FR GUIDE D'UTILISATION
EN GUIDE TO INSTALLATION
DE BETRIEBSANLEITUNG
DA BRUGERVEJLEDNING
Hotte décor
Decorative Hood
Dekor-Dunstabzugshaube
Emhætte med dekorativt panel
21
Dear Customer,
You have just acquired a
DDEE DDIIEETTRRIICCHH
hood and we would like to
thank you.
Our research teams have created this new generation of appliances
for you. Their quality, design, features and technological advances
make them exceptional products, and reveal our unique know-how.
Your new
DDEE DDIIEETTRRIICCHH
hood will blend harmoniously into your
kitchen and will perfectly combine cooking performance and ease of
use. We wanted to offer you a product of excellence.
In the
DDEE DDIIEETTRRIICCHH
product line, you will also find a wide range of
hobs, ovens, microwaves, cookers, dishwashers and fridges, that you
can coordinate with your new
DDEE DDIIEETTRRIICCHH
hood
Of course, in an ongoing effort to best satisfy your demands with
regard to our products, our after-sales service department is at your
disposal and ready to listen in order to respond to all of your questions
and suggestions (contact information at the end of this booklet).
Visit our website
wwwwww..ddeeddiieettrriicchh--eelleeccttrroommeennaaggeerr..c
coomm
, where you will
find our latest innovations as well as useful and complementary
information.
DE DIETRICH
Setting New Values
As part of our commitment to constantly improving our products, we reserve the right to make
changes to them based on technical advances to their technical and functional features and
appearance.
Warning:
Before installing and using your appliance, please carefully read this Guide to
Installation and Use, which will allow you to quickly familiarise yourself with its operation.
FR
02
EN
21
DE
39
DA
58
22
TABLE OF CONTENTS
EN
1 / NOTICES TO THE USER
••
Safety recommendations
____________________________________
23
••
Environmental protection
____________________________________
24
••
Description of your appliance
________________________________
25
2 / INSTALLING YOUR APPLIANCE
••
Using the evacuation mode
__________________________________
26
••
Using the recycling mode
___________________________________
26
••
Electrical connections
______________________________________
27
••
Assembling the hood
_______________________________________
28
••
Assembling the ventilation shaft
º Outdoor evacuation
__________________________________
30
º Recycling
___________________________________________
31
3 / USING YOUR APPLIANCE
••
Description of control panel
_________________________________
32
••
Auto stop fan
______________________________________________
35
••
Auto stop lighting
__________________________________________
35
4 / CARING FOR AND CLEANING YOUR APPLIANCE
••
Cleaning the filter cartridges
_________________________________
36
••
Changing the carbon filter
___________________________________
36
••
Cleaning the outer surfaces
__________________________________
37
••
Changing the light bulb
_____________________________________
38
••
Maintaining your appliance
__________________________________
38
5 / TROUBLESHOOTING
__________________________________________
39
6 / AFTER-SALES SERVICE
________________________________________
40
23
1 / NOTICES TO THE USER
EN
SAFETY RECOMMENDATIONS
——
This oven was designed for use by private
persons in their homes.
——
This appliance is not intended to be used by
persons (including children) with reduced
physical, sensory or mental abilities, or persons
lacking experience or awareness, unless using
it with the help of a person reponsible for their
safety, or under supervision and with prior
instruction in its use. Children should be
supervised to ensure that they do not play with
the appliance.
——
When you receive the appliance, unpack or
have it unpacked immediately. Give it an overall
general inspection. Make note of any concerns
or reservations on the delivery slip and make
sure to keep a copy of this form.
——
Your appliance is intended for standard
household use. Do not use it for commercial or
industrial purposes or for any other purpose
than that for which it was designed.
——
Do not modify or attempt to modify any of the
characteristics of this appliance. This would be
dangerous to your safety.
——
Repairs must only be carried out by an
approved specialist.
——
Always unplug the hood before cleaning it or
performing other maintenance acts.
——
Provide adequate ventilation for the room in
the case of simultaneous use of the hood and
other appliances powered by an energy source
other than electricity. This will prevent the hood
from aspirating the combustion gases.
——
You should never "flambé" dishes under the
hood or operate gas rings under the hood
without placing cookware on them (the flames
sucked up into the hood can damage the
appliance).
