Dedicated Micros ECS2-16-1T, ECS2-08-1T, ECS2-16-2T Installation Manual

EcoSense

Installation and

Operation Guide

EcoSense

Contents

Introduction ....................................................................................... 3

Features ........................................................................................... 4

Important Safeguards ....................................................................... 6

Installing the Unit .............................................................................. 8

Installation ...................................................................................... 10

Accessing & Conguring the Unit ................................................... 18

Remote Control .............................................................................. 20

Main Menu ...................................................................................... 24

Navigating The Conguration Menus ............................................. 26

System ........................................................................................... 27

Display Settings .............................................................................. 51

Camera Settings ............................................................................. 57

Intelligent PTZ ................................................................................ 62

Record Settings .............................................................................. 75

Schedule ........................................................................................ 85

Alarm Settings ......................................................................................90

Network Settings .......................................................................... 106

Text ............................................................................................... 120

Archive ......................................................................................... 124

Diagnostics ................................................................................... 126

Event Search ................................................................................ 128

Unit Operation .............................................................................. 130

Operating the Viewer .................................................................... 131

Using the optional Keyboards

(DM/KBC1 & DM/KBC2) ............................................................... 156

Appendix A .................................................................................. 160

Appendix B ................................................................................... 167

Appendix C ................................................................................... 168

Appendix D ................................................................................... 170

Appendix E .................................................................................. 171

Appendix F ................................................................................... 172

Appendix G - Multicast ................................................................. 174

Appendix H - Monitor Output ........................................................ 175

Notes ............................................................................................ 176

Whilst every attempt is made to ensure these manuals are accurate and current, Dedicated Micros reserve the right to alter or

modify the specication of the machine described herein without prejudice.

Introduction

What is the…

EcoSense ?

The EcoSense from Dedicated Micros provides low cost multi channel recording with simultaneous playback and viewing; ideal for the cost conscious user who needs reliable, networked, high performance CCTV at an affordable price.

Available with 4, 8 or 16 camera inputs, all offering telemetry control, the EcoSense has built in Alarm functionality and onboard Activity detection software.

The state of the art touch sensitive front panel and the accompanying Infra-Red (IR) Remote Control make for simple, quick operation. Dedicated Micros trademark plug and play intuitive set-up, userfriendly interface with colour coded ‘softkeys’ and conguration menus common to both local monitor and web interface; help keep installation and operator training to a minimum.

The EcoSense offers a global record rate of up to 200pps (dependant on model) at CIF and can record up to 16 cameras (dependant on model) simultaneously in MPEG-4 or JPEG format. The Prole Record feature enables an operator to set different recording rates and resolutions across scheduled, normal and alarm modes for all cameras.

As standard, the unit includes internal storage with a CD/DVD-R Writer* and USB ports for external video archiving.

Among the many other features included as standard on the EcoSense are; multiway display, multiple language support, audio recording, activity detection and remote monitoring using NetVu ObserVer (utilising DM’s unique TransCoding capabilities to provide uent live and replay images). The EcoSense is undoubtedly the ideal product when high-performance video recording and transmission is required at an affordable cost.

For further information, please visit the website:

www.dedicatedmicros.com

or contact Dedicated Micros customer services in your region.

* Installed DVD writer only accepts -RW media.

EcoSense

from Software version 6.3 (8.0071) M4TP

Webpage version wp81.1(5036)ns

EcoSense

Features

• 4, 8 or 16 camera input options

• True global record rate of up to 200pps at CIF

• Simultaneous Live viewing and Recording

• D1/4CIF/2CIF/CIF record rate at 3/3/6/12pps per camera

• JPEG or MPEG-4 recording and transmission

• Touch sensitive front control panel

• Easy to use on-screen, colour coded softkeys

• Field serviceable hard drives

• Serial Telemetry support

• All DVR functions fully supported by Keyboard/IR Remote Control

• MultiMode Recording - Dynamically-switchable resolution, record-rate & compression (MPEG4/JPEG) per camera

