Datasheet OMR117AHVNM, OMR117AHVST, OMR117AHVSR, OMR117AHVNH Datasheet (OMNIREL)

100K Rad T olerant Three T erminal, Precision Adjustable Positive Voltage
Regulator In Hermetic Packages
100 kRAD RADIATION TOLERANT 1.5 AMP POSITIVE ADJUSTABLE VOLTAGE REGULATOR
OMR117AHVNHOMR117AHVNMOMR117AHVSTOMR117AHVSR
FEATURES
• Adjustable Output Voltage
• Built In Thermal Overload Protection
• Short Circuit Current Limiting
• Available In Four Hermetic Package Styles
• Maximum Output Voltage Tolerance Is Guaranteed to +
1%
• Radiation Tolerant up to 150 K Rad (Si)
• Available Hi-Rel Screened, Class B and Class S, MIL-STD-883
DESCRIPTION
These three terminal positive regulators are supplied in high density hermetically sealed packages and available Hi-Rel screened. All protective features are designed into the circuit, including thermal shutdown, current-limiting, and safe-area control. With heat sinking, these devices can deliver up to 1.5 amps of output current. These units also feature output voltages that can be fixed from 1.2 volts to 57 volts using external resistors. These devices are ideally suited for Space applications where small size, high reliability, and radiation tolerance is required. The high level of Radiation Tolerance of these devices makes them a desirable choice for LEO and many MEO and GEO communication satellites. Radiation testing is performed on a single wafer by wafer basis. Random die samples per wafer are selected, packaged and radiation tested to qualify each individual semiconductor wafer-by-wafer.
ABSOLUTE MAXIMUM RATINGST
c
@ 25°C
Power Dissipation:TO-205 . ......................................... 1.1 W
TO-257/SMD/ D2Pac ................ ............................ 20 W
Input - Output Voltage Differential . .................................. 60 V
Operating Junction Temperature Range . ....................- 55°C to + 150°C
Storage Temperature Range . .............................- 65°C to + 150°C
Lead Temperature (Soldering 10 seconds) . .......................... 300°C
Thermal Resistance, Junction to Case:
TO-205 ...................................................... 17°C/W
TO-257(Isolated), D2Pac (Isolated)................................... 4.2°C/W
TO-257 (Non-Isolated) and SMD-1 .. . ....... . .................... 3.5°C/W
Maximum Output Current: TO-205. ....... ............................ .5 A
Case-All Others . . .................. ............................. 1.5A
Recommended Operating Conditions:
Output Voltage Range . . . ..................................1.2 to 57 VDC
Input Voltage Range . .................................4.25 to 61.25 VDC
Radiation Tolerant - Total Dose . ......................... ......100 K Rad (Si)
Surface Mount P ac kage Soldering Temperature . ......................... .250°C
Please see mechanical
outlines herein
0 04 R2 Supersedes 9 12 R1
OMR117 4/4/2000 11:46 AM Page 1
OMR117AHVSR, OMR117AHVST, OMR117AHVNM, OMR117AHVNH
Parameter Symbol Test Conditions Min. Max. Unit
Reference Voltage V
REF
V
DIFF
= 3.0V, TA= 25°C 1.238 1.262
(Note 4) V
DIFF
= 3.3V 1.225 1.270 V
V
DIFF
= 40V 1.225 1.270
V
DIFF
= 60V 1.225 1.270
Line Regulation R
LINE
3.0V ≤ V
DIFF
40V, V
out
= V
ref
, TA= 25°C 4.5
(Note 1, 4) 3.3V ≤V
DIFF
40V, V
out
= V
ref
9mV
40V ≤ V
DIFF