——
When frying food under the appliance, you
must carefully monitor the preparation at all
times.
Oils and grease brought to very high
temperatures can catch fire.
——
Respect the recommended frequency of
cleanings and filter replacements. The
accumulation of grease deposits may cause a
fire.
——
The hood should never be used over a
combustible fuel burning stove (wood, coal,
etc.).
——
Never use steam or high-pressure devices to
clean your appliance (requirement imposed by
electrical safety).
——
With a view to constantly improving our
products, we reserve the right to modify their
technical, functional or aesthetic
characteristics, making any changes to their
features considered necessary or desirable in
view of technical progress.
——
In order to easily locate the reference
information for your appliance, we recommend
that you note these data on the "After-Sales
Service Department and Customer Relations"
page.
(This page also explains to you where to find
this information on your appliance.)
••
Attention
Keep this user guide with your
appliance. If the appliance is ever sold or
transferred to another person, ensure that
the new owner receives the user guide.
Please become familiar with these
recommendations before installing and
using your oven. They were written for your
safety and the safety of others.
Warning
In the case of a kitchen heated by a
device connected to a chimney (a stove, for
example) the "recycling" version of the
hood should be installed. Do not use the
hood without metal filters.
Suitable ventilation should be provided in
the room when the hood is used at the
same time as appliances operated by gas
or another combustible fuel.
24
1 / NOTICES TO THE USER
EN
Warning
Installation should only be performed by installers and qualified technicians.
Warning
Remove the protective film from the filter cartridge before use.
ENVIRONMENTAL PROTECTION
••
— This appliance's packaging material is recyclable. Help recycle it and protect the environment
by dropping it off in the municipal receptacles provided for this purpose.
— Your appliance also contains a great amount of recyclable material. It is marked with this label
to indicate the used appliances that should not be mixed with other waste. This way, the
appliance recycling organised by your manufacturer will be done under the best
possible conditions, in compliance with European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment. Contact your town hall or your retailer for the
used appliance collection points closest to your home.
— We thank you doing your part to protect the environment.
25
1 / NOTICES TO THE USER
EN
••
DESCRIPTION OF YOUR APPLIANCE
Vents
Ventilation shaft
Top surface
Control panel
A
B
C
D
B
C
D
A
575 / 1027 mm
90 mm
533 mm
500 mm
274 mm
271 mm
1200 mm
26
2 / INSTALLING YOUR APPLIANCE
EN
USING THE EVACUATION MODE
If you possess an outlet to t
he exterior
(fig. 1)
Your hood can be connected to this outlet
using a flue (minimum diameter Ø mm that is
enamelled, in aluminium, flexible or made of
inflammable material). If your flue is less than
125 mm in diameter,
yyoouu mmuusstt uussee tthhee
rreeccyycclliinngg mmooddee..
••
USING THE RECYCLING MODE
If you do no
t possess an outlet to the exterior
(fig. 2)
All of our appliances can be used in recycling
mode.
In this case, you should add an active carbon
filter which will keep in odours.
(See Chapter 4: Changing the carbon filter.)
••
- The appliance must be unplugged during installation or when any repairs or maintenance work
is being performed.
- Ensure that the network voltage corresponds to the voltage noted on the identification plate
located inside the hood.
- If the electrical installation at your residence requires any changes in order to hook up your
Appliance, call upon a professional electrician.
- If the hood is being used in evacuation mode, do not connect the appliance to a combustion
gas exhaust duct (boiler, chimney, etc.) or to a CMV (controlled mechanical ventilation) system.
- Under no circumstances should the exhaust duct empty into the attic.
- Install the hood at a safe distance of at least 70 cm from an electric, gas or combined cooking
hob.
125
150
fig. 1
fig. 2
125
150
27
2 / INSTALLING YOUR APPLIANCE
EN
Warning
This appliance is delivered with a
H 05 VVF power cord that has three-
0.75 mm
2
conductors (neutral, phase and
ground). It must be connected to the main
power supply (which should be a 220-240 V
single phase current) via a CEI 60083
standardised socket that should remain
accessible after installation, in keeping with
installation guidelines.
