Page 1
Installation Guide
Intelligent Security & Fire Ltd
Page 2
2
NV4
Whilst every attempt is made to ensure these manuals are accurate and current, Dedicated Micros reserve the right to alter or
modify the specication of the machine described herein without prejudice.
Features ........................................................................................... 4
Important Safeguards ....................................................................... 6
Installing the Unit .............................................................................. 8
Installation ...................................................................................... 10
Closed IPTV ................................................................................... 19
Conguring the Unit ........................................................................21
Remote Control .............................................................................. 23
Main Menu ......................................................................................25
Navigating The Conguration Menus ............................................. 27
System Settings ............................................................................. 30
Closed IPTV .................................................................................. 57
Console Settings ............................................................................ 66
Camera Settings .............................................................................82
Record Settings .............................................................................. 97
Schedule .......................................................................................110
Alarm Settings .................................................................................... 115
Network Settings .......................................................................... 132
Features & Text ............................................................................ 149
Analytics & Third Party IP Cameras ............................................. 150
Installing An Advanced Feature License .......................................... 151
Archive ......................................................................................... 170
Oracle Dome Conguration .......................................................... 172
Unit Operation .............................................................................. 188
Operating the Viewer ....................................................................189
Using the optional keyboards ....................................................... 213
Appendix A - Closed IP Conguration Scenarios ......................... 217
Appendix B - Pinouts .................................................................... 222
Appendix C- Remote Control Codes ............................................ 223
Appendix D - User Activity Logging .............................................. 225
Appendix E -
Locate IP Address (Serial)
...................................... 226
Appendix F - Videolan VLC .......................................................... 227
Appendix G - Third Party IP Camera ............................................ 228
Appendix H - Monitor Output ........................................................ 229
Appendix I - Status Pages ............................................................ 230
Appendix J - Unit Specication .....................................................240
Contents
Intelligent Security & Fire Ltd
Page 3
3
Installation Guide
Introduction
What is the…
NV4 ?
A powerful hybrid DVR/NVR, the NV4 combines all the benets of a DVR with the feature set of a high
performance embedded NVR and offers multiple channels of IP and Analogue video, HDMI main monitor
support, on-board analytics, help videos and Oracle Dome conguration.
The NV4 is a true hybrid DVR/NVR. Offering up to 32 camera connections in a combination of analogue
or IP (including 3rd party IP cameras). The NV4 offers 16 analogue camera connections, with the balance
of the 32 camera connections being made up by IP camera streams - even HD cameras.
Closed IPTV
Dedicated Micros’ ground breaking Closed IPTV solution makes deploying an IP Video, CCTV system
safe, secure and simple. Combining patent-pending innovation with zeroconf networking technology,
Closed IPTV automatically allocates IP addresses to IP cameras by physical port. In this way the system
is completely deterministic, creating rewalls and monitoring IP connections by individual network ports so
they cannot be hacked or intercepted. This ground breaking solution provides a very simple and secure
answer to IP Video, meaning that no prior knowledge of IP networking is required. Sophisticated and
Dependable network security can be achieved with a single click.
Leverage the powerful embedded NVR within the NV4 to incrementally grow your camera estate.
Combine your existing installed analogue cameras with secure IP and HD cameras from a Closed IPTV
system. Up to 32 camera streams can be connected enabling analogue and secure IP cameras to be
shown together seamlessly. All that is required to take the next leap in video surveillance technology is
Dedicated Micros unique Layer 3 Enhanced CCTV Switch and NetVu Connected IP cameras.
The NV4 includes powerful new codecs and the Turbo Mode feature that ensures maximum per camera
performance. Enabling Turbo Mode can effectively double the units performance allowing real-time
recording at double the resolution simply with the press of a button.
The NV4 can connect to up to 32 cameras - offering a blend of analogue and IP connections. Each
camera can offer real-time viewing, recording and playback simultaneously.
For further information, please visit the website:
www.dedicatedmicros.com
or contact customer services in your region.
from Software version 6.6 (8.0073) M3UP
Webpage version wp81.1(5110)ns
Intelligent Security & Fire Ltd
Page 4
4
NV4
Features
• 16 analog camera input options
• Telemetry support (Coax & Serial)
• All DVR functions fully supported by Keyboard/IR Remote Control/Front Panel
• Scalable recording settings
• MultiMode Recording - Dynamically-switchable resolution, record-rate & compression
(MPEG4/JPEG/H264) per camera
• JPEG, MPEG-4 or H264 recording and transmission
• Up to 6TB of on-board storage
• HDMI monitor support
• I.P Camera support
• Web pages provide easy remote conguration
• Single, Picture in Picture and Multiway displays
• Live and playback viewing locally and over Ethernet
• Built in activity detection
• On-board Help videos
• Built in CD-R/DVD-R writer and USB ports for download of video archive to external
ash memory
• Point&go telemetry control and Absolute Positioning
• Alarm Inputs & Outputs
• Easy to use on-screen, colour coded soft keys
• Front panel interface
• Text support and text search features ideal for retail installations
• Optional external keyboard available
• Conguration via USB mouse and USB QWERTY keyboard
• BS8418 compliant
The unit has NetVu Connected technology built-in to ensure maximum compatibility with future
developments in networked security. NetVu Connected technology enables the Unit to fully interact with
other NetVu Connected compatible products from Dedicated Micros including the DV-IP Decoder, NetVu
ObserVer and PDA Viewers. Providing interoperability between the worlds leading security companies,
NetVu Connected uses industry standard networking protocols supported by a wide range of third party
integration products and SDKs to ensure future on-going compatibility.
Closed IPTV
Dedicated Micros’ ground breaking Closed IPTV solution makes deploying an IP Video, CCTV system
safe, secure and simple. Combining patent-pending innovation with zeroconf networking technology,
Closed IPTV automatically allocates IP addresses to IP cameras by physical port.
In this way the system is completely deterministic, creating rewalls and monitoring IP connections by
individual network ports so they cannot be hacked or intercepted. This ground breaking solution provides
a very simple and secure answer to IP Video, meaning that no prior knowledge of IP networking is
required.
Sophisticated and Dependable network security can be achieved with a single click.
Intelligent Security & Fire Ltd
Page 5
5
Installation Guide
COMMON CONFIGURATION INTERFACE
A Common Conguration interface is displayed when the unit’s conguration screens are accessed locally
at the unit or remotely via a web browser. This unied system ensures that the installer is familiar with the
conguration screens irrespective of their location to the unit, minimising training and familiarisation time
and increasing the speed of installation and alteration.
The Unit includes a unique colour-coded menu structure and on screen Graphical User Interface (GUI).
Context sensitive, the menu structure always represents the area of the menu the user is in, allowing
them to quickly select the options and settings they need without having to trawl through menu pages and
options. The colour coded buttons displayed on the monitor match those on the IR Remote Control, whilst
control can also be conducted through an attached USB Mouse or supported Keyboard (DM/KBC1 / DM/
KBC2).
Point&go provides the user with easy to use, fast, accurate telemetry control via an attached monitor.
With no need for a telemetry keyboard, users are able to use Pan & Tilt control of a Dedicated Micros
Oracle Dome simply by clicking an area of the monitor. The camera will instantly respond, positioning the
selected area in the middle of the screen, ideal for tracking movement through a scene.
MAP
Users can now navigate around their CCTV installation using a graphical map. Selecting the relevant
camera from the map will instantly connect the user to that cameras image stream. With the ability to
load bespoke map images and oor plans to reect their installations, the Maps feature is ideal for quickly
identifying camera locations around a site or CCTV network.
Turbo Mode
Turbo mode allows video images from any analogue camera or 3rd Party IP recoded camera to
be recorded and streamed at the maximum possible rate without the need to congure individual
settings. Turbo mode must be set Globally and will result in MPEG record rates of 12.5pps@4CIF and
25pps@2CIF/CIF/QCIF.
Design of the manual
The manual has three parts:
1. Installation Shows details of how to install the unit and connect external devices.
2. Conguration Shows details of the unit’s menus.
3. Operation Shows quick reference details on how to control the unit.
The order and layout of these pages has been designed to help the setup process. It is recommended
that the menus are edited sequentially (as they appear on the page), to enable accurate, easy and
efcient setup.
Intelligent Security & Fire Ltd
Page 6
6
NV4
Important Safeguards
Read Instructions
All the safety and operating instructions should be read before the unit is operated.
Power Sources
This unit should be operated only from the type of power source indicated on the manufacturer’s label.
Servicing
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards.
Refer all servicing to qualied service personnel.
Ventilation
Ensure unit is properly ventilated to protect from overheating.
All the safety and operating instructions should be read before the unit is operated.
To prevent re or shock hazard, do not expose this equipment to rain or moisture. The lightning ash with
arrowhead symbol within an equilateral triangle is intended to alert the user of this equipment that there
are dangerous voltages within the enclosure which may be of sufcient magnitude to constitute a risk of
electric shock.
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Lightning Strike
The unit has some inbuilt protection for lightning strike, however it is recommended that isolation
transformers be tted to the system in areas where lightning is a common occurrence.
Regulatory Notes and FCC and DOC Information
(USA and Canadian Models Only)
Warning: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
If necessary, the user should consult the dealer or an experienced radio/television technician for
corrective action. The user may nd the following booklet prepared by the Federal Communications
Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems”.
This booklet is available from the US Government Printing Ofce, Washington, DC20402,
Stock No. 004-000-00345-4.
This reminder is provided to call the CCTV system installer’s attention to Art. 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, species that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
Intelligent Security & Fire Ltd
Page 7
7
Installation Guide
CE Mark
If this product is marked with the CE symbol it indicates compliance with all applicable directives.
Directive 89/336/EEC.
A ‘Declaration of Conformity’ is held at Dedicated Micros Ltd.,
1200 Daresbury Park, Daresbury, Cheshire, WA4 4HS, UK.
Laser
The unit supports an integrated CD-R/DVD-R writer, the following are additional warnings associated with
installing and operating the CD-R/DVD-R writer, please pay particular attention to this information.
• Caution - Use of controls or adjustments or performance of procedures other than those
specied herein may result in hazardous radiation exposure.
• To prevent exposure to laser emanations (harmful to the eyes), do not attempt to
disassemble this unit.
Intelligent Security & Fire Ltd
Page 8
8
NV4
Installing the Unit
Before you start
Check the contents of the box
The following items are included in the box:
Remove all items from the packaging and check the items listed below are present.
• NV4 NVR
• IR Remote Control
• Power Leads
• IR Extender Lead
• NV4 Software/Documentation CD
• Mouse
• Rack Mounting brackets
• RS485 Telemetry Adaptor
• Quick Start Guide
If any of these items are missing please contact Dedicated Micros Technical Support team.
Note: Before installing the NV4 DVR, carefully read all Safety Instructions and the following information
on where the unit should be located.
Choosing a location for installation
• The NV4 is designed to be desk, shelf or rack mounted. Rack mounting brackets are
available as an optional accessory.
• Ensure the NV4 unit is properly ventilated to protect from overheating.
• Ensure there is a 3cm gap on both sides of the unit.
• Ensure the IR receiver on the front of the unit faces the operator position, and is not more
than 10 feet (3 metres) from the operator. An IR Remote Control Extender is also available.
• Ensure the unit is not located anywhere it could be subject to mechanical shocks.
• The unit should be located in an area with low humidity and a minimum of dust. Avoid places
like damp basements or loft spaces.
• If the unit is to be installed in a closed assembly, the maximum operating temperature must
not exceed 40°C (104°F).
• Ensure there is reliable earthing of the mains outlet when tted to supply connections (other
than direct connection to the branch circuit).
• Any branch circuit supplying the unit must be rated at 15Amps.
• It is recommended that an uninteruptable power source be connected to the unit in case of
power failure (to ensure continuous operation of the unit).
Intelligent Security & Fire Ltd
Page 9
9
Installation Guide
Electrical Connections
Please ensure the following are available and have been tested prior to the installation:
• Mains point
• Network point
• Network cable
• Active video signals i.e. at least one working camera feed
• PC with CD ROM drive and connection to the same network as the NVR (Recommended).
Quick Overview of NV4 Record Settings
The NV4 provides as default:
Consistent recording duration and smooth motion video per camera regardless of the number of cameras.
Default record settings at MPEG4 6.25pps (at 2CIF), JPEG 3pps (at 2CIF) and MultiMode recording at
MPEG4 6.25pps (at 2CIF), JPEG 6.25pps (at 2CIF).
Complete Flexibility
The advanced record menu can be used to congure individual cameras to suit specic requirements
e.g. Entry/Exit routes. Various storage sizes are available dependent on the combination of the number of
cameras, the storage options and record rates selected.
MultiMode Recording
The unit supports MultiMode recording, which is a storage technology developed by Dedicated Micros.
This offers the ability to set different recording rates, resolutions and compression formats across
scheduled, normal and alarm modes for each individual camera.
By varying the quality, bit rate and le size of the recorded images, the MultiMode function can increase
recording capabilities of the unit.
MultiMode offers:
Ability to set different recording resolutions.
Ability to set and switch MPEG or JPEG compression recording as required.
Ability to set PPS recording rate per camera.
Dynamically switchable resolution when switching from Normal to Event recording.
Dynamically switchable compression between MPEG4 and JPEG from Normal to
Event recording.
Intelligent Security & Fire Ltd
Page 10
10
NV4
Installation
Front Panel connections
Data
DVD-R Internal CD/DVD-R drive (located under hinged ap)
USB USB2.0 connector (located under hinged ap)
LED Green - Unit working normally
No LED - Power Failure
Live - Unit is in Live mode when lit.
Play -Unit is in Playback mode when lit.
Spot - Spot (MON B) monitor is being controlled
Record - Unit is recording video to the internal hard disk.
