7NF CESI data sheet ..................................................................................20
7.1NF CESI data sheet (for France only) ...............20
2
18/10/2012 - 300028214-001-02
Page 4
3
18/10/2012 - 300028214-001-02
Page 5
220 SHL
1Introduction
1.1Symbols used
1. Introduction
In these instructions, various danger levels are employed to draw the
user's attention to particular information. In so doing, we wish to
safeguard the user's safety, obviate hazards and guarantee correct
operation of the appliance.
DANGER
Risk of a dangerous situation causing serious physical
injury.
WARNING
Risk of a dangerous situation causing slight physical
injury.
1.2Abbreviations
1.3General
CAUTION
Risk of material damage.
Signals important information.
¼ Signals a referral to other instructions or other pages in the
instructions.
4 CFC: Chlorofluorocarbon
4 DHW: Domestic hot water
4 ICA: Impressed current anode
18/10/2012 - 300028214-001-02
1.3.1.Manufacturer's liability
Our products are manufactured in compliance with the requirements
of the various applicable European Directives. They are therefore
delivered with [ marking and all relevant documentation.
4
Page 6
1. Introduction
220 SHL
In the interest of customers, we are continuously endeavouring to
make improvements in product quality. All the specifications stated in
this document are therefore subject to change without notice.
Our liability as the manufacturer may not be invoked in the following
cases:
4 Failure to abide by the instructions on using the appliance.
4 Faulty or insufficient maintenance of the appliance.
4 Failure to abide by the instructions on installing the appliance.
1.3.2.Installer's liability
The installer is responsible for the installation and inital start up of the
appliance. The installer must respect the following instructions:
4 Read and follow the instructions given in the manuals provided
with the appliance.
4 Carry out installation in compliance with the prevailing legislation
and standards.
4 Perform the initial start up and carry out any checks necessary.
4 Explain the installation to the user.
4 If a maintenance is necessary, warn the user of the obligation to
check the appliance and maintain it in good working order.
4 Give all the instruction manuals to the user.
1.3.3.User's liability
To guarantee optimum operation of the appliance, the user must
respect the following instructions:
4 Read and follow the instructions given in the manuals provided
with the appliance.
4 Call on qualified professionals to carry out installation and initial
start up.
4 Get your installer to explain your installation to you.
4 Have the required checks and services done.
4 Keep the instruction manuals in good condition close to the
appliance.
This appliance is not intended to be used by persons (including
children) whose physcial, sensory or mental capacity is impaired or
persons with no experience or knowledge, unless they have the
benefit, through the intermediary of a person responsible for their
safety, of supervision or prior instructions regarding use of the
appliance. Care should be taken to ensure that children do not play
with the appliance.
To prevent hazardous situations from arising, if the mains lead is
damaged it must be replaced by the original manufacturer, the
manufacturer's dealer or another suitably skilled person.
5
18/10/2012 - 300028214-001-02
Page 7
220 SHL1. Introduction
1.4Homologations
1.4.1.Certifications
This product complies to the requirements to the european directives
and following standards:
Reference Standards: EN 50.081.1, EN 50.082.1, EN 55.014
18/10/2012 - 300028214-001-02
6
Page 8
2. Safety instructions and recommendations220 SHL
2Safety instructions and
recommendations
2.1Safety instructions
CAUTION
Before any work, switch off the mains supply to the
appliance.
2.2Recommendations
Have the installation regularly serviced to guarantee that it operates
correctly over time.
CAUTION
Never cut the power to the solar control system, even
during extended absences. The control system protects
the installation against overheating in summer when it is
running.
During extended absences, we recommend lowering the set point
temperature in the solar DHW calorifier to 50°C. When the user is
present, the set point must be set to 60°C.
CAUTION
Never drain the installation. Do not replace or add water
or solar fluid to the installation. These actions must be
carried out by a qualified technician.
CAUTION
Do not modify the control system parameters unless fully
conversant with them.