• Single, Picture in Picture and Multiway displays

• Live and playback viewing locally and over Ethernet

• Built in activity detection

• Built in DVD writer* and USB ports for download of video archive to external ash memory

• Web pages provide easy remote conguration

• Alarm Inputs & Outputs

• Optional external keyboard available

* Not EcoSense 4

The unit has NetVu Connected technology built-in to ensure maximum compatibility with future developments in networked security. NetVu Connected technology enables the Unit to fully interact with other NetVu Connected compatible products from Dedicated Micros including the DV-IP Decoder, NetVu ObserVer and PDA Viewers. Providing interoperability between the worlds leading security companies, NetVu Connected uses industry standard networking protocols supported by a wide range of third party integration products and SDKs to ensure future on-going compatibility.

COMMON CONFIGURATION INTERFACE

A Common Conguration interface is displayed when the unit’s conguration screens are accessed locally at the unit or remotely via a web browser. This unied system ensures that the installer is familiar with the conguration screens irrespective of their location to the unit, minimising training and familiarisation time and increasing the speed of installation and alteration.

The Unit includes a unique colour-coded menu structure and onscreen Graphical User Interface (GUI). Context sensitive, the menu structure always represents the area of the menu the user is in, allowing them to quickly select the options and settings they need without having to trawl through menu pages and options. The colour coded buttons displayed on the monitor match those on the touch screen front panel and IR Remote Control, whilst control can also be conducted through an attached USB Mouse or supported Keyboard (DM/KBC1 / DM/KBC2).

Design of the manual

The manual has three parts:

1. Installation Shows details of how to install the unit and connect external devices.

2. Conguration Shows details of the unit’s menus.

3. Operation Shows quick reference details on how to control the unit.

The order and layout of these pages has been designed to help the setup process. It is recommended that the menus are edited sequentially (as they appear on the page), to enable accurate, easy and efcient setup.

EcoSense

Important Safeguards

Read Instructions

All the safety and operating instructions should be read before the unit is operated.

Power Sources

This unit should be operated only from the type of power source indicated on the manufacturer’s label.

Servicing

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualied service personnel.

Ventilation

Ensure unit is properly ventilated to protect from overheating. All the safety and operating instructions should be read before the unit is operated.

To prevent re or shock hazard, do not expose this equipment to rain or moisture. The lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user of this equipment that there are dangerous voltages within the enclosure which may be of sufcient magnitude to constitute a risk of electric shock.

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Lightning Strike

The unit has some in-built protection for lightning strike, however it is recommended that isolation transformers be tted to the system in areas where lightning is a common occurrence.

Regulatory Notes and FCC and DOC Information

(USA and Canadian Models Only)

Warning: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action. The user may nd the following booklet prepared by the Federal Communications Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems”.

This booklet is available from the US Government Printing Ofce, Washington, DC20402, Stock No. 004-000-00345-4.

This reminder is provided to call the CCTV system installer’s attention to Art. 820-40 of the NEC that provides guidelines for proper grounding and, in particular, species that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CE Mark

If this product is marked with the CE symbol it indicates compliance with all applicable directives.

Directive 89/336/EEC.

A ‘Declaration of Conformity’ is held at Dedicated Micros Ltd.,

1200 Daresbury Park, Daresbury, Cheshire, WA4 4HS, UK.

Laser

The unit supports an integrated CD/DVD writer, the following are additional warnings associated with installing and operating the CD/DVD writer, please pay particular attention to this information.

• Caution - Use of controls or adjustments or performance of procedures other than those specied herein may result in hazardous radiation exposure.

• To prevent exposure to laser emanations (harmful to the eyes), do not attempt to disassemble this unit.

Note: The writer only accepts -RW media.

EcoSense

Installing the Unit

Before you start

Check the contents of the box

The following items are included in the box:

Remove all items from the packaging and check the items listed below are present.

• EcoSense DVR (either 4, 8 or 16 input)

• IR Remote Control

• 12v DC Power Adaptor

• EcoSense Software CD

• Quick Start Guide

If any of these items are missing please contact Dedicated Micros Technical Support team.