We cannot be held responsible for any
accident resulting from an inexistent,
defective or incorrect ground lead. The fuse
for your installation must be 10 or 16A. If
the power cable is damaged, call the aftersales service department in order to avoid
danger.
Warning
If the electrical installation at your
residence requires any changes in order to
hook up your appliance, call upon a
professional electrician.
Warning
If the hood displays any malfunctions,
unplug the appliance or remove the fuse
corresponding to the electrical socket
where your appliance is plugged in.
••
ELECTRICAL CONNECTIONS
During installation and maintenance
operations, the appliance must be unplugged
from the electrical grid; fuses must be cut off
or removed.
The electrical connections are made before
the appliance is installed in its housing.
Ensur
e that:
- the electrical installation has sufficient
voltage,
- the electrical wires are in good condition,
- the diameter of the wires complies with the
installation requirements.
28
2 / INSTALLING YOUR APPLIANCE
EN
Tip
Adjust the level of your hood before
fully tightening up the four D and E screws.
ASSEMBLING THE HOOD
Warning
The hood must be installed in
compliance with all applicable regulations
concerning the ventilation of premises. In
France these regulations are described in
DTU 61.1 from the CSTB. In particular, the
evacuated air should never be conveyed to a
duct used to evacuate smoke from
appliances that use gas or other combustible
fuels. Unused ducts may only be used after
approval from a competent specialist.
The minimum distance between the cooking
surface and the lowest part of the hood must
be 70 cm. If the instructions for the hob
installed under the hood specify a distance of
more than 70 cm, this requirement must be
respected.
— Draw a horizontal line 70 cm minimum from
the cook top (fig. 1).
— Draw a vertical line (B/fig. 1) on the wall that is
centred over the cook top and that extends
from the horizontal line drawn in the previous
step (A) to the ceiling.
— Cut the drilling template by following the
dotted lines to obtain two parts, C1 and C2
(fig. 1).
— Place the C2 template (fig. 1) on the wall,
superimposing the line that represents the
hood's axis over vertical line B (fig. 1) drawn in
a previous step.
— Place the C1 template (fig. 1) against the wall
flush with the ceiling.
— Drill the six holes. Insert the 6 wall plugs.
FFoorr tthhee DDHHDD112200XXEE mmooddeell,, ffoollllooww tthhee aaddddiittiioonnaall
iinnssttrruuccttiioonnss ((ffiigguurree 22)) oonn tthhee ffoolllloowwiinngg ppaaggee..
— Screw in the top two screws for the hood
(D/fig. 1), leaving 5 mm sticking out from the wall.
••
=
=
> 70 cm
5mm
x 2
fig. 1
A
B
E
D
C1
C2
29
2 / INSTALLING YOUR APPLIANCE
EN
fig. 4
fig. 3
D
E
J
— Remove the filter cartridges (J/fig. 4).
— Screw in the two bottom screws (E/fig. 4).
***********************************
FFoorr tthhee DDHHDD112200XXEE mmooddeell oonnllyy::
— Screw in the two additional bottom screws
(K/fig. 4).
***********************************
fig. 2
F
H
H
***********************************
FFoorr tthhee DDHHDD112200XXEE mmooddeell oonnllyy::
— Draw a horizontal line (F/fig. 2) through the two
previously drilled holes (G).
— Drill the two additional holes (H/fig. 2) located
on the line (F) at a distance of 35 cm from the
initial holes (G).
— Insert the two additional wall plugs.
— Screw in the top two screws for the hood
(D/fig. 1), leaving 5 mm sticking out from the wall.
*****************************************
G
K
K
— Hang the suction hood on the two screws
(fig. 3).
Tip
Before fully tightening the four D and E
screws (or six D, E and K screws depending
on the model), adjust the level of the hood.
35 cm
35 cm
30
2 / INSTALLING YOUR APPLIANCE
EN
ASSEMBLING THE VENTILATION
SHAFT
••
Outdoor evacuation
— Using the two screws (fig. 1), attach the metal
chimney bracket against the wall, flush with the
ceiling for support.
— Mount the back-flow valve near the motor
outlet (fig. 2). This back-flow valve makes it
possible to block the entry of air from the
outside.
— If a 125 mm flue is being installed, use the
adapter provided (fig. 3).
If the diameter of your exterior flue is less than
125 mm, you must connect your hood in
recycling mode.