Rear Panel connections
16 Input model
Video
VID1 to VID16 75Ω BNC composite video input, 1V pk-pk with loop through 1V
MON A 75Ω BNC composite monitor output, 1V pk-pk
MON B Spot Monitor output
HDMI 1 High-Denition Multimedia Interface connector (DVR Mode : Spot,
Decoder mode : Congurable Main)
HDMI 2 High-Denition Multimedia Interface connector (DVR Mode : Main,
Decoder mode : Congurable Main)
Audio
AUX AUD IN x2 3.5mm (phono) socket, 8KHz/16KHz/22KHz sampling 75Ω input
impedance, 1V pk-pk
AUX AUD OUT x2 3.5mm (phono) socket, line level <100Ω output impedance,1V pk-pk
amplication required
Intelligent Security & Fire Ltd
Page 11
11
Installation Guide
Data
SERIAL 1 RS-232 (3 wire & 9 wire)
SERIAL 2 RS-232 (3 wire & 9 wire)
SERIAL 3 (PTZ) RS-485 (2 wire & 4 wire)
SERIAL 4 (PTZ) RS-485 (2 wire & 4 wire)
USB 2x USB2.0 connectors
IR Infra-Red Input connector for IR Remote Control Extender
ETH-A RJ45 Ethernet network connector, 10/100 Mb/s Ethernet Network
ETH-B RJ45 Ethernet network connector, 10/100/1000 Mb/s Ethernet Network
KBD RJ12 connector for use with Dedicated Micros telemetry
keyboards (KBC1, KBC2)
EXP RJ12 expansion port
SATA 2x E-Sata port available for storage expansion
Alarms and relays
ALARMS IN Via 25-way (female) D Type 24V 200mA
20 general alarm inputs
Range of Alarm states are:
i. 0 – 800R = Short circuit
ii. 800R – 2K = closed contact
iii. 2k – 12k = open contact
iv. > 12K = open circuit
RELAYS Via 9-way (female) D Type rated at 24V 200mA
4 onboard light duty relay output (500mA@ 12V-48V Max)
Power
POWER IEC mains power socket & switch
Intelligent Security & Fire Ltd
Page 12
12
NV4
Installing the NV4 Unit
This procedure shows the sixteen camera input version. There are a number of Closed IPTV installation
scenarios in Appendix A.
Step 1 - Connecting to the Network
USB
NET 1
VID 1 VID 2 VID 3
VID 13
VID 8
VID 6VID 4 VID 5 VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15
POWER
IR
MON A
AUDIO
B
B
B
B
B
B
B
B
B
B
B
B
B
B
ALARMS
IR
EXP
KBD
RELAYS
HDMI
B
VID 16
B
AUDIO
IN
OUT
OUT
A
B
SERIAL 2
SERIAL 3 PT
Z
SERIAL 1
SERIAL 4 PTZ
SATA
The unit supports two auto-detecting network port, ETH-A is 10/100MBps, EHT-B is 10/100/1000MBps. If using,
Closed IPTV, use a CAT5 cable to connect port ETH-A of the Layer 3 Enhanced CCTV Switch to the network port
labelled ‘NET’. The Layer 3 Enhanced CCTV Switch will provide connection to the general corporate network if
required. If not utilising Closed IPTV, connect to a normal switch.
Layer 3 Enhanced CCTV Switch connection (Closed IPTV only)
By default the unit is congured for DHCP i.e. the unit can automatically be allocated an IP address from
a network DHCP server.
DHCP works by assigning an IP address at initial connection to the network. It is possible however that
this IP address can change without notication i.e. following power failure. DNS (Dynamic Name Service)
allows the unit to be assigned a meaningful name which can be used to reference the unit instead of
an IP address. This will remain constant in the event that the DHCP assigned IP address changes. If
you do not wish to assign a DNS name, a xed IP address can be assigned via the Conguration Menu
pages:Network Settings->Network->IP Address.
When the unit is powered up, the network address can be found by viewing on a local monitor and
navigating to Conguration Menu pages:System Settings->System->IP Address.
Refer to ‘Conguring The Unit’ for further guidance on locating the unit’s IP address and for details of the
default DNS (Domain Name Service) address.
Important: The Closed IPTV NV4 unit must be in Congure mode to nd any existing units on the
network with addresses in the range it can automatically assign. It can then give suitable IP
addresses for new cameras, avoiding potential IP address clashes.
Intelligent Security & Fire Ltd
Page 13
13
Installation Guide
Step 2 - Connecting Video
VID 1 VID 2 VID 3
VID 13
VID 8
VID 6VID 4 VID 5 VID 7
VID 9 VID 10 VID 12VID 11 VID 14 VID 15
POWER
IR
MON A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
ALARMS
IR
EXP
KBD
RELAYS
HDMI
B
VID 16
B
O
IN
OUT
OUT
A
B
SERIAL 2
SERIAL 3 PTZ
SERIAL 1
SERIAL 4 PTZ
SATA
The NV4 supports up to 16 connected analog Video Inputs via the 75Ω BNC connectors. Connect
cameras to the video inputs, starting from input 1.
Note: In a Closed IPTV application, channels can be utilised by the Analogue cameras connected
to BNC sockets on the back of the unit OR by IP cameras connected to the Closed IPTV
camera ports on the Layer3 Enhanced CCTV Switch. If an IP source is plugged into a channel
occupied by a BNC connection, the BNC will take priority and possess the channel, whilst the
IP connection will be added to an un-allocated list (refer to ‘Closed IPTV Camera Allocation’),
allowing it to be tied to an available channel through the conguration pages.
The NV4 has 16 channels that can be used for analogue input. Analogue channels can also be used
as recode channels for 3rd party IP inputs or they can also be used to remote codec NetVu Connected
capable encoders. The available inputs are;
Analogue Recode/IP NetVu Connected
3rdParty
NV4 8ch 8 or 8 or 32 NetVu connections
NV4 8ch 8 or 8 and 24 NetVu connections
NV4 16ch 16 or 16 or 32 NetVu connections
NV4 16ch 16 or 16 and 16 NetVu connections
Note: The ‘Restrict public access (Eth B)’ setting (Closed IPTV-> Settings must be enabled if using
Oracle IP domes in a Closed IPTV environment. Dedicated Micros strongly recommends
enabling this setting once conguration is complete even if Oracle IP
Domes are not used in the conguration.
5.12
Step 3 - Monitor
VID 13
VID 8
VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15
POWER
B
B
B
B
B
B
B
B
ALARMS
IR
EXP
KBD
RELAYS
HDMI
B
VID 16
B
Intelligent Security & Fire Ltd
Page 14
14
NV4
The unit supports a main monitor via ‘HDMI 1’ and BNC ‘A’. A spot monitor can be connected via BNC ‘B’.
The unit will boot up in SAFE mode. This allows viewing on both composite and HDMI (if HDMI is
connected during BOOT UP).
Important: Safe mode is suboptimal, and an appropriate display setting should be congured in the
Viewer Defaults Conguration pages.
Step 4 - Connecting Audio
USB
NET 1
VID 1 VID 2 VID 3
VID 13
VID 8
VID 6VID 4 VID 5
VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15
POWER
IR
MON A
AUDIO
B
B
B
B
B
B
B
B
B
B
B
B
B
B
ALARMS
IR
EXP
KBD
RELAYS
HDMI
B
VID 16
B
AUDIO
IN
OUT
OUT
A
B
SERIAL 2
SERIAL 3 PTZ
SERIAL 1
SERIAL 4 PTZ
SATA
The NV4 supports two channels of bi-directional audio, accessible through NetVu ObserVer. Connect
the audio equipment to the phono sockets AUDIO IN and AUDIO OUT. The audio channel defaults to
recording camera 1.
The following modes of operation are supported:
• Challenge – intruders from an RVRC.
• Listen – to local audio from a site at the RVRC.
• Record - local audio from a site with the video.
• Replay - all audio through a local Audio output (not supported when
Audio out is used as a challenge/PA source).
Note: The Audio output can be congured as a challenge output or as a replay output.
Step 5 - Relays
VID 13
VID 8
VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15
POWER
B
B
B
B
B
B
B
B
B
RELAYS
HDMI
B
VID 16
B
RELAYS
Pin 1 Relay 1 Signal
Pin 2 Relay 2 Signal
Pin 3 Relay 3 Signal
Pin 4 Relay 4 Signal
Pin 5
Pin 9
Relay 4 Signal
Pin 8
Relay 3 Signal
Pin 7
Relay 2 Signal
Pin 6
Relay 1 Signal
View on
rear of
unit
Note: HDMI shown removed.
The NV4 supports up to ve 24V 200mA relays.
Intelligent Security & Fire Ltd
Page 15
15
Installation Guide
Relay Connector
Pins Connection
1 & 6 Relay 1 signal
2 & 7 Relay 2 signal
3 & 8 Relay 3 signal
4 & 9 Relay 4 signal
Step 6 - Alarms
VID 13VID 6VID 4 VID 5 VID 7 VID 9 VID 15
POWER
B
B
B
B
ALARMS
IR
HDMI
VID 16
View on
rear of
unit
VID 9
V
rear of
unit
V
Pin 2 DTX
Pin 4 DTX
Pin 6 DTX
Pin 8 DTX
Pin 10 DTX
Pin 12 DTX
Pin 1 DTX
Pin 3 DTX
Pin 5 DTX
Pin 7 DTX
Pin 9 DTX
Pin 11 DTX
Pin 13 DTX
Pin 25 Earth
Pin 23 Earth
Pin 21 Earth
Pin 19 DTX
Pin 17 DTX
Pin 15 DTX
Pin 24 Earth
Pin 22 Earth
Pin 20 DTX
Pin 18 DTX
Pin 16 DTX
Pin 14 DTX
ALARMS
The NV4 supports 20 normally open/closed tamper proof alarm inputs, or one Global keyswitch input with
camera specic inputs congurable as entry/exit alarms. The alarms support tamper proof detection using
1k in line and 5K end of line resistance. The unit detects short circuit, open circuit and contact closure.
This functionality is part of the advanced alarms supported on NetVu Connected products and includes
features required for Central Monitoring. It is compatible with the British Standard BS8418.
Relay Connector
Pin Alarm Input Connection
1 - 20 1-20
21-25 Earth Common
Intelligent Security & Fire Ltd
Page 16
16
NV4
End Of Line Circuitry
The following describes the EOL tamper alarms circuitry needed when EOL has been congured. There
should be two resistive values within the tamper alarm circuitry. These must be located inside the alarm
device (furthest point from the unit).
The alarm state could be Normally Open or Normally closed however the tamper states are the same for
both settings.
Open, the resistive value is 6.8K ohms (1K + 5.6K).
Closed, the resistive value is 1K ohms, as the circuit does not see the 5.6K ohm resistor.
Open Circuit Tamper, the resistive value is innity as the circuit has been cut and
therefore is ‘open’.
Short Circuit Tamper, the resistive value is 0 Ohms.
Step 7 - Connecting Serial Ports
Serial ports have three main uses:
1. Connecting twisted pair telemetry for PTZ cameras.
2. Providing text data recorded with the video e.g. Point of Sale.
3. Debug operations.
Note: Telemetry cameras should be connected to Serial 3 and 4. Text data can be retrieved from any
serial port.
Intelligent Security & Fire Ltd
Page 17
17
Installation Guide
RS232
RS485
6.1
Step 8 - Connecting a Keyboard
The NV4 supports Dedicated Micro keyboards DM/KBC1 and DM/KBC2. Connect either of these
keyboards via the KBD connector on the rear panel.
Note: Refer to the Unit Operation section of this manual for further guidance regarding the supported
keyboards.
Step 9 - Connecting DM Oracle, 2060 & 2040 Domes
IMPORTANT: The ‘Restrict public access (Eth B)’ setting (Closed IPTV-> Settings must be enabled if
using Oracle IP domes in a Closed IPTV environment.
A DM Oracle, 2040 or 2060 Dome can be connected via either co-axial telemetry or RS485 twisted pair. If
using co-axial the address switches should be set as:
Blue switch - F
Yellow switch - D
If the dome is being connected using RS485, the dome address should be set according to the camera
number of the NV4.
Pin connections for RS485 connection to a Dennard dome on serial port 3/4 are:
Dome Cable NV4 Serial Connector
Yellow 1 TX+
Green 9 TX-
Intelligent Security & Fire Ltd
Page 18
18
NV4
Step 10 - Connecting Power
VID 13
VID 12
VID 14 VID 15
POWER
B
B
B
B
S
IR
RELAYS
HDMI
B
VID 16
B
The NV4 has an internal power supply unit. Connect the mains lead to the unit and then to the wall
socket, or to a fused spur connection. To be compliant with wiring regulations in some countries, an Alarm/
Security device should be connected to a fused spur and not a wall outlet socket (check local regulations
before installation).
Intelligent Security & Fire Ltd
Page 19
19
Installation Guide
Closed IPTV
Closed IPTV Camera Allocation
Analogue channels can be utilised by the BNC connections on the back of the unit OR by the sockets
on the Layer 3 Enhanced CCTV Switch. If an IP source is plugged into a channel occupied by a BNC
connection, the BNC will take priority and possess the channel, whilst the IP connection will be added to
an unassigned list, allowing it to be tied to an available channel through the conguration pages.
Individual cameras should be connected in sequential order, i.e. connect the rst camera to port number
1 on the Layer 3 Enhanced CCTV Switch. When this connection is registered by the NVR, it will display
a notication on the Main Monitor showing the recognised details of the new video source, including
resolution, name and MAC address. There will also be a notication if a camera is disconnected.
Multi channel encoder camera allocation (DV-IP NV1)
A NetVu Connected multi-channel server can be can be added to any of the camera ports as a video
source. The available channels are then allocated as the Layer 3 Enhanced CCTV Switch detects video
sources on the NetVu Connected multi-channel server and allocates them to consecutive Port Free
channels, starting at the port on which the video source is added. If the process encounters a channel that
does not have “Port Free” status then the video source will be added to the un-allocated list; consecutive
cameras will only be applied to channels that are Port Free.
For example the Layer 3 Enhanced CCTV Switch has channel ports 1,3,4 listed as Port Free, 2 is an
Analogue camera. If one 4 channel ICR encoder is added to camera 1. The result is;
► ICR Encoder - Camera 1 -> Camera 1 NVR
◄ ICR Encoder - Camera 2 -> Unallocated, Cameras
► ICR Encoder - Camera 3 -> Camera 3 NVR
► ICR Encoder - Camera 4 -> Camera 4 NVR.