Note: Before installing the unit, carefully read all Safety Instructions and the following information

on where the unit should be located.

Choosing a location for installation

• The unit is designed to be desk, shelf or rack mounted. Rack mounting brackets are available as an optional accessory.

• Ensure the unit is properly ventilated to protect from overheating.

• Ensure there is a 3cm gap on both sides of the unit.

• Ensure the IR receiver on the front of the unit faces the operator position, and is not more than 10 feet (3 metres) from the operator.

• Ensure the unit is not located anywhere it could be subject to mechanical shocks.

• The unit should be located in an area with low humidity and a minimum of dust. Avoid places like damp basements or loft spaces.

• If the unit is to be installed in a closed assembly, the maximum operating temperature must not exceed 40°C (104°F).

• Ensure there is reliable earthing of the mains outlet when tted to supply connections (other than direct connection to the branch circuit).

• Any branch circuit supplying the unit must be rated at 15Amps.

• It is recommended that an uninteruptable power source be connected to the unit in case of power failure (to ensure continuous operation of the unit).

Electrical Connections

Please ensure the following are available and have been tested prior to the installation:

• Mains point

• Network point

• Network cable

• Active video signals i.e. at least one working camera feed

• PC with CD ROM drive and connection to the same network as the DVR

(Recommended).

Quick Overview Of Default Record Settings

Units provide out of the box:

High performance recording on ALL cameras with minimal conguration.

Consistent recording duration and smooth motion video per camera regardless of the number of cameras connected.

Continuous 3pps MPEG4 recording on all cameras, on all channel variants (default out of the box).

Complete Flexibility

It is possible to set the unit’s record congurations based on specic priorities. feature allows different record rates and quality settings to be used for unset, set and override modes for all cameras. This can ensure event images are recorded at high quality, whilst normal ‘non event’ images are recorded at a reduced setting, minimising storage requirements.

With true global record rates of up to 200pps (PAL) and 240pps (NTSC), the unit offers recording of up to 3pps on each camera, out of the box, at a record duration of 7, 14 or 30 days (the default is 14 days).

Note: It is the Installer/Owner’s responsibility to ensure that the record duration is set to the

necessary requirements of the application.

The Prole Record

EcoSense

Installation

Front Panel connections

2 3

8 / 16 Input model

4 Input model

Data

CD/DVR Internal CD/DVR drive

Note: Installed DVD writer only accepts -RW media.

USB USB2.0 connector IR Infra-Red receiver for use with Remote Control

5 64

8 97

EXIT

2 3

5 64

8 97

Rear Panel connections

16 Input model

8 Input model

4 Input model

Video

VID1 to VID4/VID8/VID16 75Ω BNC composite video inputs 1V pk-pk MON A 75Ω BNC composite monitor output, 1V pk-pk MON B 75Ω BNC composite monitor output, 1V pk-pk S Video S Video Connection VGA VGA Monitor output

Audio

Audio IN 2x RCA (phono) socket, 8KHz/16KHz/22KHz sampling 75Ω input

impedance, 1V pk-pk

Audio OUT 2x RCA (phono) socket, line level <100Ω output impedance,1V

pk-pk amplication required

Data

SERIAL 1 RS-232 (3 wire) SERIAL 2 RS-485 (2 wire) USB 2x USB2.0 connectors

Note: No.USB connectors on the rear of the 4 channel unit. USB port located on front of unit.

NET RJ45 Ethernet network connector, 10/100 Mb/s Ethernet Network KBD RJ12 connector for use with KBC01 or KBC02 Keyboards

Note: The KBD connection is not available on the 4 channel unit.

Alarms and relays

ALARMS IN 25 way (female) D Type 24V 200mA 17 General Alarm Inputs Range of Alarm states are i. 0 – 800R = Short circuit ii. 800R – 2K = closed contact iii. 2k – 12k = open contact iv. > 12K = open circuit.

Note: 5 alarm inputs supported on 4 channel unit.

