Dell 5570 Service Manual

Precision 5570

Service Manual

Par t N umb er: P9 1F Reg ula tor y T ype : P 91F 003 Apr il 202 2 Rev . A 01

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

© 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

Chapter 1: Working inside your computer...................................................................................... 5

Before working inside your computer.............................................................................................................................5

Safety instructions.............................................................................................................................................................. 5

Electrostatic discharge—ESD protection..................................................................................................................... 6

ESD field service kit ...........................................................................................................................................................6

Transporting sensitive components................................................................................................................................ 7

After working inside your computer................................................................................................................................7

Chapter 2: Removing and installing components........................................................................... 8

Recommended tools........................................................................................................................................................... 8

Screw list............................................................................................................................................................................... 8

Major components of Precision 5570.............................................................................................................................9

Base cover............................................................................................................................................................................11

Removing the base cover........................................................................................................................................... 11

Installing the base cover.............................................................................................................................................14

Battery..................................................................................................................................................................................15

Lithium-ion battery precautions............................................................................................................................... 15

Removing the battery................................................................................................................................................. 16

Installing the battery....................................................................................................................................................17

Memory.................................................................................................................................................................................18

Removing the memory................................................................................................................................................ 18

Installing the memory................................................................................................................................................. 20

Solid-state drive................................................................................................................................................................. 21

Removing the solid-state drive 1.............................................................................................................................. 21

Installing the solid-state drive 1................................................................................................................................22

Removing the solid-state drive 2.............................................................................................................................23

Installing the solid-state drive 2...............................................................................................................................24

Installing the M.2 2230 solid-state drive............................................................................................................... 25

Fans...................................................................................................................................................................................... 26

Removing the left fan.................................................................................................................................................26

Installing the left fan................................................................................................................................................... 27

Removing the right fan.............................................................................................................................................. 28

Installing the right fan................................................................................................................................................ 29

Heat sink..............................................................................................................................................................................30

Removing the heat sink............................................................................................................................................. 30

Installing the heat sink................................................................................................................................................ 31

Speakers.............................................................................................................................................................................. 32

Removing the speakers..............................................................................................................................................32

Installing the speakers................................................................................................................................................ 33

I/O board.............................................................................................................................................................................34

Removing the I/O board............................................................................................................................................ 34

Installing the I/O board.............................................................................................................................................. 35

Display assembly................................................................................................................................................................ 37

Removing the display assembly................................................................................................................................37

Contents 3

Installing the display assembly..................................................................................................................................39

System board..................................................................................................................................................................... 42

Removing the system board..................................................................................................................................... 42

Installing the system board....................................................................................................................................... 45

LED board............................................................................................................................................................................49

Removing the LED board...........................................................................................................................................49

Installing the LED board.............................................................................................................................................50

Palm-rest and keyboard assembly................................................................................................................................. 51

Removing the palm-rest and keyboard assembly.................................................................................................51

Installing the palm-rest and keyboard assembly.................................................................................................. 52

Chapter 3: Drivers and downloads............................................................................................... 54

Chapter 4: System setup............................................................................................................. 55

Entering BIOS setup program........................................................................................................................................ 55

Navigation keys................................................................................................................................................................. 55

Boot Sequence.................................................................................................................................................................. 55

One time boot menu.........................................................................................................................................................56

System setup options.......................................................................................................................................................56

System and setup password.......................................................................................................................................... 65

Assigning a system setup password....................................................................................................................... 66

Deleting or changing an existing system setup password.................................................................................66

Clearing CMOS settings.............................................................................................................................................67

Clearing BIOS (System Setup) and System passwords.....................................................................................67

Updating the BIOS............................................................................................................................................................ 67

Updating the BIOS in Windows................................................................................................................................67

Updating the BIOS using the USB drive in Windows.......................................................................................... 67

Updating the BIOS from the F12 One-Time boot menu.....................................................................................68

