Datasheet MSM83C154S-xxxTS-K, MSM83C154S-xxxJS, MSM80C154STS-K, MSM80C154SJS, MSM83C154S-xxxRS Datasheet (OKI)

E2E1023-27-Y3

This version: Jan. 1998

MSM80C154S/83C154S¡ Semiconductor

¡ Semiconductor

Previous version: Nov. 1996

MSM80C154S/83C154S

CMOS 8-bit Microcontroller

GENERAL DESCRIPTION

The MSM80C154S/MSM83C154S, designed for the high speed version of the existing
MSM80C154/MSM83C154, is a higher performance 8-bit microcontroller providing low-power
consumption.
The MSM80C154S/MSM83C154S covers the functions and operating range of the existing
MSM80C154/83C154/80C51F/80C31F.
The MSM80C154S is identical to the MSM83C154S except it does not contain the internal
program memory (ROM).

FEATURES

• Operating range
Operating frequency : 0 to 3 MHz (Vcc=2.2 to 6.0 V)

0 to 12 MHz (Vcc=3.0 to 6.0 V)
0 to 24 MHz (Vcc=4.5 to 6.0 V)

Operating voltage : 2.2 to 6.0 V

Operating temperature : –40 to +85°C (Operation at +125°C conforms to

the other specification.)

• Fully static circuit

• Upward compatible with the MSM80C51F/80C31F

• On-chip program memory : 16K words x 8 bits ROM (MSM83C154S only)

• On-chip data memory : 256 words x 8 bits RAM

• External program memory address space : 64K bytes ROM (Max)

• External data memory address space : 64K bytes RAM

• I/O ports : 4 ports x 8 bits

(Port 1, 2, 3, impedance programmable) : 32

• 16-bit timer/counters : 3

• Multifunctional serial port : I/O Expansion mode

: UART mode (featuring error detection)

• 6-source 2-priority level

Interrupt and multi-level
Interrupt available by programming IP and IE registers

• Memory-mapped special function registers

• Bit addressable data memory and SFRs

• Minimum instruction cycle : 500 ns @ 24 MHz operation

• Standby functions : Power-down mode (oscillator stop)

Activated by software or hardware; providing
ports with floating or active status
The software power-down stet mode is termi­nated by interrupt signal enabling execution from
the interrupted address.

1/40

MSM80C154S/83C154S¡ Semiconductor

• Package options

40-pin plastic DIP (DIP40-P-600-2.54) :

44-pin plastic QFP (QFP44-P-910-0.80-2K) :

44-pin QFJ (QFJ44-P-S650-1.27) : (Product name: MSM80C154SJS/

44-pin TQFP (TQFP44-P-1010-0.80-K) : (Product name: MSM80C154STS-K/

(Product name: MSM80C154SRS/

MSM83C154S-xxxRS)

(Product name: MSM80C154SGS-2K/

MSM83C154S-xxxGS-2K)

MSM83C154S

MSM83C154S-xxxTS-K)

xxx: indicates the code number

-xxx

JS)

2/40

3/40

MSM80C154S/83C154S¡ Semiconductor

T2CON

PCH

CONTROL SIGNAL

SPECIAL
FUNCTION
REGISTER

ADDRESS
DECODER

PLA

IR AIR

C-ROM

TR1

TR2ACC

ALU

BR

PSW

RAMDP

R/W AMP

RAM

256 WORDS

x 8BITS

TH2

RCAP2H

RCAP2L

DPH

PCL

SP

ROM

16K WORDS x 8BITS

SENSE AMP

DPL

PCLL

PORT 2PORT 0

PCONIOCON

OSC and TIMING

PORT 1PORT 3

P2.0

P2.7

P0.0

P0.7

P1.0

P1.7

P3.0

P3.7

XTAL1

XTAL2

ALE

RESET

PSEN

EA

TH1 TL1 TH0 TL0 TMOD TCON IE IP SBUF(T) SBUF(R)

INTERRUPT

TIMER/COUNTER 0 & 1

SERIAL IO

SCON

SIGNALR/W

TIMER/

COUNTER 2

PCHL

ADDRESS DECODER

TL2

BLOCK DIAGRAM (MSM83C154S)

PIN CONFIGURATION (TOP VIEW)

MSM80C154S/83C154S¡ Semiconductor

P1.0/T2

P1.1/T2EX

P1.2
P1.3
P1.4

P1.5
P1.6
P1.7

RESET

P3.0/RXD

P3.1/TXD
P3.2/INT0
P3.3/INT1

P3.4/T0

P3.5/T1/HPDI

P3.6/WR

P3.7/RD

XTAL2
XTAL1

V

SS

10
11
12
13
14
15
16
17
18

19
20

1
2
3
4
5

6
7
8
9

40
39
38
37
36

35
34
33
32
31
30
29
28
27
26
25
24
23
22
21

V

CC

P0.0
P0.1
P0.2
P0.3

P0.4
P0.5
P0.6
P0.7

EA

ALE

PSEN

P2.7
P2.6
P2.5
P2.4
P2.3
P2.2
P2.1
P2.0

40-Pin Plastic DIP

4/40

PIN CONFIGURATION (Continued)

