Datasheet SA10, SA100, SA100C, SA100A, SA100CA Datasheet (BYTES)

SA5.0 SA180CATHRU

500 WATT PEAK POWER TRANSIENT VOLTAGE SUPPRESSORS

VOLTAGE RANGE

5.0 to 180 Volts

FEATURES

* 500 Watts Surge Capability at 1ms

* Excellent clamping capability
* Low zener impedance

* Fast response time: Typically less than

1.0ps from 0 volt to BV min.
* Typical I less than 1 A above 10VR µ

* High temperature soldering guaranteed:
260 C / 10 seconds / .375"(9.5mm) lead
length, 5lbs.(2.3kg) tension

500 Watts Peak Power

3.0 Watts Steady State

DO-15

.140(3.6)
.104(2.6)
DIA.

MECHANICAL DATA

* Case: Molded plastic
* Epoxy: UL 94V-0 rate flame retardant
* Lead: Axial leads, solderable per MIL-STD-202,
method 208 guranteed
* Polarity: Color band denotes cathode end
* Mounting position: Any

*

Weight: 0.40 grams

.034(.9)
.028(.7)

DIA.

Dimensions in inches and (millimeters)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating 25 C ambient temperature uniess otherwies specified.
Single phase half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.

1.0(25.4)
MIN.

.300(7.6)
.230(5.8)

1.0(25.4)
MIN.

RATINGS SYMBOL VALUE UNITS

Peak Power Dissipation at T =25 C, T =1ms(NOTE 1) P Minimum 500 WattsA P PK
Steady State Power Dissipation at T =75 CL
Lead Length .375"(9.5mm) (NOTE 2)

Peak Forward Surge Current at 8.3ms Single Half Sine-Wave

superimposed on rated load (JEDEC method) (NOTE 3)

Operating and Storage Temperature Range T , T -55 to +175 CJ STG

NOTES:

1. Non-repetitive current pulse per Fig. 3 and derated above T =25 C per Fig. 2.

2. Mounted on Copper Pad area of 1.6" X 1.6" (40mm X 40mm) per Fig.5.

3. 8.3ms single half sine-wave, duty cycle = 4 pulses per minute maximum.

A

P 3.0 WattsD

I 70 AmpsFSM

DEVICES FOR BIPOLAR APPLICATIONS

1. For Bidirectional use C or CA Suffix for types SA5.0 thru SA180.

2. Electrical characteristics apply in both directions.

134

RATING AND CHARACTERISTIC CURVES (SA5.0 THRU SA180CA)

FIG.1-PEAK PULSE POWER DERATING CURVE

100

10

1.0

P , PEAK PULSE POWER, KWPPM

0.1

0.1 s 1.0 s 10 s 100 s 1.0ms 10ms µ µ µ µ

td, PULSE WIDTH, sec.

FIG.3-PULSE WAVE FORM

150

T =25 C

tf=10 s

µ

Peak Value
I

PPM

100

50

I , PEAK PULSE CURRENT, %PPM

td

0

0 1.0 2.0 3.0 4.0

A

Pulse Width (td) is defined
as the point where the Peak
Current Deacys to 50% of Ipp

Half Value-IPPM

2

10/1000 sec Waveform

µ

as Defined by R.E.A.

e-kt

t, TIME, ms

Non-Repetitive
Pulse Waveform
Shown in Fig. 3
T =25 CA

FIG.2-PULSE DERATING CURVE

100

75

PP PP

50

25

PEAK PULSE POWER(P ) OR CURRENT(I )

DERATING IN PERCENTAGE

0

0 25 50 75 100 125 150 175

T , AMBIENT TEMPERATURE ( C)A

FIG.4-TYPICAL JUNCTION CAPACITANCE

10,000

5,000

2,000

1,000

500

200

100

C , CAPACITANCE, pFJ

50

20

10

1.0 2.0 5.0 10 20 50 100 200

Measured at
Stand-Off
Voltage(V )MW

V(BR), BREAKDOWN VOLTAGE, VOLTS

T =25 C
f=1.0MHz
Vsig=50mVp-p

J

Measued at
Zero Bias

FIG.5-STEADY STATE POWER DERATING CURVE

1.00

0.75

L=.375"(9.5mm)