Chapter 5: Troubleshooting.........................................................................................................69

Handling swollen Lithium-ion batteries........................................................................................................................ 69

Locate the Service Tag or Express Service Code of your Dell computer ............................................. 69

System diagnostic lights.................................................................................................................................................. 70

SupportAssist diagnostics................................................................................................................................................71

Built-in self-test (BIST).................................................................................................................................................... 71

M-BIST............................................................................................................................................................................71

LCD Built-in Self Test (BIST)................................................................................................................................... 72

Recovering the operating system..................................................................................................................................72

WiFi power cycle................................................................................................................................................................72

Drain residual flea power (perform hard reset)......................................................................................................... 73

Backup media and recovery options............................................................................................................................. 73

Real Time Clock—RTC reset..........................................................................................................................................73

Chapter 6: Getting help and contacting Dell................................................................................ 75

Contents

Working inside your computer

Before working inside your computer

About this task

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Steps

1. Save and close all open files and exit all open applications.

2. Shut down your computer. Click Start > Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down

instructions.

3. Disconnect your computer and all attached devices from their electrical outlets.

4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

CAUTION:

cable from the network device.

To disconnect a network cable, first unplug the cable from your computer and then unplug the

5. Remove any media card and optical disc from your computer, if applicable.

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.

WARNING:

computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/

regulatory_compliance.

WARNING: Disconnect your computer from all power sources before opening the computer cover or panels.

After you finish working inside the computer, replace all covers, panels, and screws before connecting your

computer to an electrical outlet.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.

CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the

pins and the contacts.

CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the

safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.

Before working inside your computer, read the safety information that is shipped with your

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal

surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal

surface to dissipate static electricity which could harm internal components.

CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables

have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable.

Working inside your computer 5

When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting

cables, ensure that the ports and the connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

CAUTION: Exercise caution when handling Lithium-ion batteries in laptops. Swollen batteries should not be used

and should be replaced and disposed properly.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

● Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.

● Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.

Perform the following steps to prevent ESD damage:

● Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased sensitivity to ESD damage.

● Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

● When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static

packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static electricity from your body.

● Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: anti-static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

● Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

● Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never

Working inside your computer

use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at least once per week.

● ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.

● Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are insulators and often highly charged.

Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For

●

example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically handling any hardware components

● ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

● Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

After working inside your computer

About this task

CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.

Steps

1. Replace all screws and ensure that no stray screws remain inside your computer.

2. Connect any external devices, peripherals, or cables you removed before working on your computer.

3. Replace any media cards, discs, or any other parts that you removed before working on your computer.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Working inside your computer

Removing and installing components

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Recommended tools

The procedures in this document may require the following tools:

● Phillips screwdriver #0

● Phillips screwdriver #1

● Torx #5 (T5) screwdriver

● Plastic scribe

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and

then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when the component is replaced.

NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when

replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list

Component Secured to Screw type Quantity Screw image

Base cover Palm-rest and

keyboard assembly

Battery Palm-rest and

keyboard assembly

Battery Palm-rest and

keyboard assembly

Right fan System board and

palm-rest and keyboard assembly

I/O board shield I/O board M2x4 1

Left fan System board and

palm-rest and keyboard assembly

M2x3 8

M2x3 4

M2x4 4

M2x4 1

M2x4 2

Solid-state drive 1 System board M2x2 1

Solid-state drive 2 System board M2x2 1

8 Removing and installing components

Table 1. Screw list (continued)

Component Secured to Screw type Quantity Screw image

Speakers Palm-rest and

keyboard assembly

Graphics card-processor thermal shield cover

Type-C bracket Palm-rest and

Display-assembly cable bracket

Display-assembly cable holder

Left hinge System board and

Right hinge System board and

Wireless-card bracket System board M1.6x3 1

System board Palm-rest and

System board M2x2 2

keyboard assembly

System board M2x2 3

Palm-rest and keyboard assembly

palm-rest and keyboard assembly

keyboard assembly

M2x2 4

M2x4 2

M1.6x3 2

M2.5x5.5 4

M2x4 2

Touchpad Palm-rest and

keyboard assembly

Touchpad Palm-rest and

keyboard assembly

M1.6x2.5 6

M2x1.5 3

Major components of Precision 5570

The following image shows the major components of the Precision 5570.

