![](/html/3a/3a45/3a4513bafeed5e53c0b9883b504420d3adc5f4c0dcd032a71d0e677fe1256329/bg1.png)
PROJECT
ITEM #
QUANTITY DATE
APPROVAL
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
CAB4
Mobile enclosed four-stack dish dispensers
Short form specifications
Cabinet top shall be 16-gauge stainless steel with all corners welded and polished and
reinforced with heavy-gauge channels. Cabinet exterior panels and corner support angles shall
be 20-gauge stainless steel. Unit shall have four 4.00" (10.2cm) diameter polyolefin swivel
casters, and non-marking gray bumpers at each corner.
Dispenser tube shall have 3 vertical side channels and a bottom brace of 22-gauge stainless
steel. Top supporting flange shall be 18-gauge stainless steel. Flange, channels and bottom
brace shall be integrally welded together. Flange shall have 3 guide posts molded from high
impact plastic.
Self-leveling mechanisms shall be field adjustable by adding or removing stainless steel
extension springs on perimeter of vertical side channels. The dish carrier head shall be stainless
steel welded rods with a removable 18-gauge stainless steel top plate.
Capacity of tubes shall be approximately 72 dishes, with a maximum stacking height of
24.00" (61.0cm).
NOTE: Models without “-ET” or “-QT” suffix are unheated.
THE FOLLOWING APPLIES TO CAB4-ET EVEN TEMP HEATED DISPENSERS ONLY:
Unit shall be supplied with 9' (2.7m) cord and NEMA 6-20P plug. Electrical connections shall
be 208-230 volt, 60 hertz, single phase.
Each tube shall have its own convection heating module consisting of a single 400 watt
heating element and fan motor, located in the center of the interior bottom cavity. Air intake
shall have a filter. Each tube shall have an adjustable thermostat inside the motor housing and
an ON/OFF switch on one of the dish guide posts.
Unit shall maintain temperature between
120°F–140°F (49°C–60°C).
THE FOLLOWING APPLIES TO CAB4-QT QUICK TEMP HEATED DISPENSERS ONLY:
Unit shall be supplied with 9' (2.7m) cord and NEMA 6-20P plug. Electrical connections shall
be 208-230 volt, 60 hertz, single phase.
Each tube shall have its own convection heating module consisting of a single 700 watt
heating element and fan motor, located in the center of the interior bottom cavity. Air intake
shall have a filter. Each tube shall have an adjustable thermostat inside the motor housing and
an ON/OFF switch on one of the dish guide posts.
Unit shall maintain temperature between
150°F–170°F (66°C–77°C).
Each tube shall have a stainless steel dome cover.
Optional accessories & modifications
• Heavy-duty casters (consult factory)
• Flange-mount feet in lieu of casters
• Special dispenser tube heights
• 12" (30.5cm) dia. stainless steel dish dispenser tray (CAB4-1200, CAB4-1200-ET and
CAB4-1200-QT only)
• Non-marring adjustment rods for oval dishes and various dish diameters (–813 through
–1450 sizes only)
• Stainless steel cover with access to dishes (–813 through –1450 sizes only; standard
on QT models)
• Stainless steel cover
• Hold-down rod for dispenser tubes
• Wrap-around bumpers (adds 1.75" [4.4cm] to overall length and depth)
