DE DIETRICH DVH610 User Manual
13
EN
CONTENTS
1 / SAFETY INSTRUCTIONS
• Important warnings __________________________________________ 14
2 / INSTALLING YOUR DISHWASHER
• Dimensions for building in appliances __________________________ 15
• List of parts supplied ________________________________________ 15
• Connecting to the water supply ________________________________ 16
• Draining away the waste water ________________________________ 17
• Electricla connection ________________________________________ 18
• Insertion into the niche ______________________________________ 19
• Levelling by adjusting the feet ________________________________ 19
• Fitting the door panel (Cladding with a single panel) ______________ 20
• Fitting the door panel (Cladding with two elements) ______________ 21
• Appliances built-in under o hob ________________________________ 22
• Fixing in the niche __________________________________________ 22
• Sound-proofing seals ________________________________________ 22
• Balancing the door (left and right) ______________________________ 22
• Refitting the plinth __________________________________________ 23
• Table for cutting away the plinth ______________________________ 23
Important:
When building in appliances, please use the attached installation diagram.
Important:
Please read this installations manual carefully in order to comply with the instruc-
tions for installing and fitting your machine.
NB:
This installations manual covers various models. There may be some slight diffe-
rences between your appliance and the descriptions shown.
14
EN
1/ SAFETY INSTRUCTIONS
• IMPORTANT WARNINGS
Important:
After unpacking your appliance, make sure that it has not suffered any damage during
transport. Never connect up a damaged appliance. If your appliance is damaged, please contact
your dealer.
Danger:
If your appliance operates incorrectly, disconnect it (pull out the plug) or switch off the
circuit concerned and close the water supply tap. Contact our After-Sales Service.
Important:
All the necessary electrical and plumbing work for installing the appliance must respectively be carried out by a qualified electrician and plumber.
— Once you have installed your appliance, ensure that it is not resting on the power cable or the
water supply or drain hoses.
— The appliance must be kept disconnected from the mains supply throughout the whole installation process.
— Check that your appliance’s Earth circuit complies with the prevailing regulations.
— The electrical connection details on the manufacturer’s plate on your machine must match
those for the mains power supply.
Important:
For safety’s sake, do not leave your dishwasher’s door fully open after use.
If your dishwasher is being installed on a carpeted floor, ensure that the feet are set to leave
an air space under the appliance.
15
2 / INSTALLING YOUR DISHWASHER
EN
Fig. 1
•
LIST OF PARTS SUPPLIED
Cups for front feet
Self-adhesive anti-condensation plate
Foam sound-proofing seal
Sound-proofing seals + self-adhe-
sive
fixing strips (if necessary)
Lower panel positioning screws
Panel fixing screws
Screws for fixing the appliance to the unit
Drain connection collar
Wrench for adjusting the front feet
Panel fixing screws
•
DIMENSIONS FOR BUILDING IN APPLIANCES
You can insert your appliance under an existing worktop provided that the relevant niche corresponds to the dimensions on the sketch below (Fig. 01).
?
547
642 à 730 maxi
3
L = 75
L = 40
16
2 / INSTALLING YOUR DISHWASHER
EN
• CONNECTING TO THE WATER SUPPLY
AA
BB
Danger:
The symbol indicates that
the hose is fitted with an electrical device
for cutting off the water supply (depending
on the model). Do not leave this hose in
water and do not cut it.
NB:
Any connection to a water conduit
necessarily involves the risk of a leak occurring, whatever the precautions taken.
Therefore, always close the water tap when
you are not using your machine.
This dishwasher can be supplied with cold
water or hot water up to a maximum of 60°C.
When supplying with hot water, check that
your original hose allows such connection
(red marking on the hose). However, we
recommend that you connect to the cold
water supply. Your appliance is fitted with a
supply hose 1.50m long.
Connect the hose to a tap with a threaded
end, diameter 20/27 (3/4" BSP).
Check that the water pressure does not
exceed the values below:
Flow: 10 l/min minimum.
Pressure: 1 to 10 bars (0.1 - 1 MPa)
.
If the water pressure is too high, please fit a
pressure regulator. Please contact your local
Water Authority for advice on the water pressure in your region.
Warning:
If you use a self-piercing tap, check
that there is sufficient water flow.
Check that the hose seal is present and that
the connection is tight .
Do not re-use any previously used hoses for
making the connection.
Avoid any kinks or constrictions in the hose,
which could prevent the water from passing
or slow down its flow, particularly when building in the appliance under the worktop .
If the appliance is connected to new pipes or
pipes that have not been used for a certain
length of time, let the water run for a few
minutes before connecting the water hose to
avoid and deposits of sand or rust that could
block the water hose’s filter.
BB
AA
AA
00..11-- 11 MMPPaa
11--1100 bbaarrss
MMiinniimmuumm 1100LL//mmiinn
Loading...