KBD
USB
NET
AUDIO
IN
VID 1
MON
B
VID 2 VID 3
SATA1
OUT
A
VID 13VID 8VID 6VID 4 VID 5 VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15 VID 16
ALARMS
RELAYS
SERIAL 1
SERIAL 2
SERIAL 3 PTZ
SERIAL 4 PTZ
AUDIO
IN
OUT
EXP
O
I
IR
MON A
HDMI 1
VID 17 VID 18 VID 19 VID 29VID 24VID 22VID 20 VID 21 VID 23 VID 25 VID 26 VID 28 VID 27 VID 30 VID 31 VID 32
NET
Layer3 Enhanced
CCTV Switch
Port reserved for
analogue
connections on NVR
Video source
added to
un-allocated list
NET 1
NET 0
POE IN
POWER
VID IN
SERIAL 1
SERIAL 2
1
3
4
Key
Port Free
Analogue Connection
Single IP connected
Single IP assigned
Multiple IP connection
Unknown
IP detected
2
When a multichannel encoder is connected to the Layer 3 Enhanced CCTV Switch, the NVR will receive
information from the encoder about how many cameras are connected. Channels set as Not Connected
on the encoder, when presented to the Enhanced Layer 3 switch will not be eligible for Auto IP.
Intelligent Security & Fire Ltd
Page 20
20
NV4
In the scenario shown below, the NVR is set at defaults and the Layer 3 Enhanced CCTV Switch has an
ICR encoder with three analogue camera inputs connected at positions 1, 3 and 4. Position 2 is not used.
The Closed IPTV NVR would be auto congured on consecutive ports, camera 2 would not be allocated
to port 2 which would be registered as assigned to a failed camera.
KBD
USB
NET
AUDIO
IN
VID 1
MON
B
VID 2 VID 3
SATA1
OUT
A
VID 13VID 8VID 6VID 4 VID 5 VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15 VID 16
ALARMS
RELAYS
SERIAL 1
SERIAL 2
SERIAL 3 PTZ
SERIAL 4 PTZ
AUDIO
IN
OUT
EXP
O
I
IR
MON A
HDMI 1
VID 17 VID 18 VID 19 VID 29VID 24VID 22VID 20 VID 21 VID 23 VID 25 VID 26 VID 28 VID 27 VID 30 VID 31 VID 32
NET
Layer3 Enhanced
CCTV Switch
Shows as
Camfail
Shows as
Camfail
NET 1
NET 0
POE IN
POWER
VID IN
SERIAL 1
SERIAL 2
1
3
4
2
Key
Port Free
Analogue Connection
Single IP connected
Single IP assigned
Multiple IP connection
Unknown
IP detected
Analogue channels take precedence. If an analogue camera is present and connected then it will only
become Port Free if the channel is set to Not Connected on the Closed IP NVR conguration pages.
The de-allocated cameras are added to the Camera->Unallocated Cameras page on the NVR, which
shows a tabulated list of all unallocated cameras connected to the switch, showing all the camera details
(DNS, Auto IP Address, MAC, Classication, Channel number and Native resolution). Each camera has a
drop down list showing all ‘Port Free’ channels available for allocation to the video source.
Any errors in setting up the cameras can be rectied by simply disconnecting and reconnecting the
camera to the switch in whilst conguration mode, which will allow the camera to reallocate. If multiple
changes are made, it is recommended that the NVR is reset after correcting the conguration to ensure
perfect allocation.
IMPORTANT: For further information refer to the Layer 3 Enhanced CCTV Switch manual
Intelligent Security & Fire Ltd
Page 21
21
Installation Guide
Conguring the Unit
The unit can be congured either on the local monitor or over the network using a PC with Internet
Explorer or similar browser. Both have near identical menu interfaces.
Accessing the menus on a local monitor
The Conguration pages can be displayed on a local monitor.
When connected, press the MENU button on the IR Remote Control.
Note: If the IR Remote Control does not open the conguration menus, press the DVR button to make
sure it is in DVR mode, then press the MENU button again.
Accessing the menus on a PC web browser
Locating the Unit IP address
The IP address of the unit is required to access the webpages. It can be identied from the conguration
menu pages using the local monitor, press the MENU button on the IR Remote Control and navigate to
the System Settings->System menu to nd the DHCP assigned IP address.
Note: The unit can be installed in a DHCP network environment where an IP address, subnet mask and
default gateway will automatically be allocated from the network DHCP Server (DHCP is enabled
by default).
Note: If a DNS (Domain Name Server) address is not to be used, it is strongly advised that a xed IP
address be assigned (a DHCP assigned address can change without notication i.e. following
power failure).
A xed IP address can be assigned via the Network Settings->Network menu.
For information on locating the unit’s IP address via a PC and serial port connection, refer to Appendix D.
Default DNS Address
It is recommended that a DNS (Domain Name Server) address be congured. Assigning a recognisable
name can help a remote user to locate the unit.
If no System name is allocated to the unit, the default DNS address will be:
machine serial number.yourdomain.com
• <machine serial number> is displayed in the System menu
page and also on the underside of
the unit.
• <yourdomain> is the name assigned to your
DNS network.
The default DNS address can be renamed via the System->Attributes menu. Following renaming, the
DNS address will be::
yourname.yourdomain.com
• ’ yourname‘ is the name assigned via the Network menu.
Note: To activate an assigned DNS address, it will be necessary to reboot the unit. The unit can be
rebooted via System -> Maintain-> Reset.
IMPORTANT: To set the time and date on the unit, navigate to System Settings->Time and Date.
6.11
Intelligent Security & Fire Ltd
Page 22
22
NV4
Accessing the Conguration Webpages
The unit can be congured using the webpages. To access these:
1. Launch Internet Explorer (or similar web browser package).
2. Type the URL for the unit (IP or DNS address).
3. The Opening menu page will be displayed.
Conguring Closed IPTV
It is only possible to change Closed IPTV settings when the system is in Conguration mode (Closed
IPTV->Settings). The Closed IPTV logo in the top corner of the conguration pages gives a quick
indication of whether the system is in Secure or Conguration mode. Dedicated Micros recommend the
system is always left in Secure Mode unless Closed IPTV settings are actually being edited.
Secure Mode
Conguration Mode
6.13
Intelligent Security & Fire Ltd
Page 23
23
Installation Guide
Remote Control
The IR Remote Control offers all the control functionality required to navigate the menus.
Note: Not all buttons on the IR Remote Control are relevant for the Unit.
Key Button
Switches the Remote Control to ‘TV’
mode and sends codes understood by
common TV sets.
Switches the Remote Control to ‘DVR’
mode. Note the DVR mode is the
default mode of operation.
Toggle the speed of PTZ camera
movement (two speeds available).
Use the Zoom button to zoom in/out
with a selected camera. Also used to
zoom (x2) into Live or Playback images.
This button will change the Zoom Keys
operation to focus or iris functions
(when available).
Use this button to cycle through
available cameras.
This button should be pressed (followed
by a numeric entry) to carry out auxiliary
actions on a PTZ camera.
Press the Menu button to enter the
Conguration menus.
Press the Exit button to exit the
Conguration menus.
Intelligent Security & Fire Ltd
Page 24
24
NV4
Use the Directional and OK buttons to navigate through
the menu screens and accept changes. Also use for PTZ
telemetry control of cameras.
Use the Softkeys (Red, Green, Yellow, Purple) to directly
access the corresponding function displayed on the menu
screen.
The Number pad should be used to select specic
cameras and preset positions when available.
Use the Playback buttons to interrogate recorded images.
Use the LIVE button to switch from Playback or menus to
a LIVE display.
Intelligent Security & Fire Ltd
Page 25
25
Installation Guide
Main Menu
When rst accessing the unit, the main menu will be displayed. This menu allows access to the
Conguration menus, the Viewer menus and also several Download options.
Note: The Download options will only be available if viewing remotely via an IP connection.
Select the Conguration menu tab to access the unit’s Conguration menus, refer to ‘Navigating the
Conguration Menus’ for further guidance.
Select the Event Search tab to access the unit’s Event Search function, refer to ‘Event Search’ for further
guidance.
Note: The ‘Event Search’ option will only be displayed if ‘Enable Event Search’ is selected in the
‘Features’ menu: System Settings->Features.
Select the Viewer menu tab to access the unit’s Viewer function, refer to ‘Unit Operation’ for information
on the numerous Viewer features.
Select the Download menu tab to access the various Download sub-options. Select from:
• Product Manual Select to open an electronic version of the Installation &
Operation Guide.
• ObserVer Manual Select to open an electronic version of the NetVu ObserVer
User Guide. NetVu ObserVer is a free video management
software package from Dedicated Micros that allows users to
seamlessly view distributed images from any ‘NetVu Connected’
product.
• NetVu ObserVer Select to download the NetVu ObserVer video management
software.
Intelligent Security & Fire Ltd
Page 26
26
NV4
• Java (JRE) Select to download the Java (JRE) software (from the unit).
This software is required to successfully view Conguration
and Viewer menus remotely.
IMPORTANT: By default, no Usernames and Passwords are required to access any of the various
menus. Usernames and Passwords can however be added to regulate access to the
Conguration and Viewer menus. Refer to the ‘Console Settings-> User Accounts’ menu
for information on establishing Usernames and Passwords.
Intelligent Security & Fire Ltd
Page 27
27
Installation Guide
Navigating The Conguration Menus
The menu tree provides access to the conguration menus.
The conguration pages are navigated using the menu tree (displayed on the left of each page). Selecting
one of the menu options will display the relevant page. Associated sub-menus will then be available.
Relevant menus can also be accessed directly from other menu screens via the coloured softkey options
shown at the base of each menu. The options available will depend on the menu being viewed. Select
a softkey option by pressing either the corresponding button on the IR Remote Control (if viewing the
menus locally), or by selecting the relevant option via the PC mouse (if viewing the webpages).
Note: Any changes made via the webpages are automatically saved when the page is closed. To
‘manually’ save changes, select the Save option.
IMPORTANT: The Closed IPTV logo gives a clear indication of when security is enabled.
Secure Mode Conguration Mode
Intelligent Security & Fire Ltd
Page 28
28
NV4
Using the IR Remote Control
Press the MENU button to access conguration menus via a connected local monitor. The menu will
have a red indicator highlighting the rst option. Select a main menu heading to open a drop down list of
further sub-options. Press the Down Directional button to highlight the next menu option, press OK on the
highlighted menu.
Press the Right Directional button to highlight the rst editable parameter on the screen.
Use the Left/Right/Up/Down Directional buttons to move between elds.
Select OK to start editing a eld (the option will be outlined in green).
Use the Up/Down Directional buttons to change the settings within an editable eld.
Use the OK button to accept a new setting. Use the coloured softkeys to select the accompanying colour
option on screen i.e. red button to select the red option. To undo changes made to any menu, select the
Refresh (Purple) option.
Note: See below for information on entering alpha-numeric data.
Entering Alpha-Numeric Data via a Local Monitor
Numeric or text data is entered using the on-screen Virtual Keyboard (Arrow Key Editor).
To display the Virtual Keyboard, navigate to the relevant text input box using the Directional buttons
and double press the OK button twice on the IR Remote Control or Front Panel Interface. The Virtual
Keyboard is displayed.
Use the Directional buttons to move between characters, use the OK button to select a character. Select
‘Submit’ to enter details, press ‘Cancel’ to exit without entering any text.
Alpha-numeric data can also be entered in either upper or lower case format by ‘multi-tapping’ a relevant
button. For example, with the cursor located in the text entry window of the Virtual Keyboard, repeatedly
tap button ‘2’ to cycle through the following characters: 2,A,a,B,b,C,c,2 etc.
To select one of these characters, simply stop tapping the button when the chosen character is displayed.
The cursor will then progress, ready for the next character entry.
Note: A USB Keyboard (not supplied) can be connected via one of the USB ports on the unit. The USB
Keyboard can then be used to enter alpha-numeric data via the local menus.
Using a USB Mouse or the Webpages
Navigate the menus by clicking the tabs displayed on the left of the menu headings (on the menu tree).
The rst option is highlighted with a red tab. Select a main menu heading to open a drop down list of
further sub-options.
Highlight an editable eld by clicking on it directly.
If viewing pages locally, enter alpha numeric data via the Arrow Key Editor (see above). If viewing
remotely, enter via the PC keyboard. If available, click on the drop down menus to select settings.
Note: A selected item in the drop down list will appear highlighted.
Navigating away from a page (clicking on a different option on the menu tree) will automatically save any
changed settings. To undo changes made to any menu, select the Refresh (Purple) option.
Using a Supported Dedicated Micros Keyboard (DM/KBC1 & DM/KBC2)
The unit can also be controlled using an optional Dedicated Micros keyboard. This is connected via the
KBD connector on the rear of the unit and provides the same control functions as the I.R Remote Control.
Note: Refer to ‘Using the optional Keyboards (DM/KBC1 & DM/KBC2)’ for further guidance.
Intelligent Security & Fire Ltd
Page 29
29
Installation Guide
System Settings
The menus under the System Settings heading allow the unit’s core settings to be viewed, changed and
the system software upgraded.
The Attributes option displays details about the unit including the IP address, unit serial number, MAC
address and software version.
The Status page displays information about the unit’s operating condition, shows how long the unit has
been operating and the reason for the last reset. It also shows camera status and displays any failed
cameras.
The Language page allows the system language to be set. The language can also be changed for the
current session only.
The Time and Date page allows the unit time and date settings to be adjusted, including setting
the timezone.
The Serial Ports page allows each of the four serial ports to be individually congured for one of a range
of operations, including EPOS, debug, PPP and telemetry.
The Audio page shows the settings available for each of the audio channels and allows conguration of
audio quality.
The Features page allows control of the different features that are available within the software including
Email reporting, webcam support and control of the display resolution.
The Maintain page allows the current conguration to be saved, and for previously saved settings to be
loaded. It also enables easy upgrade of the system software.
The PowerScript Mgmt page allows installed PowerScripts to be activated/deactivated on start-up.
Intelligent Security & Fire Ltd
Page 30
30
NV4
Attributes
6.13
This menu shows the general information about the unit including the version of software installed, the
unit’s serial number and the allocated DHCP IP address.
Product Descriptor Details the product model.
Serial Number Identies the serial number of the specic unit.
PCB Serial Number Displays the PCB (Printed Circuit Board) serial number of the unit.
Product Code Displays a code identifying the unit’s specication.
Earliest Recording Displays the date/time of the earliest recording held on the unit.
System Name This eld can be edited to allocate a name to the unit. This is displayed
when the unit is accessed via NetVu ObserVer and is sent when
transmitting information to a Remote Video Response Centres (RVRC).
