Datasheet TDA4565 Specification

Download

Page 1

INTEGRATED CIRCUITS

DATA SH EET

TDA4565

Colour transient improvement circuit

Product speciﬁcation File under Integrated Circuits, IC02

November 1989

Page 2

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

GENERAL DESCRIPTION

The TDA4565 is a monolithic integrated circuit for colour transient improvement (CTI) and luminance delay line in gyrator technique in colour television receivers.

Features

• Colour transient improvement for colour difference signals (R-Y) and (B-Y) with transient detecting-, storage- and switching stages resulting in high transients of colour difference output signals

• A luminance signal path (Y) which substitutes the conventional Y-delay coil with an integrated Y-delay line

• Switchable delay time from 730 ns to 1000 ns in steps of 90 ns and additional fine adjustment of 50 ns

• Two Y output signals; one of 180 ns less delay

QUICK REFERENCE DATA

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply voltage (pin 10) V Supply current (pin 10) I Y-signal delay at pin 12 S1 open; R

14-18

= 1.2 kΩ;

(note 1)

= 0 to 2.5 V t

15-18

= 3.5 to 5.5 V t

15-18

= 6.5 to 8.5 V t

15-18

= 9.5 to 12 V t

15-18

Y-signal attenuation 0.5 MHz α (R-Y) and (B-Y) signal

attenuation α output transient time t

17-12 17-12 17-12 17-12

10.8 12 13.2 V

− 35 50 mA

670 730 790 ns 760 820 880 ns 850 910 970 ns 940 1000 1060 ns 0 6.5 8.0 dB

−10 +1dB

− 100 200 ns

Note

1. Delay time is proportional to resistor R

also influences the bandwidth; a value of 1.2 kΩ results in a bandwidth of 5 MHz (typ.).

14-18

PACKAGE OUTLINE

18-lead DIL; plastic (SOT102); SOT102-1; 1996 November 27.

November 1989 2

Page 3

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

November 1989 3

Fig.1 Block diagram.

Page 4

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

November 1989 4

Fig.2 Internal pin circuit diagram.

Page 5

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)

PARAMETER SYMBOL MIN. MAX. UNIT

Supply voltage range (pin 10) V Voltage ranges to pin 18 (ground)

at pins 1, 2, 12 and 15 V at pin 11 V at pin 17 V

Voltage ranges

at pin 7 to pin 6 V at pin 8 to pin 9 V

Currents

at pins 6, 9 I at pins 7, 8, 11 and 12 I

Total power dissipation

= 150 °C; T

= 70 °C) P

amb

Storage temperature range T Operating ambient temperature range T

= V

10-18

n-18 11-18 17-18

7-6 8-9

6, 9 7, 8, 11, 12

tot stg amb

0 13.2 V

0V 0(V

−3V) V

07V

05V 05V

−10 +10 mA internally limited

− 1.1 W

−25 +150 °C

0 +70 °C

THERMAL RESISTANCE

From junction to ambient (in free air) R

Note

1. Pins 3, 4, 5, 6, 9, 13 and 14 DC potential not published.

th j-a

= 70 K/W

November 1989 5

Page 6

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

CHARACTERISTICS

= V

Supply (pin 10) Supply voltage V

Supply current l

Colour difference paths

(R-Y) input voltage (75% colour bar signal)

(peak-to-peak value) V (B-Y) input voltage (75% colour bar signal)

(peak-to-peak value) V Input resistance

(R-Y) R

(B-Y) R Internal bias voltage

(R-Y) V

(B-Y) V Signal attenuation

(R-Y) V

(B-Y) V Output transient time note 1 t Output resistance

(B-Y) R

(R-Y) R DC output voltage

(B-Y) V

(R-Y) V Output current note 2

source I

sink −I

10-18

= 12 V; T

= 25 °C; measured in application circuit Fig.3; unless otherwise speciﬁed

amb

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

1(p-p)

2(p-p)

1-18 2-18

1-18 1-18

8/V1 7/V2

7-18 8-18

7-18 8−18

7, 8

10.8 12 13.2 V

− 35 50 mA

− 1.05 1.5 V

− 1.33 1.9 V

8 1216kΩ 8 1216kΩ

3.8 4.3 4.8 V

−10 +1dB

− 100 200 ns

− 100 −Ω

3.8 4.3 4.8 V

0.4 −−mA

1.0 −−mA

November 1989 6

Page 7

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Y-signal path

Y-input voltage

(composite signal) capacitive coupling

(peak-to-peak value) V Internal bias voltage during clamping V

17(p-p) 17-18

Input current

during picture content I

during sync. pulse −I

Y-signal delay at pin 12 S1 open;

= 1.2 kΩ;

