Dee Zee DZ17940 User Manual

Page 1
Before returning this product
DZ 17940
to the store of purchase
Contact Dee Zee if you experience the following problems:
•MissingParts  •InstallationProblems/Questions  •WarrantyQuestions
1.800.779.2102
Reviewcompletewarrantypolicyandregisteryourproductat:
www.deezee.com
Page 2
Dee Zee Molded Mudflap Installation Instructions
Congratulations on your purchase of a quality Dee Zee product. Dee Zee is
recognized as having the highest quality running boards and accessories on
the market today. We have earned this reputation by offering our customers
a product they can be proud to place on their vehicles. Dee Zee meets all
the criteria of manufacturing a custom-fit product which guarantees it to
be the easiest product to install.
Please take time to read all of the instructions before beginning this installation.
If you should happen to have any questions with this product or you have an
installation question, please feel free to call us at:
1-800-779-8222
If you would like to find out more information on Dee Zee’s products please
feel free to visit our website at:
WWW.DEEZEE.COM
DZ 17940.PDF 06/25/07
Page 3
Dee Zee Mudflap Installation Instruction
DZ 17940
(1999 - Current) Chevy P/U (Front)
Rubber Mudflap
A
F
3M Protection Film (10”) (Cut in half)
X1 Set
B
1/4x1” Hex Head Bolt
X2
1/4” Flat Washer
C D
PN 265B PN 72BPN 71B
X2
1/4” Hex Nut
X2
E
1/4” Flat Washer
X2
X1
Tools Required:
Ratchet / Wrench Sizes:
7/16”
Short Phillips Screwdriver
Page 4
1
3M Protective Film Installation: Dee Zee mudflaps are designed to fit snugly into the wheel well. To protect your vehicle, Dee Zee has included a 3M protective film.
1) Hold the mudflap up to wheel well to determine 3M protective film placement.
2) Thoroughly clean the area where the film is to be installed using 3M brand adhesive cleaner or other petroleum distillate based cleaner.
3) Cut the film to the proper shape for your application.
4) Mix a solution of water and dishwasher detergent into a spray bottle.
5) Remove film from the protective liner and spray with the water solution.
6) Apply the film to the fender, adhesive side down and spray total area with water solution.
7) Remove any air bubbles in film using a wet sponge.
8) Let film dry completely before installing mud flap.
Fender
3M Protective Film Location
2
2
D
Option #1
Remove these screws and save them to re-use them later in the installation.
Remove plugs
Page 5
3
4
Option # 1
Mark the Wheel Well Liner flush with the bottom of the fender. Cut the extra Wheel Well Liner off. This needs to be done for Option #1 only.
Mark and cut flush.
Place the mudflap up to the wheel well, over the wheel well liner. Insert the top two screw and washer from Step #1 into the holes. Insert in the bottom hole a 1/4” X 1” Phillips Head Screw (B) and 1/4” Fender Washer (C) then place a 1/4” Flat Washer (E) and 1/4” Nut on the 1/4” X 1” Phillips Head Screw (B).
Re-use the screws and washer removed in step #1
B C D E
Note: Use large washer on this side of mudflap
Page 6
½
3
Option # 2
See Step #1 and #2 from Option #1 for Step #1 and #2 of Option #2.
The Wheel Well Liner does not need to be cut in option #2. The Mudflap slides in between the Wheel Well Liner and the Fender.
The Wheel Well Liner does not need to be cut in Option #2
4
Place the mudflap between the fender well and the wheel well liner. Insert the top two screw and washer from Step #1 into the holes. Insert in the bottom hole a 1/4” X 1” Phillips Head Screw (B) and 1/4” Fender Washer (C) then place a 1/4” Flat Washer (E) and 1/4” Nut on the 1/4” X 1” Phillips Head Screw (B).
Mudflap placed between the Wheel Well Liner and the Fender Well.
Re-use the screws and washer removed in step #1
B C D E
Note: Use large washer on this side of mudflap
Loading...