Defy GEMINI CERAN HOB, GEMINI MASTER CHEF Owner's Manual
Owner’s
Manual
GEMINI MASTER CHEF MULTIFUNCTION THERMOFAN
UNDER COUNTER OVEN
CONTENTS
2 Introduction
2 Unpacking
2 Cupboard Design
2 Installation
3 Electrical Installation
3 Safety Advice
4 The Control Panel
4 Automatic Oven Timer/Clock
7 The Oven – Functions
10 Solid Plates
11 Ceran Smooth Top
12 Maintenance
13 Problem Check
13 Owner’s Responsibility
13 Service
14 Features and Benefits
www.defy.co.za
INTRODUCTION
Congratulations on the purchase of this quality appliance.
We, the manufacturer, trust that you will enjoy many years of trouble free use. Please
read these instructions carefully before using the oven. This book will provide you with
information on how to operate and care for your appliance in order that you gain the
maximum benefit from it.
UNPACKING
• Please ensure that packaging material is disposed of in a responsible manner. Plastic
bags should be cut up to prevent children playing with them and accidentally
suffocating.
• Remove all packing from the oven cavity and position the accessories.
• If the appliance is damaged in any way, do not use it. Report the damage to your
dealer, who will take the necessary corrective action.
CUPBOARD DESIGN
• Cooking appliances generate considerable heat. The layout and materials of the
mounting cabinet should take account of the characteristics of the oven.
• Surfaces immediately adjacent to the oven should be able to withstand temperatures
of up to 100°C without delaminating or discolouring.
• Gemini ovens exhaust through a vent in the upper part of the handle. The vent in the
lower part of the handle is an air intake.
• Gemini ovens are designed for installation with cupboard doors which provide at least
100mm. clearance alongside and above the oven. The overhanging worktop may be
subjected to heat as well as condensation if moist foods are being cooked.
• Note that the oven door is reversible and may hinge from the left or right. Consult the
nearest Defy Service Centre and they will advise the correct procedure.
INSTALLATION
Aperture
Hob fixing bracket
‘U’ SEAL FOR SOLID
PLATE HOB ONLY
• The hob should be installed in a ventilated cupboard fitted with a sturdy work-top and
must be secured using the fixing brackets provided.
• Place the oven on the floor in front of the aperture and make the electrical connection
before installing. This will ensure enough cable length for subsequent servicing.
• Lift off the top trim and unscrew the bottom trim. This will expose the fixing holes.
• Secure the oven to the cabinet using suitable screws. (Fasteners are not provided.)
• Replace the top and bottom trims.
“This appliance must be earthed and the manufacturer and the seller do
not accept responsibility for any damage due to incorrect installation or
electrical connection.”
ELECTRICAL INSTALLATION
Earth leakage
This appliance should not be connected through an earth leakage system.
Refer to S.A.B.S. 0147.
Connection to the power supply must be carried out by a licensed electrician, who will
ensure that the oven is correctly connected and safely earthed. The rated current is printed
on the serial number label attached to the oven bottom trim.
The appliance must be connected to the mains through a double pole isolating switch
which has a minimum clearance between the contacts of 3 mm. in both poles.
A means for disconnection must be provided in the fixed wiring.
Hob to oven connection—Two 6 pin electrical plugs are used. (Refer to label on oven)
SAFETY ADVICE
• Only use the appliance for preparing food.
• Always keep children away from the appliance when it is in use.
• Do not leave hot fat or oil unattended. If overheating occurs, these could catch fire.
• Switch off the power at the mains in the event of a fault or when cleaning the
appliance.
• Do not store flammable items in the oven. If the oven is inadvertently switched on,
these could catch fire.
• Never cover the bottom oven element with aluminium foil. Cooking times will be
affected and the oven enamel could be damaged.
• Avoid spilling fruit juice, particularly citrus, on the appliance as it could damage the
enamel.
• Always keep the oven door gasket clean as this will enable the door to seal properly.
THE CONTROL PANEL
LEFT
FRONT
PLATE
CONTROL
0
1
8
RIGHT
FRONT
PLATE
CONTROL
0
1
8
LEFT
BACK
PLATE
CONTROL
0
1
8
RIGHT
BACK
PLATE
CONTROL
0
1
8
AU TOM AT IC
OVEN TIMER
AND CL OCK
12:45
STOP
GEMINI MULTI - CHEF
THE OVEN THERMOSTAT IS MARKED DOWN TO 70°C.
WHEN SET TO THIS POSITION, THE OVEN MAY BE USED AS A WARMER
AUTOMATIC OVEN TIMER / CLOCK
BUTTON FUNCTIONS
1 = MINUTE MINDER
2 = COOKING PERIOD
3 = STOP TIME
4 = MANUAL CONTROL
5 = SUBTRACT
6 = ADD
MULTI- FUNC TION
OVEN THERMOSTAT
AND INDICATOR
LIGHT
1
-
+
MULTIFUNCTION
SELECTOR
S
0
8
0
8
1
-
+
65 4321
SETTING THE TIME OF DAY
• When the power is first connected (or after a power failure), the clock display will
flash 00.00.
• To set the clock, press buttons 1 and 2 and hold them down.
• Press button 5 or 6 until the correct time of day is displayed.
• Release the buttons. The clock is now set.
• Please note that the clock has a 24 hour display.
• For example 3.00 PM will be displayed as 15.00.
MINUTE MINDER
• Suppose that you wish to time the boiling of a 5 minute egg.
• First boil the water
• Press and hold button 1. The display will show 00.00
• Press button 6 until the display shows 00.05
• Release the buttons and place the egg in the boiling water. The display will again
show the time of day.
• After 5 minutes the timer will emit an electronic tone which lasts for about one
minute (2 beeps every 2 seconds). To cancel the tone, press any of the buttons.
Note:
• During the operation of the
minute minder, the remaining
time may be displayed by
pushing button 1
• The minute minder can be used
simultaneously and independent
of any automatic control
program
• The display will always revert
to the time of day after any
program has been set.
-
+
65 4321
SWITCHING THE OVEN ON AND OFF AUTOMATICALLY
(AUTOBAKE)
Autobake is intended for dishes such as roasts and casseroles. These are not affected by a
waiting period in a cold oven.
• Prepare your meal and place it in the oven.
• Set the cooking period required by pressing buttons 2 and 6 until the desired period is
displayed.
• Set the stop time by pushing buttons 3 and 6 until the desired stop time is displayed.
• Release the buttons and the clock will again display the time of day.
• The word AUTO will light up on the clock display.
• Set the multi function selector where applicable to the desired cooking function.
• Now set the oven thermostat to the desired temperature setting
The automatic control will automatically switch the oven on and the symbol will
light up in the clock display.
Cooking will commence at the selected temperature and for the selected cooking period.
The oven will automatically switch off at the selected stop time and emit an electronic
tone for about one minute ( 4 beeps every 2 seconds ).To cancel the tone, press any of
the buttons.
Loading...