DATEL DMS-20PC-4-20S, DMS-20PC-4-20P, DMS-20PC-4-20B Datasheet

DATEL, Inc., Mansfi eld, MA 02048 (USA) • Tel: [phone] Fax: [phone] • E–mail: [e-mail] • Internet: www.datel.com

Actual Size

DMS-20PC-4/20 Series

The DMS-20PC-4/20 Series are the world's fi rst loop-powered digital panel meters
with a large, easy-to-read, bright red, LED display. All operating power is derived
directly from the loop current itself—no external power supply is required! The large,

0.37"/9.4mm digits exhibit uniform intensity over the entire 4-20mA operating range.
Additionally, the total maximum loop voltage drop is only 5V! Users no longer have to
settle for diffi cult-to-read LCD displays in loop-powered applications.

Both gain (span) and offset (zero) adjustments are performed with on-board, preci­sion, 20-turn potentiometers. All decimal-point and range-change selections are
made on a six-position DIP switch featuring vibration-resistant, gold-plated contacts.
Unlike competitive meters, there are no jumpers or solder gaps to open or close.
Connections to the current loop are made via a reliable, two-position, screw-type
terminal block.

The DMS-20PC-4/20's DIP switch and adjustment potentiometers accommodate
hundreds of different input-current/output-reading combinations. This versatility practi­cally eliminates the need to order more costly, long-lead-time, factory-customized "spe­cials" in applications in which several different-range meters are required. An optional
bezel assembly, featuring screw fasteners and a rubber seal, simplifi es panel mounting
and provides excellent resistance to environmental dust and moisture. All these out­standing features combine to make the DMS-20PC-4/20 Series the perfect meters for
prototype and OEM 4-20mA current-loop instrumentation.

Subminiature

4-20mA Loop-Powered

3½ Digit, LED ProcessMonitors

Figure 1. DMS-20PC-4/ 20 Series Simplifi ed Schematic

Features

• Industry's fi rst loop-powered meter

with a large, easy-to-read, LED display!

• Self-powered, no external

supply required

• Unipolar, Bipolar and Positive Reading

Models

• Large, 0.37"/9.4mm digits

• Excellent display intensity

• Constant 5V max. total loop drop

• High-quality, 20-turn, span (gain) and

zero (offset) adjustments

• DIP-switch selectable range and

decimal points

• Hundreds of input/readout combinations

• Vibration-resistant package; Reliable

screw-terminal input connections

New! Bipolar and Positive Reading Models

®®

Order online at www.datel.com

DATA

3½ DIGIT A/D
CONVERTER

DC/DC

CONVERTER

BAND-GAP

REFERENCE

CIRCUIT

DIP SWITCHES

ZERO

ADJUST

GAIN

ADJUST

1

2

3

CURRENT TO

VOLTAGE

CONVERTER

+5V –5V

DP3DP2DP1

R3 R7

+–

TB1

LOOP INPUT

1

2

3

45

6

ON

–+

3½ DIGIT, LED DISPLAY, 4-20mA LOOP-POWERED METERS

DMS-20PC-4/20

2

DATEL, Inc., Mansfi eld, MA 02048 (USA) • Tel: [phone] Fax: [phone] • E–mail: [e-mail] • Internet: www .datel.com

Operating and Setup Instructions

Performance/Functional Specifi cations

Typical at TA = +25°C, unless otherwise noted.

➀ The DMS-20PC-4/20, using any of the DIP-switch settings described above, can

withstand overcurrents, including those resulting from accidental reverse-polarity
connections, up to ±40mA without sustaining any damage.

➁ Because DATEL's DMS-4/20 loop-powered meters employ active circuitry to con-

vert the loop current into a voltage, the meters' effective series impedance varies
in a manner that maintains the loop voltage drop constant over the full 4-to-20mA
current range. Listed impedance specifi cation applies at 20mA.

➂ When looking up DIP-switch settings in the Tables and the desired display readings

can be achieved with either of two different settings, using the higher setting # will
produce less sensitive offset (R3) and span (R7) adjustments. Please keep in mind
that the DMS-20PC standard meter (from which the DMS-20PC-4/20 is derived)
has an accuracy specifi cation of ±2 counts (max.). Thus, it may not always be
possible to obtain the exact desired display reading.