— Slide the end of the flue over the motor outlet
(fig. 4).
— Prepare your telescoping ventilation shaft,
taking care not to block the vents (fig. 4).
Fit the ventilation shafts into one another as far
as they will go.
— Attach the upper portion of the chimney (B/fig.
4 on the metal chimney bracket (A/fig. 4) using
the two screws (G/fig. 4).
— Adjust the length of the telescoping chimney
by bringing down the lower part and fitting it into
the top of the hood.
••
A
B
C
D
E
CChhiimmnneeyy bbrraacckkeett
TTeelleessccooppiinngg vveennttiillaattiioonn sshhaafftt
FFlluuee
AAddaapptteerr
BBaacckk--ffllooww vvaallvvee
MMoottoorr oouuttlleett
CChhiimmnneeyy hhoolld
diinngg ssccrreeww
F
G
=
=
fig. 1
fig. 4
fig. 2 fig. 3
A
C
D
E
F
G
B
31
2 / INSTALLING YOUR APPLIANCE
EN
••
Recycling
— Remove the back-flow valve (fig. 1).
— Using the two screws (fig. 2), attach the plastic
smoke deflector against the wall, flush with the
ceiling for support. Be careful to centre the
deflector in relation to the vertical line drawn on
the wall (fig. 2).
— Slide one end of the flue over the deflector and
the other end over the motor outlet (fig. 3).
— Prepare your ventilation shaft, taking care to
face the vents upward so that they are visible
(B/fig. 3).
— Attach the upper portion of the chimney
(C/fig. 3) on the metal smoke deflector (A/fig. 3)
using the two screws (F/fig. 3).
— Adjust the length of the telescoping chimney
by bringing down the lower part and fitting it into
the top of the hood.
Tip
For optimal use of your appliance, we
recommend that you connect the hood to a
150 mm-diameter flue (not delivered with the
appliance). Minimise the number of angles
and bends and the lengths of the flue. In the
event that the hood will be operated using
outdoor evacuation, you should ensure a
sufficient inflow of fresh air to avoid a
pressure deficiency in the room.
A
B
C
D
E
SSmmookkee ddeefflleeccttoorr
VVeennttss
TTeelleessccooppiinngg vveennttiillaattiioonn sshhaafftt
FFlluuee
MMoottoorr bbrraacckkeett
CChhiimmnneeyy hhoollddiinngg ssccrreeww
fig. 1
=
=
fig. 2
F
fig. 3
A
B
D
E
F
C
32
3 / USING YOUR APPLIANCE
EN
••
DESCRIPTION OF CONTROL PANEL
••
Four-speed electronic model
A
B
C
D
E
Light
A
B
C
Timing /
Delayed stop (10 minutes)
Display
Switching the hood On / Off
Selecting the speed in manual
mode.
Automatic standby
Automatic function
Filter saturation
D
Automatic mode
E
This hood can be used in either automatic or manual mode.
33
3 / USING YOUR APPLIANCE
EN
A
B
C
D
E
MM
AANNUUAALL MMOODDEE
..
The speed is selected manually, power 1 to 4.
Press once on C = speed 1 and every time you press down again the hood switches to the
next speed.
Press down and hold C to stop the hood.
If you would like a delayed stop in manual mode,
press button B and the hood will stop after 10 mins.
AA
UUTTOOMMAATTIICC MMOODDEE
Press E for automatic mode.
is displayed, the hood is in automatic mode.
is displayed, the hood is set to function automatically.
During cooking, the speed is adjusted automatically by the hood according to the type of
cooking.
At the end of cooking, is displayed when suction is completed (shortly after the end of
cooking).
To deactivate automatic mode or automatic standby at anytime press down on C and hold;
the hood turns off.
34
3 / USING YOUR APPLIANCE
EN
A
B
C
D
E
SS
EETTTTIINNGG TTHHEE HHOOOODD
In automatic mode, the hood’s sensitivity needs to be suited to the cooking hob.
Press on both the C and E buttons for 2 seconds.
The display shows 1,2 or 3 lines according to the type of hob.
Press the C button until you reach the correct symbol (see the table below).
Press the A button to confirm the setting.
After confirmation the hood switches to automatic standby mode.