60V, V
out
= V
ref
, TA= 25°C 5
40V ≤ V
DIFF
60V, V
out
= V
ref
10
Load Regulation R
LOADVDIFF
= 3.0V, 10mA ≤ IL≤ 1.5A, TA= 25°C 15
(Note 1, 4) V
DIFF
= 3.3V, 10mA ≤ IL≤ 1.5A 15 mV
V
DIFF
= 40V, 10mA ≤ IL≤ 300mA, TA= 25°C 15 V
DIFF
= 40V, 10mA ≤ IL≤ 195mA 15
V
DIFF
= 60V, 10mA ≤ IL≤ 30mA 15
Thermal Regulation V
RTH
Vin= 14.6V, IL= 1.5A 5 mV
P
d
= 20 Watts, t = 20 ms, TA= 25°C
Ripple Rejection R
N
f = 120 Hz, V
out
= V
ref
66 dB
C
Adj
= 10 µF, I
out
= 100 mA
Adjustment Pin I
Adj
V
DIFF
= 3.0V, TA= 25°C 100
Current V
DIFF
= 3.3V 100 µA
V
DIFF
= 40V 100
(Note 4) V
DIFF
= 60V 100
Adjustment Pin ∆I
AdjVDIFF
= 3.0V, 10mA ≤ IL≤ 1.5A, TA= 25°C 5
Current Change V
DIFF
= 3.3V, 10mA ≤ IL≤ 1.5A 5
V
DIFF
= 40V, 10mA ≤ IL≤ 300mA, TA= 25°C 5
V
DIFF
= 40V, 10mA ≤ IL≤ 195mA 5 µA
3.0V ≤ V
DIFF
40V, TA= 25°C 5
3.3V ≤ V
DIFF
40V 5
3.3V ≤ V
DIFF
60V 5
Minimum Load Current I
Lmin
V
DIFF
= 3.0V, V
out
= 1.4V (forced) 10
V
DIFF
= 3.3V, V
out
= 1.4V (forced) mA
V
DIFF
= 40V, V
out
= 1.4V (forced)
V
DIFF
= 60V, V
out
= 1.4V (forced)
Current Limit I
CL
V
DIFF
= 5V 1.5 3.5
(Note 2, 4) V
DIFF
= 40V, TA= 25°C 0.3 1.5 A
V
DIFF
= 60V, TA= 25°C 0.05 0.5
Notes:
1.Load and Line Regulation are measured at a constant junction temperature using a low duty cycle pulse technique. Changes in output voltage due to heating effects must be taken into account separately.
2.If not tested, shall be guaranteed to the specified limits.
3.The • denotes the specifications which apply over the full temperature range.
4.Refer to curves for typical characteristics versus Total Dose Radiation Levels.
RADIA TION TEST PROGRAM
The following chart is a summary of the test data collected on Radiation Tolerant OMR117AHV at various doses. The char t depicts the Total Radiation Dose that each device was e xposed to on a step stress irradiation basis prior to failure. Failure is defined as any electrical test that does not meet the limits of the device per the published data sheet specifications after radiation testing.
ELECTRICAL CHARACTERISTICS
-55°C ≤T
A
125°C, IL= 8mA (unless otherwise specified)
Omnirel P/N 5K 10K 20K 30K 50K 60K 70K 80K 100K 150K 200K RAD OMR117AHV Test Points XX XX
OMR117 4/4/2000 11:46 AM Page 2
Radiation Testing is performed on a single wafer by wafer basis.
Each wafer is identified and a random sample of 5 die per wafer is selected.
The die are then individually assembled in a hermetic package, data logged, electrically tested, hi-rel screened and then submitted to radiation testing.
The packaged die are submitted to Steady State Total Dose radiation per Method 1019, Condition A, at a dose rate of 50 RAD/sec biased at maximum supply voltage.
Final electrical test is performed within two hours of both Total Dose Radiation level from a Cobalt 60 source and 168 hr, 100°C annealing process. Read and record data including two non-radiated control samples.
The wafer is then qualified only if samples from wafers meet full electrical specifications after 150% of total dose rating as specified in each product data sheet.
Omnirel’s controlling specifications are as follows: For Voltage Regulators the controlling specification is MIL-PRF- 38534/MIL-STD-883. For Rectifiers/Schottky the controlling specification is MIL-PRF-19500/MIL-STD-750.
OMR117AHVSR, OMR117AHVST, OMR117AHVNM, OMR117AHVNH
OMNIREL’S RADIATION TEST PROCEDURE
Standard Class Level Screening
Per MIL-PRF-38535
Screen *Level B *Level S
Test Method Required Test Method Required
Wafer Lot Acceptance ----- ----- 5007 100% Non-destructive Bond Pull ----- ----- ----- ----­Pre-Cap Visual Inspection 2010 100% 2010 100% Temperature Cycle 1010 100% 1010 100% Constant Acceleration 2001 100% 2001 100% Visual Inspection ----- 100% ----- 100% PIND Test ----- ----- 2020 100% Serialization ----- ----- ----- 100% Pre-Burn-In Electrical Data Sheet 100% Data Sheet 100% Burn-In 1015/160 hrs. 100% 1015/240hrs. 100% Interim Electrical ----- ----- Data Sheet 100% PDA Calculations 5% Functional Lot 5% Functional Lot Final Electrical Data Sheet 100% Data Sheet 100% Fine & Gross Seal 1014 100% 1014 100% Radiographic ----- ----- 2012/Two Views 100% Conformance Inspection GR A&B Sample GR A&B Sample Final Visual Inspection 2009 Sample 2009 Sample
*Note: For “B” Level Screening add “M” to part number, for “S” Level Screening add “S” to part number. See Part Number Designator.
AVAILABLE PRODUCT SCREENING
OMR117 4/4/2000 11:46 AM Page 3
STANDARD APPLICATION
*Cinis required if regulator is located an appreciable distance from the power supply.
** C
out
is not needed for stability, however it does
improve transient response.
V
out
= 1.25 V (1 + R2/R1) + I
Ad j R2
Since I
Adj
is controlled to less than 100 µA, the error associated with this term is negligible in most applications.
OMR117AHV
V
in
Cin*
0.1 µF
V
out
C
out
**
1.0 µF
R
2
Adjust
I
Adj
R
1
240
OMR117AHVSR, OMR117AHVST, OMR117AHVNM, OMR117AHVNH
TYPICAL RADIATION CURVES
OMR117 4/4/2000 11:46 AM Page 4
MECHANICAL OUTLINES
OMR117AHVSR, OMR117AHVST, OMR117AHVNM, OMR117AHVNH
OMR117AHVNH
Non-Isolated
Pin 1 - Input Pin 2 - Adjust Pin 3 - Output (Case)
Add “H” to part number for TO-205 Pa ckage
OMR117AHVST
Isolated/Front View
Pin 1 - Adjust Pin 2 - Output Pin 3 - Input Tab - Isolated
Add “T” to part number for
TO-257 Package
OMR117AHVNM
Pin 1 - Adjust Pin 2 - Input Pin 3 - Output
Add “M” to part number for
SMD (Surface Mount Package)
.430 .410
.200 .190
.038 MAX.
.005
.120 TYP.
.537 .527
.665 .645
.420 .410
.150 .140
.750 .500
.100 TYP.
.035 .025
.045 .035
.450
.140
.415
.157
.015
.140
.140
.050
.050
.037
.375
.030 MIN.
TOP VIEW SIDE VIEW BOTTOM VIEW
.625
123
1
2
3
“T” P/N DESIGNATOR
“H” P/N DESIGNATOR
TO-257AA
TO-205AF (TO-39)
SMD-1
PART NUMBER DESIGNATOR
(Example OMR117AHVSTM)
OMR 117 AHV S T M
Omnirel Device 1% Hi-Volt Isolated Package Screening
Rad-Tolerant Type Package Style Level
Hermetic D2Pac
“R” P/N DESIGNATOR
OMR117AHVSR
Isolated
Front View
Pin 1 - Adjust Pin 2 - Output Pin 3 - Input Tab - Isolated
Add “R” to part number for
D2Pac Package
“M” P/N DESIGNATOR
OMR117 4/4/2000 11:46 AM Page 5
THANK YOU FOR YOUR INTEREST IN
OMNIREL’S PRODUCTS!
OMR117 4/4/2000 11:46 AM Page 6
205 Crawford Street, Leominster, MA 01453 USA (978) 534-5776 FAX (978) 537-4246 Visit Our Web Site at www.omnirel.com
Loading...