Datasheet UCC1800, UCC1801, UCC1802, UCC1803, UCC1804 Datasheet (UNITRODE)

...

Download

Page 1

查询UCC180000D供应商

Low-Power BiCMOS Current-Mode PWM

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

FEATURES

µA Typical Starting Supply Current

• 100

µA Typical Operating Supply

• 500

Current

• Operation to 1MHz

• Internal Soft Start

• Internal Fault Soft Start

DESCRIPTION

The UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count.

These devices have the same pin configuration as the UC1842/3/4/5 family, and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input.

The UCC1800/1/2/3/4/5 family offers a variety of package options, tem-

• Internal Leading-Edge Blanking of the Current Sense Signal

• 1 Amp Totem-Pole Output

perature range options, choice of maximum duty cycle, and choice of critical voltage levels. Lower reference parts such as the UCC1803 and UCC1805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC1802 and UCC1804

• 70ns Typical Response from Current-Sense to Gate Drive Output

• 1.5% Tolerance Voltage Reference

• Same Pinout as UC3842 and

make these ideal choices for use in off-line power supplies. The UCC180x series is specified for operation from –55

the UCC280x series is specified for operation from –40 the UCC380x series is specified for operation from 0

Cto+85oC, and

C to +70oC.

UC3842A

Part Number Maximum Duty Cycle Reference Voltage Turn-On Threshold Turn-Off Threshold

UCCx800 100% 5V 7.2V 6.9V UCCx801 50% 5V 9.4V 7.4V UCCx802 100% 5V 12.5V 8.3V UCCx803 100% 4V 4.1V 3.6V UCCx804 50% 5V 12.5V 8.3V UCCx805 50% 4V 4.1V 3.6V

C to +125oC,

BLOCK DIAGRAM

03/99

UDG92009-3

Page 2

ABSOLUTE MAXIMUM RATINGS (Note 1)

VCCVoltage (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.0V

VCCCurrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.0mA

OUT Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1.0A

OUT Energy (Capacitive Load) . . . . . . . . . . . . . . . . . . . 20.0µJ

Analog Inputs (FB, CS). . . . . . . . . . . . . . . . . . . . –0.3V to 6.3V

Power Dissipation at TA< +25°C (N or J Package) . . . . . 1.0W

Power Dissipation at TA< +25°C (D Package). . . . . . . . 0.65W

Storage Temperature Range. . . . . . . . . . . . . –65°C to +150°C

Lead Temperature (Soldering, 10 Seconds) . . . . . . . . +300°C

Note 1: All voltages are with respect to GND.All currents are

positive into the specified terminal. Consult Unitrode databook for information regarding thermal specifications and limitations of packages.

Note 2: In normal operation V

is powered through a current

limiting resistor.Absolute maximum of 12V applies when V that I

is driven from a low impedance source such

does not exceed 30mA.

TEMPERATURE AND PACKAGE SELECTION

Temperature Range Available Packages

UCC1800 –55°C to +125°C J UCC2800 –40°C to +85°C N, D, PW UCC3800 0°C to +70°C N, D, PW

CONNECTION DIAGRAMS

TSSOP-8 (Top View) PW Package

COMP

DIL-8, SOIC-8 (Top View) J or N, D Package

COMP

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

REF

VCC

OUT

GND

REF

VCC

OUT

GND

ORDERING INFORMATION

UCC

PACKAGE PRODUCT OPTION TEMPERATURE RANGE

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for –55°C ≤ T

≤ +125°C for

UCC180x; –40°C ≤ TA≤ +85°C for UCC280x; 0°C ≤ TA≤ +70°C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1µF capacitor from VCCto GND; 0.1µF capacitor from V

PARAMETER TEST CONDITIONS UCC180X

to GND. TA=TJ.

