Datasheet VN330SP-E Datasheet (ST)

Features

VN330SP-E

Quad high side smart

Power solid state relay

Typ e

VN330SP-E

1. Per channel.

2. At TJ = 85°C

■ Output current : 0.7A per channel

■ Digital input clamped at 32V minimum voltage

■ Shorted load and overtemperature protections

■ Built-in current limiter

■ Undervoltage shut-down

■ Open drain diagnostic output

■ Fast demagnetization of inductive loads

■ Conforms to IEC 61131-2

V

demag

V

CC

(1)

-55V

R

DSon

0.32Ω

(1)

(2)

I

(1)

V

out

0.7A 36V

CC

Figure 1. Block diagram

PowerSO-10

TM

Description

The VN330SP-E is a monolithic device made
using STMicroelectronics VIPower technology,
intended for driving four indipendent resistive or
inductive loads, with one side connected to
ground. Active current limitation avoids dropping
the system power supply in case of shorted load.
Built-in thermal shut-down protects the chip from
overtemperature and short circuit. The open drain
diagnostic output indicates overtemperature
conditions.

March 2007 Rev 3 1/15

www.st.com

15

Contents VN330SP-E

Contents

1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5 Switching time waveforms and truth table . . . . . . . . . . . . . . . . . . . . . . . . . 8

6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2/15

VN330SP-E Maximum ratings

1 Maximum ratings

Table 1. Absolute maximum rating

Symbol Parameter Value Unit

V

-V

I

OUT

I

I

I

DIAG

V

ESD

E

P

TJ Junction operating temperature Internally limited °C

T

STG

Power supply voltage 45 V

CC

Reverse supply voltage -0.3 V

CC

Output current (continuos) Internally limited A

Reverse output current (per channel)

R

Input current (per channel) ± 10 mA

IN

-6

Diag pin current ± 10 mA

Electrostatic discharge (R = 1.5KΩ; C = 100pF) 2000 V

Single pulse avalanche energy per channel not simultaneously

AS

Figure 4.

Power dissipation at Tc = 25°C

tot

400 mJ

Internally limited w

Storage temperature -55 to 150 °C

A

Table 2. Thermal data

Symbol Parameter Max Value Unit

R

thJC

R

thJA

1. Per channel

2. When mounted using minimum recommended pad size on FR-4 board

Thermal resistance junction-case

Thermal resistance junction-ambient

(1)

(2)

Max 2 °C/W

Max 50 °C/W

3/15

Pin connections VN330SP-E

2 Pin connections

Figure 2. Connection diagram (top view)

Figure 3. Current and voltage conventions

VCC

VIN1

VIN2

VIN3

VIN4

IIN1

IIN2

IIN3

IIN4

IDIAG

VDIAG

9

8

7

6

IN2

IN3

IN4

DIAG

10

IN1

GND

V

CC

11

IOUT1

OUT1

OUT2

OUT3

OUT4

5

1

2

3

4

IOUT2

IOUT3

IOUT4

VOUT1

VOUT2

VOUT3

VOUT4

4/15

VN330SP-E Electrical characteristics

3 Electrical characteristics

10V < VCC < 36V; -40°C < TJ < 125°C; unless otherwise specified

Table 3. Power section

Symbol Parameter Test conditions Min Typ Max Unit

V

R

V

demag

I

Supply voltage 10 36 V

CC

I

= 0.5A; TJ = 25°C

OUT

= 0.5A; TJ = 85°C

On state resistance

ON

I

OUT

= 0.5A; TJ = 125°C

I

OUT

All channels OFF

Supply current

S

Output voltage at turn-off

On state; V

= 125°C)

(T

J

= 0.5A; L

I

OUT

= 30V; I

IN

LOAD

= 0V

OUT

>= 1mH VCC-65 VCC-55 VCC-45

0.2

0.32

0.4

1

6

Ω

Ω

Ω

mA

mA

V

Table 4. Switching ( V

= 24V)

CC

Symbol Parameter Test conditions Min Typ Max Unit

I

= 0.5A, Resistive Load Input rise

OUT

t

d(ON)

t

t

d(OFF)

t

(di/dt)

(di/dt)

Turn-on delay time of
Output current

Rise time of Output

r

current

Turn-off delay time of
Output current

Fall time of Output

f

current

Turn-on current slope

on

Turn-off current slope

off

time < 0.1µs,

= 25°C

T

J

= 125°C

T

J

I

= 0.5A, Resistive Load Input rise

OUT

time < 0.1µs,

= 25°C

T

J

= 125°C

T

J

I

= 0.5A, Resistive Load Input rise

OUT

time < 0.1µs,

= 25°C

T

J

= 125°C

T

J

= 0.5A, Resistive Load Input rise

I

OUT

time < 0.1µs,

= 25°C

T

J

T

= 125°C

J

I

= 0.5A,

OUT

I

= I

LIM

= 0.5A,

= I

LIM

, TJ = 25°C

, TJ = 25°C

OUT

I

OUT

I

OUT

30 40

60

50 100

115

20 30

40

81520µs

0.5
2

2
4

µs
µs

µs
µs

µs
µs

µs

Α/µs
Α/µs

Α/µs
Α/µs

5/15

Electrical characteristics VN330SP-E

Table 5. Logical input

Symbol Parameter Test conditions Min Typ Max Unit

V

V

V

I(HYST)

I

I

LGND

V

1. The input voltage is internally clamped at 32V minimum, however, it is possible to connect the input pins to an higher
voltage via an external resistor that is calculated not to exceed 10mA.