1. Set R7 (full scale span/gain adjust) and R3 (zero/offset adjust) fully

clockwise, roughly 22 turns, and place SW1-SW6 to OFF.

2. Select DIP switch setting #2.

3. Apply a precision 4mA input, with proper polarity, and adjust R3 until

the meter's display reads "000".

4. Apply a precision 20mA input and adjust R7 until the meter's display

reads "1000". Repeat steps 3 and 4 to make sure the adjustments do

not affect one another.

5. Select the appropriate decimal point by setting SW4, SW5 or SW6 to

ON (DP1, DP2 or DP3 respectively).

NOTE: If a display reading other than "000" to "1000" is desired,

refer to DIP–Switch Settings Table 1 for SW1–SW3 settings.

Current Loop Input Min. Typ. Max. Units

Full Scale Input Range ➀ +4 –– +20 mA
Input Impedance ➁ –– 250 –– Ω
Voltage Drop ➁ –– 4.5 5.0 Volts
Overcurrent Protection ➀ –– –– ±40 mA

Performance

Sampling Rate 2.5 readings per second

Accuracy (1 minute warm–up) ±0.05%FS ±1 Count

Temperature Drift (0 to +60°C) –– ±0.15 ±0.3 Cnts/°C

Display

Display Type and Size 3½ digit, red LED, 0.37"/9.4mm

Polarity Indication "–" for negative readings

Overrange Indication "–1_ __ " for negative inputs

"1 _ __ " for positive inputs

Physical/Environmental

Operating Temperature 0 –– +60 °C

Storage Temperature –40 –– +75 °C

Humidity (Non–condensing) 0 –– 95 %

Case Material Polycarbonate

Weight 0.6 ounces (17 grams)

Display Reading SW1 SW2 SW3

4mA 20mA

1. 000 to 1050-1999 Off Off Off

2. 000 to 650-1350 On Off Off

3. 000 to 450-800 Off On Off

4. 000 to 300-500 Off Off On

5. 000 to 200-300 On On On

Table 1. DMS-20PC-4/20S (Unipolar Model) DIP-Switch Settings

DMS-20PC-4/20S Unipolar reading, loop-powered LED meter
DMS-20PC-4/20B Bipolar reading, loop-powered LED meter
DMS-20PC-4/20P Positive reading, loop-powered LED meter
DMS-BZL3 Bezel assembly
DMS-BZL4 Bezel assembly with sealing gasket
DMS-20-CP Panel cutout punch

A panel-mount retaining clip is supplied with each model.

1. Desired display readings are:

4mA ="0.00"

20mA = "6.00"

Use DIP-switch setting #3 in Table 1 and enable decimal point DP2

via SW5. Apply 4mA and adjust R3 so the display reads "0.00". Apply

20mA and adjust R7 so the display reads "6.00".

2. Desired display readings are:

4mA = "000"

20mA = "800"

Use DIP-switch setting #2 in Table 1. Apply 4mA and adjust R3 so the

display reads "000". Apply 20mA and adjust R7 so the display reads

"800". For these display readings, no decimal points are used. Set

SW4, SW5 and SW6 to OFF.

3. Desired display readings are:

4mA = ".000"

12mA = ".250"

This example is not as straightforward as the previous two. Notice that

12mA is exactly halfway between 4mA and 20mA. If we assume that

the input could go up to 20mA, the display reading would then be:

2 x .250 or ".500". From Table 1 we can now select DIP-switch

setting #4 and enable DP1 via SW4. Apply 4mA and adjust R3 so

the display reads ".000". Apply 12mA and adjust R7 so the display

reads ".250".

Examples (DMS-20PC-4/20S-Unipolar Model)

DMS-20PC-4/20S (Unipolar Reading Model)

As shipped, the DMS-20PC-4/20S is factory calibrated to read "000"

for a 4mA input and "1000" for a 20mA input. The following worst-case

procedure assumes the DMS-20PC-4/20S is completely mis-adjusted, i.e.,

both potentiometers and the DIP switches are randomly set. When perform-

ing DIP-switch settings, be sure the DIP switch's small actuators are fi rmly

engaged in their fully-ON or fully-OFF positions.