Video Standard Displays the video standard adopted by the unit i.e. PAL, NTSC.
Number of Cameras Shows the number of camera channels on the unit.
Global PPS Details the Global PPS (Pictures Per Second) recording rate for all
cameras at 4CIF, 2CIF and CIF.
Video Storage Gbytes Highlights the available video storage capacity in Gigabytes.
MAC Address This is the MAC address assigned to the unit.
IP Address This is the IP address allocated to the unit.
Sub Net This is the subnet of the network where the unit is located.
Gateway This is the IP address of the default gateway (router) assigned by the
DHCP server.
Intelligent Security & Fire Ltd
Page 31
31
Installation Guide
Software (Red) Select this option to display installed software information
(see below).
Time/Date (Green) Select to open the System->Time and Date page.
Accounts (Yellow) Select to open the Display->User Accounts page.
Network (Blue) Select to open the Network->Network page.
Refresh (Purple) Refreshes the information on the current page.
Software Menu
Software Revision This identies the version of software the unit is running.
Codec Revision This identies the codec version the unit is running.
Webpage Revision This identies the webpage version the unit is running.
Framestore Revision This identies the Framestore Revision the unit is running.
PC Apps Revision This identies the revision archive of the Viewer and associated PC
Apps software.
Boot Software Rev. Displays the infrastructure componentry software revision.
Help Videos Rev. This identies the version of Help Videos installed on the unit.
Note: Refer to ‘Go To Viewer->Help Videos’ for guidance on viewing the embedded Help Videos.
Telem PIC Rev. This identies the version of the Telemetry control device installed on
the unit.
Applet Version This identies the applet version installed on the unit
Note: Refer to ‘Display Settings->Viewer Defaults’ for guidance on using a remote applet (this can
lessen load times when accessing multiple DVRs/Servers).
Intelligent Security & Fire Ltd
Page 32
32
NV4
System (Red) Select this option to return to the System menu.
About (Blue) Select to open the Status->About page.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 33
33
Installation Guide
Status
This menu details information regarding the status of the unit, notably the total time the unit has been
operating and the time since its last reset. Status log information can also be exported via the ‘Export
Logs’ option to either a CD-R/DVD-R or a USB device.
Time since last reset Details the time since the unit was last reset.
Total running time Details the total time the unit has been operational.
Reset code The last reset code used is displayed.
Restart reason The reason for the last restart is displayed.
Codec Up to four codecs are installed within the unit (dependent on model).
Cameras are assigned to the codec in the following sequence: Camera
1 is assigned to Codec 1, Camera 2 to Codec 2, Camera 3 to Codec
3, Camera 4 to Codec 4, Camera 5 to Codec 1, Camera 6 to Codec 2,
etc.
Within each Codec window, each camera channel is listed, along with
connection, recording and camera status information.
Cameras Cameras assigned to each codec are displayed..
Connected Those camera channels with cameras connected will be highlighted
light green. Those not in use will appear dark green.
Intelligent Security & Fire Ltd
Page 34
34
NV4
Recording Those camera channels that are currently recording are highlighted
light green. Those not recording will appear
dark green.
Cam Status Those camera channels where the connection is deemed to be
functioning correctly will be highlighted light green. Those deemed
to have failed will appear red. Camera channels with no connected
camera will appear dark green.
Alarm Status (Yellow) Select to open to the Status->Alarm page.
Rem Codec (Blue) Select to open to the Remote Codec Status page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 35
35
Installation Guide
Alarm Status
This menu details information regarding the status of the unit’s alarm contacts, alarm zones and relay
outputs.
Alarm Contacts/Zones/Relay Outputs Alarm Contacts, Alarm Zones and Relay Outputs that are in an
‘active’ state are shown light green. ‘In-active’ ones appear dark
green (not illuminated).
Alarms (Blue) Select to open to the Alarm->Inputs page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 36
36
NV4
About
This menu allows access to numerous system information pages. Select the an icon to view the relevant
pages, refer to ‘Appendix J - Status Pages’ for a description of each page.
System Information Select to open to the System->Attributes page.
Software Revisions Select to open to the System Settings->System->Software page.
Intelligent Security & Fire Ltd
Page 37
37
Installation Guide
Logs
The log les stored in the unit can be accessed from this page. Selected logs are displayed on the page
below.
About (Blue) Select to open the System->Status->About page.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 38
38
NV4
Language
This menu allows the system language to be set. Changing the System Language will effect all menu
pages. If required, the language can also be changed for the current session only.
System Language Select to change the system language setting.
Reset (Red) Select to reset the unit.
Note: The unit MUST be reset to implement system language changes, refer to
System Settings->Maintain for guidance on resetting the unit.
Session Language Select to change the language settings for the current
session only.
Choose Select to immediately activate session language changes.
Reset (Red) Select to reset the unit.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 39
39
Installation Guide
Time and Date
This menu allows the time and date to be set on the unit. Required timezone information can also be
established and the unit time synchronised to that of the PC being used to view the webpages.
System Time The current system time and date is displayed.
Current Time Zone Displays the currently selected time zone settings.
Time Format As default, the time displayed is in 12 hour format. This can be changed
to 24 hour if required.
Date Format As default, the date is entered dd/mm/yy. It can also be displayed as
mm/dd/yy or yy/mm/dd.
Set Time Enter a current time for the unit.
Set Date Enter a current date for the unit.
Set Time (Green) When current time/date as been entered, select this button to
implement changes.
Time Zone Select the relevant timezone offset from the accompanying drop down
menu.
SNTP Server A Simple Network Time Protocol (SNTP) server allows external devices
to connect and set their current date and time settings to that of the
SNTP. If required, enter the SNTP server IP address here.
Note: It is recommended that an SNTP server is congured. Suitable networked SNTP servers can be
found here: http://support.ntp.org/bin/view/Servers/NTPPoolServers
Intelligent Security & Fire Ltd
Page 40
40
NV4
Alternatively most DHCP and DNS servers also run SNTP services. Contact your system
administrator for further assistance.
PC Time Displays the system time of the PC currently being used to view the
webpages.
Sync Time (Blue) Use this button to synchronise the time of the unit to that of the PC
being used to view the webpages.
Note: The PC Time and Sync Time options will only be available if viewing the menu via
the webpages.
Reset (Red) Select to reset the unit.
Set Time (Green) When current time/date as been entered, select this button to
implement changes.
System (Yellow) Select to open the System->Attributes page.
Sync Time (Blue) Use this button to synchronise the time of the unit to that of the PC
being used to view the webpages.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 41
41
Installation Guide
Serial Ports
This menu allows conguration of the unit’s Serial ports, refer to ‘Installing the Unit’ for
installation information.
Serial Port These are the four serial ports available.
Port Cong The serial ports can be congured to specic uses.
Select from:
None Switches port off
Debug Sets port for serial communications
PPP Sets port for Point to Point Protocol
Telem Sets port for Telemetry purposes
Comm Sets port for Comms purposes
EPOS Sets the serial port for connection to an
EPOS (Electronic Point Of Sale) device
Note: It is recommended that Serial port 1 be set for ‘Debug’ operations.
Interface Type Choose the type of serial interface being used. Select from RS232,
RS485 or RS422.
Baud/Parity/Data/Stop/Flow Control
These options allow the Serial port communication settings to
be congured.
Note: These settings will default to pre-determined values that match the selected protocol and should
not normally be altered.
Intelligent Security & Fire Ltd
Page 42
42
NV4
Protocol This is a drop down list of serial telemetry protocols supported by the
unit.
Note: Refer to ‘Appendix G’ for a full list of supported telemetry protocols.
Reset (Red) Select to reset the unit.
Maintain (Green) Select to open the System->Maintain page
Text In Img (Yellow) Select to open the Features & Text->Text->Text In Image page
Camera (Blue) Select to open the Camera Conguration page (below).
Refresh (Purple) Refreshes the information on the current page.
Camera Conguration
This page allows conguration of some features on cameras connected to the unit.
Update local sys cong on save Select to update and enforce any changes made here in the local
system display.
Camera Nuisance Count This is a repetitive detector value. When a camera failure alarm is
received on the unit, it will store the alarm time and monitor the number
of times the same alarm is triggered within an hour period. If the
detector is triggered the number of times entered here, the unit will set
the camera to ‘No Connection’. To disable this feature, leave the setting
as ‘0’.
Title Titles assigned to each camera are displayed.
Intelligent Security & Fire Ltd
Page 43
43
Installation Guide
Mode The settings will default to ‘Colour’. If Monochrome cameras are used,
select ‘Mono’. Selecting ‘Mono’ will remove colour patterning. If
a particular channel is not in use or the camera has failed, select ‘Not
Connected’.
‘Rem Codec’ is used for NetVu Connected video sources. ‘IP
Camera’ is used for all NetVu Connected cameras and 3rd party units.
Fail Rep Select this option to activate a Failure report in the event of
camera connection failure (video loss).
Cam Setup (Red) Select to open the Camera->Setup page
Serial (Blue) Select to open the System->Serial page
Refresh (Purple) Refreshes the information on the current page
Intelligent Security & Fire Ltd
Page 44
44
NV4
Audio
The Audio menu allows settings for the bi-directional audio channels to be edited. Two audio can be
recorded via the inputs, or Challenge audio i.e. originating from an Operator using NetVu ObserVer at a
Remote Video Receiving Centre (RVRC) can be recorded with one external input. Challenge audio is
then available on Audio Output 1.
Audio 1/2 Use the drop down box to assign an audio function to each input,
‘Local’ is Audio recorded from local inputs, ‘Challenge’ audio originates
from an Operator using NetVu ObserVer at a Remote Video Receiving
Centre (RVRC).
Audio Recording Select ‘Enable’ to activate Audio recording. Note that this is a global
action which when Enabled, will result in all audio received by the unit
being recorded to the HDD.
Record Audio Challenge Select this option to record an audio challenge received via an IP
connection i.e. originating from a remote client.
Record Gain This option allows the Record Gain level to be set. This is the base
setting from which the AGC (Automatic Gain Control) will operate.
Select from 1 to 15. The default and recommended setting is 15.
Playback Volume Select a volume setting between 1 to 64 for audio playback.
Record AGC Select this option to activate the AGC function. AGC helps produce a
better quality recording by removing background noise/distortion.
Record uncompressed Select this option to record audio in an uncompressed format.
Note: Recording in uncompressed format will signicantly increase the disk space used.
Intelligent Security & Fire Ltd
Page 45
45
Installation Guide
Reset (Red) Select to reset the unit.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 46
46
NV4
Features
These menus enables the activation of numerous system features. Features are grouped within four submenus: System, Network, Video and Other.
System
User Logging Enable this option to activate User Logging, refer to ‘Appendix B’ for
further information regarding the User Logging function.
Enable External Modules Select to enable any connected RS485 alarm modules.
Text in Images Select this option to activate the Text in Images function, refer to ‘Text-
Text In Image’ for more information.
Note: When de-selected here, the ‘Text in Image’ menu will no longer be displayed in
the menu tree.
Email Reporting Select this option to activate the Email Reporting function, refer to
‘Network->Email’ for more information.
Note: When de-selected here, the ‘Email Reporting’ menu will no longer be displayed in
the menu tree.
Keyboard Enable (485 bus) Select this option to enable the Keyboard 485 Bus.
Remote Reporting Select this option to activate the Remote Reporting function, refer to
‘Network->Remote Reporting’ for more information.
Note: When de-selected here, the ‘Remote Reporting’ menu will no longer be displayed in
the menu tree.
Intelligent Security & Fire Ltd
Page 47
47
Installation Guide
Automatic FTP Download Select this option to enable automatic FTP downloads to upgrade the
unit and/or the webpages, refer to ‘Network->FTP Download’ for more
information.
Note: When de-selected here, the ‘Automatic FTP Download’ menu will no longer be displayed in
the menu tree.
SMB Server Support Select this option to activate the SMB (Server Message Block) le
sharing function. When activated, the SMB protocol allows the unit
to access PCs operating the Windows operating system (and Linux
machines running Samba). This enables sharing of les and directories
to/from the unit. The name of the SMB Workgroup on the network
must be correctly entered in the SMB Workgroup option (see below).
It is important that the Server Name assigned to the unit via ‘Network
Settings->Server Name’ is unique within the workgroup being used.
To access the unit via a PC running SMB (and having access to the
same Workgroup); open My Network Places-Entire Network- Microsoft
Windows Network. The Workgroup containing the unit and PC(s)
should then be available. Files and folders can then be copied/added
as required.
Note: Use the 10/100Mbps network option ‘Net 2’ for SMB purposes (the unique Server Name must be
assigned via ‘Network->Server Name’).
Camera Masking Select this option to activate the Camera Masking function. When
activated, any attempt to obscure a connected cameras lens will be
noted and an alarm event will be logged.
System (Red) Select to open the System->Features->System page
Network (Green) Select to open the System->Features->Network page
Video (Yellow) Select to open the System->Features->Video page
Other (Blue) Select to open the System->Features->Other page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 48
48
NV4
Network
Note: For normal operation it is recommended that Network menu options be left at their
default settings.
Secondary Web Port If the default port setting for web serving has already been allocated, it
is possible to congure a second port number
i.e. the secondary web port can be set to 8000 if the default web port
(80) is blocked by the network or rewall.
Use Record Proles for Tx High Select this option when units required Video Transmission prole (rate/
quality/resolution) is identical to that being recorded.
Telem UDP Port Selection Select ‘Automatic’ to enable the unit to select a suitable port for
telemetry purposes.
Select ‘Default’ to use the default port settings (1025).
Select ‘User Dened’ to use settings entered in the ‘Telemetry Port’
option.
Samba Workgroup Enter the name of the Samba workgroup to enable sharing of les and
directories to/from the unit. To access the unit via a PC running SMB
(and has access to the same Workgroup); open My Network PlacesEntire Network- Microsoft Windows Network. The Workgroup containing
the unit and PC(s) should then be available. Files and folders can then
be copied/added as required.
Auto IP Override Enables/disables Auto IP Address allocation by the Zeroconf protocol.
Intelligent Security & Fire Ltd
Page 49
49
Installation Guide
Max Client Connections This setting limits the number of client connections to the server.
The default value is 256 but could be increased if there is heavy
network trafc.
ARP Cache Size This setting limits the number of cache entries available in the ARP
table. The default setting of 256 is adequate for
most instances.
