Datasheet T435T-600FP Datasheet (ST)

Page 1
T435T-600FP
4 A Snubberless™ Triac
Features
High static and dynamic commutation
Package is RoHS (2002/95/EC) compliant
I
= 35 mA
Applications
Specially designed for power tool applications, it can also be used to drive loads like motor speed controller, and kitchen equipment such as electro valves, light dimmers and similar.
Description
Available in through-hole package, the Triac T435T-600FP is suitable for general purpose AC switching.
Being a fully insulated package, the T435T-600FP provides insulation rated at 1500 V rms.
A2
G
A1
TO-220FPAB T435T-600FP
G
A2
A1
TM: Snubberless is a trademark of STMicroelectronics
June 2010 Doc ID 17632 Rev 2 1/8
www.st.com
8
Page 2
Characteristics T435T-600FP

1 Characteristics

Table 1. Absolute maximum ratings (limiting values)

Symbol Parameter Value Unit
I
T(RMS)
I
TSM
²
I
dI/dt
V
DSM/VRSM
I
GM
P
G(AV)
T
stg
T
Table 2. Electrical characteristics, Snubberless (3 quadrants)
On-state rms current (full sine wave) Tc = 105 °C 4 A
Non repetitive surge peak on-state current (full cycle sine wave, TJ initial = 25 °C)
²
tI
t Value for fusing tp = 10 ms 6 A²s
Critical rate of rise of on-state current I
= 2 x IGT, tr 100 ns
G
Non repetitive surge peak off-state voiltage tp = 10 ms Tj = 25 °C
F = 60 Hz t = 16.7 ms 32
F = 50 Hz t = 20 ms 30
F = 120 Hz Tj = 125 °C 50 A/µs
V
DRM/VRRM
Peak gate current tp = 20 µs Tj = 125 °C 4 A
Average gate power dissipation Tj = 125 °C 1 W
Storage junction temperature range Operating junction temperature range
j
(T
= 25 °C, unless otherwise specified)
j
-40 to +150
-40 to +125
+ 100
Symbol Test conditions Quadrant Value Unit
(1)
I
GT
V
GT
V
GD
I
H
VD = 12 V RL = 30 Ω I - II - III MAX 35 mA
VD = 12 V RL = 30 Ω I - II - III MAX 1.3 V
VD = V
(2)
IT = 100 mA MAX 35 mA
= 3.3 kΩ I - II - III MIN 0.2 V
DRM RL
I - III MAX 50
I
L
dV/dt
(dI/dt)c
1. Minimum IGT is guaranteed at 5% of IGT max.
2. For both polarities of A2 pin referenced to A1 pin

Table 3. Static electrical characteristics

IG = 1.2 x I
(2)
VD = 67% V
(2)
Without snubber, Tj = 125 °C MIN 5.3 A/ms
GT
, gate open, Tj = 125 °C MIN 750 V/µs
DRM
II MAX 80
A
V
°C
mA
Symbol Test conditions Value Unit
(1)
I
V
TM
(1)
V
TO
(1)
R
D
I
DRM
I
RRM
1. For both polarities of A2 pin referenced to A1 pin
= 5.7 A, tp = 380 µs Tj = 25 °C MAX 1.6 V
TM
Threshold voltage Tj = 125 °C MAX 0.9 V
Dynamic resistance Tj = 125 °C MAX 100 mΩ
V
DRM
= V
RRM
Tj = 25 °C
MAX
T
= 125 °C 1 mA
j
A
2/8 Doc ID 17632 Rev 2
Page 3
T435T-600FP Characteristics