1

2

3

4

56

ON

123

4

5

6

ON

1234

56

ON

Ordering Information

3½ DIGIT, LED DISPLAY, 4-20mA LOOP-POWERED METERS

DMS-20PC-4/20

3

DATEL, Inc., Mansfi eld, MA 02048 (USA) • Tel: [phone] Fax: [phone] • E–mail: [e-mail] • Internet: www .datel.com

DMS–20PC–4/20B (Bipolar Reading Model)

The DMS-20PC-4/20B's zero-offset circuit differs from the unipolar 'S' model

described above in that with the 'B' model, a half-scale 12mA input is

normally set to display "000". Therefore, all of the of the DIP-switch settings

in Table 2 assume a reading of "000" is desired with a 12mA input. Display

readings other than those shown in Table 2 are possible, contact DATEL

for more information.

When confi guring the DMS-20PC-4/20B for the fi rst time, or when selecting

a new range, set both R3 and R7 fully clockwise (roughly 22 turns) to

their minimum offset/minimum-span positions, respectively. Then select the

desired readings from Table 2 and confi gure DIP-switches SW1, SW2, and

SW3 accordingly.

The procedure below illustrates how to calibrate the DMS-20PC-4/20B to its

factory-calibrated readings of "–1000" with a 4mA input and "1000" with a

20mA input. When performing DIP-switch settings, be sure the DIP-switch's

small actuators are fi rmly engaged in their fully-ON or fully-OFF positions.

1. Set both R3 and R7 fully clockwise.

2. Select DIP-switch setting #1 from Table 2.

3. Apply a precision 12mA input and adjust R3 until the meter's display

reads "000".

4. Apply a precision 20mA input and adjust R7 until the meter's display

reads "1000".

5. Apply a precision 4mA input and the display should read "–1000".

Repeat steps 3 and 4 to make sure the two adjustments did not

affect one another.

Examples (DMS-20PC-4/20B-Bipolar Model)

1. Desired display readings are:

4mA = "–1.00"

20mA = "1.00"

Use DIP-switch setting #5 in Table 2 and enable decimal point DP2 via

SW5. Apply 12mA and adjust R3 so the display reads "0.00". Apply

20mA and adjust R7 so the display reads "1.00". Apply 4mA and verify

that the display reads "–1.00", readjust R3 and R7 if necessary.

2. Desired display readings are:

4mA = "–450"

20mA = "450"

Use DIP-switch setting #2 in Table 2. Apply 12mA and adjust R3 so

the display reads "000". Apply 20mA and adjust R7 so the display

reads "450". Apply 4mA and verify that the display reads "–450".

Repeat adjustment procedure if necessary. For these display readings,

no decimal points are used. Set SW4, SW5 and SW6 to OFF.

3. Desired display readings are:

4mA = "–650"

20mA = "650"

Notice that these readings can be obtained using either DIP-switch

setting #1 or DIP-switch setting #2 in Table 2. In situations like this

where DIP-switch settings overlap, less-sensitive R3/R7 adjustments

can be achieved if the higher DIP-setting # is selected (setting #2 in

this example). Apply 12mA and adjust R3 so the display reads "000".

Apply 20mA and adjust R7 so the display reads "650". Apply 4mA and

verify that the display reads "–650". Repeat adjustment procedure if

necessary.

Display Reading SW1 SW2 SW3

4mA 12mA 20mA

1. –600 to –1000 000 600 to 1000 Off Off Off

2. –350 to –650 000 350 to 650 On Off Off

3. –250 to –400 000 250 to 400 Off On Off

4. –150 to –250 000 150 to 250 Off Off On

5. –100 to –150 000 100 to 150 On On On

Table 2. DMS-20PC-4/20B (Bipolar Model) DIP-Switch Settings

DMS-20PC-4/20P (Positive Reading Model)

The DMS-20PC-4/20P’s Zero-Offset circuit is optimized to produce positive

readings at both 4mA and 20mA input levels. As shown in Table 3’s fi rst

three columns, a 4mA input can be typically adjusted (using R3, Zero/Offset

Adjust) to display any positive reading between “000” and “800”. The cor-

responding 20mA-input reading is then added to the 4mA offset as a

differential whose magnitude is varied by adjusting R7 (Gain/Span Adjust).