Note: The Address Resolution Protocol (or ARP) is used to link the IP address to the Ethernet address
(MAC Addres). In a Closed IP network such as this, once in secure mode the IP address is
unlikely to change. The default entry of 256 should only be changed under
expert advise.
TCP Reassembly Queue Limit This setting limits the maximum number of TCP segments allowed in
t
he reassembly queue. Preventing the construction of highly segmented
data helps protect against a common DoS
(Denial of Service) attack.
Remote Codec Default Connection
This selects the initial connection type to use for an auto congured
remote codec camera, select from TCP or UDP
System (Red) Select to open the System->Features->System page
Network (Green) Select to open the System->Features->Network page
Video (Yellow) Select to open the System->Features->Video page
Other (Blue) Select to open the System->Features->Other page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 50
50
NV4
Video
Detected Video Standard
The unit automatically detects the video standard being used i.e.
PAL/NTSC.
Video Resolution (h x v) Allows selection of the resolution, options are 704 x 576, 704 x 512 and
640 x 512
Deinterlace Filter When Enabled, this option will improve the appearance of moving
objects by applying a deinterlace lter that minimises the comb effect
that can be visible when recording high motion scenes in 4CIF mode.
It
is recommended that this option be enabled when recording in 4CIF mode.
Comb Filter Enable this option to activate the Comb Filter function. Comb Filter can
help improve the ne details of a video signal image by ltering the
luminance and chrominance separation process.
Disable Transcoding Select to disable the unit’s transcoding capabilities. In normal
circumstances this should always remain enabled,
3D Input Filter Advanced input ltering to the video codec, providing input signal
noise reduction. It’s primary purpose is to reduce noise observed when
viewing standard denition cameras or HD monitors. Options are Off,
Time Domain Filter, Spatial Filter, or Both.
Enable Privacy Zones Privacy zones can be used to electronically mask sensitive areas that
should not be available for viewing, refer to Camera->Privacy Zones for
more information.
Intelligent Security & Fire Ltd
Page 51
51
Installation Guide
Segment Aspect Ratio This setting controls how a 4:3 image is displayed in a multi-screen or
wide screen format on the local viewer. The available display segment
changes depending on the number of multi screen images selected for
display.
Stretch forces the image to ll the available display segment. This may
result in some distortion of the display image.
Zoom Fit forces the frame to ll the available segment completely and
proportionally. Consequently some of the image at the top and bottom
of the frame may be cropped.
Frame Fit forces the frame to ll the available segment proportionally,
resulting in black bars left and right on some multi display choices.
Note: There is no cropping or distortion on the recorded image, these settings are for display only.
System (Red) Select to open the System->Features->System page
Network (Green) Select to open the System->Features->Network page
Video (Yellow) Select to open the System->Features->Video page
Other (Blue) Select to open the System->Features->Other page
Refresh (Purple) Refreshes the information on the current page
Intelligent Security & Fire Ltd
Page 52
52
NV4
Other
Auto Update Web Variables Congures the unit to update all system variables required for an
automatic upgrade without requiring conrmation. Do not check this box
if you run a customised applet.
Enable event search page Select to enable the Event Search option. When enabled, the option
will appear within the Conguration Menu tree, refer to ‘Navigating the
Conguration Menus->Event Search’ for further details.
Enable RVRC page Select this option to activate the RVRC Remote Set/Unset/Override
function, refer to ‘Record Settings->RVRC’ for more information.
Note: When de-selected here, the ‘RVRC’ menu will no longer be displayed in the menu tree.
System (Red) Select to open the System->Features->System page
Network (Green) Select to open the System->Features->Network page
Video (Yellow) Select to open the System->Features->Video page
Other (Blue) Select to open the System->Features->Other page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 53
53
Installation Guide
Maintain
This menu allows the unit to be reset and a software upgrade to be performed via an inserted CD-R/
DVD-R or a connected USB device. Current unit settings can also be saved for future use and previously
saved settings restored.
Conguration
Default (Green) Select to return the unit to its factory default settings.
Note: Selecting the Default button will cause the system to reboot.
Save (Purple) This button uses the select box and the to/from box. Select to save the
selected settings to the selected media.
Restore (Blue) This button uses the select box and the to/from box. Select to save the
selected settings to the selected media.
Note: Selecting the Restore button will cause the system to reboot.
select Select which les will be saved or restored.
To/From Select the relevant media device to save to or restore from i.e. USB or
CD-R/DVD-R.
Export Logs
Export Logs (Yellow) Select to export all Logged data to a connected external device.
To Select the relevant media device to save to export to.
Server
Reset (Red) Select to reset the unit.
Intelligent Security & Fire Ltd
Page 54
54
NV4
IMPORTANT: To upgrade the unit, insert a media device containing relevant software upgrades
and select ‘Reset‘.
Note: For the latest software upgrades, please refer to the Dedicated Micros website:
www.dedicatedmicros.com
Note: Selecting the Default button will cause the system to reboot.
Reset (Red) Select to reset the unit.
Default (Green) Select to return the unit to its factory default settings.
Export Logs (Yellow) Select to export all Logged data to a connected external device.
Restore (Blue) Select to restore previously saved settings from the selected media.
Save (Purple) Select to save current unit settings to the selected media.
Intelligent Security & Fire Ltd
Page 55
55
Installation Guide
PowerScript Mgmt
This menu enables installed PowerScripts to be activated/deactivated on start-up. Use the tickbox(es) to
select/deselect installed PowerScripts, then select Save (Green). A system reset will be required for the
changes to take affect.
Note: Changes this page will alter the ‘Default.C’ le. If you already have a custom PowerScript on your
unit which uses Default.C, please contact Dedicated Micros Technical Support for guidance Tel:
+44 (0) 845 600 9502 for further guidance.
Reset (Red) Select to cycle the power to the unit.
Save (Green) Updates the DEFAULT.C le on the NVR to enable selected scripts on
reboot.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 56
56
NV4
Closed IPTV
Dedicated Micros’ ground breaking Closed IPTV solution makes deploying an IP Video, CCTV system
safe, secure and simple. Combining patent-pending innovation with zeroconf networking technology,
Closed IPTV automatically allocates IP addresses to IP cameras by physical port. This ground breaking
solution provides a very simple and secure answer to IP Video, meaning that no prior knowledge of IP
networking is required.
The menus under the Closed IPTV heading become active when the Closed IPTV feature has been
enabled and there is at least one Layer 3 Enhanced CCTV Switch connected.
The Settings page provides access to the majority of conguration options for the feature, and is used
to enable conguration of the switches, setting the security and access features whilst also giving an
overview of the port status of each connected switch..
The Discover page allows automatic discovery of Layer 3 Enhanced CCTV Switches connected to the
Closed IPTV NVR.
The Upgrade Switch page allows connected Layer 3 Enhanced CCTV Switches to be quickly, easily and
securely upgraded.
The Advanced page allows switch base camera numbers to be set, and camera details to be
synchronised automatically.
Conguring Closed IPTV
It is only possible to change Closed IPTV settings when the system is in Conguration mode (Closed
IPTV->Settings). The Closed IPTV logo in the top corner of the conguration pages gives a quick
indication of whether the system is in Secure or Conguration mode. The main display will also say if the
unit is in Conguration mode. Dedicated Micros strongly recommend the system is always left in Secure
Mode unless Closed IPTV settings are actually being edited.
Secure Mode Conguration Mode
Intelligent Security & Fire Ltd
Page 57
57
Installation Guide
Settings
Note: The blue ‘i’ in a circle is a link to in-page help. Click on a symbol to get help about the adjacent
menu item.
The on-screen image of the Layer 3 Enhanced CCTV Switch provides instant information regarding
camera connection ports.
It is advisable to only allocate ONE camera (analogue or IP) to each available port.
Each Layer 3 Enhanced CCTV Switch has a rotary dial on the base to allow a unique (in the cascade)
identier to be set. Port to Channel mappings are allocated using a combination of this rotary dial and the
‘Base Camera’ setting on the Closed IPTV settings menu.
Layer3 Enhanced
CCTV Switch
Layer3 Enhanced
CCTV Switch
Layer3 Enhanced
CCTV Switch
Layer3 Enhanced
CCTV Switch
KBD
USB
ETH-0
AUX AUD1
IN
VID 1
MON
B
VID 2 VID 3
SATA1
OUT
A
VID 8VID 6VID 4 VID 5 VID 7
ALARMS
RELAYS
SERIAL 1
SERIAL 2
SERIAL 3 PTZ
SERIAL 4 PTZ
AUX AUD2
IN
OUT
EXP
O
I
IR
SATA2
ETH-1
HDMI 1
AUD 1
AUD 2 AUD 3 AUD 4 AUD 5 AUD 6 AUD 7 AUD 8
HDMI 2
ETH-D
ETH-C
ETH-B
ETH-A
VID 9 VID 10 VID 11 VID 16VID 14VID 12 VID 13 VID 15
AUD 9
AUD 10 AUD 11 AUD 12 AUD 13 AUD 14 AUD 15 AUD 16
et V Serer
Default Settings
Switch No Camera Nos
0 1-16
1 17-32
Intelligent Security & Fire Ltd
Page 58
58
NV4
Port Illustration Colour Key
Port Free (Black) █ No video source currently connected to the port and nothing
assigned to that channel.
Analog Connection (Blue) █ Analogue camera input using the BNC connection for this
channel on the back of the NVR. Analogue cameras take
priority over IP cameras when channels are being assigned; if
an IP camera is put into the port on the switch associated with
an a channel allocated to an analogue input, the IP camera will
go into the un-allocated camera list and the port icon will turn
orange to signify Duplicate Port Allocation (see below).
Single IP Connected (Green) █ A single IP camera is connected directly to the port and will be
auto assigned to the channel.
Single IP Assigned (Turquoise) █ A camera that has either ;
been congured manually independently outside Closed IPTV
or
is one of the cameras (above camera 1 of the encoder)
assigned by Closed IPTV by connecting a multi channel
encoder.
Multiple IP Connections (Yellow)
█ A port that is hosting a multiple channel input eg a connection to
a multi channel encoder. The cameras after this are treated by
the NVR as Single IP Assigned.
Duplicate Channel Allocation (Orange)
█ A port that has analogue and IP connection applied to it. The IP
source will be un-allocated.
Unknown (White) A port which has detected a network connection but the type of
connected device is not recognised.
IP Detected (Magenta) █ A port which has detected a network connection but the
device is either not assigned to current channel or is assigned
elsewhere.
Security Level Select from Conguration Mode’ or ‘Secure Mode’.
In Conguration mode;
● The security settings of all cascaded Layer 3 Enhanced CCTV
Switches can be globally edited
● The conguration of all endpoints (video sources) connected to the
attached Layer 3 Enhanced CCTV Switch can be globally edited.
Use this mode when conguring or adding additional servers to a
Closed IPTV system only. The switch is not secure in this mode, but it
allows the NVR to discover cameras and additional switches. Cameras
can be physically swapped around and congured by the user as
required.
Note: In Conguration mode, there is no registration of a camera fail. The cameras are either in a not
connected state or connected when present.
In Secure Mode;
● Closed IPTV security is enabled and the selected security settings
(determined by the conguration check boxes) are applied.
● End points (video sources) will become trusted for NetVu
Connected Cameras.
When in this mode access is restricted by a number of techniques,
including Restrict between end points, Restrict Public Access, Restrict
multicast from general network and Lock ports by MAC (below).
Note: In Secure Mode, video sources are either successfully connected or port free. A congured
source that is not sending data will be registered as a camera fail.
Intelligent Security & Fire Ltd
Page 59
59
Installation Guide
NOTE: Secure mode should always be enabled once conguration is complete. If left in Conguration
mode the system will be insecure and vulnerable to attacks. A visible warning will be displayed on
the local viewer if Secure mode is not applied.
Restrict between end point ports End points are dened as the extreme edges of the network, normally
video sources, which could be exploited as potentially insecure
connections into the Closed IPTV network.
This option acts as a hard rewall to stop exposed end points from
being used to mount attacks on other cameras in a different location
(e.g. prevents a camera in a public location from affecting a camera in
the safe vault).
Restrict public access (Port B) Select to restrict all network data between the General/Corporate
network to the video end points. No outside connections except
the NVR are allowed to communicate with end points directly, and
endpoints are separated from the General/Corporate Network..
Note: The NVR itself on standard DHCP or static IP address will still be accessible from Eth-B if
physically connected to network.
Note Non NetVu Connected cameras will only be allocated DHCP addresses by the external network if
this option is disabled.
Warning: Ifthisoptionisnotenableditwillstillbepossibleforexternalsystemsconnectedto
thegeneralcorporatenetwork(viaportEth-B)toaccessallcamera/videosources.
Dedicated Micros recommends that Eth-B should always be left restricted in Secure Mode
as security can be compromised if left unrestricted. Additional Closed IPTV systems should
always be added in Cong mode to allow auto IP conguration to accommodate existing
systems and avoid ip conicts.
Restrict multicast from
general network This disables client network access to the multicast services on
the camera, but does not disable standard web access for camera
conguration etc. unless ‘Restrict public access’ is also enabled. If this
option is ticked, it only allows clients to receive multicast video data
through SAP service group broadcasts from the NVR.
Warning: Multicasting requires this option is disabled to ensure public access is unrestricted.
Lock ports by MAC Camera ports on the Layer 3 Enhanced CCTV Switch can be locked to
the MAC address of the camera connected to that port. This prevents
casual access from the port to the rest of the system (DVR, other
cameras). No other MAC address will be allowed on that port.
This
allows multicast, direct camera access etc but protects the client network
to a limited degree from the exposed end point.
Signature Verify Remote Codecs More sophisticated attackers could bypass the Layer 3 Enhanced
CCTV Switch MAC address rules (described in ‘Lock Ports by MAC’) by
spoong the MAC address of the camera connected to the port. We can
identify such attackers using Trusted Endpoint Signature Verication of
the video stream.
Warning: If this option and ‘Lock ports by MAC’ is not enabled then cameras or other devices
can be swapped in and out of the port with no restrictions on their network data i.e. an
alternative ‘hacked’ video source could be introduced to the Layer 3 switch in place of a
legitimate source.