RELAYS Via 25 way (female) D Type rated at 24V 200mA 2 onboard light duty relay output (500mA@12V-48V Max)

Note: 1 relay output supported on 4 channel unit.

EcoSense

Power

POWER Input for 12v DC external power unit (supplied).

EcoSense

Installing the EcoSense Unit

This procedure shows the sixteen camera input version.

Step 1 Connecting Video

The unit supports up to 4, 8 or 16 connected Video Inputs (dependant on model) via the 75Ω BNC connectors. Connect cameras to the video inputs, starting from input 1.

5.12

Step 2 Monitor

The unit supports a main monitor via ‘Mon A’ and a spot monitor via BNC labelled ‘Mon B’. A monitor can also be connected via the S-Video or RGB Video outputs.

Step 3 Connecting Audio

The unit supports two channels of bi-directional audio, accessible through NetVu ObserVer. Connect the audio equipment to the phono sockets AUDIO IN and AUDIO OUT. The audio channel defaults to recording camera 1.

The following modes of operation are supported:

• Challenge – intruders from an RVRC.

• Listen – to local audio from a site at the RVRC.

• Record - local audio from a site with the video.

• Replay - all audio through a local Audio output (not supported when Audio out is used as a challenge/PA source)

Note: The Audio output can be congured as a challenge output or as a replay output.

Step 4 Connecting to the Network

EcoSense

The unit supports a 10/100Mbps auto-detecting network port. Use a CAT5 cable to connect the unit to the network.

EcoSense

Notes about IP Networks

Transmission Control Protocol/Internet Protocol - TCP/IP

The internet (and most other networks nowadays) use TCP/IP as the method of transporting data over a network. When data is transferred over an IP network it is broken up into segments (by the TCP) and sent as individual ‘packets’. Each packet is individually addressed (by the IP) with destination and source information, and can then be sent down a different path, and even a different sequence, across the network and reassembled at the other end. Data travelling on a network is referred to as ‘trafc’.

TCP/IP uses the client/server model of communication in which a client (computer) requests a service (camera image) by another machine (DVR) on the network. (In pure IP networks, the DVR requests a camera image from an IP camera on the network.) TCP/IP communication is primarily point-to-point, meaning each communication is from one point in the network to another point or host computer.

There are many higher level protocols that use TCP/IP as a tool for transportation, including HTTP, FTP, Telnet and SMTP

Dynamic Host Conguration Protocol - DHCP

Dynamic Host Conguration Protocol is a feature built into most routers. Routers control trafc on a network by sending IP packets down the most efcient available route to their destination. If you have a router on your network, then DHCP should be available to use. If it is not available, it may have been switched off. Check with the network administrator to establish if this is the case, and why it has been disabled/switched off. DHCP assigns Internet Provider (IP) addresses to devices on a network to ensure that the network makes the most efcient use of the limited number of IP addresses available to it. It removes the requirements for an administrator to keep track of all the IP addresses on a network and which number is assigned to which machine. DHCP keeps track of the network and assigns a free IP address to a unit as the unit connects to the network. However, it also means that a unit will not always have the same IP address when it connects to a network. The Internet is a network, and most Internet Service Providers utilise DHCP to connect users to the Internet.

Domain Name System - DNS

Computers use IP addresses to communicate with each other over a network. These IP addresses are 32 bit binary numbers expressed as four sets of three numbers (called octects), eg

565.898.785.124. These are not as easily remembered as the name of a server or a company. The Domain Name System is a distributed database stored on the Internet that translates host names into IP addresses, ie converts an easily remembered name or text string onto a four sets of three numbers that the computer can use to look up the site you are looking for (a useful analogy is a phone book for computers). This allows users to type in a humanly readable address and connect to a point on a network or the Internet.

Dynamic Domain Name System - DDNS

Dynamic DNS makes use of the DNS system described above. Given that DHCP means that the IP address of a device can change every time it is connected to a network or the Internet, and DNS can link an IP address to a recognisable string of text, Dynamic DNS allows a user to link a device to a string of text and force the database to be updated with the device’s new IP address whenever it connects to the Internet. Instead of a string of text being linked to an IP address in a static table, it is now linked to a DDNS server. Whenever the device connects to the Internet, it updates the DDNS table with its new IP address. ie it updates the computer phone book instantly on connection.

