Page 1
Before returning this product
to the store of purchase
Contact Dee Zee if you experience the following problems:
•MissingParts
•InstallationProblems/Questions
•WarrantyQuestions
1.800.779.2102
Hoursofoperation:8am-5pmCST,Mon-Friday
Reviewcompletewarrantypolicyandregisteryourproductat:
www.deezee.com
Page 2
Dee Zee Running Board Installation Instructions
Congratulations on your purchase of a quality Dee Zee product. Dee Zee is
recognized as having the highest quality running boards and accessories on
the market today. We have earned this reputation by offering our customers
a product they can be proud to place on their vehicles. Dee Zee meets all
the criteria of manufacturing a custom-fit product which guarantees it to
be the easiest product to install.
Note: Please take time to read all of the instructions before beginning this installation.
War ning! Please check for wiring or other obstr uctions before drilling any holes into
the vehicle. If it is necessar y to drill any holes into the vehicle, Dee Zee recommends
putting a sealant or rust inhibitor around all holes drilled into the body of the vehicle.
War ning! It is the sole responsibility of the vehicle owner to check for tire clearance.
War ning! It is unlawful and dangerous to ride on r unning boards or side box boards
while the vehicle is in motion.
Cleaning Instructions: To maintain the bright finish of your Dee Zee running boards,
clean with a mild deter gent. For our stainless steel products and accessories, the
application of a high grade automotive type wax is recommended.
If you should happen to have any questions with this product or you have an
installation question, please feel fr ee to call us at:
1-800-779-8222
If you would like to find out mor e infor mation on Dee Zee’s products please
feel free to visit our website at:
WWW.DEEZEE.COM
Page 3
VARIES
X1 LH/ X1 RH
B 2161LP/RP
X1 LH/ X1 RH
THIS SPACE INTENTIONALLY LEFT BLANK
B 2162LP/RP
X1 LH/ X1 RH
FP0200
X2
GSK-41
9.5 FT.
PN 87
X8
PN 70
X4
PN 97
X4
PN 72
X16
PN 71
X12
BRITE TREAD RUNNING BOARD INSTALLATION INSTRUCTION
BRITE TREAD RUNNING BOARD INSTALLATION INSTRUCTIONBRITE TREAD RUNNING BOARD INSTALLATION INSTRUCTION
BRITE TREAD RUNNING BOARD INSTALLATION INSTRUCTION
DZ 1060 GMC REGULAR CAB 2014-CURRENT
DZ 1060 GMC REGULAR CAB 2014-CURRENTDZ 1060 GMC REGULAR CAB 2014-CURRENT
DZ 1060 GMC REGULAR CAB 2014-CURRENT
A B
DZ 1057 CHEVY REGULAR CAB 2014-CURRENT
DZ 1057 CHEVY REGULAR CAB 2014-CURRENTDZ 1057 CHEVY REGULAR CAB 2014-CURRENT
DZ 1057 CHEVY REGULAR CAB 2014-CURRENT
RUNNING BOARD FRONT BRACE
C
E
MUD FLAP
REAR BRACE
D
BULB GASKET 1/4 X 3/4" HEX
1/4 X 1" RIBNECK
CARRIAGE BOLT
HF G
HEAD BOLT
SHEET METAL SCREW 1/4" FLAT WASHER
I K
DZ 1057 1 of 8 8/7/2013
J
1/4" HEX NUT
Page 4
WRENCH/RATCHET
TORQUE WRENCH
CLAMP
21mm, 3/8", 7/16"
TIN SNIPS
Locate the 2 mounting locations.
The driver's side is shown. The front of the vehicle is to the left of the picture.
TOOLS REQUIRED
1
DZ 1057 2 of 8 8/7/2013
Page 5
Remove the bolt from the body shock mount at each of the mounting locations using a 21mm socket.
2
REMOVE
BOLT
DZ 1057 3 of 8 8/7/2013
Page 6
Put the body shock mount bolt through the hole in the brace and thread it back into the body shock
mount. Align the braces so that they are perpendicular to the side of the vehicle. Tighten the bolts
to 44 ft-lbs plus another half turn.
The driver's side is shown. The front of the vehicle is to the left of the pictures.
3
REAR
FRONT
DZ 1057 4 of 8 8/7/2013
Page 7
Place the bulb-seal gasket [F] onto the backlip of the runing board [A]. Cut the bulb-seal gasket
with tin snips so that it is flush with the ends of the board
Loosely attach the mud flap [E] to the end of the running board using
the 1/4" x 3/4" hex head bolt [H], the 1/4" flat washer [J], and the 1/4" hex nut [K].
Snug the bolts, but do not completely tighten at this time.
4
5
DZ 1057 5 of 8 8/7/2013
Page 8
Place the running board on the braces with the bulb seal up against the bottom of the vehicle.
Align the board with the vehicle and make sure that the mud flap is up against the wheel well.
6
BULB SEAL
AGAINST
DZ 1057 6 of 8 8/7/2013
Page 9
Using the slots in the brace as a guide, drill a 1/4" hole at each mounting location.
Clamp the board to the brace to hold it in position.
Attach the running board to the angle brace using the 1/4" x 1" ribneck carriage bolt [G],
1/4" flat washer [J], and 1/4" hex nut [K]. Tighten using a 7/16" wrench or deep well socket.
7
8
DZ 1057 7 of 8 8/7/2013
Page 10
Pressing the flap up against the wheel well, drill two 3/16" holes through the hole in the mud flap
into the sheet metal of the wheel well.
Repeat for the rear of the board.
Check all hardware to make sure it has been tightened.
Repeat the assembly steps for the other side of the vehicle.
9
Attach the mud flap to the wheel well using two sheet metal screws [I] with a 3/8" socket.
10
DZ 1057 8 of 8 8/7/2013
Loading...