7
18/10/2012 - 300028214-001-02
Page 9
L000225-A
1
2
14
16
3
4
5
6
7
8
9
17
11
12
13
15
10
220 SHL3. Description
3Description
3.1Main parts
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Solar expansion vessel 12l
Thermostatic mixing valve for domestic hot water
Domestic hot water sensor
Solar regulator
Safety valve
Needle pressure gauge
Antithermosiphon valve operated by the spherical plug
valve
Solar circuit circulating pump
Glycol reservoir
Primary solar circuit filling and draining device
Primary solar coil sensor
Manual bleed degasser
Primary solar coil
Titan Active System anode
Plate exchanger on the primary boiler circuit
Domestic hot water circulating pump
17
Drain cock
3.2Technical specifications
3.2.1.Characteristics of the DHW calorifier
DHW tank 220SHL
Primary circuit (Heating water)
Maximum operating temperature°C95
Maximum operating pressurebar3
Primary circuit (Solar circuit fluid)
Maximum operating temperature°C135
Maximum operating pressurebar6
Exchanger capacityl8.4
Exchange surface
Secondary circuit (domestic water)
Maximum operating temperature°C95
18/10/2012 - 300028214-001-02
2
1.25
m
8
Page 10
3. Description
DHW tank 220SHL
Maximum operating pressurebar10
Water contentl220
Top up volumel85
Solar volumel135
Weight
Shipping weight (Foam coated domestic hot water tank) kg109
220 SHL
Performances related to the boiler type
Gas fired floor-standing condensing boiler
(1)
10/15 kW15 kW25 kW35 kW
Power exchangedkW15152832
Flow per hour (∆T = 35°C)
Specific flow (∆T = 30°C)
Draw-off capacity
(3)
(2)
(3)
Qp : Primary flow rate
(1) Depending on the country in which the boiler is installed
(2) Domestic cold water inlet: 10 °C - Domestic hot water outlet: 45 °C - Primary circuit (heating water): 80 °C
(3) Domestic cold water inlet: 10 °C - Domestic hot water outlet: 40 °C - Primary circuit (heating water): 80 °C - Calorifier temperature: 60 °C
Performances related to the boiler type
l/h370370690790
l/min20202426
l/10 mm200200240260
m3/h
0.450.450.801.00
Floor-standing condensing oil boiler
(1)
18 kW24 kW30 kW
Power exchangedkW182430
Flow per hour (∆T = 35°C)
Specific flow (∆T = 30°C)
Draw-off capacity
(3)
(2)
(3)
Qp : Primary flow rate
(1) Depending on the country in which the boiler is installed
(2) Domestic cold water inlet: 10 °C - Domestic hot water outlet: 45 °C - Primary circuit (heating water): 80 °C
(3) Domestic cold water inlet: 10 °C - Domestic hot water outlet: 40 °C - Primary circuit (heating water): 80 °C - Calorifier temperature: 60 °C
l/h440590740
l/min212425
l/10 mm210240260
m3/h
0.750.750.85
3.3Composition of the NF CESI solar systems packages (for France only)
Check the composition of the NF CESI solar system package against
the table below. The references and packages listed must be shown
on the invoice for the system sold by the installer.
A system is complete and functional according to the NF CESI mark
if all system references appear on the invoice. The system is
composed of the following elements:
4 A collector field with 1 or 2 solar collectors.
4 A boiler system (Modulens or OEnoviaGas Confort / OEnoviaFioul
Confort) + solar domestic hot water tank to which a solar station
is mounted in the factory, which includes a heating pump, an
expansion vessel and a Diemasol A / Oetrosol A control system.
4 The solar fluid that protects the installation from frost and
corrosion.
9
18/10/2012 - 300028214-001-02
Page 11
220 SHL3. Description
CESI SystemArray of collectorsDomestic hot water productionSolar fluid
NF CESI data sheet:
¼ See chapter: "NF CESI data sheet (for France
only)", page 20
18/10/2012 - 300028214-001-02
Page 15
L000224-A
1
2
3
220 SHL4. Operating the appliance
4Operating the appliance
4.1Putting the appliance into operation
CAUTION
Initial commissioning must be done by a qualified
professional.
CAUTION
During the heating process, a certain amount of water may
flow through the valve or safety unit, this is caused by
water expansion. This phenomenon is completely normal
and must in no event be hindered.
4.2Antifreeze protection
Once the DHW tank has been connected to the mains, the unit is
managed from the boiler control panel.
When in use, no direct action is needed on the DHW tank.
WARNING
Do not switch off the mains supply.
4 Antifreeze protection is guaranteed.
4 Protection of the tank against corrosion.
4.3Shutting down the solar control system
18/10/2012 - 300028214-001-02
CAUTION
Do not shut down power to the control system or drain the
heat-exchanging fluid.
14
Page 16
4. Operating the appliance220 SHL
The system is designed in such a way that no special precautions are
necessary during long periods of absence in summer.
The solar control system protects the installation from overheating.
15
18/10/2012 - 300028214-001-02
Page 17
220 SHL5. Checking and maintenance
5Checking and maintenance
5.1General instructions
CAUTION
4Maintenance operations must be done by a qualified
engineer.
4Only original spare parts must be used.
5.2Impressed current anode
No maintenance operations are required on an impressed current
anode.
CAUTION
The boiler control panel must be switched on to ensure
that the impressed current anode operates.
Failure to abide by this maintenance rule may damage the
domestic hot water calorifier and void its warranty.
