Installation Instructions
F ENCE POST
GATE
90˚
90˚
F ENCE POST
FENCE POST
SureClose ReadyFit
Model Hinge Type SF Hold Open Load
for Pool Gates Feature Bearing
74001313 RF SM S
74001315 RF SM W
74108313 RF 108 S
74108315 RF 108 W
74108323 RF 108SF S
74108325 RF 108SF W
GATE
FRAME
FENCE
POST
11
/64”
Pencil
(4.5mm)
DETERMINE LEFT OR RIGHT HANDED
1
ADJUSTMENT NOZZLES MUST BE POINTED UPWARD
Remove
4mm
4mm
5mm
7
1
(48mm)
5
/8”
/16”
(8mm)
Remove Gate Bracket
Adjustment Nozzles must be on top
Hi-Performance Hardware
Level
18V
B
A
Grease
Replace
4mm
2
4
A
VERIFY MODEL
( * see page 2 )
1
11
/64”
(4.5mm)
2
B
APPLY GREASE AND
RETURN TO REQUIRED
GATE GAP
FASTEN SCREWS INTO SLOTS ON
TOP AND BOTTOM HINGE
ENSURE GATE IS LEVEL
3
Remove hinge from mounting brackets before
welding to avoid damage. Use general field
v For Swimming
Pool Gates
in AU/NZ
(see Page 2)
welding operations with suitable heat transfer
controls.
See CAUTION advice on next page.
WELDING
GATE STOP
Support Blocks
A gate stop must be installed when using
SF models. Gate must not be allowed to
open past 90˚. Doing so voids warranty.
OPEN GATE AND FASTEN
5 6
SCREWS 5 AND 6
5
DETERMINE PROPER
VERTICAL ALIGNMENT AND
FASTEN SCREWS FIRMLY
3
5
/16”
(8mm)
4
6
INSTALL THE REST OF THE FASTENERS IN TOP AND BOTTOM
7
HINGES ON FACE AND SIDE LEGS
8
Use adjustment tool included or
wrench to adjust horizontally.
HORIZONTAL ADJUSTMENT
7
1
/8”
(48mm)
ReadyFit
Installation Instructions
ADJUSTING THE CLOSING SPEED
AND FINAL ‘SNAP’ ACTION
+
–
(S)
Hi-Performance Hardware
CAUTION: Sensitive adjustment, rotate 1/4 turn at a time.
V = Closing Speed
S = Final Snap Action
Turn nozzles clockwise to decrease speed & counterclockwise to increase speed.
If using two closers in combination, each closer
must have equal closing speed at all times.
(V)
Adjustment
Tool
Gate stop must be installed when using SF models.
Gate must not be allowed to open past 90˚.
Non-SF models open 180 o.
Hold-open from 180
Self-close from 85
NOT for child/pool safety gates.
MAINTENANCE REQUIREMENTS
• A gate stop must be installed when using SF models. Gate must not be allowed to
open past 90˚. Doing so voids warranty.
• Never use more than two (2) SureClose hinge/closers on any one gate.
• Remove all other types of hinges and self-closing devices.
• Always install SM hinge at bottom of gate and 57/108 closer on top.
• Ensure the gate does not swing through the line of the fence. Use a “gate stop”
or a latch (with striker) to prevent this.
• All steel mounting brackets (gate and post) should be painted or powder coated.
Spray painting is recommended.
• The anodized aluminum mounting brackets do not need nishing, but they may be
painted or powder coated.
• DO NOT powder coat the hinge/closer, but they may be painted.
• DO NOT turn the adjustment nozzles more than two (2) full rotations.
• DO NOT unscrew nozzle past the surface of the body.
• DO NOT remove the adjustment nozzles or disassemble these hinges at any time.
Doing so voids warranty.
• Ensure the hinges are kept free of sand, ice and other debris that could impair
effective operation.
o
to 90 o.
o
to 0 o.
IMPORTANT:
Use dimple to determine how far nozzle has turned.
DO NOT turn adjustment nozzles more than 2 complete rotations.
DO NOT unscrew nozzle past the surface of the body.
CAUTION:
DO NOT remove adjustment nozzles or disassemble hinge.
Doing so voids warranty.
Face of gate and
post are aligned
Final Snap Action
Increases speed
at end to ensure
lock engagement
SF models open to and self-close from 90 o.
NO hold-open feature.
Suitable for child/pool safety gates.
DO NOT PROP GATE OPEN.
2 YEAR LIMITED WARRANTY:
For a downloadable Adobe Acrobat (.PDF)
version of our 2 YEAR LIMITED WARRANTY,
go to our website at www.ddtechglobal.com
SF models have 5 dimples.
*
Remove from bracket to
verify before installation.
v Swimming Pool Gates
AU/NZ
CAUTION: When used on swimming
*
pool gates, always consult local
authorities for swimming pool Codes.
/2” (900mm) minimum
1
Distance between hinges 35
WELDING
CAUTION: Remove hinge from mounting brackets before welding to avoid damage.
Overheating any SureClose product during welding may cause failure and will void
warranty. Clean up and finish with appropriate corrosion protection, avoiding thread
contamination.
Patented: CA 2650769; US 7900319; NZ 573211;
AU2007245248, AU2011201042, AU2010280342, AU2011202070
Copyright 2013 D&D Group Pty Ltd, Sydney Australia
MANUFACTURED BY OLMI
PRECISION ENGINEERING
AUSTRALIA: Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086
USA: 7731 Woodwind Drive, Huntington Beach, CA 92647
EUROPE: Niasstraat 1, 3531 WR Utrecht, The Netherlands.
www.ddtechglobal.com
SCOLM000015PA USL 28/10/13
Loading...