Dee Zee DZ16280 User Manual

Page 1
Page 2
INSTALLATION INSTRUCTIONS
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
Bill of Materials:
Quantity Part Number English Description
2 Various Boards
1 B 2041LP Left Middle Bracket
1 B 2042LP Left Rear Bracket
1 B 2040RP Right Front Bracket
1 B 2041RP Right Middle Bracket
1 B 2042RP Right Rear Bracket
10 PN 525 M8 x 25mm Flange Bolt
10 PN 835 Double Weld Tab Plate
2 PN 108 M6 x 25mm Bolt
12 PN 524 M8 x 25mm Square Head Bolt
Read and understand these instructions BEFORE attempting to install this product.
01.31.12
2
01.17.11
Page 3
INSTALLATION INSTRUCTIONS
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
Getting Started.
Begin installation on left side of vehicle by observing the front, and rear bracket locations.
1
2
Front Left Bracket Location
Remove rubber plugs from both hole locations.
4
3
Middle Left Bracket Location
Remove rubber plug from hole location (3). location (4) will have a preset insert
.
01.31.12
3
01.17.11
Page 4
INSTALLATION INSTRUCTIONS
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
6
5
Rear Left Bracket Location
Remove rubber plug from both hole locations (5) and (6).
2
1
Front Left Bracket
Identify the Front Left Bracket and place M8 x 25mm Flange Bolt and secure with Double Weld Tab Plate in the front hole (1) of Left Front bracket, and M8 x 25mm Flange Bolt and secure with Double Weld Tab Plate in the rear hole (2).
01.31.12
4
01.17.11
Page 5
INSTALLATION INSTRUCTIONS
7
7
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
4
3
Middle Left Bracket
Identify the Middle Left Bracket and place M8 x 25mm Flange Bolt and secure with Double Weld Tab Plate in the front hole (3) of Left Front bracket, and M6 x 25mm Flange Bolt in the rear hole (4) to insert in vehicle.
6
Rear Left Bracket
Identify the Rear Left Bracket and place M8 x 25mm Flange Bolt and secure with Double Weld Tab Plate in the front hole (6) Bracket and place M8 x 25mm Flange Bolt and secure with Double Weld Tab Plate in the front hole (7) of left rear bracket.
01.31.12
5
01.17.11
Page 6
INSTALLATION INSTRUCTIONS
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
2
1
Front Left Bracket Location
Place tabs into openings in vehicle and tighten with 13mm wrench for locations (1 and 2).
4
3
Middle Left Bracket Location
Insert M6 bolt into bracket and preset in location (4). Place tab into opening in vehicle in the front location (3) and tighten with 13mm wrench.
6
01.31.12
01.17.11
Page 7
INSTALLATION INSTRUCTIONS
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
7
6
Rear Left Bracket Location
Insert M8 bolt into bracket and Nutsert in location (4). Place tab into opening in vehicle in the rear location (3) and tighten with 13mm wrench. Tighten with 13mm wrench.
Install Left Side Step
Place the 8mm square head bolts into the two bolt channels of the running board and slide toward either end of the board. For this application, there should be two bolts in each channel on opposite ends of the board.
7
01.31.12
01.17.11
Page 8
INSTALLATION INSTRUCTIONS
Accessory Description
DZ 16280
NXc Running Board
Year / Model
2010 Hyundai Sante Fe
Place running board onto the brackets. Align 8mm square head bolts in the bottom of the running board with holes in the brackets. Completely tighten brackets to vehicle. Center board on vehicle between wheel well openings or until desired appearance is acquired. Adjust board in/out on vehicle until desired appearance is met. Secure board into place using 8mm hex nuts.
Right Side.
Repeat above steps for the right side of vehicle to complete.
8
01.31.12
01.17.11
Loading...