The ‘Differential Range’ column in Table 3 lists the nominal differential

display-readings which can be obtained with R7 at, or very close to, its

full-clockwise, minimum span position. The Differential Range column can

be used as a guide when confi guring the meter for the majority of user

applications. Higher differential ranges are obtainable; however, the use

of higher differential readings results in correspondingly-lower positive read-

ings with 4mA inputs, that is, R3’s clockwise adjustment-range is reduced.

Example #3 below illustrates this concept. Please contact DATEL if there is

any doubt as to whether or not the DMS-20PC-4/20P can be confi gured for

your display readings requirements.

The fi rst step when confi guring the DMS-20PC-4/20P for the fi rst time, or

when selecting a new range, is to set R3 fully counterclockwise and R7

fully clockwise (roughly 22 turns) to their minimum offset/minimum span

positions, respectively.

The next step is to calculate the required display differential-reading; this

is accomplished by subtracting the desired 4mA display reading from the

desired 20mA display reading, disregarding decimal points. Then, using

the calculated differential display-reading to select the appropriate DIP-

switch setting # from Table 3, confi gure DIP-switches SW1, SW2, and SW3

accordingly. Make certain that the DIP-switch’s small actuators are fi rmly

engaged in their fully-ON or fully-OFF positions.

The procedure below describes how to calibrate the meter for an appli-

cation which the DMS-20PC-4/20P easily accommodates: displaying the

output of a 4-20mA transmitter, that is, “04.0” with a 4mA input and “20.0”

with a 20mA input.

1234

56

ON

123

4

5

6

ON

123

4

5

6

ON

3½ DIGIT, LED DISPLAY, 4-20mA LOOP-POWERED METERS

4

DATEL, Inc., Mansfi eld, MA 02048 (USA) • Tel: [phone] Fax: [phone] • E–mail: [e-mail] • Internet: www.datel.com

DMS-20PC-4/20

1

2

3

4

56

ON

1. Desired display readings are:

4mA = “650”

20mA = “950”

Use DIP-switch setting #4 in Table 3 since subtracting 650 from 950

yields a differential value of 300. Apply 4mA and adjust R3 until the

display reads “000”. Apply 20mA and adjust R7 until the display reads

“300” (the differential value previously calculated). Apply 4mA and

adjust R3 until the display reads “650”. Apply 20mA and verify that the

display reads “950”.

2. Desired display readings are:

4mA = “4.00”

20mA = “19.99”

This example illustrates the DMS-20PC-4/20P’s capability to display

higher differential readings than those indicated in Table 3. This exam-

ple also illustrates how the DMS-20PC-4/20P can be used to display

the output levels of a 4-20mA loop transmitter with higher precision

(0.01mA versus 0.1mA) than described above.

Subtracting 400 from 1999 yields a differential of 1599, a value not

listed in Table 3. However, use DIP-switch setting #1 in Table 3 since

this setting has the highest overall offset/span adjustment capabilities.

Enable DP2 via SW5 then apply 4mA and adjust R3 so the display

reads “0.00”. Apply 20mA and adjust R7 so the display reads “15.99”.

Apply 4mA and adjust R3 until the display reads “4.00”. Apply 20mA

and check to see that the display reads “19.99” or just overranges

(“1—“). Repeat adjustment procedure if necessary.

Figure 2. Typical DMS-20PC-4/20 Connection Diagram

1. Set R3 fully counterclockwise (minimum offset position) and R7 fully

clockwise (minimum differential span position), roughly 22 turns.

2. Subtract 040 from 200 to yield a differential value of 160; use this value

to select DIP-switch setting #5 in Table 3. Enable decimal point DP3 by

placing SW6 to the ON position.