By default the unit is congured for DHCP i.e. the unit is automatically allocated an IP address from a network DHCP server.

DHCP works by assigning an IP address at initial connection to the network. It is possible however that this IP address can change without notication i.e. following power failure. It is therefore recommended that the unit either has a xed IP address allocated to it, or that DNS is utilised and a DNS name is set. A xed IP address can be assigned via the Conguration Menu pages:Network Settings->Network->IP Address. The DNS name of the unit can be edited on the System->System page. The DNS name is set by default as the serial number of the unit, which can be found on the base of the unit and on the packaging the unit arrived in.

When the unit is powered up, the network address can be found by viewing on a local monitor and navigating to Conguration Menu pages:System Settings->System->IP Address.

Refer to ‘Conguring The Unit’ for further guidance.

Step 5 Alarms / Relays

EcoSense

Alarms

The 4 channel unit supports 5 normally open/closed alarm inputs via the back panel, or one Global keyswitch input with camera specic inputs congurable as entry/exit alarms. All other units supports 17 normally open/closed alarm inputs via the back panel, or one Global keyswitch input with camera specic inputs congurable as entry/exit alarms.

Alarm/Relay Connector Pin Alarm Input Connection

1 - 17 1-17 18-21 Earth Common

Relays

The unit support up to two 24V 200mA relays

Relay Connector

Pins Connection

22 Relay 1 signal 23 Relay 1 ground 24 Relay 2 signal 25 Relay 2 ground

Note: The 4 channel unit supports one relay output.

EcoSense

Step 6 Connecting Serial Ports

Serial port 1 offers RS-232 connectivity, serial port 2 offers RS-485 connectivity.

Serial ports have two main uses:

1. Connecting twisted pair telemetry for PTZ cameras.

2. Debug operations.

RS232

RS485

5.16

6.1

Step 7 Connecting a Keyboard

The unit supports Dedicated Micro keyboards DM/KBC1 and DM/KBC2. Connect either of these keyboards via the KBD connector socket on the rear panel.

Note: The optional Keyboard is not supported on the 4 channel unit.

Note: Refer to the Unit Operation section of this manual for further guidance regarding the

supported keyboards.

Step 8 Connecting DM Oracle, 2060 & 2040 Domes

A DM Oracle, 2040 or 2060 Dome can be connected via RS485 twisted pair cabling.

The dome address should be set according to the camera number of unit (1-16).

Pin connections for RS485 connection to a Dennard dome on serial port 2 are:

Dome Cable Pin Connections

Yellow 1 TX+ Green 9 TX-

Step 9 Connecting Power

Connect the 12v DC power adaptor (supplied) to the unit and then to the wall socket, or to a fused spur connection. To be compliant with wiring regulations in some countries, an Alarm/Security device should be connected to a fused spur and not a wall outlet socket (check local regulations before installation).

EcoSense

Accessing & Conguring the Unit

The unit can be congured either on the local monitor or over the network using a PC with Internet Explorer or similar browser. Both have near identical menu interfaces.

Accessing the menus on a local monitor

Accessing the menus on a PC web browser

Default DNS Address

1. The Conguration pages can be displayed on a local monitor (connected to BNC Connector ‘Mon A’ on the rear of the unit). When connected, point the IR Remote Control at the front of the unit and press the MENU button.

Note: If the IR Remote Control does not open the conguration menus, press the DVR button to

make sure it is in DVR mode, then press the MENU button again.

The unit can be located on the network by using either the IP address or the DNS name (if DNS is available on the network). The IP address will be automatically assigned on startup if your network is DHCP capable. Most networks will be DHCP and DNS capable. The DNS name is set by default as the serial number of the unit, which can be found on the base of the unit and on the packaging the unit arrived in. This can be edited in the unit conguration pages.