REF

UCC380X UNITS

UCC280X

MIN TYP MAX MIN TYP MAX

Reference Section

Output Voltage T

=+25°C, I=0.2mA, UCCx800/1/2/4 4.925 5.00 5.075 4.925 5.00 5.075 V

=+25°C, I=0.2mA, UCCx803/5 3.94 4.00 4.06 3.94 4.00 4.06

Load Regulation 0.2mA<I<5mA 10 30 10 25 mV Total Variation UCCx800/1/2/4 (Note 7) 4.88 5.00 5.10 4.88 5.00 5.10 V

UCCx803/5 (Note 7) 3.90 4.00 4.08 3.90 4.00 4.08 V Output Noise Voltage 10Hz ≤ f ≤ 10kHz, T Long Term Stability T

=+125°C, 1000 Hours (Note 9) 5 5 mV

=+25°C (Note 9) 130 130 µV

Output Short Circuit –5 –35 –5 –35 mA

Oscillator Section

Oscillator Frequency UCCx800/1/2/4 (Note 4) 40 46 52 40 46 52 kHz

UCCx803/5 (Note 4) 26 31 36 26 31 36 kHz Temperature Stability (Note 9) 2.5 2.5 % Amplitude peak-to-peak 2.25 2.40 2.55 2.25 2.40 2.55 V Oscillator Peak Voltage 2.45 2.45 V

Page 3

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

ELECTRICAL CHARACTERISTICS

PARAMETER TEST CONDITIONS UCC180X

Error Amplifier Section

Input Voltage COMP=2.5V; UCCx800/1/2/4 2.44 2.50 2.56 2.44 2.50 2.56 V

COMP=2.0V; UCCx803/5 1.95 2.0 2.05 1.95 2.0 2.05 Input Bias Current

Open Loop Voltage Gain 60 80 60 80 dB COMP Sink Current FB=2.7V, COMP=1.1V 0.3 3.5 0.4 2.5 mA COMP Source Current FB=1.8V, COMP=REF–1.2V –0.2 –0.5 –0.8 –0.2 –0.5 –0.8 mA Gain Bandwidth Product (Note 9) 2 2 MHz

PWM Section

Maximum Duty Cycle UCCx800/2/3 97 99 100 97 99 100 %

UCCx801/4/5 48 49 50 48 49 50 Minimum Duty Cycle COMP=0V 0 0 % Current Sense Section Gain (Note 5) 1.10 1.65 1.80 1.10 1.65 1.80 V/V Maximum Input Signal COMP=5V (Note 6) 0.9 1.0 1.1 0.9 1.0 1.1 V Input Bias Current CS Blank Time 50 100 150 50 100 150 ns Over-Current Threshold 1.42 1.55 1.68 1.42 1.55 1.68 V COMP to CS Offset CS=0V 0.45 0.90 1.35 0.45 0.90 1.35 V

Output Section

OUT Low Level I=20mA, all parts 0.1 0.4 0.1 0.4 V

I=200mA, all parts 0.35 0.90 0.35 0.90 V

I=50mA, VCC=5V, UCCx803/5 0.15 0.40 0.15 0.40 V

I=20mA, VCC=0V, all parts 0.7 1.2 0.7 1.2 V OUT High V

(VCC-OUT)

Rise Time C Fall Time C

Undervoltage Lockout Section

Start Threshold (Note 8) UCCx800 6.6 7.2 7.8 6.6 7.2 7.8 V

Stop Threshold (Note 8) UCCx1800 6.3 6.9 7.5 6.3 6.9 7.5 V

Start to Stop Hysteresis UCCx800 0.12 0.3 0.48 0.12 0.3 0.48 V

SAT

I=–20mA, all parts 0.15 0.40 0.15 0.40 V

I=–200mA, all parts 1.0 1.9 1.0 1.9 V

I=–50mA,VCC=5V, UCCx803/5 0.4 0.9 0.4 0.9 V

UCCx801 8.6 9.4 10.2 8.6 9.4 10.2 V

UCCx802/4 11.5 12.5 13.5 11.5 12.5 13.5 V

UCCx803/5 3.7 4.1 4.5 3.7 4.1 4.5 V

UCCx1801 6.8 7.4 8.0 6.8 7.4 8.0 V

UCCx802/4 7.6 8.3 9.0 7.6 8.3 9.0 V

UCCx803/5 3.2 3.6 4.0 3.2 3.6 4.0 V

UCCx801 1.6 2 2.4 1.6 2 2.4 V

UCCx802/4 3.5 4.2 5.1 3.5 4.2 5.1 V

UCCx803/5 0.2 0.5 0.8 0.2 0.5 0.8 V

Unless otherwise stated, these specifications apply for –55°C ≤ TA≤ +125°C for

to GND. TA=TJ.

REF

UCC280X

UCC380X UNITS

–11–11µA

–200 200 –200 200 nA

=1nF 41 70 41 70 ns

=1nF 44 75 44 75 ns

Page 4

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

ELECTRICAL CHARACTERISTICS

PARAMETER TEST CONDITIONS UCC180X

Soft Start Section

COMP Rise Time FB=1.8V, Rise from 0.5V to REF–1V 4 10 4 10 ms

Overall Section

Start-up Current V Operating Supply Current FB=0V, CS=0V 0.5 1.0 0.5 1.0 mA VCC Internal Zener Voltage I VCC Internal Zener Voltage Minus

Start Threshold Voltage

Note 3: Adjust VCC above the start threshold before setting at 10V. Note 4: Oscillator frequency for the UCCx800, UCCx802 and UCCx803 is the output frequency.

Oscillator frequency for the UCCx801, UCCx804 and UCCx805 is twice the output frequency.

Note 5: Gain is defined by: Note 6: Parameter measured at trip point of latch with Pin 2 at 0V.

Note 7: Total Variation includes temperature stability and load regulation. Note 8: Start Threshold, Stop Threshold and Zener Shunt Thresholds track one another. Note 9: Guaranteed by design. Not 100% tested in production.

UCCx802/4 0.5 1.0 0.5 1.0 V

∆

COMP

=≤≤

∆

Unless otherwise stated, these specifications apply for –55°C ≤ TA≤ +125°C for

to GND. TA=TJ.

REF

UCC280X

< Start Threshold 0.1 0.2 0.1 0.2 mA

=10mA (Note 8) 12 13.5 15 12 13.5 15 V

008.

UCC380X UNITS

PIN DESCRIPTIONS

COMP: COMP is the output of the error amplifier and the

input of the PWM comparator. Unlike other devices, the error amplifier in the UCC3800

family is a true, low output-impedance, 2MHz operational amplifier. As such, the COMP terminal can both source and sink current. However, the error amplifier is internally current limited, so that you can command zero duty cycle by externally forcing COMP to GND.

The UCC3800 family features built-in full cycle Soft Start. Soft Start is implemented as a clamp on the maximum COMP voltage.

CS: CS is the input to the current sense comparators. The UCC3800 family has two different current sense comparators: the PWM comparator and an over-current comparator.

The UCC3800 family contains digital current sense filtering, which disconnects the CS terminal from the current sense comparator during the 100ns interval immediately following the rising edge of the OUT pin. This digital filtering, also called leading-edge blanking, means that in most applications, no analog filtering (RC filter) is required on CS. Compared to an external RC filter technique, the leading-edge blanking provides a smaller

effective CS to OUT propagation delay. Note, however, that the minimum non-zero On-Time of the OUT signal is directly affected by the leading-edge-blanking and the CS to OUT propagation delay.

The over-current comparator is only intended for fault sensing, and exceeding the over-current threshold will cause a soft start cycle.

FB: FB is the inverting input of the error amplifier. For best stability, keep FB lead length as short as possible and FB stray capacitance as small as possible.

GND: GND is reference ground and power ground for all functions on this part.

OUT: OUT is the output of a high-current power driver capable of driving the gate of a power MOSFET with peak currents exceeding ± 750mA. OUT is actively held low when V

is below the UVLO threshold.

The high-current power driver consists of FET output devices, which can switch all of the way to GND and all of thewaytoV

. The output stage also provides a very

low impedance to overshoot and undershoot. This means that in many cases, external schottky clamp diodes are not required.

Page 5

PIN DESCRIPTIONS (cont.)

RC: RC is the oscillator timing pin. For fixed frequency

operation, set timing capacitor charging current by connecting a resistor from REF to RC. Set frequency by connecting a timing capacitor from RC to GND. For best performance, keep the timing capacitor lead to GND as short and direct as possible. If possible, use separate ground traces for the timing capacitor and all other functions.

The frequency of oscillation can be estimated with the following equations:

UCCx800/1/2/4:

UCCx803, UCCx805:

where frequency is in Hz, resistance is in ohms, and capacitance is in farads. The recommended range of timing resistors is between 10k and 200k and timing capacitor is 100pF to 1000pF. Never use a timing resistor less than 10k.

To prevent noise problems, bypass VCC to GND with a ceramic capacitor as close to the VCC pin as possible. An electrolytic capacitor may also be used in addition to the ceramic capacitor.

REF: REF is the voltage reference for the error amplifier and also for many other functions on the IC. REF is also

15.

• =

10.

•

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

used as the logic power supply for high speed switching logic on the IC.

When V threshold, REF is pulled to ground through a 5k ohm resistor. This means that REF can be used as a logic output indicating power system status. It is important for reference stability that REF is bypassed to GND with a ceramic capacitor as close to the pin as possible. An electrolytic capacitor may also be used in addition to the ceramic capacitor. A minimum of 0.1µF ceramic is required. Additional REF bypassing is required for external loads greater than 2.5mA on the reference.

To prevent noise problems with high speed switching transients, bypass REF to ground with a ceramic capacitor very close to the IC package.

VCC: V In normal operation V limiting resistor. Although quiescent V low, total supply current will be higher, depending on OUT current. Total V V

current and the average OUT current. Knowing the

operating frequency and the MOSFET gate charge (Qg), average OUT current can be calculated from:

IQF

is greater than 1V and less than the UVLO

is the power input connection for this device.

is powered through a current

current is very

current is the sum of quiescent

=×

OUT

The UCC3800/1/2/3/4/5 oscillator generates a sawtooth waveform on RC.The rise time is set by the time constant of R

and CT. The fall time is set by CT and an internal transis-

Ω

tor on-resistance of approximately 125 time, the output is off and the maximum duty cycle is reduced below 50% or 100% depending on the part number. Larger timing capacitors increase the discharge time and reduce the maximum duty cycle and frequency.

. During the fall

Figure 1. Oscillator.

Figure 2. Error amplifier gain/phase response.

Page 6

4.00

3.98

3.96

3.94

3.92

REF

3.90

V (V)

3.88

3.86

3.84

3.82 4 4.2 4.4 4.6 4.8

Figure 3. UCC1803/5 V

REF

5.2 5.4 5.6 5.8 6

V (V)

vs. VCC;I

LOAD

= 0.5mA.

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

1000

100pF

100

200pF

Oscillator Freq. (kHz)

10 100 1000

Figure 4. UCC1800/1/2/4 oscillator frequency vs. R and CT.

330pF

1nF

R(k)

1000

100

Oscillator Freq. (kHz)

100pF

200pF 330pF

1nF

10 100 1000

R(k)

Figure 5. UCC1803/5 oscillator frequency vs. RTand C

49.5

48.5

47.5

Maximum Duty Cycle (%)

C = 200pF

C = 330pF

C = 100pF

100

99.5 99

98.5 98

97.5 97

96.5

Maximum Duty Cycle (%)

95.5 95

10 100 1000

Oscillator Frequency (kHz)

C = 200pF

C = 330pF

C = 100pF

Figure 6. UCC1800/2/3 maximum duty cycle vs. oscillator frequency.

I (mA)

V = 10V, 1nF

V = 8V, 1nF

V = 10V, No Load

V = 8V, No Load

46.5 10 100 1000

Oscillator Frequency (kHz)

Figure 7. UCC1801/4/5 maximum duty cycle vs. oscillator frequency.

0 100 200 300 400 500 600 700 800 900 1000

Oscillator Frequency (kHz)

Figure 8. UCC1800 ICCvs. oscillator frequency.

Page 7

UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5

I (mA)

0 100 200 300 400 500 600 700 800 900 1000

Oscillator Frequency (kHz)

V = 10V, 1nF

V = 8V, 1nF

V = 10V, No Load

V = 8V, No Load

Figure 8. UCC1805 ICCvs. oscillator frequency.

1.1

1.0

0.9

500 450 400 350 300 250 200

Dead Time (ns)

150 100

100 200 300 400 500 600 700 800 900 1000

C (pF)

UCC1803/5

UCC1800/1/2/4

Figure 9. Dead time vs. CT,RT= 100k.

0.8

Slope = 1.8mV/ C

0.7

COMP to CS Offset (Volts)

0.6

-55-50 -25 0 25 50 75 100 125

Temperature (°C)

Figure 10. COMP to CS offset vs. temperature, CS = 0V.

Page 8

IMPORTANT NOTICE

T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICA TIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERST OOD TO BE FULLY AT THE CUSTOMER’S RISK.

In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.