Intelligent Security & Fire Ltd
Page 60
60
NV4
Restrict End Point Access to NVR
To limit the potential intrusion methods available from the camera
ports, the standard set of TCP and UDP services on the NVR can be
completely disabled to trafc from the camera ports. If a camera has
been swapped for a device that has been given a spoof MAC address
the NVR will still only accept data from that connection via the usual
HTTP port. The port can only supply video, and this will be agged as
unsigned due to the Trusted Endpoint feature (if enabled).
Security Violations
Isolate from network On detection of a security breach this option will prevent any device
connected to the breached port from accessing the general corporate
network (if available). Video will continue to be streamed on the Closed
IP side of the network.Reconnect after Reconnection to the
network will be attempted after a security breach once this period has
elapsed. If the security breach is detected again, connection to the
public network will remain blocked.
Isolate from Closed IP If a security breach is detected, the video source is isolated from the
Closed IPTV network.
Generate system event
Select this option to report port violation as system events which can be
used as a input to an alarm zone (e-mail, alarm etc ) on the NVR
.
Overview (Red Button) Select to open the Camera -> Overview page.
Discover (Green Button) Select to open the Closed IPTV -> Discover page which can be used to
force discovery of all Layer 3 Enhanced CCTV Switches connected to
the NVR.
Unalloc (Yellow Button) Select to open the Camera->Unallocated Cams page.
Advanced (Blue Button) Select to o
pen the Closed IPTV->Advanced Page, refer to ‘Advanced’.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 61
61
Installation Guide
Discover
This page shows the currently connected switches and allows the option to force discovery of Layer 3
Enhanced CCTV Switches connected to the NVR. When a switch is connected, the NVR will automatically
discover and connect to it. The Layer 3 Enhanced CCTV Switch supports zero-conf networking
(sometimes known as Bonjour), which enables automatic discovery of cameras on the IP network. Zeroconf uses industry standard IP protocols to allow devices to automatically discover each other without the
need to enter IP addresses or congure DNS servers.
Variable The parameter being passed by the discovered switch. There is the
capability to show 16 switches, each switch detail is separated by a
comma.
Value Details the appropriate port variable value.
CIP Settings (Red) Select to open the Closed IPTV->Settings page
Discover (Green Button) Informati
on on the switches seen by the NVR is updated in the table
.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 62
62
NV4
Upgrade Switch
This page provides the option to upgrade a selected switch (or all switches). Upgrades for the
Layer 3 Enhanced CCTV Switch are included in the upgrade les for the NV4 and are loaded to the
switch from the NVR.
Once a switch is connected and auto-discovered, the connected NVR can upgrade it. Select the switch
to be upgraded and press the Upgrade button. The NVR sends the required le to the switch and
automatically restarts it.
Upgrade Switch Use the drop down to select the switch to be upgraded, or upgrade all
switches using the ‘All Switches’ option.
Progress The entry shows the status of the switch upgrade.
CIP Settings (Red) Select to open the Closed IPTV->Settings page.
Upgrade (Yellow) Begins the forced upgrade of the switch.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 63
63
Installation Guide
Advanced
This page allows access to the advanced facilities on the NVR such as Autosync and setting the base
camera number of a switch.
Auto-Synchronise NVR variables with cameras When a new camera is connected and the unit is in
conguration mode, the NVR will synchronise some
of the settings (eg camera title) with the
camera.
Synchronisation will only occur for Remote
Codec cameras
(ie NetVu Connected cameras/video servers) and only
in conguration mode.
Switch Displays the switches that have been found and
accepted by the NVR, refer to ‘Discover’.
Base Camera Each switch can have up to 16 video sources attached
to it. A switch may not have all ports congured with a
video source, so there may be more than two switches
attached to the NVR. This option sets the base camera
number on the selected switch, all subsequent video
sources on that switch will receive a consecutive
number.
Intelligent Security & Fire Ltd
Page 64
64
NV4
Note: Ports on the switches are allocated using a combination of base switch number and conguration
page. Each Layer 3 Enhanced CCTV Switch has a hardware conguration dial on the base to
allow a unique (in the cascade) identier to be set. This identier is used by this conguration
page to congure the base camera number.
Layer3 Enhanced
CCTV Switch
Layer3 Enhanced
CCTV Switch
Layer3 Enhanced
CCTV Switch
Layer3 Enhanced
CCTV Switch
KBD
USB
ETH-0
AUX AUD1
IN
VID 1
MON
B
VID 2 VID 3
SATA1
OUT
A
VID 8VID 6VID 4 VID 5 VID 7
ALARMS
RELAYS
SERIAL 1
SERIAL 2
SERIAL 3 PTZ
SERIAL 4 PTZ
AUX AUD2
IN
OUT
EXP
O
I
IR
SATA2
ETH-1
HDMI 1
AUD 1
AUD 2 AUD 3 AUD 4 AUD 5 AUD 6 AUD 7 AUD 8
HDMI 2
ETH-D
ETH-C
ETH-B
ETH-A
VID 9 VID 10 VID 11 VID 16VID 14VID 12 VID 13 VID 15
AUD 9
AUD 10 AUD 11 AUD 12 AUD 13 AUD 14 AUD 15 AUD 16
et V Serer
Cameras
Displays the camera numbers that have been assigned to
the switch by the Closed IPTV NVR. The NVR recognises
how many cameras are attached to the switch and assigns
cameras numbers accordingly
.
Example Settings
Scenario 1 - One switch - 16 Analogue cameras attached to NV4 CIP
Switch Hardware Setting No. of Cameras Base Camera Camera numbers
0 16 17 17-32
Scenario 2 - Two switches - 0 Analogue cameras attached to NV4 CIP
Switch Hardware Setting No. of Cameras Base Camera Camera numbers
0 16 1 1-16
1 16 17 17-32
Scenario 3 - Two switches - 8 Analog Cameras (ports 7-16)
Switch Hardware Setting No. of Cameras Base Camera Camera numbers
0 8 1 1-8
1 4 17 17-20
Scenario 4 - Three switches - 0 Analogue Cameras
Switch Hardware Setting No. of Cameras Base Camera Camera numbers
0 8 1 1-8
1 4 9 9-12
2 4 13 13-1
Scenario 5 - Four switches - Geographically dispersed IP cameras
Switch Hardware Setting No. of Cameras Base Camera Camera numbers
0 4 1 1-4
1 4 5 5-8
2 3 9 9-11
3 5 12 12-16
Note: Analogue cameras connected to the rear of the unit will take priority over IP cameras connected
via a Layer 3 Enhanced CCTV Switch. An IP camera connected into a channel that is occupied
by an Analogue camera will be ‘bumped’ onto the Unallocated Cameras list to allow it to be
assigned to a free channel.
CIP Settings (Red) Select to open the Closed IPTV->Settings page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 65
65
Installation Guide
Console Settings
The menus under the Console Settings heading allow the unit’s Viewer display settings to be altered and
User Account details to be viewed and changed.
The Systems Page page is used to congure which other video sources are visible through the console
facility on the NV4. This allows individual cameras, a range of cameras or all cameras from a server to be
arranged into one of the 20 systems available within the NV4. Each system can hold up to 99 cameras.
The Systems Overview page gives an overview of all connected cameras and their home servers across
all systems.
Note: The Systems Overview page can only be accessed if viewing the Conguration menus remotely
via an IP connection.
The Remote Monitors page allows monitors not physically connected to the unit to view camera images
received by the unit.
The Viewer Defaults page allows the Viewer menu settings to be congured.
The Display page controls how the local monitors present information. They control whether text will be
displayed on the Main or Spot monitors, the colour of that text, and how long cameras being displayed in
sequence will be shown on screen.
The Maps page allows images to be imported and used as maps displayed in the Viewer menus. Hot
spots can be added to allow quick navigation to individual cameras.
The Map Data page allows Map Cong information to be saved for future use. Previously saved data can
also be uploaded.
The User Accounts page helps protect conguration procedures by limiting access to specic users via
accounts and passwords.
Intelligent Security & Fire Ltd
Page 66
66
NV4
Systems
The unit can be congured with up to 20 systems. A system is a collection of DVRs and cameras selected
from those DVRs. Systems are not formally connected networks but a collection of DVRs viewable over
an IP network. Each system provides access and control of up to 99 cameras at any one time.
Each individual system can be selected from a drop down menu.
Camera numbering is sequential within that system (up to the maximum 99 cameras per system).
Note: Forlocalcamerafeedstofunctioncorrectly,ensuretherstserveroptionfor
System1isconguredtodisplaythelocalcamerasasshownbelow:
Server URL Server Name Camera Selection
localhost local 1-4, 1-8 or 1-16
System Select from 20 available systems using the drop down menu.
System Name If required, enter a recognisable name for the system (this name is held
on the NVR and represents the system).
Server URL Enter the IP addresses of the servers providing the video signals.
Server Name Enter a name for the accompanying requested server (this name is held
on the NVR and represents this server).
Camera Selection Select the cameras to be accessed. To select individual cameras, use
the format 1,3,5 or 1:3:5 etc. To select a range of cameras, use the
format 1-3 or 1_3 etc. All connected, non-covert cameras within the
range will be added in numerical connection order.
Intelligent Security & Fire Ltd
Page 67
67
Installation Guide
Auto Fill The ‘Auto Fill’ option will utilise the Server URL to automatically
populate the system with the server name and ALL available cameras
from that server.
Save (Grey) Select to save current unit settings.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 68
68
NV4
Systems Overview
This menu gives an overview of all connected cameras and their home servers across all systems. The
numbers allocated to each camera, both ‘locally’ within each System, and ‘remotely’ by the servers they
are attached to, are displayed. The Conguration pages for each connected server can also be accessed
(if access rights permit).
Note: This page will only be available if accessing the Conguration menus remotely i.e. via an
IP connection.
Local Cam Num Identies the number the camera is allocated in each system i.e. to
access Camera 1 in System 1, rst select System 1 via the System
Selection map, then select Camera 1.
Remote Cam Num Identies the number the camera is allocated on its server. Selecting
this number via the Viewer menus willnot result in images from that
camera being displayed.
Server URL Displays the URL of the server supplying the video images.
Server Name Displays the name of the server supplying the video images.
Congure Server Select the Cong Pages option (displayed here if applicable) to access
the conguration pages for the selected Server.
Note: Passwords may be required to successfully access server conguration pages.
Intelligent Security & Fire Ltd
Page 69
69
Installation Guide
Remote Monitors
This menu allows monitors on a separate, networked unit to display the camera images received by this
unit. The IP address of the server connected to the monitor (or video wall) is required. Cameras can then
be selected via the remote monitor.
Up to 32 remote monitors (or video walls) can be congured. Enter the IP address of the server connected
to the monitor.
Save (Purple) Select to save current unit settings to the selected media.
Intelligent Security & Fire Ltd
Page 70
70
NV4
Remote Monitoring Operation
POWER HDD NETWORK POWER HDD NETWORK
U1 U2
M2 M1
To view the cameras connected to U1 on a monitor connected to U2;
Enter the IP address of U2 into the Remote Monitor page on U1.
Intelligent Security & Fire Ltd
Page 71
71
Installation Guide
Viewer Defaults
This menu allows conguration of settings for the Viewer function. The Viewer function provides an
interface to connected cameras over a network which allows viewing and telemetry control, for more
information regarding this feature refer to ‘Operating The Viewer’.
Default settings can be congured for accessing the Viewer function via a local monitor and also remotely
via a network connection (settings can be optimised for either a LAN or WAN connection).
Default Image Format Images displayed in the Viewer menus can be shown in either JPEG or
MPEG format (MPEG is recommended for images that need to travel
over a network, JPEG requires a higher bandwidth and should be
reserved for higher capacity networks and local viewing only).
Default Full Req Images displayed full screen in the Viewer menus can be shown in
either High Medium or Low resolution.
Default Quad Req Images displayed in Quad format in the Viewer menus can be displayed
in either High Medium or Low resolution.
Default Multi Req Images displayed in Multi format in the Viewer menus can be displayed
in either High Medium or Low resolution.
Startup Multi Display When accessing the Viewer function, select the display format which
will initially be displayed.
Startup Multi Display When accessing the Viewer function, select the display format which
will initially be displayed.
Intelligent Security & Fire Ltd
Page 72
72
NV4
Startup Camera When accessing the Viewer function, select the camera image which
will initially be displayed. If one of the multi display formats has been
selected via the ‘Startup Multi Display’ option, the camera channel
selected here will be displayed in rst (top left) position. Subsequent
camera channels will be displayed in sequential order.
Video Output mode Select the display output that best suits the primary viewing monitor.
Typically PAL Default is most suited for a CRT monitor, PAL Reduced
for a TFT monitor.
Select from:
Safe Mode: Res: 640 x 512
PAL Default: Res: 704 x 512
PAL Reduced: Res: 640 x 512
HD Default: Res: 1280 x 720
HD 4x3: Res: 1280 x 720
HDMI Alternate 1: Res: 1280 x 688
HDMI Alternate 2: Res: 1216 x 688
HDMI Alternate 3: Res: 1192 x 676
HDMI Alternate 4: Res: 1264 x 716
HDMI Alternate 5: Res: 1220 x 690
HDMI Alternate 6: Res: 1216 x 688
Video Output mode 2 Select the display output that best suits the secondary viewing monitor,
the options available are the same as shown in ‘Video Output mode’
above.
Note: It will be necessary to reboot the unit to implement any change to the Video Output Mode. The
unit can be rebooted via the Reset (Red) option.
Note: If there is no suitable standard conguration to suit the monitor in use, refer to ‘Appendix F
->Monitor Output’ for details on enabling more options.
Decoder Mode Select from Normal Display or Decoder Mode. Normal Display allows
cameras to be accessed and controlled via the Viewer menu. In
Decoder Mode, connected cameras can be accessed, viewed or
controlled via Dedicated Micros Pick-a-Point system.
Note: For further information regarding Dedicated Micros Pick-a-Point system, please contact
Dedicated Micros customer services in your region.
Mouse Sensitivity The sensitivity settings of the mouse can be adjusted from the least
sensitive (1) to the most sensitive (10). The setting can be adjusted
via the slidebar or a number entered directly into the accompanying
textbox. The default setting is 4.
Applet Location The location of the unit’s Viewer menu applet is displayed. The default
location will always be the applet installed on the unit. If accessing
multiple units via a remote connection, all can be assigned the same
Viewer applet. This will lessen the load time required when accessing
different DVRs/Servers.