Table 4. Thermal resistances

Symbol Parameter Value Unit
R
th(j-c)
R
th(j-a)
Figure 1. Maximum power dissipation versus
P(W)
5
4
3
2
1
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Figure 3. On-state current (rms) versus
Junction to case (ac) 4.3
Junction to ambient 60
Figure 2. On-state current (rms) versus case
rms on-state current (full cycle)
180°
I
(A)
T(RMS)
I
T(RMS)
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0 25 50 75 100 125
temperature (full cycle)
(A)
TC(°C)
Figure 4. Relative variation of thermal
ambient temperature
impedance versus pulse duration
α=180°
(free air convection)
I
(A)
T(RMS)
2.5
2.0
α=180°
1.0E+00
K=[Zth/Rth]
Z
th(j-c)
°C/W
1.5
1.0
0.5
0.0
0 25 50 75 100 125
T
(°C)
amb
Figure 5. Relative variation of gate trigger
current, and gate trigger voltage versus junction temperature
IGT,VGT[Tj]/IGT,VGT[Tj=25 °C]
3.0
IGTQ3
2.5
2.0
IGTQ1-Q2
1.5
1.0
VGTQ1-Q2-Q3
0.5
0.0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130
typical values
Tj(°C)
Z
th(j-a)
1.0E-01
1.0E-02
1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03
tP(s)
Figure 6. Relative variation of holding
current and latching current versus junction temperature
IH,IL[Tj]/IH,IL[Tj=25 °C]
3.0
2.5
2.0
1.5
1.0
0.5
0.0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130
typical values
Tj(°C)
Doc ID 17632 Rev 2 3/8
Page 4
Characteristics T435T-600FP
(A)
Figure 7. Surge peak on-state current versus
number of cycles
I
(A)
TSM
35
30
25
20
15
10
5
0
Repetitive
=105 °C
T
C
1 10 100 1000
Non repetitive
initial=25 °C
T
j
Number of cycles
t=20ms
One cycle
Figure 9. On-state characteristics
(maximum values)
I
TM
100
Tj=25 °C
Tj=125 °C
10
Tjmax :
V
= 0.9 V
1
012345 67
VTM(V)
to
R
d
= 100 mΩ
Figure 8. Non-repetitive surge peak on-state
current for a sinusoidal
I
(A), I²t (A²s)
TSM
1000
100
10
1
0.01 0.10 1.00 10.00
dI/dt limitation: 50 A/µs
pulse t < 10 ms, and corresponding value of I t
p
tP(ms)
Tjinitial=25 °C
I
TSM
2
I²t
Figure 10. Relative variation of critical rate of
decrease of main current (di/dt)c versus junction temperature
(dI/dt)c[Tj]/(dI/dt)c[Tj=125 °C]
8
7
6
5
4
3
2
1
0
25 50 75 100 125
Tj(°C)
Figure 11. Relative variation of critical rate of
decrease of main current (di/dt)c versus reapplied (dV/dt)c
(dI/dt)c[(dV/dt)c] / Speci fied (dI/ dt)
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0.1 1.0 10.0 100.0
c
typical values
(dV/dt)c(V/µs)
Figure 12. Relative variation of static dV/dt
immunity versus junction temperature
dV/dt [Tj]/dV/dt[Tj=125 °C]
8
7
6
5
4
3
2
1
0
25 50 75 100 125
Tj(°C)
VD=VR=400 V
4/8 Doc ID 17632 Rev 2
Page 5
T435T-600FP Ordering information scheme

2 Ordering information scheme

Figure 13. Ordering information scheme

T 4 35 T - 600 FP
Triac series
Current
4 = 4 A
Sensitivity
35 = 35 mA
Specific application
Voltage
600 = 600 V
Package
FP = Full pack
Doc ID 17632 Rev 2 5/8
Page 6
Package information T435T-600FP

3 Package information

Epoxy meets UL94, V0
Lead-free packages
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK specifications, grade definitions and product status are available at: www.st.com ECOPACK

Table 5. TO-220FPAB dimensions

®
packages, depending on their level of environmental compliance. ECOPACK®
®
is an ST trademark.
.
Dimensions
Ref.
Millimeters Inches
Min. Max. Min. Max.
A 4.4 4.6 0.173 0.181
A
H
B
B 2.5 2.7 0.098 0.106
D 2.5 2.75 0.098 0.108
E 0.45 0.70 0.018 0.027
Dia
L6
L2
L3
L5
F1
L4
F2
F
G1
G
D
L7
E
F 0.75 1 0.030 0.039
F1 1.15 1.70 0.045 0.067
F2 1.15 1.70 0.045 0.067
G 4.95 5.20 0.195 0.205
G1 2.4 2.7 0.094 0.106
H 10 10.4 0.393 0.409
L2 16 Typ. 0.63 Typ.
L3 28.6 30.6 1.126 1.205
L4 9.8 10.6 0.386 0.417
L5 2.9 3.6 0.114 0.142
L6 15.9 16.4 0.626 0.646
L7 9.00 9.30 0.354 0.366
6/8 Doc ID 17632 Rev 2
Dia. 3.00 3.20 0.118 0.126
Page 7
T435T-600FP Ordering information

4 Ordering information

Table 6. Ordering information

Order code Marking Package Weight Base qty Packing mode
T435T-600FP T435T-600 TO-220FPAB 2.0 g 50 Tube

5 Revision history

Table 7. Document revision history

Date Revision Changes
09-Nov-2007 1 Initial release.
14-Jun-2010 2 Updated ECOPACK statement.
Doc ID 17632 Rev 2 7/8
Page 8
T435T-600FP
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
8/8 Doc ID 17632 Rev 2
Loading...