For information on locating the unit’s IP address via a PC and serial port connection, refer to Appendix E.

It is recommended that a DNS (Domain Name Server) address be congured. Assigning a recognisable name can help a remote user to locate the unit.

If no System name is allocated to the unit, the default DNS address will be:

 machin_serial_number.yourdomain.com

• <machine serial number> is displayed in the System menu page and also on the underside of the unit.

• <yourdomain> is the name assigned to your DNS network.

The default DNS address can be renamed via the System->Attributes menu. Following renaming, the DNS address will be:

 yourname.yourdomain.com

• ’ yourname‘ is the name assigned via the Network menu.

• <yourdomain> is the name assigned to your

DNS network

Note: To activate an assigned DNS address, it will be necessary to reboot the unit. The unit can

be rebooted via System Settings:>Maintain-> Reset.

IMPORTANT: To set the time and date on the unit, navigate to System Settings->Time and Date.

Accessing the Conguration Webpages

To access the unit conguration webpages:

1. Launch Internet Explorer (or similar web browser package).

2. Type the URL for the unit (IP or DNS address).

Alternatively, the DNS address can be typed directly into the address bar of a web

browser.

Note: If the unit is subsequently assigned a xed IP address, its DNS address can no longer

be used

Note: The unit’s DNS address can be changed to something more memorable or meaningful than

its serial number by editing the System name option in the System conguration page.

3. The Opening menu page will be displayed.

EcoSense

6.13

Remote Control

The IR Remote Control offers all the control functionality required to navigate the menus.

Note: Not all buttons on the IR Remote Control are relevant for the Unit.

Key Button

Switches the Remote Control to ‘TV’

mode and sends codes understood by common TV sets.

Switches the Remote Control to ‘DVR’

mode. Note the DVR mode is the default mode of operation.

Use the Zoom button to zoom in/out

with a selected camera. Also used to zoom (x2) into Live or Playback images.

Use this button to cycle through

available cameras.

This button should be pressed (followed

by a numeric entry) to carry out auxiliary actions on a PTZ camera.

Press the Menu button to enter the

Conguration menus.

Press the Exit button to exit the

Conguration menus.

menu screens and accept changes. Also use for PTZ telemetry control

Use the Directional and OK buttons to navigate through the

of cameras.

Use the Softkeys (Red, Green, Yellow, Blue Purple) to directly access

the corresponding function displayed on the menu screen.

The Number pad should be used to select specic cameras and preset

positions when available.

Use the Playback buttons to interrogate recorded images. Use the LIVE

button to switch from Playback or menus to a LIVE display.

EcoSense

Using the IR Remote Control

Press the MENU button to access conguration menus via a connected local monitor. The menu will have a red indicator highlighting the rst option. Select a main menu heading to open a drop down list of further sub-options. Press the Down Directional button to highlight the next menu option, press OK to open the highlighted menu.

Press the Right Directional button to highlight the rst editable parameter on the screen.

Use the Left/Right/Up/Down Directional buttons to move between elds.

Select OK to start editing a eld (the option will be outlined in green).

Use the Up/Down Directional buttons to change the settings within an editable eld.

Use the OK button to accept a new setting. Use the coloured softkeys to select the accompanying colour option on screen i.e. red button to select the red option. To undo changes made to any menu, select the Refresh (Purple) option.

Note: See below for information on entering alpha-numeric data.

Using the Front Panel Interface

The Conguration and Viewer menus can be navigated and edited using the unit’s front panel interface (via a connected local monitor).

Navigate the menu tree via the Up/Down Directional buttons. When a menu is highlighted, open by pressing the OK button.

Use the Left/Right/Up/Down Directional buttons to move between elds.

Select OK to start editing a eld (the option will be outlined in green).

Use the Up/Down Directional buttons to change the settings within an editable eld.

Use the OK button to accept a new setting.

Use the colour bar (Red, Green, Yellow, Blue and Purple) to directly access the corresponding function displayed on the menu screen i.e. red panel to select the red option.

Note: See below for information on entering alpha-numeric data.

