Dee Zee DZ2050 User Manual

Before returning this product
DZ 2036
to the store of purchase
Contact Dee Zee if you experience the following problems:
•MissingParts  •InstallationProblems/Questions  •WarrantyQuestions
1.800.779.2102
Reviewcompletewarrantypolicyandregisteryourproductat:
www.deezee.com
Dee Zee Running Board Installation Instructions
Congratulations on your purchase of a quality Dee Zee product. Dee Zee is
recognized as having the highest quality running boards and accessories on
the market today. We have earned this reputation by offering our customers
a product they can be proud to place on their vehicles. Dee Zee meets all
the criteria of manufacturing a custom-fit product which guarantees it to
be the easiest product to install.
Note: Please take time to read all of the instructions before beginning this installation.
Warning! Please check for wiring or other obstructions before drilling any holes into the vehicle. If it is necessary to drill any holes into the vehicle, Dee Zee recommends putting a sealant or rust inhibitor around all holes drilled into the body of the vehicle.
Warning! It is the sole responsibility of the vehicle owner to check for tire clearance.
Warning! It is unlawful and dangerous to ride on running boards or side box boards while the vehicle is in motion.
Cleaning Instructions: To maintain the bright finish of your Dee Zee running boards, clean with a mild detergent. For our stainless steel products and accessories, the application of a high grade automotive type wax is recommended.
If you should happen to have any questions with this product or you have an
installation question, please feel free to call us at:
1-800-779-8222
If you would like to find out more information on Dee Zee’s products please
feel free to visit our website at:
WWW.DEEZEE.COM
DZ 2036.PDF 10/18/02
Dee Zee Britetread Running Board Installation Instruction
DZ 2050
DZ 2036
(1999 - Current) Ford Superduty Regular Cab Pickup
Britetread Running
A
Board
G
1/4“ Hex Nut
Britetread Mudflap
B
X2
H
1/4 x 1” Ribneck Carriage Head Bolt
Rocker Panel
C D
Bracket
X2
I
3/8 x 1“ Hex Head Bolt
Running Board Bracket
X4
J
5/16“ Flat Washer
E
X4
K
3/8“ Hex Nut
1/4 x 3/4” Hex Head Bolt
X4
1/4“ Flat Washer
F
L
3/8" Lock Washer
X16
X12
M
1/4 x 1” Sheet Metal Screw
To o ls Re qu i r ed : Outils Nécessaires:
Tin-snips
N
8mm x 30mm Hex Head Bolt
X4
Level
X8
O
8mm Flange Nut
X8
Phillips Head Screwdriver
Tape Measure
X8
P
8mm U-Clip
X4
X28
Q
Bulb-Seal Gasket
X4
Ratchet / Wrench Sizes: 3/8“ 7/16“
13mm
9/16"
X8
10.5 ft.
X8
1/4” Needed 3/16” Needed
Drill
1
Secure britetread mudflap (B) to britetread running board (A) using 1/4 x 3/4” hex head bolts (E), 1/4” flat washers (F), and 1/4” hex nuts (G). Tighten into place using a 7/16” wrench / or socket. Place bulb-seal gasket (Q) onto the backlip of britetread running board (A) and trim flush with the britetread mudflap (B) and the end of britetread running board (A).
Fixez le mudflap de britetread (b) au panneau courant de britetread (a) en utilisant les boulons de tête d'hexa de 1/4 x de 3/4"(e), les rondelles de 1/4" (f), et les écrous 1/4"d'hexa plats (g). Serrez dans l'endroit à l'aide d'une clé de 7/16"/ou du plot. Placez la garniture d'ampoule-joint (q) sur le backlip du panneau courant de britetread (a) et équilibrez à affleurement du mudflap de britetread (b) et de l'extrémité du panneau courant de britetread (a).
A
B
E
Q
F
G
F
Britetread Running Board
7/16“ Wrench or Socket
+ 7 hidden pages