3. Set the transmitter’s output to 4.0mA and carefully adjust R3 clockwise

until the meter’s display reads “000”.

4. Set the transmitter’s output to 20.0mA and adjust R7 counterclock-

wise until the meter’s display reads “16.0”.

5. Set the transmitter back to 4.0mA and slowly adjust R3 clockwise until

the display reads “04.0”. Reapply 20.0mA and the display should now

read “20.0”. Repeat steps 3, 4 and 5 to make sure the adjustments did

not affect one another.

Examples (DMS-20PC-4/20P-Positive Model)

Table 3. DMS-20PC-4/20P (Positive Reading Model)
DIP-Switch Settings

Differential Range 4mA Input 20mA Input

Display Reading SW1 SW2 SW3

➀ Shown for illustrative purposes only, may not be present in all applications

➀

Table 4. Decimal Point Settings

SW4 SW5 SW6

DP1 DP2 DP3

1. 800-1400 900 1700 Off Off Off

2. 500-800 850 1350 On Off Off

3. 350-500 800 1150 Off On Off

4. 250-350 750 1000 Off Off On

5. 150-250 750 900 On On On

1234

56

ON

A/D

+

––

+

–

Vsig

+

–

GAIN

ZERO

+24V

4-20mA

4-20mA

+

–

+

(TB1-1)

R7

R3

(TB1-2)

+24Vdc
SUPPLY

T

RANSDUCER

INPUT

TRANSMITTER &

SIGNAL CONDITIONER

PROGRAMMABLE

LOGIC CONTROLLER

DMS-20PC-4/20

DATEL, Inc. 11 Cabot Boulevard, Mansfi eld, MA 02048-1151
Tel: [phone] [phone] Fax: [phone]
Internet: www.datel.com Email: [e-mail]
Data sheet fax back: [phone]

DATEL (UK) LTD. Tadley, England Tel: [phone]
DATEL S.A.R.L. Montigny Le Bretonneux, France Tel: [phone]
DATEL GmbH München, Germany Tel: [phone]
DATEL KK Toky o , Japan Tel: [phone], Osaka T el: 6-354-2025

DA TEL mak es no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do
not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. The DATEL logo is a registered DATEL, Inc. trademark.

DS-0353D 02/01

3½ DIGIT, LED DISPLAY, 4-20mA LOOP-POWERED METERS

®®

DMS-20PC-4/20

Mechanical Specifi cations

MECHANICAL DIMENSIONS: Inches (mm)
TOLERANCES: 2 PL DEC ±0.02 (±0.51)

3 PL DEC ±0.010 (±0.254)
WIRE SIZE: 18 to 26 AWG
(Solid or stranded)
STRIPPING LENGTH: 0.20" (5.08mm)

Back View

Front View

DIP

Switches

Gain/Span

Adjust

Zero/Offset

Adjust

Loop
Input

DP2

(SW5)

DP3

(SW6)

DP1

(SW4)

0.80

(20.3)

0.040

(1.02)

1.30

(33.0)

1.38

(35.1)

0.88

(22.4)

0.95

(24.1)

MADE IN USA

DMS-20PC-4/20S

R3

R7

12

1

1

2

3

4

5

6

+–

1

2

3

4

5

6

ON

12

+ -

®®

RETAINING CLIP INSTALLATION

PANEL

®®

BEZEL INSTALLATION

BEZEL

PANEL

#2-56 INSERT

0.156 (3.96) DEEP

FRONT VIEW

1.280

(32.51)

0.187
(4.75)

DMS-BZL4 BEZEL

RECOMMENDED DRILL AND PANEL CUTOUT DIMENSIONS

1.826 (46.38)

0.838

(21.29)

1.350 (34.29)

*

1.626 (41.30)

1.07

(27.18)

INTERNAL CORNER RADII:

0.032 (0.81) MAX.

0.138 (3.51)

*

0.093 (2.362) DIAMETER (4 REQUIRED)
ONLY WHEN USING OPTIONAL BEZEL ASSEMBLY

0.116 (2.95)

1.336 (33.93)

0.145 (3.68)