Input low level voltage 2 V

IL

Input high level voltage

IH

(1)

3.5 V

Input hysteresis voltage 0.5 V

= 0 to 30V 600

(1)

V

IN

V

CC

= 25°C

T

J

I

= 1mA

IN

= -1mA

I

IN

= V

= GND = DIAG = 24V;

INn

32 36

-0.7

Input current

IN

Output current in ground
disconnection

Input clamp voltage

ICL

µΑ

25 mA

V
V

Table 6. Protection and diagnostic

Symbol Parameter Test conditions Min. Typ. Max. Unit

(1)

V

DIAG

V

SCL

V

USD

V

I

LIM

I

OVPK

I

DIAGH

I

LOAD

t

SC

T

TSD

T

1. Status determination > 100µs after the switching edge.

Status voltage output low

(1)

Status clamp voltage

Undervoltage shut down 5 8 V

Low state output voltage

OL

DC Short circuit current

Peak Short circuit current

Leakage on DIAG pin in
high state

Output leakage current

Delay time of current
limiter

Thermal shutdown
temperature

Thermal reset

R

temperature

= 5mA ( Fault condition )

I

DIAG

I

= 1mA

DIAG

= -1mA

I

DIAG

= VIL; R

V

IN

V

= 24V; R

CC

= 24V; VIN = 30; R

V

CC

V

= 24V

DIAG

= 10 to 36V; VIN = V

V

CC

LOAD

LOAD

< 10mΩ

< 10mΩ

LOAD

IL

< 10mΩ

1V

32 36

-0.7

V
V

1.5 V

0.7 2.5 A

4A

100 µΑ

50 µΑ

100 µs

150 170 °C

135 155 °C

Note: If INPUT pin is floating the corrisponding channel will automatically switch OFF. If GND pin is

disconnected, the channel will switch OFF provided V

6/15

not exceed 36V.

CC

VN330SP-E Test circuits

4 Test circuits

Figure 4. Avalance energy test circuit

Figure 5. Peak short circuit test diagram

7/15

Switching time waveforms and truth table VN330SP-E

5 Switching time waveforms and truth table

Table 7. Truth table

INPUTn OUTPUTn Diagnostic

Normal operation

Overtemperature

Undervoltage

Shorted load

( Current limitation )

Figure 6. Switching waveforms

L

H

L

H

L

H

L

H

L

H

L
L

L
L

L

H

H
H

H

L

H
H

H
H

8/15

VN330SP-E Switching time waveforms and truth table

Figure 7. Switching parameter test conditions

Figure 8. Driving circuit

9/15

Package mechanical data VN330SP-E

6 Package mechanical data

In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect . The category of
second level interconnect is marked on the package and on the inner box label, in compliance
with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also
marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are
available at: www.st.com

10/15

VN330SP-E Package mechanical data

Table 8. PowerSO-10 Mechanical data

Dim

Min Typ Max Min Typ Max

A 3.35 3.65 0.132 0.144

A1 0.00 0.10 0.000 0.004

B 0.40 0.60 0.016 0.024

c 0.23 0.32 0.009 0.012

D 9.40 9.60 0.370 0.378

D1 7.40 7.60 0.291 0.300

E 9.30 9.50 0.366 0.374

E1 7.20 7.40 0.283 0.291

E2 7.20 7.60 0.283 0.300

E3 6.10 6.35 0.240 0.250

E4 5.90 6.10 0.232 0.240

e 1.27 0.050

F 1.25 1.35 0.049 0.053

H 13.80 14.40 0.543 0.567

h 0.50 0.002

L 1.20 1.80 0.047 0.071

q 1.70 0.067

a 0° 8°

Mm Inch

Figure 9. Package dimension

11/15

Package mechanical data VN330SP-E

Figure 10. PowerSO-10TM Suggested Pad and Tube Shipment (No Suffix)

Figure 11. Tape and Reel Shipment (Suffix “TR“)

12/15

VN330SP-E Order code

7 Order code

Table 9. Order code

Part number Package Packaging

VN330SP-E

VN330SPTR-E

PowerSO-10

PowerSO-10

TM

TM

Tube

Tape and reel

13/15

Revision history VN330SP-E

8 Revision history

Table 10. Revision history

Date Revision Changes

6-Sep-2005 1 Initial release

31-Oct-2006 2 Typo in Electrical characteristics temperature conditions updated on page 5

27-Mar-2007 3 Document reformatted, typo in Note 1 on page 6

14/15

VN330SP-E

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2007 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

www.st.com

15/15