0.50

40mm x 40mm x 1mm
Copper Heat Sink

0.25

Pm( ), STEADY STATE POWER DISSIPATION, WATTSAV

(1.6" x 1.6" x .040")

0

0 25 50 75 100 125 150 175 200

T , LEAD TEMPERATURE ( C)L

135

FIG.6-MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT, UNIDIRECTIONAL

100

T =T max

80

60

40

20

FSM

I , PEAK FORWARD SURGE

CURRENT, AMPERES

10

1 5 10 20 50 100

NUMBER OF CYCLES AT 60Hz

J J

8.3ms Single Half Sine-wave
JEDEC Method

500 Watt Axial Lead TVS

UNI REVERSE BREAKDOWN BREAKDOWN TEST MAXIMUM PEAK REVERSE
DIRECTIONAL STAND-OFF VOLTAGE VOLTAGE CURRENT CLAMPING PULSE LEAKAGE
PART VOLTAGE VBR (V) VRB (V) IT VOLTAGE CURRENT @ VRWM
NUMBER VRWM (V) MIN. @IT MAX. @IT (mA) @Ipp Vc (V) Ipp (A) IR( A)

SA5.0 5.00 6.40 7.30 10 9.6 53.1 600
SA5.0A 5.00 6.40 7.00 10 9.2 55.4 600
SA6.0 6.00 6.67 8.15 10 11.4 44.7 600
SA6.0A 6.00 6.67 7.37 10 10.3 49.5 600

