Page 1
STD1NC60
N-CH A NNEL 60 0V - 7Ω - 1.4A - DPAK/IPAK
PowerMesh™II MOSFET
TYPE V
STD1NC60 600 V < 8
■ TYPICAL R
■ EXTREMELY HIGH dv /d t C APABILITY
■ 100% AVALANCHE TESTED
■ NEW HIGH VOLTAGE BENCHMARK
■ GATE CHARGE MINIMIZED
DS
DSS
(on) = 7 Ω
R
DS(on)
I
D
Ω
1.4 A
DESCRIPTION
The PowerMESH
generation of MESH OVERLAY
™II is the evolution of the first
™. The layout re-
finements introduced greatly improve the Ron*area
figure of merit while keeping the device at the lea ding edge for what concerns swithing speed, gate
charge and ruggedness.
APPLICATIONS
■ HIGH CURRENT, HIGH SPEED SWITCHING
■ SWITH MODE POWER SUPPLI ES ( SMPS)
■ DC-AC CONVERTERS FOR WELDING
EQUIPMENT AND UNINTERRUPTIBLE
POWER SUPPLIES AND MOTOR DRIVER
3
2
1
1
IPAK
TO-251
INTERNAL SCHEMATIC DIAGRAM
DPAK
TO-252
3
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
(1)
j
Drain-source Voltage (VGS = 0)
Drain-gate Voltage (RGS = 20 kΩ)
Gate- source Voltage ±30 V
Drain Current (continuos) at TC = 25°C
Drain Current (continuos) at TC = 100°C
Drain Current (pulsed) 5.6 A
Total Dissipation at TC = 25°C
Derating Factor 0.28 W/°C
Storage Temperature –65 to 150 °C
Max. Operating Junction Temperature 150 °C
(1)ISD ≤1.4A, di/ dt ≤100A/µs, VDD ≤ V
600 V
600 V
1.4 A
0.9 A
35 W
, Tj ≤ T
(BR)DSS
JMAX
V
DS
V
DGR
V
GS
I
D
I
D
I
DM
P
TOT
dv/dt Peak Diode Recovery voltage slope 3.5 V/ns
T
stg
T
(•)Pu l se width limited by safe operati ng area
.
1/9December 2000
Page 2
STD1NC60
THERMA L D ATA
Rthj-case Thermal Resistance Junction-case Max 3.6 °C/W
Rthj-amb Thermal Resistance Junction-ambient Max 100 °C/W
Rthj-sink Thermal Resistance case-sink Typ 1.5 °C/W
T
AVALANCHE CHARACTERISTICS
Symbol Parameter Max Value Unit
I
AR
E
AS
ELECTRICAL CHARACTERISTICS (TCASE = 25 °C UNLESS OTHERWISE SPECIFIED)
OFF
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
(BR)DSS
I
DSS
I
GSS
Maximum Lead Temperature For Soldering Purpose 275 °C
l
Avalanche Current, Repetitive or Not-Repetitive
(pulse width limited by T
max)
j
Single Pulse Avalanche Energy
(starting T
= 25 °C, ID = IAR, VDD = 50 V)
j
Drain-source
Breakdown Voltage
Zero Gate Voltage
Drain Current (V
GS
= 0)
Gate-body Leakage
Current (V
DS
= 0)
1.4 A
70 mJ
ID = 250 µA, VGS = 0 600
V
= Max Rating
DS
V
= Max Rating, TC = 125 °C
DS
V
= ±30V ±100 nA
GS
1µA
10 µA
V
ON
(1)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
V
GS(th)
R
DS(on)
Gate Threshold Voltage
Static Drain-source On
= VGS, ID = 250µA
DS
VGS = 10V, ID = 0.7 A
234V
78
Resistance
I
D(on)
On State Drain Current VDS > I
D(on)
x R
DS(on)max,
1.4 A
VGS=10V
DYNAMIC
Symbol Parameter Test Conditions Min. Typ. Max. Unit
(1) Forward Transconductance VDS > I
g
fs
C
iss
C
oss
C
rss
Input Capacitance
Output Capacitance 26 pF
Reverse Transfer
Capacitance
ID= 0.7A
V
DS
D(on)
x R
DS(on)max,
= 25V, f = 1 MHz, VGS = 0
1.25 S
160 pF
3.8 pF
Ω
2/9
Page 3
STD1NC60
ELECTRICAL CHARACTERISTICS (CONTINUED)
SWITCHING ON
Symbol Parameter Test Conditions Min. Typ. Max. Unit
t
d(on)
Turn-on Delay Time VDD = 300V, ID = 0.7 A
RG= 4.7Ω VGS = 10V
t
r
Q
g
Q
gs
Q
gd
Rise Time 8 ns
Total Gate Charge
Gate-Source Charge 2.8 nC
Gate-Drain Charge 2.8 nC
(see test circuit, Figure 3)
V
= 480V, ID = 1.4 A,
DD
V
= 10V
GS
SWITCHING OFF
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
t
r(Voff)
t
t
Off-voltage Rise Time
f
c
Fall Time 9 ns
Cross-over Time 34 ns
= 480V, ID = 1.4 A,
DD
RG=4.7Ω, V
GS
= 10V
(see test circuit, Figure 5)
SOURCE DRAIN DIODE
Symbol Parameter Test Conditions Min. Typ. Max. Unit
I
SD
I
SDM
VSD (1)
t
rr
Q
rr
I
RRM
Note: 1. Pulsed: Pu l se duration = 300 µs, duty cycle 1. 5 %.
2. Pulse width li mited by safe operating area .
Source-drain Current 1.4 A
(2)
Source-drain Current (pulsed) 5.6 A
Forward On Voltage
Reverse Recovery Time
Reverse Recovery Charge 950 nC
ISD = 1.4 A, VGS = 0
I
= 1.4 A, di/dt = 100A/µs,
SD
VDD = 100V, Tj = 150°C
(see test circuit, Figure 5)
Reverse Recovery Current 3.8 A
8ns
8.5 11.5 nC
25 ns
1.6 V
500 ns
Thermal Imp e danceSafe Operating Area
3/9
Page 4
STD1NC60
Output Characteristics Transfer Characteristics
Transconductance
Gate Charge vs Gate-source Voltage
Static Drain-source On Resistance
Capacitance Variations
4/9
Page 5
Source-drain Diode Forward Characteristics
STD1NC60
Normalized On Resistance vs Temperatur eNormalized Gate Thereshold Voltage vs Temp.
5/9
Page 6
STD1NC60
Fig. 2: Unclamped Inductive WaveformFig. 1: Unclamped Inductive Load Test Circuit
Fig. 3: Switching Times Test Circuit For
Resistive Load
Fig. 5: Test Circuit For Inductive Load Switching
And Diode Recovery Times
Fig. 4: Gate Charge test Circuit
6/9
Page 7
TO-251 (IPAK) MECHANICAL DAT A
STD1NC60
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
mm inch
A 2.2 2.4 0.086 0.094
A1 0.9 1.1 0.035 0.043
A3 0.7 1.3 0.027 0.051
B 0.64 0.9 0.025 0.031
B2 5.2 5.4 0.204 0.212
B3 0.85 0.033
B5 0.3 0.012
B6 0.95 0.037
C 0.45 0.6 0.017 0.023
C2 0.48 0.6 0.019 0.023
D 6 6.2 0.236 0.244
E 6.4 6.6 0.252 0.260
G 4.4 4.6 0.173 0.181
H 15.9 16.3 0.626 0.641
L 9 9.4 0.354 0.370
L1 0.8 1.2 0.031 0.047
L2 0.8 1 0.031 0.039
H
A
C2
L2
E
B2
= =
= =
D
B3
2
1 3
L1
A1
L
B6
C
A3
B
B5
G
= =
0068771-E
7/9
Page 8
STD1NC60
TO-252 (DPAK) MECHANICAL DATA
DIM.
A 2.20 2.40 0.087 0.094
A1 0.90 1.10 0.035 0.043
A2 0.03 0.23 0.001 0.009
B 0.64 0.90 0.025 0.035
B2 5.20 5.40 0.204 0.213
C 0.45 0.60 0.018 0.024
C2 0.48 0.60 0.019 0.024
D 6.00 6.20 0.236 0.244
E 6.40 6.60 0.252 0.260
G 4.40 4.60 0.173 0.181
H 9.35 10.10 0.368 0.398
L2 0.8 0.031
L4 0.60 1.00 0.024 0.039
V2 0
MIN. TYP. MAX. MIN. TYP. MAX.
o
mm inch
o
8
o
0
o
0
8/9
P032P_B
Page 9
STD1NC60
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such informa tion n or for an y infring ement of patent s or other rig hts of third part ies which may resu lt from its use . No l i cen se i s
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical compo nents in life support devices or systems without express written approval of STMicroelectronics.
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco -
The ST logo is a trademark of STMicroelectronics
© 2000 STMicroelectronics – Printed in Italy – All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
9/9
Loading...