions

CAUTION:

•Exercise caution when handling Lithium-ion batteries.

•Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and operate the computer solely on battery power—the battery is fully discharged when the computer no longer turns on when the power button is pressed.

•Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

•Do not expose the battery to high temperatures, or disassemble battery packs and cells.

•Do not apply pressure to the surface of the battery.

18 Disassembly and reassembly

•Do not bend the battery.

•Do not use tools of any kind to pry on or against the battery.

•Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or damage to the battery and other system components.

•If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See www.dell.com/contactdell.

•Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

Removing the 3-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

About this task

The figure indicates the location of the 3-cell battery in an UMA configuration and provides a visual representation of the removal procedure.

Steps

1.Disconnect the battery cable from the system board.

2.Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3.Lift the battery off the palm-rest and keyboard assembly.

Disassembly and reassembly

Installing the 3-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the 3-cell battery in an UMA configuration and provides a visual representation of the installation procedure.

Steps

1.Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the palmrest and keyboard assembly.

2.Install the four screws (M2x3) that secure the battery to the system board and palm-rest and keyboard assembly.

3.Connect the battery cable to the system board.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

20 Disassembly and reassembly

Removing the 4-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

About this task

The figure indicates the location of the battery in a discrete configuration and provides a visual representation of the removal procedure.

Steps

1.Disconnect the battery cable from the system board.

2.Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3.Lift the battery off the palm-rest and keyboard assembly.

Installing the 4-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

If you are replacing a component, remove the existing component before performing the installation procedure.

Disassembly and reassembly

About this task

The figure indicates the location of the battery in a discrete configuration and provides a visual representation of the installation procedure.

Steps

1.Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the palmrest and keyboard assembly.

2.Install the four screws (M2x3) that secure the battery to the system board and palm-rest and keyboard assembly.

3.Connect the battery cable to the system board.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

WLAN card

Removing the WLAN card - UMA

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

3.Remove the battery.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.

22 Disassembly and reassembly

Steps

1.Remove the single screw (M2x3) that secures the WLAN card bracket to the WLAN card.

2.Remove the WLAN card bracket from the WLAN card.

3.Disconnect the antenna cables from the WLAN card.

4.Slide and remove the WLAN card from the WLAN card slot.

Installing the WLAN card - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the installation procedure.

Disassembly and reassembly

Steps

1.Align the notch on the WLAN card with the tab on the WLAN card slot and insert the WLAN card at an angle into the WLAN card slot.

2.Connect the antenna cables to the WLAN card.

3.Align and place the WLAN card bracket on the WLAN card.

4.Replace the screw (M2x3) to secure the WLAN card bracket to the WLAN card.

Next steps

1.Install the battery.

2.Install the base cover.

3.Follow the procedure in after working inside your computer.

Removing the WLAN card - discrete

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

3.Remove the battery.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.

24 Disassembly and reassembly

Steps

1.Remove the single screw (M2x3) that secures the WLAN card bracket to the WLAN card.

2.Remove the WLAN card bracket from the WLAN card.

3.Disconnect the antenna cables from the WLAN card.

4.Slide and remove the WLAN card from the WLAN card slot.

Installing the WLAN card - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the installation procedure.

Disassembly and reassembly

Steps

1.Align the notch on the WLAN card with the tab on the WLAN card slot and insert the WLAN card at an angle into the WLAN card slot.

2.Connect the antenna cables to the WLAN card.

3.Align and place the WLAN card bracket on the WLAN card.

4.Replace the screw (M2x3) to secure the WLAN card bracket to the WLAN card.

Next steps

1.Install the battery.

2.Install the base cover.

3.Follow the procedure in after working inside your computer.

Memory modules

Removing the memory modules - UMA

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

3.Disconnect the battery.

26 Disassembly and reassembly

About this task

The figure indicates the location of the memory module and provides a visual representation of the removal procedure.

Steps

1.Lift the mylar covering the memory module.

2.Using your finger tips gently pry the retention clips away from the memory module until the memory module pops up.

3.Slide and remove the memory module off the memory module slot on the system board.

Installing the memory modules - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the memory module and provides a visual representation of the installation procedure.

Disassembly and reassembly

Steps

1.Lift the mylar, and align the notch on the memory module with the tab on the memory-module slot.

2.Slide the memory module firmly into the slot at an angle.

3.Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

Next steps

1.Connect the battery.

2.Install the base cover.

3.Follow the procedure in after working inside your computer.

Removing the memory modules - discrete

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

3.Disconnect the battery.

28 Disassembly and reassembly

About this task

The figure indicates the location of the memory module and provides a visual representation of the removal procedure.

Steps

1.Lift the mylar covering the memory module.

2.Using your finger tips gently pry the retention clips away from the memory module until the memory module pops up.

3.Slide and remove the memory module off the memory module slot on the system board.

Installing the memory modules - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the memory module and provides a visual representation of the installation procedure.

Disassembly and reassembly

Steps

1.Lift the mylar, and align the notch on the memory module with the tab on the memory-module slot.

2.Slide the memory module firmly into the slot at an angle.

3.Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

Next steps

1.Connect the battery.

2.Install the base cover.

3.Follow the procedure in after working inside your computer.

30 Disassembly and reassembly

+ 92 hidden pages