Induction hob
Gas hob
Induction/gas hob
Glass hob
Hob with cast iron burners
Induction/ceramic hob
Filter saturation indicator
The symbol is displayed when the hood is off or in automatic standby mode. This message means that you should clean your filter cartridges.
When the filters have been cleaned, press the B button when the hood is off or in automatic
standby mode.
35
3 / USING YOUR APPLIANCE
EN
If you forget to turn off your hood, it will automatically turn itself off after nine hours of
operation.
If you forget to turn off the light, it will automatically turn itself off after nine hours of
operation.
••
AUTO STOP FAN
••
AUTO STOP LIGHTING
36
4 / CARING FOR AND CLEANING YOUR APPLIANCE
EN
Warning
Always unplug the hood before cleaning it or performing other maintenance acts.
Regular maintenance of your appliance is a guarantee of proper functioning, good
performance and durability.
Warning
Failure to respect the guidelines for cleaning the appliance and filters may cause fires.
Please carefully adhere to the maintenance recommendations.
CLEANING THE FILTER
CARTRIDGES
They must be cleaned after approximately
30 hours of use or at least once a month.
These filters can be cleaned in a vertical
position in your dishwasher.
((DDoo nnoott aallllooww
tthheemm ttoo ttoouucchh ddiirrttyy ddiisshheess oorr ssiillvveerrwwaarree.. ))
Use a brush, hot water and mild detergent.
Rinse and dry them thoroughly before
returning them to the hood.
••
Dismantling the filter cartridge
(fig. 1)
— Turn the built-in filter cartridge handle.
— Tilt the filter cartridge downward.
••
CHANGING THE CARBON
FILTER
Replace it after approximately 120 hours of
use. You should order these filters from your
dealer (quoting the reference shown on the
identification plate located inside the hood)
and note the date the filter was changed.
— Remove the filter cartridge (fig. 2).
— Place the carbon filter on the filter cartridge
on the inside of the hood.
— Pull the two fastener clips over each side of
the filter cartridge.
— Repeat these steps for all the filter cartridges.
••
fig. 2
37
4 / CARING FOR AND CLEANING YOUR APPLIANCE
EN
To preserve your appliance, we recommend that you use Clearit cleaning products.
PPrrooffeessssiioonnaall eexxppeerrttiissee
sseerrvviinngg iinnddiivviidduuaallss
Clearit offers you professional products and solutions designed for the daily care of your
household appliances and kitchens.
They are on sale at your regular retailer, along with a complete line of accessories and
consumable products.
CHANGING THE LIGHT BULB
••
MMooddeell wwiitthh hhaallooggeenn bbuullbb
——
Remove the lighting port (fig. 1).
——
Change the G4-20W-12V halogen bulb.
——
Replace the bulb by repeating these steps
in reverse order.
Warning
Before carrying out any work, the power supply to the hood must be turned off, either
by unplugging it or by using the circuit breaker switch.
fig. 1
CLEANING THE OUTER SURFACES
To clean the outside of your hood, use soapy water,then rinse using clean water, drying with a
soft cloth.
NNeevveerr uussee mmeettaall ssccoouurriinngg ppaaddss,, aabbrraassiivvee pprroodduuccttss oorr eexxcceessssiivveellyy ssttiiffff bbrruusshheess..
••
38
5 / TROUBLESHOOTING
EN
The hood is not operating
effectively...
Ensure that:
• The selected motor speed is sufficient for the
quantity of smoke and vapours to be cleared.
• The kitchen is sufficiently ventilated to allow
for fresh air intake.
• The carbon filter is not worn (hood operating
in recycling mode).
The hood is
not working...
Ensure that:
• The power is not cut off.
• A speed has been selected.
The hood stopped
working
Ensure that:
• The power is not cut off.
• The single-pole cut-off device was not
activated.
SSOOLLUUTTIIOONNSSSSYYMMPPTTOOMMSS
Any maintenance on your equipment should be undertaken by:
- either your dealer,
- or another qualified mechanic who is an authorized agent for the brand appliances.
When making an appointment, state the full reference of your equipment (model, type and serial
number). This information appears on the manufacturer's nameplate attached to your equipment.
6 / AFTER-SALES SERVICE
EN
Loading...