SA6.5 6.50 7.22 8.82 10 12.3 41.5 400

SA6.5A 6.50 7.22 7.98 10 11.2 45.5 400
SA7.0 7.00 7.78 9.51 10 13.3 38.3 150

SA7.0A 7.00 7.78 8.60 10 12.0 42.5 150
SA7.5 7.50 8.33 10.20 1 14.3 35.7 50

SA7.5A 7.50 8.33 9.21 1 12.9 39.5 50
SA8.0 8.00 8.89 10.90 1 15.0 34.0 25

SA8.0A 8.00 8.89 9.83 1 13.6 37.5 25
SA8.5 8.50 9.44 11.50 1 15.9 32.1 10

SA8.5A 8.50 9.44 10.40 1 14.4 35.4 10
SA9.0 9.00 10.00 12.20 1 16.9 30.2 5

SA9.0A 9.00 10.00 11.10 1 15.4 33.1 5

SA10 10.00 11.10 13.60 1 18.8 27.1 3

SA10A 10.00 11.10 12.30 1 17.0 30.0 3
SA11 11.00 12.20 14.90 1 20.1 25.4 3
SA11A 11.00 12.20 13.50 1 18.2 28.0 3

SA12 12.00 13.30 16.30 1 22.0 23.2 3

SA12A 12.00 13.30 14.70 1 19.9 25.6 3
SA13 13.00 14.40 17.60 1 23.8 21.4 3
SA13A 13.00 14.40 15.90 1 21.5 23.7 3

SA14 14.00 15.60 19.10 1 25.8 19.8 3

SA14A 14.00 15.60 17.20 1 23.2 22.0 3

SA15 15.00 16.70 20.40 1 26.9 19.0 3

SA15A 15.00 16.70 18.50 1 24.4 20.9 3
SA16 16.00 17.80 21.80 1 28.8 17.7 3

SA16A 16.00 17.80 19.70 1 26.0 19.6 3
SA17 17.00 18.90 23.10 1 30.5 16.7 3

SA17A 17.00 18.90 20.90 1 27.6 18.5 3

SA18 18.00 20.00 24.40 1 32.2 15.8 3

SA18A 18.00 20.00 22.10 1 29.2 17.5 3
SA20 20.00 22.20 27.10 1 35.8 14.2 3

SA20A 20.00 22.20 24.50 1 32.4 15.7 3
SA22 22.00 24.40 29.80 1 39.4 12.9 3

SA22A 22.00 24.40 26.90 1 35.5 14.4 3
SA24 24.00 26.70 32.60 1 43.0 11.9 3
SA24A 24.00 26.70 29.50 1 38.9 13.1 3

SA26 26.00 28.90 35.30 1 46.6 10.9 3
SA26A 26.00 28.90 31.90 1 42.1 12.1 3
SA28 28.00 31.10 38.00 1 50.1 10.2 3

SA28A 28.00 31.10 34.40 1 45.4 11.2 3

SA30 30.00 33.30 40.70 1 53.5 9.5 3

SA30A 30.00 33.30 36.80 1 48.4 10.5 3
SA33 33.00 36.70 44.90 1 59.0 8.6 3
SA33A 33.00 36.70 40.60 1 53.3 9.6 3

SA36 36.00 40.00 48.90 1 64.3 7.9 3

SA36A 36.00 40.00 44.20 1 58.1 8.8 3
SA40 40.00 44.40 54.30 1 71.4 7.1 3

SA40A 40.00 44.40 49.10 1 64.5 7.9 3

µ

140

500 Watt Axial Lead TVS

UNI REVERSE BREAKDOWN BREAKDOWN TEST MAXIMUM PEAK REVERSE
DIRECTIONAL STAND-OFF VOLTAGE VOLTAGE CURRENT CLAMPING PULSE LEAKAGE
PART VOLTAGE VBR (V) VRB (V) IT VOLTAGE CURRENT @ VRWM
NUMBER VRWM (V) MIN. @IT MAX. @IT (mA) @Ipp Vc (V) Ipp (A) IR( A)

SA43 43.00 47.80 58.40 1 76.7 6.6 3
SA43A 43.00 47.80 52.80 1 69.4 7.3 3
SA45 45.00 50.00 61.10 1 80.3 6.4 3
SA45A 45.00 50.00 55.30 1 72.7 7.0 3

SA48 48.00 53.30 65.20 1 85.5 6.0 3
SA48A 48.00 53.30 58.90 1 77.4 6.6 3
SA51 51.00 56.70 69.30 1 91.1 5.6 3

SA51A 51.00 56.70 62.70 1 82.4 6.2 3
SA54 54.00 60.00 73.30 1 96.3 5.3 3

SA54A 54.00 60.00 66.30 1 87.1 5.9 3
SA58 58.00 64.40 78.70 1 103.0 5.0 3

SA58A 58.00 64.40 71.20 1 93.6 5.4 3
SA60 60.00 66.70 81.50 1 107.0 4.8 3

SA60A 60.00 66.70 73.70 1 96.8 5.3 3
SA64 64.00 71.10 86.90 1 114.0 4.5 3

SA64A 64.00 71.10 78.60 1 103.0 5.0 3

SA70 70.00 77.80 95.10 1 125.0 4.1 3
SA70A 70.00 77.80 86.00 1 113.0 4.5 3
SA75 75.00 83.30 102.00 1 134.0 3.8 3

SA75A 75.00 83.30 92.10 1 121.0 4.2 3
SA78 78.00 86.70 106.00 1 139.0 3.7 3

SA78A 78.00 86.70 95.80 1 126.0 4.0 3
SA85 85.00 94.40 115.00 1 151.0 3.4 3
SA85A 85.00 94.40 104.00 1 137.0 3.7 3

SA90 90.00 100.00 122.00 1 160.0 3.2 3
SA90A 90.00 100.00 111.00 1 146.0 3.5 3
SA100 100.00 111.00 136.00 1 179.0 2.8 3

SA100A 100.00 111.00 123.00 1 162.0 3.1 3
SA110 110.00 122.00 149.00 1 196.0 2.6 3

SA110A 110.00 122.00 135.00 1 177.0 2.9 3
SA120 120.00 133.00 163.00 1 214.0 2.4 3

SA120A 120.00 133.00 147.00 1 193.0 2.6 3

SA130 130.00 144.00 176.00 1 230.0 2.2 3

SA130A 130.00 144.00 159.00 1 209.0 2.4 3
SA150 150.00 167.00 204.00 1 268.0 1.9 3
SA150A 150.00 167.00 185.00 1 243.0 2.1 3

SA160 160.00 178.00 218.00 1 287.0 1.7 3

SA160A 160.00 178.00 197.00 1 259.0 2.0 3
SA170 170.00 189.00 231.00 1 304.0 1.7 3
SA170A 170.00 189.00 209.00 1 275.0 1.9 3

SA180 180.00 200.00 244.00 1 320.0 1.6 3

SA180A 180.00 200.00 233.00 1 289.0 1.7 3

µ

141