Removing and installing components

1. Base cover

2. Battery

3. Heat sink

4. Memory module

5. Right fan

6. USB Type-C bracket

7. System board

8. Charger thermal bracket

9. Speaker

10. Display assembly

11. Palm-rest and keyboard assembly

12. Wireless-card bracket

13. I/O-board shield

14. I/O board

15. USB Type-C port bracket

16. I/O-board cable

17. Left fan

18. Display-assembly cable bracket

19. Solid-state drive 2

20. Solid-state drive 2 thermal bracket

21. Solid-state drive 1

22. Solid-state drive 1 thermal bracket

Removing and installing components

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for purchase options.

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in Before working inside your computer.

About this task

The following images indicate the location of the base cover and provide a visual representation of the removal procedure.

Removing and installing components 11

12 Removing and installing components

Steps

1. Remove the eight screws (M2x3) that secure the base cover to the palm-rest and keyboard assembly.

CAUTION:

damage the base cover.

CAUTION: Do not pry open from the top of the computer as this will damage the display FPC.

CAUTION: The base cover is preassembled with the audio-daughter board. The pins at the bottom of the

base cover are fragile. They ground the antennas and audio-daughter board. Place the base cover on a clean

surface to avoid damage to the pins.

Do not pull on or pry the base cover at the side where the hinges are located; doing so may

2. Starting from the bottom-left corner, use a plastic scribe to pry the base cover in the direction of the arrows to release the base cover from the palm-rest and keyboard assembly.

3. Grasp the left side and the right side of the base cover and remove the base cover from the palm-rest and keyboard assembly.

Removing and installing components

CAUTION: Handle with care as the underside of the base cover has pins for grounding the audio board. After

removing the base cover, place it in a location where contact can be avoided.

NOTE: The following steps are applicable only if you want to further remove any other component from your computer.

NOTE: Disconnecting the battery cable, removing the battery, or draining the flea power clears the CMOS and resets

the BIOS settings on your computer.

NOTE: After your computer is reassembled and powered on, it prompts for the Real Time Clock (RTC) reset. When

the RTC reset cycle occurs, the computer restarts several times and then an error message is displayed– "Time of day not set". Enter the BIOS when this error appears and set the date and time on your computer to resume normal functionality.

4. Disconnect the battery cable from the system board.

5. Turn your computer over and press the power button for 15 seconds to drain the flea power.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the base cover and provide a visual representation of the installation procedure.

Removing and installing components

Steps

1. Connect the battery cable to the system board, if applicable.

2. Align the screw holes on the base cover with the screw holes on the palm-rest and keyboard assembly.

3. Starting from the bottom-right corner snap the base cover in. Work your way around to the middle of the base cover and then to the bottom-left corner and snap the base cover into place.

4. Replace the eight screws (M2x3) that secure the base cover to the palm-rest and keyboard assembly.

Next steps

NOTE:

After your computer is reassembled and powered on, it prompts for the Real Time Clock (RTC) reset. When the RTC reset cycle occurs, the computer restarts several times and then an error message is displayed- "Time of day not set". Enter the BIOS when this error appears and set the date and time on your computer to resume normal functionality.

1. Follow the procedure in After working inside your computer.

Battery

Lithium-ion battery precautions

CAUTION:

● Exercise caution when handling Lithium-ion batteries.

Removing and installing components 15

● Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and

operate the computer solely on battery power—the battery is fully discharged when the computer no longer

turns on when the power button is pressed.

● Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

● Do not expose the battery to high temperatures, or disassemble battery packs and cells.