5.3Safety valve or safety unit (DHW circuit)
The valve or safety assembly must be operated at least once a
month in order to ensure that it is operating correctly and to prevent
possible overpressure which would damage the DHW tank.
WARNING
Failure to comply with this maintenance rule may cause
deterioration of the DHW tank and the cancellation of the
guarantee.
WARNING
Only operate the valve (red head) on the DHW circuit. Do
not operate the valve (yellow head) on the solar circuit.
5.4Inspection and maintenance of the solar circuit
We recommend that you take out a maintenance contract
providing for an annual or biannual check of the fluid level,
the antifreeze protection, the pressure of the installation
and the expansion vessel, its tightness and its general
running.
18/10/2012 - 300028214-001-02
16
Page 18
5. Checking and maintenance220 SHL
5.5solar regulator
The solar control system is governed by the boiler control system. All
parameters and settings on the solar control system are managed
from the boiler control panel.
¼ Refer to the installation and maintenance instructions of the
boiler.
5.6Maintenance of the thermostatic mixing valve
The thermostatic mixer tap does not require any particular
maintenance.
5.7Cleaning the casing material
Clean the outside of appliances using a damp cloth and a mild
detergent.
17
18/10/2012 - 300028214-001-02
Page 19
220 SHL
6Warranty
6.1General
6.2Warranty terms
6. Warranty
You have just purchased one of our appliances and we thank you for
the trust you have placed in our products.
Please note that your appliance will provide good service for a longer
period of time if it is regularly checked and maintained.
Your fitter and our customer support network are at your disposal at
all times.
France: The following provisions are not exlcusive of the buyer being
able to benefit from the legal warranty stipulated in Articles 1641 to
1648 of the Civil Code.
Belgium: The following provisions regarding the contractual warranty
are not exclusive of the buyer being able to benefit from the legal
provisions applicable in Belgium regarding hidden defects.
Switzerland: The application of the warranty is subject to the terms
and conditions of sale, delivery and warranty of the company
marketing products.
Portugal: The following provisions do not adversely affect
consumers' rights, as laid down in Decree-Law 67/2003 of 8 April
amended by Decree-Law 84/2008 of 21 May, warranties relating to
sales of consumer goods and other implementing rules.
Other countries: The following provisions are not exclusive of the
buyer being able benefit from the legal provisions applicable
regarding hidden defects in the buyer's country.
Starting from the purchase date shown on the original fitter's invoice,
your appliance has a contractual guarantee against any
manufacturing defect.
The length of the guarantee is mentioned in the price catalogue.
The manufacturer is not liable for any improper use of the appliance
or failure to maintain or install the unit correctly (the user shall take
care to ensure that the system is installed by a qualified engineer).
In particular, the manufacturer shall not be held responsible for any
damage, loss or injury caused by installations which do not comply
with the following:
18/10/2012 - 300028214-001-02
4 applicable local laws and regulations,
4 specific requirements relating to the installation, such as national
and/or local regulations,
4 the manufacturer's instructions, in particular those relating to the
regular maintenance of the unit,
4 the rules of the profession.
18
Page 20
6. Warranty220 SHL
The warranty is limited to the exchange or repair of such parts as have
been recognised to be faulty by our technical department and does
not cover labour, travel and carriage costs.
The warranty shall not apply to the replacement or repair of parts
damaged by normal wear and tear, negligence, repairs by unqualified
parties, faulty or insufficient monitoring and maintenance, faulty
power supply or the use of unsuitable fuel.
Sub-assemblies such as motors, pumps, electric valves etc. are
guaranteed only if they have never been dismantled.
The legislation laid down by european directive 99/44/EEC,
transposed by legislative decree No. 24 of 2 February 2002 published
in O.J. No. 57 of 8 March 2002, continues to apply.
19
18/10/2012 - 300028214-001-02
Page 21
C003917-B
CARACTERISTIQUES CERTIFIEES:
CESI certifié
Efficacité
énergétique
A
c
(m²)*
U
c
(Wm-2K-1)*
U
s
(WK-1)*
C
s
(MJK-1)*
f
aux
*
DIETRISOL MODULENS 220-3
1.99
DIETRISOL MODULENS 220-5
4.1
PERFECTSUN OENOVIA 220-3
1.99
PERFECTSUN OENOVIA 220-5
4.1
INFORMATIONS COMPLEMENTAIRES:
VES 40: non applicable
* Pendant le période transitoire de détermination des performances thermiques seule l'efficacité
énergétique est disponible
All technical and technological information contained in these technical instructions,
as well as any drawings and technical descriptions supplied, remain our property
and shall not be multiplied without our prior consent in writing.
18/10/2012
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.