• Fiberglas
®
panels
• Laminate panels
• Special voltages (consult factory)
Model CAB4-813
![](/html/3a/3a45/3a4513bafeed5e53c0b9883b504420d3adc5f4c0dcd032a71d0e677fe1256329/bg2.png)
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
MSCAB4 03/07
MODEL NUMBER LENGTH DEPTH
DISH DIAMETER
RANGE AMPS
SHIP
WEIGHT
CAB4-500 27.00"/68.6cm 27.00"/68.6cm 3.00"–5.00"/7.6cm–12.7cm 181 lbs/82 kg
CAB4-575 27.00"/68.6cm 27.00"/68.6cm 5.00"–5.75"/12.7cm–14.6cm 185 lbs/84 kg
CAB4-650 27.00"/68.6cm 27.00"/68.6cm 5.75"–6.50"/14.6cm–16.5cm 186 lbs/84 kg
CAB4-725 27.00"/68.6cm 27.00"/68.6cm 6.50"–7.25"/16.5cm–18.4cm 189 lbs/86 kg
CAB4-813 32.25"/81.9cm 32.25"/81.9cm 7.25"–8.12"/18.4cm–20.6cm 213 lbs/97 kg
CAB4-913 32.25"/81.9cm 32.25"/81.9cm 8.12"–9.12"/20.6cm–23.2cm 217 lbs/98 kg
CAB4-1013 32.25"/81.9cm 32.25"/81.9cm 9.12"–10.12"/23.2cm–25.7cm 221 lbs/100 kg
CAB4-1200 36.00"/91.4cm 36.00"/91.4cm 10.12"–12.00"/25.7cm–30.5cm 240 lbs/109 kg
CAB4-1450 42.00"/106.7cm 42.00"/106.7cm 12.00"–14.50"/30.5cm–36.8cm 263 lbs/119 kg
CAB4-500ET 27.00"/68.6cm 27.00"/68.6cm 3.00"–5.00"/7.6cm–12.7cm 17.0 226 lbs/103 kg
CAB4-575ET 27.00"/68.6cm 27.00"/68.6cm 5.00"–5.75"/12.7cm–14.6cm 17.0 230 lbs/104 kg
CAB4-650ET 27.00"/68.6cm 27.00"/68.6cm 5.75"–6.50"/14.6cm–16.5cm 17.0 234 lbs/106 kg
CAB4-725ET 27.00"/68.6cm 27.00"/68.6cm 6.50"–7.25"/16.5cm–18.4cm 17.0 242 lbs/110 kg
CAB4-813ET 32.25"/81.9cm 32.25"/81.9cm 7.25"–8.12"/18.4cm–20.6cm 17.0 270 lbs/123 kg
CAB4-913ET 32.25"/81.9cm 32.25"/81.9cm 8.12"–9.12"/20.6cm–23.2cm 17.0 278 lbs/126 kg
CAB4-1013ET 32.25"/81.9cm 32.25"/81.9cm 9.12"–10.12"/23.2cm–25.7cm 17.0 286 lbs/130 kg
CAB4-1200ET 36.00"/91.4cm 36.00"/91.4cm 10.12"–12.00"/25.7cm–30.5cm 17.0 313 lbs/142 kg
CAB4-1450ET 42.00"/106.7cm 42.00"/106.7cm 12.00"–14.50"/30.5cm–36.8cm 17.0 337 lbs/153 kg
CAB4-813QT 32.25"/81.9cm 32.25"/81.9cm 7.25"–8.12"/18.4cm–20.6cm 17.0 290 lbs/132 kg
CAB4-913QT 32.25"/81.9cm 32.25"/81.9cm 8.12"–9.12"/20.6cm–23.2cm 17.0 298 lbs/135 kg
CAB4-1013QT 32.25"/81.9cm 32.25"/81.9cm 9.12"–10.12"/23.2cm–25.7cm 17.0 306 lbs/139 kg
CAB4-1200QT 36.00"/91.4cm 36.00"/91.4cm 10.12"–12.00"/25.7cm–30.5cm 17.0 333 lbs/151 kg
CAB4-1450QT 42.00"/106.7cm 42.00"/106.7cm 12.00"–14.50"/30.5cm–36.8cm 17.0 351 lbs/159 kg
NA
NA
NA
NA
NA
NA
NA
NA
NA
36.00"
91.4cm
3.62"
9.2cm
5.00"
12.7cm
36.00"
91.4cm
3.62"
9.2cm
JUNCTION
BOX
5.00"
12.7cm
D
L
D
L
Mobile enclosed four-stack dish dispensers
CAB4
NOTES
• CAB4-ET models are
208-230
volt, 60 hertz, single phase, and include a 9' (2.7m) cord with NEMA 6-20P plug. CAB4-QT models are 208-230volt, 60
hertz, single phase, and include a 9' (2.7m) cord with NEMA 6-20P plug.
• Optional adjusting rods (available on 813–1450 models only) reduce the maximum round dish diameter by 1.25" (3.2cm); overall adjustment by rods
is 1.50" (3.8cm). Must be ordered for each individual dispenser tube, non-marring adjustment rods, installed at factory only.
ELEVATION VIEW
CAB4 MODELS
RIGHT END VIEW
CAB4 MODELS
ELEVATION VIEW
CAB4-ET & CAB4-QT
MODELS
RIGHT END VIEW
CAB4-ET & CAB4-QT
MODELS
PLAN VIEW
CAB4
MODELS
PLAN VIEW
CAB4-ET & CAB4-QT
MODELS