For example, if a local unit and a remote DVR are to be accessed, it is
possible to set the Applet location for both DVRs as the local unit.
If viewing the unit remotely, Dedicated Micros provide a remote
applet. This remote applet can be selected via the ‘Set Location’ option.
The applet is located on the website (www.dedicatedmicros.com/software_
release/index_rmware.php). Due to possible bandwidth restrictions on the
network the DVR is located, using this remote applet may improve data
transfer speeds.
Set Location Select the applet location. Choose from ‘Default location’ i.e. the applet
installed on the unit; or the ‘website’ option i.e. the
remote applet.
Intelligent Security & Fire Ltd
Page 73
73
Installation Guide
Reset (Red) Select to reset the unit and implement any changes made to the ‘Video
Output mode’ or ‘Applet Location’ elds.
Save (Purple) Select to save current unit settings to the selected media.
Intelligent Security & Fire Ltd
Page 74
74
NV4
Display
This menu allows conguration of monitor settings used when viewing camera images and text data.
Main monitor text It is possible to select text to be displayed on the main monitor. The
text displayed will include; time, date, mode of operation (Set, Unset or
Override), camera number and camera title.
Background Colour A black background appears by default around the text. It is possible to
change the colour of this background. Select from the options available
in the drop down list.
Text Colour The colour of the displayed text can be changed. Select from the
options available in the drop down list.
Sequence Dwell The sequence dwell time can be set from 5 to 99 seconds. The dwell
time is the period a camera’s images are displayed before switching to
the next camera in the sequence.
Sequence main on startup Select to sequence live views from all connected cameras on the main
monitor upon system start-up.
Softkey timeout (s) Controls how long the soft keyboard remains on screen if no input is
detected.
Numeric Input Timeout (s) Controls how long the numeric keypad remains on screen if no input is
detected.
Hide Mouse Cursor The mouse cursor can be hidden by enabling this option.
Intelligent Security & Fire Ltd
Page 75
75
Installation Guide
Enable custom segment setup Select to activate the custom segment setup feature. When selected,
the user can congure a Quad or Multiscreen layout via the Viewer
menu. The congured layout can include any camera in any available
segment.
Camera selection switches
to full screen Select to auto switch to full screen mode any camera channel selected
from multi-display (selected via the Viewer feature).
Select All (Blue) Select to add all available cameras to the Spot Monitor Sequence.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 76
76
NV4
Maps
This menu allows images to be imported and used as maps that can be displayed in the Viewer Menus.
The map can then have hotspots added to allow quick navigation to individual cameras.
An overview ‘System Selection Map’ can also be added to navigate between different systems.
Congure Map Select the relevant system using the drop down menu, or use the
‘Overall System Selection Map’ option to create a map to navigate
between systems.
The Overall System Selection Map will display all available numbered
systems. Selecting a hotspot then opens the relevant System camera
map.
Graphic Location Enter the location of the relevant map graphic, including the full
I.P address of the server holding the map. The map image will be
displayed if linking is successful. The linked map can be in gif or jpeg
format and should not exceed 500 by 350 pixels.
Map Screen Offset These co-ordinates represent the top left corner of the map graphic as
displayed in the Viewer menu.
Camera Select Select which camera is to be linked to the created hotspot.
Activate Hotspot Select to activate and display the camera hotspot.
Intelligent Security & Fire Ltd
Page 77
77
Installation Guide
Hotspot Radius Enter the radius (in pixels) of the hotspot.
Increment by If using the Decrement (Red) or Increment (Green) buttons, enter the
size (in pixels) that the hotspot will increase/decrease.
Decrement (Red) Select to reduce size of hotspot.
Increment (Green) Select to increase size of hotspot.
Hotspot X coord Use to position the centre of the hotspot along the X axis e.g. entering
20 would place the hotspot centre 20 pixels from the left edge of the
map.
Hotspot Y coord Use to position the centre of the hotspot along the Y axis e.g. entering
20 would place the hotspot centre 20 pixels from the bottom edge of the
map.
Note: The hotspot can also be positioned by clicking directly on the map.
Hotspot Origin (deg) This option should be used when the hotspot relates to a Dedicated
Micros Oracle Dome camera. Clicking the hotspot will send the
Oracle Dome camera to a pre-determined view (absolute positioning).
However if the dead centre of the hotspot is selected, the camera will
be viewed from its current location.
The absolute positioning point will depend on the data entered here.
A setting of ‘0’ would result in the camera facing its Original (base)
position. To change the preset position, enter a number between 1 and
360. A setting of 20 would set the preset position to 20 degrees to the
right of its ‘origin’ position, 180 would send it to face in the opposite
direction (of its base position) . For information on establishing an
Origin position for a PTZ camera, refer to the ‘Viewer Menus-PTZ
Prole menu‘.
Decrement (Red) Select to reduce size of hotspot.
Increment (Green) Select to increase size of hotspot.
Map Data (Yellow) Select to open the Display->Map Data page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 78
78
NV4
Map Data
The Map Data menu allows Map Cong data to be Imported/Exported. This enables map data to be
saved and stored for future use, or used between multiple NVRs.
Note: The Map Data menu will only be available when viewing the menu pages remotely i.e. via the
webpages.
To save map data, highlight and copy all text displayed in the Map Data text window, then save this data
as a text le.
To import data, copy relevant text from an external location and paste into the Map Data text window.
When the menu is exited, this data will be used as the Map Cong settings.
Note: Dedicated Micros recommend the existing Map Data is saved before import.
Map Cong (Blue) Select to open the Display->Map Cong page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 79
79
Installation Guide
User Accounts
The unit can protect conguration procedures by limiting access via usernames and passwords.
Account Types The available account types for which users and passwords can be
assigned privileges are:
• Admin FTP Assigning username and password
requirements for the Admin FTP
function will limit access to the unit via
an FTP connection.
• Video FTP Assigning username and password
requirements for the Video FTP function will
limit access to the Video FTP archiving feature
(used with NetVu ObserVer).
• Telnet Assigning username and password
requirements for Telnet connections will limit
Telnet access to the unit (Telnet can be used to
upgrade the unit).
• Serial Assigning username and password
requirements for Serial connections will limit
access via a Serial link.
• Menu Conguration Assigning Menu Conguration access privileges
will limit access to the Conguration menus
when viewed locally. When implemented, the
user will be prompted for a username and
password before access to the Conguration
menus (via the main menu) will be granted.
Intelligent Security & Fire Ltd
Page 80
80
NV4
• Local Users Assigning Local Users access privileges will
limit access to the Viewer pages for local users.
When implemented, the local user will be
prompted for a username and password before
access to the Viewer pages (via the main
menu) will be granted.
• Remote Users Assigning Remote Users access privileges will
limit access to the Viewer pages for remote
users. When implemented, the remote user
will be prompted for a username and password
before access to the Viewer pages (via the
main menu) will be granted.
It is possible when granting access privileges to Local and Remote Users to limit access to specic
cameras. Use the Camera Selection segment of the Add New Account menu, enter those cameras for
which access will be permitted. Select the cameras in accordance with the input channel connected to on
the rear of the unit. For example, to allow access to camera 1 to 3 inclusive, enter: 1-3. To grant access
to cameras 1,3 and 6, enter 1,3,6. If no camera data is entered, access will be allowed to all connected
cameras in both live and playback modes.
Note: There are no default usernames and passwords for any of the Account Types. If none are
assigned, access will be granted to all users and no request for a username and password will be
made.
Account List
When an Account Type is highlighted, details of users with access will be displayed.
Add Highlight an administration feature i.e. Serial and select ‘Add’. Enter the
new User Name and Password. That user’s name will now be displayed
in the account list.
Modify/Delete To modify or delete a user’s settings, highlight the user in the list and
press the relevant button to Modify or Delete.
Note: If viewing the User Accounts page via a local monitor and navigating with the I.R Remote Control.
Press the right directional button from the menu tree to access the Account List.
Enter the new User Name and Password. That user’s name will now be displayed in the account list.
Modify (Green) To modify user setting, highlight the user in the list and press to Modify.
Delete (Yellow) To delete a user, highlight the user in the list and press to Delete.
Intelligent Security & Fire Ltd
Page 81
81
Installation Guide
Camera Settings
The Camera Settings menus allow conguration of cameras connected to the unit. Refer to the individual
menus for further details.
The Camera Setup page allows the quick conguration of all connected local camera channels (with a
dynamic preview available).
The Camera Overview menu details the general settings assigned to each of the local
camera channels.
The Upgrade menu allows cameras connected to the Enhanced Layer3 CCTV Switch to be upgraded to
the latest version of available software from the NVR
The IP Streams menu allows the selection of High, Medium and Low resolution settings for video sources
originating from a network based source i.e. IP Server. These streams are congured on the remote
device. This feature is predominately intended for use with 3rd party IP camera streams (connected via
the 3rd party IP camera unlock feature).
The Intelligent PTZ menu details the Dedicated Micros Oracle Domes connected to the Closed IPTV
System.
The Unallocated Cams menu details the cameras that are available to the Closed IPTV system but are
not assigned to a camera channel. This will normally be because a BNC (Analog) camera has been
allocated the same channel as and IP camera, which has become automatically unallocated.
The Privacy Zones menu allows one area on each camera to be obscured on the local output from the
NVR. The mask is not transmitted over the network or recorded, but can be re-applied to local playback.
Intelligent Security & Fire Ltd
Page 82
82
NV4
Setup
Thismenu allows the conguration of active camera channels.
IMPORTANT: The menu options displayed will differ depending on the camera ‘Type’ and ‘IP Mode’
selected.
Note: Ideally any setup options available locally on the camera should rst be used to best obtain a
suitable image quality.
Mono/Colour Camera
Load Video Window (grey) Press to initiate the applet that will display the camera view.
Camera Select a camera channel for review and adjustment.
Camera Nuisance Count This is a repetitive detector value. When a camera failure alarm is
received on the unit, it will store the alarm time and monitor the number
of times the same alarm is triggered within an hour period. If the
detector is triggered the number of times entered here, the unit will set
the camera to ‘No Connection’. To disable this feature, leave the setting
as ‘0’.
Title Assign a recognisable name to the camera. This will be displayed in
all references to the camera in the both the Conguration and Viewer
menus.
Intelligent Security & Fire Ltd
Page 83
83
Installation Guide
Type The settings will default to ‘Colour’. If Monochrome cameras are used,
select ‘Mono’. Selecting ‘Mono’ will remove colour patterning. Select’
‘IP’ for an IP Camera. If a particular channel is not in use or the camera
has failed, select ‘No Conn’.
IMPORTANT: The menu options displayed will differ depending on the camera ‘Type’
selected here.
Fail Rep Select this option to generate a Failure report in the event of camera
connection failure.
Termination The input is automatically terminated, this setting should be disabled if
the video feed is looped through.
Telemetry If a telemetry capable camera is connected, the appropriate control
protocol should be selected from the accompanying drop down list,
refer to ‘Appendix I’ for details of supported
telemetry protocols.
Note: A serial port should be assigned if a serial protocol is used.
Default to preset If a telemetry camera has been assigned a preset position, select
the chosen preset position here. Enter the time period (in minutes) of
inactivity which will result in the camera moving to its preset position,
refer to Viewer menus->Program Page for guidance on assigning
camera presets.
after X mins This is the default setting referred to above in ‘Default to preset’.
Note: The following settings will change depending on the type of camera connected.
If a Local Analog Camera is selected
Colour Select a colour value from -8 to +8 via the slidebar or enter a number
directly into the accompanying textbox.
Brightness Select a contrast value from -8 to +8 via the slidebar or enter a number
directly into the accompanying textbox.
Intelligent Security & Fire Ltd
Page 84
84
NV4
IP Camera
If a NetVu Connected IP Source is selected
IP Type Select the type of NetVu Connected source the camera stream is
originating from. Select from:
‘NetVu Server’ - i.e. DVIP Server, DVIP RT, SD, DV-IP NV8
‘NetVu Gen 2’ - i.e. DS2, BX2.
NetVu Camera’ - i.e. the CamVu 2000 from Dedicated Micros.
‘NetVu ANPR’ - i.e. the HyperSense ANPR camera from
Dedicated Micros.
IP Mode Select the IP mode used to receive incoming IP data. Select from:
Simple Stream - Received IP streams are non-compressed and are
viewed as congured on the originating source.
Recode Stream - When selected, the unit will recompress the
incoming IP stream to the record prole settings
established for this camera channel in the Prole
Record menu (Record Settings->Prole Record).
This feature is only accessible with 3rd party IP
camera when the 3rd party IP camera license has
been enabled.
Intelligent Security & Fire Ltd
Page 85
85
Installation Guide
Remote codec When selected, the unit will utilise the codec in
the remote NetVu connected video server/camera
to allow change Multimode proles and perform
additional activities such as VMD and Activity
Detection as if the codec was an integral part of the
DVR. If ‘Remote codec’ is selected, the loading on
the unit’s internal codecs will be reduced.
IMPORTANT: The Remote codec option is only applicable for NetVu Connected cameras.
Note: Additional IP cameras (further to existing local camera channels) are remote codec only.
Therefore any NetVu connected cameras will be applied above local camera level.
When ‘Simple Stream’ and ‘Recode Stream’ are selected via ‘IP Mode’, the following options will
be available:
IP Address Enter the URL address of the image source.
Note: Typically this data will be automatically added.
Channel If the URL is a multichannel device (e.g. DV-IP NV1), this species
which channel to use.
Both types
Live Trans (Red) Select to open the Network->Live Trans page
View Prole (Green) Select to open the Record Settings->Prole Record page
Basic (Yellow) Select to open the Serial Ports->Camera page.
Lens Setup (Blue) Select to open the Camera Lens Conguration page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 86
86
NV4
Camera Lens Conguration
This page allows different lens de-warping techniques to be applied to connected cameras. The NVR can
de-warp Fish-eye and Depressive Fish-eye lenses to present a normal aspect image.
Title Shows the allocated name of the video source.
Lens Type Allows selection of sheye, depressive sheye and normal lens types.
Pitch Allows the image to be rotated counterclockwise by ninety degrees.
Ratio (H) Allows the horizontal ratio of a panamorphic lens to be set.
Ratio (V) Allows the vertical ratio of a panamorphic lens to be set.
Ratio x100 Allows the multiplier ratio of a panamorphic lens to be set.