(notes 3 and 4) at V at V at V at V

= 0 to 2.5 V t

15-18

= 3.5 to 5.5 V t

15-18

= 6.5 to 8.5 V t

15-18

= 9.5 to 12 V t

15-18

17-18 17-18 17-18 17-18

Fine adjustment of Y-signal

delay for all 4 steps S1 closed t

17-12

Signal delay between pin 11

and pin 12 S1 open t

11-12

Dependency of delay time

on temperature − 0.001 − K

on supply voltage −−0.03 − V

Input switching current −I

∆

17 12–

--------------------------t

.Tj∆

17 12–

∆

17 12–

----------------------------t

.Vp∆

17 12–

Y-signal attenuation f = 0.5 MHz

pin 11 from pin 17 V11/V pin 12 from pin 17 V

12/V17

Frequency response at

3 MHz referred to 0.5 MHz note 5 pin 11 0 − 3.0 dB

3MHz)(

----------------------------------------- -

0.5 MHz )(

− 1 1.4 V

1.3 1.5 1.7 V

− 812µA

− 100 150 µA

670 730 790 ns 760 820 880 ns 850 910 970 ns 940 1000 1060 ns

30 50 70 ns

160 180 200 ns

−1

− 15 25 µA

5.0 6.5 8.0 dB

pin 12 0 − 3.0 dB

3MHz)(

----------------------------------------- -

0.5 MHz )(

November 1989 7

Page 8

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Frequency response at

5 MHz referred to 0.5 MHz note 5 pin 11 −3.0 − 2.0 dB

V115MHz)(

----------------------------------------- V

0.5 MHz )(

pin 12 −3.0 − 2.0 dB

V125 MHz(

----------------------------------------- -

0.5 MHz )(

DC output voltage

pin 11 V pin 12 V

11−18 12−18

1.8 2.3 2.6 V

9.8 10.3 10.8 V

Output current note 2

source I sink −I

11, 12

−−0.4 mA

−−1.0 mA

Notes to the characteristics

1. Output signal transient time measured with C

6−18

= C

= 220 pF without resistor (see Fig.3).

9-18

2. Output current measured with emitter follower with constant current source of 0.6 mA.

3. R

4. Delay time is proportional to resistor R

5. Frequency response measured with V

influences the bandwidth; a value of 1.2 kΩ results in a bandwidth of 5 MHz (typ.).

14-18

. Devices with suffix “A” require the value of the resistor to be 1.15 kΩ;

14-18

a 27 kΩ resistor connected in parallel with R

15-18

= 1.2 kΩ.

14-18

= 9.5 V and switch S1 open.

November 1989 8

Page 9

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

APPLICATION INFORMATION

(1) Residual carrier reduced to 20 mV peak-to-peak (R = 1 kΩ, C = 100 pF). (2) Switching sequence for delay times shown in Table 1. (3) R

= 1.2 kΩ for TDA4565

14-18

= 1.15 kΩ for TDA4565A (27 kΩ resistor connected in parallel to 1.2 kΩ).

14-18

Fig.3 Application diagram and test circuit.

Table 1 Switching sequence for delay times.

CONNECTION

(2)

VOLTAGE AT PIN 15 DELAY TIME (ns)

(a) (b) (c)

0 0 0 0 to 2.5 V 730 0 0 X 3.5 to 5.5 V 820 0 X X 6.5 to 8.5 V 910 X X X 9.5 to 12 V 1000

Note

1. When switch (S1) is closed the delay time is increased by 50 ns.

2. Where: X = connection closed; 0 = connection open.

November 1989 9

(1)

Page 10

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

PACKAGE OUTLINE

DIP18: plastic dual in-line package; 18 leads (300 mil)

seating plane

pin 1 index

SOT102-1

w M

(e )

0 5 10 mm

scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

UNIT

max.

inches

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

OUTLINE VERSION

SOT102-1

min.

max.

IEC JEDEC EIAJ

1.40

1.14

0.055

0.044

0.53

0.38

0.021

0.015

1.40

1.14

0.055

0.044

REFERENCES

cD E e M

0.32

0.23

0.013

0.009

21.8

21.4

0.86

0.84

November 1989 10

(1) (1)

6.48

6.20

0.26

0.24

3.9

8.25

3.4

7.80

0.15

0.32

0.13

0.31

EUROPEAN

PROJECTION

9.5

8.3

0.37

0.33

0.2542.54 7.62

0.010.10 0.30

ISSUE DATE

93-10-14 95-01-23

max.

0.854.7 0.51 3.7

0.0330.19 0.020 0.15

(1)

Page 11

Philips Semiconductors Product speciﬁcation

Colour transient improvement circuit TDA4565

SOLDERING Introduction

There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used.

This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our

“IC Package Databook”

Soldering by dipping or by wave

The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds.

The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (T be necessary immediately after soldering to keep the temperature within the permissible limit.

(order code 9398 652 90011).

). If the printed-circuit board has been pre-heated, forced cooling may

stg max

Repairing soldered joints

Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds.

DEFINITIONS

Data sheet status

Objective speciﬁcation This data sheet contains target or goal speciﬁcations for product development. Preliminary speciﬁcation This data sheet contains preliminary data; supplementary data may be published later. Product speciﬁcation This data sheet contains ﬁnal product speciﬁcations.

Limiting values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the speciﬁcation is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the speciﬁcation.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.

November 1989 11