Entering Alpha-Numeric Data via a Local Monitor

Numeric or text data is entered using the on-screen Virtual Keyboard (Arrow Key Editor).

To display the Virtual Keyboard, navigate to the relevant text input box using the Directional buttons and double press the OK button twice on the IR Remote Control or Front Panel Interface. The Virtual Keyboard is displayed.

Use the Directional buttons to move between characters, use the OK button to select a character. Select ‘Submit’ to enter details, press ‘Cancel’ to exit without entering any text.

Alpha-numeric data can also be entered in either upper or lower case format by ‘multi-tapping’ a relevant button. For example, with the cursor located in the text entry window of the Virtual Keyboard, repeatedly tap button ‘2’ to cycle through the following characters: 2,A,a,B,b,C,c,2 etc.

To select one of these characters, simply stop tapping the button when the chosen character is displayed. The cursor will then progress, ready for the next character entry.

Note: A USB Keyboard (not supplied) can be connected via one of the USB ports on the unit. The

USB Keyboard can then be used to enter alpha-numeric data via the local menus.

Using a USB Mouse or the Webpages

Navigate the menus by clicking the tabs displayed on the left of the menu headings (on the menu tree). The rst option is highlighted with a red tab. Select a main menu heading to open a drop down list of further sub-options.

Highlight an editable eld by clicking on it directly.

If viewing pages locally, enter alpha numeric data via the Arrow Key Editor (see above). If viewing remotely, enter via the PC keyboard. If available, click on the drop down menus to select settings.

Note: A selected item in the drop down list will appear highlighted.

Navigating away from a page (clicking on a different option on the menu tree) will automatically save any changed settings. To undo changes made to any menu, select the Refresh (Purple) option.

Using a Supported Dedicated Micros Keyboards (DM/KBC1 & DM/KBC2)

The unit can also be controlled using an optional Dedicated Micros keyboard (except the 4 way unit). This is connected via the KBD connector on the rear of the unit and provides the same control functions as the I.R Remote Control.

Note: Refer to ‘Using the optional Keyboards (DM/KBC1 & DM/KBC2)’ for further guidance.

EcoSense

Main Menu

When rst accessing the unit, the main menu will be displayed. This menu allows access to the Conguration menus, the Viewer menus and also several Download options.

Note: The Download options will only be available if viewing remotely via an IP connection.

Select the Conguration menu tab to access the unit’s Conguration menus. Refer to ‘Navigating the Conguration Menus’ for further guidance.

Select the Viewer menu tab to access the unit’s Viewer function. Refer to ‘Unit Operation’ for guidance on the numerous Viewer features.

Select the Download menu tab to access the various Download sub-options. Select from:

• Product Manual Select to open an electronic version of the Installation & Operation Guide.

• ObserVer Manual Select to open an electronic version of the NetVu ObserVer User Guide. NetVu ObserVer is a free video management software package from Dedicated Micros. It allows users to seamlessly view distributed images from any ‘NetVu Connected’ product.

• NetVu ObserVer Select to download the NetVu ObserVer video management software.

• Java (JRE) Select to download the Java (JRE) software (from the unit). This software is required to successfully view Conguration and Viewer menus remotely.

IMPORTANT: By default, no Usernames and Passwords are required to access any of the

various menus. Usernames and Passwords can however be added to regulate access to the Conguration and Viewer menus. Refer to the ‘Display Settings-> User Accounts’ menu for information on establishing Usernames and Passwords.

EcoSense

Navigating The Conguration Menus

The menu tree provides access to the conguration menus.

The conguration pages are navigated using the menu tree (displayed on the left of each page). Selecting one of the menu options will display the relevant page. Associated sub-menus will then be available.

Relevant menus can also be accessed directly from other menu screens via the coloured softkey options shown at the base of each menu. The options available will depend on the menu being viewed. Select a softkey option by pressing either the corresponding button on the IR Remote Control (if viewing the menus locally), or by selecting the relevant option via the PC mouse (if viewing the webpages).

