Page 1
Through-beam ultrasonic barrier UBE4000-30GM-SA2-V15
Technical data
General specifications
Sensing range 0 ... 4000 mm , distance emitter-receiver 500 mm ... 4000 mm
Through-beam mode Single path ultrasonic switch
Reference target receiver
Transducer frequency 85 kHz
Indicators/operating means
Model Number
UBE4000-30GM-SA2-V15
Features
• Reliable detection of transparent
materials
• High switching frequency
• Adjustable sensitivity
• Adjustable switch-on delay
•Small angle of divergence
•Protective functions
• Emitter and receiver included in
the delivery package
LED green alignment aid
LED yellow switching state
Electrical specifications
Operating voltage U
No-load supply current I
B
0
Output
Output type 2 switch outputs PNP, normally open/closed
Rated operating current I
Voltage drop U
Switch-on delay t
d
Switching frequency f ≤ 15 Hz
e
on
Ambient conditions
Ambient temperature 0 ... 60 °C (32 ... 140 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type Connector M12 x 1 , 5-pin
Degree of protection IP65
Material
Housing nickel plated brass; plastic components: PBT
Mass 160 g each sensor
Compliance with standards and
directives
Standard conformity
Standards EN 60947-5-2:2007 + A1:2012
Approvals and certificates
UL approval cULus Listed, General Purpose
CSA approval cCSAus Listed, General Purpose
CCC approval CCC approval / marking not required for products rated ≤36 V
OFF: no ultrasonic signal
flashing: uncertain area
ON: positive reception
18 ... 30 V DC , ripple 10 %
35 mA emitter
SS
25 mA receiver
(complementary)
200 mA
≤ 2.5 V
100 ... 3000 ms
IEC 60947-5-2:2007 + A1:2012
Diagrams
Characteristic response curves
90 80 70 60 50 40 30
0.0
0.5
1.0
1.5
2.0
Distance [m]
2.5 3.0 3.5 4.0 4.5 5.0 5.5
α
Angle [degrees]
Dimensions
Dimensions:
20
10
0
-10
-20
Emitter: Receiver:
ø40
25
LED green
internal distance regulator
Threaded pipe M30x1.5
90
22
Dual-LED
green/yellow
Plug connectorPlug connector
Potentiometer
ON delay
Release date: 2016-04-18 10:43 Date of issue: 2016-04-18 120344_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
1
Page 2
Through-beam ultrasonic barrier UBE4000-30GM-SA2-V15
Electrical Connection
Standard symbol/Connection:
(version A2, pnp)
Receiver:
U
Emitter:
U
Core colours in accordance with EN 60947-5-2.
Pinout
Additional Information
Alignment
1
(BN)
(WH)
2
(BK)
4
5
n.c.
3
(BU)
1
(BN)
2
(WH)
4
(BK)
5
n.c.
3
(BU)
2
+U
B
N.C.N.O.
-U
B
+U
B
10k
-U
B
1
5
4
α
s
3
Wire colors in accordance with EN 60947-5-2
1 BN
2 WH
3 BU
4 BK
5 GY
(brown)
(white)
(blue)
(black)
(gray)
Accessories
FP100
Remote potentiometer
BF 30
Mounting flange, 30 mm
BF 5-30
Universal mounting bracket for cylindrical sensors with a diameter of 5 ... 30 mm
V1-G-2M-PVC
Female cordset, M12, 4-pin, PVC cable
Description of the sensor functions
Remote potentiometer
The distance range of the through-beam ultrasonic barrier can be adjusted with the
potentiometer integrated in the emitter, or via a remote potentiometer connected to
the emitter.
The remote potentiometer simplifies the adjustment of the distance range if the sensors are installed in an inaccessible location. A 10 kΩ/0.3 W potentiometer serves
as the remote potentiometer. The connection is realised using the plug connector
pins 2 and 4 of the emitter (see: Electrical Connection).
Release date: 2016-04-18 10:43 Date of issue: 2016-04-18 120344_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
2
Page 3
Through-beam ultrasonic barrier UBE4000-30GM-SA2-V15
The following distance ranges can be set using the remote potentiometer:
Adjustment of the internal distance regulator
Minimum switching point 0 m ... 2 m
Maximum switching point 2 m ... 4 m
When operating without a remote potentiometer, the plug connector pins 2 and 4 must be bridged.
Adjustment
Turning the potentiometer on the emitter to the left (counterclockwise) causes a reduction of the transmission power. Thus, the
through-beam ultrasonic barrier becomes more sensitive.
Note: If no remote potentiometer is connected and the connector pins 2 and 4 are not bridged, the emitter always operates at
maximum transmission power. The through-beam ultrasonic barrier then has the lowest sensitivity. Turning the transmitter side
potentiometer won’t have an effect, then.
Alignment
When adjusting the emitter and receiver, take care to align them as precisely as possible.
Angular tolerance: α < ± 2°
maximum offset: s < ± 5 mm
A through-beam ultrasonic barrier consists of a single emitter and a single receiver.
Caution
Mount or replace emitter and receiver only in pairs. Both devices are optimally matched to each other by the manufacturer.
Distance range adjustable via remote potentiometer
Release date: 2016-04-18 10:43 Date of issue: 2016-04-18 120344_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
3
Loading...