● Do not apply pressure to the surface of the battery.

● Do not bend the battery.

● Do not use tools of any kind to pry on or against the battery.

● Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental

puncture or damage to the battery and other system components.

● If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,

bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical

support for assistance. See www.dell.com/contactdell.

● Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

● Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to

handle and replace swollen Lithium-ion batteries, see Handling swollen Lithium-ion batteries.

Removing the battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

NOTE:

Disconnecting the battery cable, removing the battery, or draining the flea power clears the CMOS and resets

the BIOS settings on your computer.

About this task

To disconnect the battery cable, release the pull tab located under the battery cable and use it to disconnect the battery cable.

The following image indicates the location of the battery and provides a visual representation of the removal procedure.

Removing and installing components

Steps

1. Disconnect the battery cable from the system board, if it was not disconnected earlier.

2. Remove the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly.

3. Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

4. Peel the tapes that secure the speaker cable to the battery.

5. Lift the battery off the palm-rest and keyboard assembly.

Installing the battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Removing and installing components

Steps

1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.

2. Adhere the tapes that secure the speaker cable to the battery.

3. Replace the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

4. Replace the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly.

5. Connect the battery cable to the system board.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Memory

Removing the memory

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image indicates the location of the memory modules and provides a visual representation of the removal procedure.

Removing and installing components

Steps

1. Peel the bottom of the DDR jacket back to access the memory-module slot.

2. Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot until the memory module pops up.

3. Remove the DDR jacket from the memory module.

4. Slide and remove the memory module from the memory-module slot.

NOTE: Repeat step 1 to step 3 to remove the other memory module if required.

Removing and installing components 19

Installing the memory

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the memory modules and provides a visual representation of the installation procedure.

Steps

1. Align the notch on the memory module with the tab on the memory-module slot.

2. Slide the memory module firmly at an angle, into the memory-module slot.

3. Slide the DDR jacket back on the memory module.

4. Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

NOTE: Repeat step 1 to step 3 to install the other memory module if available on your computer.

20 Removing and installing components

5. Press the flaps of the DDR jacket back in place.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Solid-state drive

Removing the solid-state drive 1

Prerequisites

1. Follow the procedure in Before working inside your computer.

CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is turned on or is in

sleep state.

2. Remove the base cover.

About this task

The following image indicates the location of the solid-state drive 1 and provides a visual representation of the removal procedure.

Steps

1. Remove the screw (M2x2) that secures the solid-state drive thermal bracket and the solid-state drive 1 to the system board.

2. Slide the solid-state drive thermal bracket from the peg and lift it from the system board.

Removing and installing components

3. Slide and remove the solid-state drive 1 from the solid-state drive slot.

NOTE: The size of the solid-state drive thermal bracket varies based on the storage type. A solid-state drive thermal

bracket that is designed for an M.2 2280 drive cannot accommodate an M.2 2230 drive and vice versa.

Installing the solid-state drive 1

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

About this task

The following image indicates the location of the solid-state drive 1 and provides a visual representation of the installation procedure.

Steps

1. Align the notch on the solid-state drive 1 with the tab on the solid-state drive slot.

2. Gently slide the solid-state drive 1 into the solid-state drive slot.

3. Slide the solid-state drive thermal bracket under the peg on the system board.

Removing and installing components

4. Align the screw hole on the solid-state drive thermal bracket with the peg on the system board.

NOTE: The size of the solid-state drive thermal bracket varies based on the storage type. A solid-state drive thermal

bracket that is designed for an M.2 2280 drive cannot accommodate an M.2 2230 drive and vice versa.

5. Replace the screw (M2x2) that secures the solid-state drive thermal bracket and the solid-state drive 1 to the system board.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Removing the solid-state drive 2

Prerequisites

1. Follow the procedure in Before working inside your computer.

CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.

2. Remove the base cover.

About this task

The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.

Removing and installing components

+ 52 hidden pages