Cam Setup (Red) Select to open the Camera -> Setup page
Cam Overview (Green) Select to open the Camera -> Overview page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 87
87
Installation Guide
Overview
This menu details the general settings assigned to each of the local camera channels.
To edit the settings assigned to any of these cameras;
Click on Local Camera Setup to edit the settings held in the DV-IP NV8;
Click on ‘Setup’ to open the Setup menu on the connected video source.
CIP Settings (Red) Select to open the Closed IPTV->Settings page
Unalloc (Green) Select to open the Camera->Unallocated Cams page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 88
88
NV4
Camera Upgrade
This menu allows cameras connected to an Enhanced Layer3 CCTV Switch to be upgraded to the latest
version of available software from the NVR. Insert the upgrade disc or USB into the NVR and select the
cameras to be upgraded via the interface pages. The Upgrade button will then send the updated les to
the selected camera.
Select All (Red) Select all displayed cameras
Deselect All (Green) De-select all displayed cameras
Upgrade (Yellow) Upgrade the selected cameras
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 89
89
Installation Guide
IP Stream Inputs
The IP Streams menu allows the selection of High, Medium and Low resolution settings for video
originating from a network based source i.e. IP Server. These streams are congured on the remote
device. This feature is predominately intended for use with 3rd party IP camera streams (connected via
the 3rd party IP camera unlock feature).
Note: The IP Stream needs to be set to Simple Streaming on Camera->Setup.
Note: There is only normal ‘non event’ recording for connected IP cameras.
Channel Select a camera channel for review and adjustment. Only those
cameras designated as ‘IP’ in the Camera Setup menu will be available
(Conguration menu: Camera->Setup).
Copy to all Select this option to apply current settings to all
connected cameras.
The following options can be congured for Set, Unset and Override record proles when operating
under Normal (non Event) conditions, refer to Conguration Menu:Record Settings->Prole Record for
information regarding record modes.
Comp Select image compression format (MPEG or JPEG).
Res For both MPEG and JPEG recording, select either High, Medium or
Low quality resolution settings.
Note: To view a local third party IP camera ‘live’, IP recording should be set to MPEG.
IP Camera (Yellow) Select to open the IP Camera Conguration menu.
Intelligent Security & Fire Ltd
Page 90
90
NV4
Schedule (Blue) Select to open the Schedule->Setup page
Refresh (Purple) Refreshes the information on the current page.
IP Camera Conguration
Channel Select a camera channel for review and adjustment. Only those
cameras designated as ‘IP’ in the Camera Setup menu will be available,
refer to Camera->Setup.
Mode Select the IP mode used to receive incoming IP data. Select from:
Simple Stream Received IP streams are non-compressed and are
viewed as congured on the originating source.
Recode Stream When selected, the unit will recompress the incoming
IP stream to the record prole settings established
for this camera channel in the Prole Record menu
(Record Settings->Prole Record). This feature is
only accessible with 3rd party IP camera when the
3rd party IP camera license has been enabled.
Remote codec When selected, the unit will utilise the codec in the
remote NetVu connected video server/camera as if
it was directly connected inside the DVR, allowing
the user to change Multimode proles and perform
additional activities such as VMD and Activity
Detection as if the codec was an integral part of the
DVR. If ‘Remote codec’ is selected, the loading on
the unit’s internal codecs will be reduced.
Intelligent Security & Fire Ltd
Page 91
91
Installation Guide
IMPORTANT: The Remote codec option is only applicable for NetVu Connected cameras.
Note: Additional IP cameras (further to existing local camera channels) are remote codec only.
Therefore any NetVu connected cameras will be applied above local camera level.
When ‘Simple Stream’ and ‘Recode Stream’ are selected via ‘IP Mode’, the following options will
be available:
URL Enter the URL address of the image source.
Port If required, edit the port input data. This will default to 80 (HTTP).
Chan If required, edit the channel input data.
PPS Edit the PPS (Pictures per Second) recording settings.
Recode Select to activate the recode option.
When ‘Remote Codec’ is selected via ‘IP Mode’, the following options will be available:
IP Address Enter the URL address of the image source.
Channel If required, edit the channel input data.
IP Camera (Yellow) Select to open the Camera->IP Stream Inputs page.
Camera (Blue) Select to open the Serial->Camera page.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 92
92
NV4
Intelligent PTZ
This section details the Dedicated Micros Oracle Domes connected to the system. Connected Oracle
domes will be listed in the drop down selector. Once selected, all the Oracle Dome conguration options
will be available through the NVR’s menus.
Note: The setting ‘Restrict public access’ (Eth B) must be enabled on Closed IPTV->Settings if using
Oracle IP domes in a Closed IPTV environment.
These pages are all documented in the manuals that accompany the Oracle Dome, also refer to
‘Appendix H - Oracle Dome Conguration’. The Oracle Dome manual can also be downloaded from the
Dedicated Micros website.
Intelligent Security & Fire Ltd
Page 93
93
Installation Guide
Unallocated Cams
Channels can be utilised by the BNC connections on the back of the unit OR by the sockets on the switch.
If an IP source is plugged into a channel occupied by a BNC connection, the BNC will take priority and
possess the channel, whilst the IP connection will be added to the un-allocated list, allowing it to be tied to
an available channel through this conguration page.
Similarly, if a BNC connection is assigned to an occupied IP channel, the IP camera will be ‘bumped’ onto
this list.
Cameras can then be assigned to a free channel, or dismissed as no longer required. A dismissed
camera can be added back into the un-allocated list by refreshing the connection (unplugging it from the
switch, and plugging it back in again).
Assign to: Displays all available unassigned camera positions.
Assign Assigns the associated IP stream to the selected camera.
Remove Entry Deletes the associated IP stream from the unallocated cameras list
CIP Settings (Red) Select to open the Closed IPTV->Settings page
Remove All (Green) Deletes all IP stream on the unallocated cameras list
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 94
94
NV4
Privacy Zones
Privacy Zones are designed to obscure an area of view from the local operator, without disrupting the
recorded images. The Privacy Zone is applied to the local output from the NVR and so is not available
in NetVu ObserVer or when a camera is Multicast. One Privacy Zone can be congured per camera,
allowing that area of the image to be obscured electronically. Privacy Zones are normally congured when
a camera is pointing towards a private residence, or into an area that should not be visible (eg toilet,
changing room). Privacy zones should currently only be congured on static cameras.
Note: When the Privacy Zone feature is implemented. The viewing software is commanded not to
display the privacy zone segment. The images are still recorded however. It is the responsibility
of the user to ensure all viewing applications support the privacy zone feature i.e. the viewer must
be able to read the meta data in the image header and suppress displaying the created privacy
zone.
How to congure a Privacy Zone
Use the mouse (either through the network interface of by plugging a USB mouse into the NVR and using
the local interface) to dene the area to be obscured by clicking on one corner of the zone to be obscured,
and then clicking again to dene the opposite corner.
Note: During Conguration, view the camera in different multi screen congurations to make sure the
mask covers the area to be obscured in all views.
Intelligent Security & Fire Ltd
Page 95
95
Installation Guide
Suppress Local Live This setting allows cameras to have the privacy zone disabled during
live viewing on the local monitor. Add individual cameras by listing them
separated by a comma, add an inclusive range of cameras using a
dash eg 1,2, 4-5, 8
Suppress Local Replay This setting allows cameras to have the privacy zone disabled during
playback on the local monitor. Add individual cameras by listing them
separated by a comma, add an inclusive range of cameras using a
dash eg 1,2, 4-5, 8
Suppress Network Live Images served by this unit to a second NVR, using the Remote Monitor
or Embedded Console feature, will have the Privacy Zone applied
to them. This setting can disable the Privacy Zone from live images
viewed on Embedded Consoles and Remote Monitoring servers.
Suppress Network Replay Images served by this unit to a second NVR, using the Remote Monitor
or Embedded Console feature, will have the Privacy Zone applied to
them. This setting can disable the privacy zone feature from recorded
video when viewed on Embedded Consoles and Remote Monitoring
servers.
Camera Use the drop down to select which camera to congure the privacy
zone for.
Reload Img (Red) Refreshes the camera view on the page
Clear (Green) Removes the Privacy Zone for that selected camera.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 96
96
NV4
Record Settings
The Record Settings menus allow conguration of the unit’s record functions. Record settings can
be congured for normal operation, on alarm, by schedule and for set holiday and weekend periods.
Selected video data can be saved and protected. Refer to the individual menus for further details.
The Default page allows the basic Recording settings to be edited.
The Prole Record page allows the recording conguration to be based on specic priorities. The record
rate and quality can be customised to respond appropriately to the alarms and time of day.
A high degree of control and exibility is possible using these options.
The JPEG Trigger page allows
conguration of the pre trigger feature (for cameras recording JPEG mode
only). When enabled, the pre-trigger feature will buffer and store alarm recording prior to an event trigger
The Holiday and Weekend page enables Set mode to be activated for individual dates i.e. public holidays
or weekends.
The Protect Video page allows previously recorded data to be protected and retained. If needed, all
recording can be halted and saved video deleted.
The AoE Setup page allows conguration of the units ATA over Ethernet (AoE) function. AoE is a network
protocol designed for simple high-performance access of storage devices over Ethernet networks.
Importantly the external storage device must be located on the same network as the unit.
Intelligent Security & Fire Ltd
Page 97
97
Installation Guide
Default
The unit has a range of pre-dened congurations available. As standard the unit can record at 6pps
MPEG4 for up to 120 days (dependent on model). Alternatively the unit can be congured for 2pps JPEG
recording on each camera or for MultiMode operation (note that this will result in the record duration
being determined by the time period the unit is in alarm).
Days Recording Displays the record duration possible using the
current conguration.
Timed Expiry (Days) Images recorded onto disk can be programmed to expire after a user-
dened number of days. This option is useful if you are required to
adhere to legislation on maximum recording time.
Warning: Once the timed expiry has been set, all images older than the selected time will be lost.
Default All (Green) This button sets all the camera recording settings back to the default
held on the NVR according to the type of camera.
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Page 98
98
NV4
Prole Record
It is possible to set the unit recording conguration based on specic priorities.
The MultiMode recording
feature offers the ability to set different recording rates, resolutions and compression formats across
unset, set and override modes for each individual camera. By varying the quality, bit rate and le
size of recorded images, the MultiMode function enables the recording capabilities of the unit to be
greatly increased. The Prole record menu can be accessed in a Simple format or in Advanced mode.
The Advanced mode offering greater opportunities to dynamically edit individual cameras recording
capabilities.
What is Turbo mode?
Turbo mode allows video images from any analogue camera or 3rd Party IP recoded camera to
be recorded and streamed at the maximum possible rate without the need to congure individual
settings. Turbo mode must be set Globally and will result in MPEG record rates of 12.5pps@4CIF and
25pps@2CIF/CIF/QCIF.
Note: When Turbo Mode is selected, there will be only ONE congurable Record Prole across ALL
cameras. The unit then matches the live transmission rate to the congured record rate. This
enables a ‘doubling’ of performance. Only the ‘Low’ and ‘Medium’ Live Transmission proles
are available for conguration (Network Settings->Live Transmissions). Low and Medium
transmission settings are congurable to allow video streaming over low bandwith IP connections
and are limited to CIF for this purpose.
Intelligent Security & Fire Ltd
Page 99
99
Installation Guide
Simple Record
Menu View Switch to the Advanced Prole Record menu.
IMPORTANT: If Turbo mode is ‘Disabled’ and record settings have been congured which will exceed
the unit’s Codec performance threshold. A warning message will be displayed informing
the user that the ‘Unit needs to be in turbo mode’. If the unit is currently in turbo mode
and the currently congured record settings do not warrant turbo mode, a message will
be displayed informing the user that ‘At the current settings the unit does not need to
be in turbo mode’. The codec’s performance thresholds are detailed in the About-Codec
Loading menu (System Settings->Status->About->Codec Loading)
Days Recording Displays the record duration possible using the current conguration.
Channel Enables selection of a specic camera for editing.
Copy To End Select to copy the current prole record settings to all camera channels.
Copy To Next Select to copy the current prole record settings to the next
camera channel.
Filter by Connected cameras are available to be sorted by resolution, select the
resolution of cameras to be displayed and congured.
Turbo Mode Select to activate the Turbo mode function (see ‘What is Turbo mode?’
for a description of Turbo mode and its benets).
Unset/Set/Override Normal Shows the recording prole used by the camera if no Timer Functions
are applied and the camera is operating under Normal (non Event)
conditions. Refer to the ‘Schedules’ section for further details.
Intelligent Security & Fire Ltd
Page 100
100
NV4
Unset/Set/Override Event Shows the recording quality that will be used by the camera during an
Alarm or Event. Note that Set and Override schedules will be used only
when Timed Schedules are applied. Refer to the ‘Schedules’ section for
further details.
Note: When Turbo mode is selected, there will be only ONE congurable Record Prole across ALL
cameras. The unit then matches the live transmission rate to the congured record rate. This
enables a ‘doubling’ of performance. Only the ‘Low’ and ‘Medium’ Live Transmission proles
are available for conguration (Network Settings->Live Transmissions). Low and Medium
transmission settings are congurable to allow video streaming over low bandwith IP connections
and are limited to CIF for this purpose.
Note: Unset, Set and Override modes can be given more recognisable titles i.e. Day, Night, Weekend
via the Schedule menu (Record Settings->Schedule).
Comp Select image compression format (MPEG, H264, JPEG).
PPS The accompanying dropdown list allows the number of frames captured
per second to be set.
The pictures per second (pps) option allows either 6, 5, 2, 1, 0.5, 0.25
or 0.1 pps to be recorded.
Pictures can also be recorded at ‘Real Time’ speed, ‘3/4 Real Time’ or
‘1/2 Real Time’.
To disable record, choose the ‘No Record’ option.
Select ‘User Dened’ to use settings established in the Advanced
Prole Record menu.
Quality The accompanying dropdown list allows the quality of recorded images
to be set. Select from Maximum, Very High, High, Medium, or Low.
Select User Dened to use settings established in the Advance Prole
Record menu.
Note: The higher the Quality setting, the greater the storage space used.
Codec Load (Red) Select to open the System->Status->About->Codec Loading page
Refresh (Purple) Refreshes the information on the current page.
Intelligent Security & Fire Ltd
Loading...