Note: Any changes made via the webpages are automatically saved when the page is closed. To

‘manually’ save changes, select the Save option.

System

The menus under the System Settings heading allow the unit’s core settings to be viewed, changed and the system software upgraded.

The System option displays details about the unit including the IP address, unit serial number, MAC address and software version.

The Status page displays information about the unit’s operating condition, shows how long the unit has been operating and the reason for the last reset. It also shows camera status and displays any failed cameras.

The Language page allows the system language to be set. The language can also be changed for the current session only.

The Time and Date page allows the unit time and date settings to be adjusted, including setting the timezone.

The Serial Ports page allows each of the two serial ports to be individually congured for one of a range of operations, including, debug, PPP and telemetry.

The Audio page shows the settings available for each of the audio channels and allows conguration of audio quality.

The Features page allows control of the different features that are available within the software including Email reporting, webcam support and control of the display resolution.

The Maintain page allows the current conguration to be saved, and for previously saved settings to be loaded. It also enables easy upgrade of the system software.

The PowerScript Mgmt page allows installed PowerScripts to be activated/deactivated on start-up.

EcoSense

Attributes

6.13

This menu shows the general information about the unit including the version of software installed, the unit’s serial number and the allocated DHCP IP address.

Product Descriptor Details the product model. Serial Number Identies the serial number of the specic unit. PCB Serial Number Displays the Printed Circuit Board serial number of the unit. Product Code Displays a code identifying the unit’s specication. Earliest Recording Displays the date/time of the earliest recording held on the unit. System Name This eld can be edited to allocate a name to the unit. This is

displayed when the unit is accessed via NetVu ObserVer and is sent when transmitting information to a Remote Video Response

Centres (RVRC). Number of Cameras Shows the number of camera channels on the unit. Global PPS Details the Global PPS (Pictures Per Second) recording rate for

all cameras. Video Storage Gbytes Highlights the available video storage capacity in Gigabytes. Video Standard Displays the video standard adopted by the unit i.e. PAL, NTSC. MAC Address This is the MAC address assigned to the unit. IP Address This is the IP address allocated to the unit. Sub Net This is the subnet of the network where the unit is located. Gateway This is the IP address of the default gateway (router) assigned by

the DHCP server.

Software Menu

EcoSense

Software Revision This identies the version of software the unit is running. Codec Revision This identies the codec version the unit is running. Webpage Revision This identies the webpage version the unit is running. Framestore Revision This identies the Framestore Revision the unit is running. PC Apps Revision This identies the revision archive of the Viewer and associated

PC Apps software. Boot Software Rev. Displays the infrastructure componentry software revision. Help Videos Rev. This identies the version of Help Videos installed on the unit.

Note: Refer to ‘Go To Viewer->Help Videos’ for guidance on viewing the imbedded Help Videos.

Applet Version This identies the applet version installed on the unit

Note: Refer to ‘Display Settings->Viewer Defaults’ for guidance on using a remote applet (this can

lessen load times when accessing multiple DVRs/Servers).

System (Red) Select this option to return to the System menu.Software Revision

This identies the version of software the unit is running.

EcoSense

Unit Status

This menu details information regarding the status of the unit, notably the total time the unit has been operating and the time since its last reset.

Time since last reset Details the time since the unit was last reset. Total running time Details the total time the unit has been operational. Reset code The last reset code used is displayed. Restart reason The reason for the last restart is displayed i.e. Controlled

User Reset. Codec Two codecs are installed within the unit. Cameras Shows which cameras are assigned to the displayed codec. Connected Those camera channels with cameras connected will be

highlighted light green. Those not in use will appear dark green. Recording Those camera channels that are currently recording are

highlighted light green. Those not recording will appear

dark green. Cam Status Those camera channels where the connection is deemed to

be functioning correctly will be highlighted light green. Those

deemed to have failed will appear red. Camera channels with no

connected camera will appear dark green.

+ 150 hidden pages

Dedicated Micros ECS2-16-1T, ECS2-08-1T, ECS2-16-2T Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual