The SC3610 is a frequency and clock display driver used for
displaying FM/AM radio frequency or a 12 hour alarm clock. By using
CMOS technology, it consumes very low power in clock display
mode.
FEATURES
* FM input with pre-scalar for radio frequency up to 150 MHz
* AM input for radio frequency up to 30 MHz
* 3 common, 13 segment, 1/3 bias LCD display drivers which
supports 4 digits LCD display
* On chip oscillator for external 32.768kHz crystal
* 10.7 MHz / 70 kHz I.F. frequency offset for FM signal and 455kHz
I.F. frequency offset for AM signal
* Internal real time clock in 12 hour display mode
* Selectable clock or frequency display
* 1.8V to 3.3V supply voltage
21RST ISU
22TESTCLKISDFor testing use only with internal pull-down
23TESTISDWhen high, the chip will enter test mode
24AL-ON/OFFISUAlarm function on or off in toggle mode. Internal pull up input
25AL-DISPISUWhen pressed, will display the alarm time. Internal pull up input
26MIN-SETISU
27HR-SETISUHoursetting for time and alarm(together with AL-DISP). Internal pull up.
28NC--No connection
29CLKFREQ-SELISD
30V
31AL-SIG
32AL-OUTO4Alarm output at 1kHz with 0.2 sec on and 0.2 sec off, push-pull output.
33IF70kISDSelect IF offset in FM mode. H:70kHz, L:10.7kHz
34NC--No connection
35RANGEISUFor frequency counting mode only, Range = H or L, gate time = 0.1S
36AM/FM-SELISUAM/FM mode selection. High for AM and low for FM, internal pull-up.
37AV
38AM
39AV
40FM
Note:IOscillator Input PadOOscillator Output Pad
Symbol I/O Description
LCD Supply voltage. Connects a 0.1 µF capacitor between this pin and
LCD
SS
DD
IN
SS
IN
ISUSchmitt trigger input pad with pull-upOD10Open Drain with 10mA output driving
ISDSchmitt trigger input pad with pull-downO4Push-pull output pad with 4mA driving
O
V
SS
Active low power-on reset with pull-up resistor of approx.750kΩ
Minute setting for time and alarm(together w ith AL-DISP). Internal pull
up.
Clock or frequency display mode. Internal pull-down input. When low,
clock will be displayed. When high, radio frequency will be displayed.
--Ground pin
Open drain alarm signal output, active low.
OD10
--Analog Supply voltage
--AM signal input, 0.3V peak to peak, 500kHz to 30MHz.
The FM and AM local oscillator output generated from the external RF receiver enters a high gain input
comparator through the FM
dynamic pre-scalar. Depending on the state of the AM/FM-SEL pin, the FM and AM signal will be selected and
enters the IF frequency offset block. Depending on the FM/AM selection, 10.7MHz/70kHz or 455kHz I.F.
frequency will be subtracted or added from the input signal.
LCD Display Range:
Mode Range Display range (on LCD) Step Resolution
FMH
AMH
Note:1 When counter frequency overflow, MSB will not be displayed.
IF Offset for different application:
IF70K AMFM-
00+10.7MHzDisplay FM input frequency 10.7MHz
01+455kHzDisplay AM input frequency 455kHz
10-70 kHz*Display FM input frequency +70kHz
11+455 kHzDisplay AM input frequency 455kHz
* Suitable to use with Silan SC1088
and the AMINpins respectively. The FM signal then routes through a divide-by-10
IN
L
L
SEL
11.00 MHz to 99.99 MHz
11.00 MHz to 149.9 kHz
500 kHz to 9999 kHz
0.5 MHz to 29.99 MHz
IF Offset Operation
10kHz
100kHz
1kHz
10kHz
SC3610
1kHz
10kHz
100kHz
1kHz
2. CLOCK FUNCTION:
1) The clock will be advanced in the following flow:
PM 12:00 → PM 11:59 → AM 12:00 → 11:59
2) The [:] sign is the second indicator and will blink at a rate of 2Hz
3) TIME SETTING:
--Pressing the keys combination of [TIME SET] [HR SET] or [TIME SET] [MIN SET] will enter the time
setting mode.
--One digit will be incremented afte r enter in g the alarm sett in g mode. Keep pressing the keys
combination for more than 0.5 seconds will make the digit to be advanced at a rate of 2Hz.
4) ALARM TIME SETTING:
-- Pressing the keys combination of [AL DISP] [HR SET] or [AL DISP] [MIN SET] will enter the alarm time
setting mode. The [AL] indicator will turn on and the [:] sign will stop blinking.
-- One digit will be incremented after entering the alarm setting mode. Keep pressing the keys combination