DCS WOU130, WOSU30, WOUD230, WODU30 Installation Guide
Installation instructions
409 lb
186 kg
242 lb
110 kg
Wall oven
WOU130,WOSU30, WOUD230,WODU30 models
US CA
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website
www.dcsappliances.com or contact your local DCS Customer Care Representative.
1
SAFETY AND WARNINGS
Before you install the oven, please make sure that
The oven will rest on a surface that can support its weight.
The countertop and oven cavity are square and level, and are the required dimensions.
The height from the floor suits the user.
The oven door can open fully without obstruction.
Electrical requirements
Connect oven with copper wire only.
Do not cut the conduit.
A U.L. listed conduit connector must be provided at the junction box.
Do not ground to a gas pipe.
Do not have a fuse in the grounding or neutral circuit.
Fuse both sides of the line.
A time delay fuse or circuit breaker is recommended. If using a time delay fuse, then fuse both sides of the
line.
Flexible armored cable from the appliance should be connected directly to the junction box.
Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic
sheathed, copper cable (with grounding wire).
If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge are in accordance with local codes.
Do not use an extension cord with this appliance.
When you install the oven
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher &
Paykel will not cover the costs of removing the oven, or of damage caused by this removal.
Use the supplied screws to secure the oven to the cabinetry. Do not over-tighten the screws.
Do not stand on the door, or place heavy objects on it.
Do not lift the oven by the door handle.
Take extra care not to damage the lower trim of the oven.
WARNING!
Electrical hazard
Always disconnect the oven from
the mains electricity supply
before carrying out any
maintenance operations or
repairs.
Failure to do so may result in
electrical shock or death.
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
OVEN
DOUBLE
OVEN
SINGLE
WARNING!
MODELS
MODELS
WARNING!
Very Heavy
Do not attempt to lift this
product unassisted.
Lifting unassisted may
cause serious injury.
Important safety precautions!
Save these instructions for the local inspectors’ use.
To avoid hazard, follow these instructions carefully before installing or using this product.
Please make this information available to the person installing the product as it could reduce your
installation costs.
This oven is to be installed and connected to the electricity supply only by an authorized person.
If the installation requires alterations to the domestic electrical system, call a qualified electrician. The
electrician should also check that the socket cable section is suitable for the electricity drawn by the oven.
The oven must be grounded.
To connect the oven to the mains, do not use adapters, reducers or branching devices as they can cause
overheating and burning.
Installation must comply with your local building and electricity regulations.
Failure to install the oven correctly could invalidate any warranty or liability claims.
2
PRODUCT AND CABINETRY DIMENSIONS
3
PRODUCT AND CABINETRY DIMENSIONS
C
E
B
A
D
H
F
G
⁄” (2.5 mm) ⁄” (2.5 mm)
Installation diagrams for illustration purposes only
Product and cabinetry dimensions (inches (mm))
I
I
I
I
J
K
J
⁄-⁄”
(16-20 mm)
⁄-⁄”
G
(16-20 mm)
⁄” (2.5 mm)
Ensure the cavity is completely sealed with no gaps
WOU130
WOSU30
models
Double oven modelsSingle oven models
C
B
A
H
Product and cabinetry dimensions (inches (mm))
E
F
G
I
I
I
I
J
J
K
D
⁄-⁄”
(16-20 mm)
Ensure the cavity is completely sealed with no gaps
G
WODU30
models
⁄-⁄”
(16-20 mm)
⁄” (2.5 mm)
WOUD230
overall height of product 27 ⁄” (688)
A
overall width of product 29 ¾ ” (757)
B
overall depth of product (without handle) 23 ⁄” (608)
C
height of chassis 26 ¾ ” (675)
D
width of chassis 28 ¼ ” (718)
E
depth of chassis 22 ⁄” (570)
F
depth of oven frame and control panel (excl. knobs) 1 ½ ” (38)
G
depth of oven door (open) (measured from front of oven frame) 20 ⁄” (530)
H
minimum inside width of cavity 28 ½ ” (724)
I
I
overall width of cabinetry 30” (762)
I
inside height of cavity 26 ⁄” (681)
J
I
overall height of cabinetry 27 ⁄” (693)
J
minimum inside depth of cavity 22 ⁄” (575)
K
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the
cooktop manufacturer’s instructions.
overall height of product 48 ⁄” (1230)
A
overall width of product 29 ¾ ” (757)
B
overall depth of product (without handle) 23 ⁄” (608)
C
height of chassis 47 ⁄” (1217)
D
width of chassis 28 ¼ ” (718)
E
depth of chassis 22 ⁄” (570)
F
depth of oven frame and control panel (excl. knobs) 1 ½ ” (38)
G
depth of oven doors (open) (measured from front of oven frame) 20 ⁄” (530)
H
minimum inside width of cavity 28 ½ ” (724)
I
I
overall width of cabinetry 30” (762)
I
inside height of cavity 48 ⁄” (1222)
J
I
overall height of cabinetry 48 ⁄” (1235)
J
minimum inside depth of cavity 22 ⁄” (575)
K
UNPACK THE OVEN AND REMOVE THE DOOR(S)
4
Double models featured for illustration purposes only
A
B
1
1
5
ELECTRICAL CONNECTION TO JUNCTION BOX
Junction box location
for: undercounter
installation
Junction box
location for:
wall installation
1
Disconnect the power supply.
2
Remove the junction box cover.
3
Connect the oven cable to the junction box
through the U.L.-listed conduit connector.
4
Connect the two black wires together with
twist-on connectors.
5
Connect the two red wires together with
twist-on connectors.
6
Connect electrical connection according to
local codes and ordinances.
WOU130,WOSU30
Max. current draw: 19.4 A
Max. load: 4.6 kW
WOUD230,WODU30
Max. current draw: 38.3 A
Max. load: 9.2 kW
If local codes permit connecting the cabinetgrounding conductor to the neutral white wire
in the junction box:
7a
Connect the factory-taped green and white oven
cable wires to the neutral (white) wire in the
junction box.
8a
Replace the junction box cover.
Nameplate
4
1
4
red wires
white and green
grounding oven
wires - factory
taped
OR If local codes DO NOT PERMIT
connecting the cabinet-grounding
conductor to the neutral (white) wire in
junction box:
7b
Separate the factory-taped green and white
oven cable wires.
8b
Connect the white oven cable wire to the
neutral (white) wire in junction box.
9b
Connect the green grounding oven cable
wire to a grounded wire in the junction box.
10b
Replace the junction box cover.
3
cable from
power supply
box
black
wires
UL - listed
conduit connector
7c
Separate the green and white oven cable wires.
8c
Connect the white oven cable wire to the
9c
Connect the green grounding oven cable wire
Do not connect the green grounding wire to
10c
red wires
green grounding
oven wires
- factory taped
UL - listed conduit
connector
OR If connecting to a four-wire electrical
system:
neutral (white) wire in junction box.
to the (green) grounding wire in the junction
box.
the neutral (white) wire in junction box.
Replace the junction box cover.
2
cable from
power supply
box
white
wires
black
wires
Loading...