P1.4

P1.3

44

43

P1.2
42

P1.1
41

P1.0NCV
40

39

CC

38

P0.0

37

P0.1
36

P0.2
35

MSM80C154S/83C154S¡ Semiconductor

P0.3
34

P1.5
P1.6
P1.7

RESET

P3.0/RXD

NC

P3.1/TXD
P3.2/INT0
P3.3/INT1

P3.4/T0

P3.5/T1/HPDI

10
11

1
2
3
4
5
6
7
8
9

12

13

14

15

16

17

18

19

20

21

22

SSVSS

P3.7/RD

P3.6/WR

XTAL2

XTAL1

V

P2.0

P2.1

P2.2

P2.3

P2.4

33
32
31
30
29
28
27
26
25
24
23

P0.4
P0.5
P0.6
P0.7
EA
NC
ALE
PSEN
P2.7
P2.6
P2.5

NC : No-connection pin

44-Pin Plastic QFP

5/40

P1.4
44

P1.3
43

P1.2
42

P1.1
41

P1.0NCV
40

39

CC

38

P0.0
37

P0.1
36

P0.2
35

MSM80C154S/83C154S¡ Semiconductor

P0.3
34

P1.5
P1.6
P1.7

RESET

P3.0/RXD

NC

P3.1/TXD
P3.2/INT0
P3.3/INT1

P3.4/T0

P3.5/T1/HPDI

10
11

1
2
3
4
5
6
7
8
9

12

13

14

15

16

17

18

19

20

21

22

SSVSS

P3.7/RD

P3.6/WR

XTAL2

XTAL1

V

P2.0

P2.1

P2.2

P2.3

P2.4

33
32
31
30
29
28
27
26
25
24
23

P0.4
P0.5
P0.6
P0.7
EA
NC
ALE
PSEN
P2.7
P2.6
P2.5

NC : No-connection pin

44-Pin Plastic TQFP

6/40

PIN CONFIGURATION (Continued)

P0.5
38

P0.6
37

P0.4
39

P0.7EANC
36

35

34

ALE

33

PSEN

32

P2.7

31

P2.6

30

MSM80C154S/83C154S¡ Semiconductor

P2.5
29

P0.3
P0.2
P0.1
P0.0

V

CC

NC

P1.0/T2

P1.1/T2EX

P1.2
P1.3
P1.4

40
41
42
43
44

P2.4

28
27

P2.3

26

P2.2

25

P2.1

24

P2.0
1
2
3
4
5
6

7

8

9

10

11

12

13

14

15

16

17

P1.5

P1.6

P1.7

RESET

NC

P3.0/RXD

P3.1/TXD

P3.2/INT0

P3.4/T0

P3.3/INT1

P3.5/T1/HPDI

23
22
21
20
19
18

NC

V

SS

XTAL1

XTAL2

P3.7/RD

P3.6/WR

NC : No-connection pin

44-Pin Plastic QFJ

7/40

PIN DESCRIPTIONS

Symbol Descriptipn

P0.0 to P0.7

Bidirectional I/O ports. They are also the data/address bus (input/output of data and output of
lower 8-bit address when external memory is accessed).
They are open-drain outputs when used as I/O ports, but 3-state outputs when used as data/address
bus.

MSM80C154S/83C154S¡ Semiconductor

P1.0 to P1.7

P2.0 to P2.7

P3.0 to P3.7

P1.0 to P1.7 are quasi-bidirectional I/O ports. They are pulled up internally when used as input
ports. Two of them have the following secondary functions:

•P1.0 (T2)

•P1.1 (T2EX)

P2.0 to P2.7 are quasi-bidirectional I/O ports. They also output the higher 8-bit address when
an external memory is accessed. They are pulled up internally when used as input ports.

P3.0 to P3.7 are quasi-bidirectional I/O ports. They are pulled up internally when used as input
ports. They also have the following secondary functions:

•P3.0 (RXD)
Serial data input/output in the I/O expansion mode and serial data input in the UART mode when

the serial port is used.

•3.1 (TXD)
Synchronous clock output in the I/O expansion mode and serial data output in the UART mode
when the serial port is used.

•3.2 (INT0)
Used as input pin for the external interrupt 0, and as count-up control pin for the timer/counter 0.

•3.3 (INT1)
Used as input pin for the external interrupt 1, and as count-up control pin for the timer/counter 1.

•3.4 (T0)
Used as external clock input pin for the timer/counter 0.

•3.5 (T1)
Used as external clock input pin for the timer/counter 1 and power-down-mode control input pin.

•3.6 (WR)
Output of the write-strobe signal when data is written into external data memory.

•3.7 (RD)
Output of the read-strobe signal when data is read from external data memory.

: used as external clock input pins for the timer/counter 2.
: used as trigger input for the timer/counter 2 to be reloaded or captured;
causing the timer/counter 2 interrupt.

ALE

PSEN

EA

Address latch enable output for latching the lower 8-bit address during external memory access.
Two ALE pulses are activated per machine cycle except during external data memory access at
which time one ALE pulse is skipped.

Program store enable output which enables the external memory output to the bus during external
program memory access. Two PSEN pulses are activated per machine cycle except during
external data memory access at which two PSEN pulses are skipped.

When EA is held at "H" level, the MSM 83C154S executes instructions from internal program
memory at address 0000H to 3FFFH, and executes instructions from external program memory
above address 3FFFH.
When EA is held at "L" level, the MSM80C154S/MSM83C154S executes instructions from external
program memory for all addresses.

8/40

PIN Descriptions (Continued)

Symbol Descriptipn

RESET

If this pin remains "H" for at least one machine cycle, the MSM80C154S/MSM83C154S is reset.
Since this pin is pulled down internally, a power-on reset is achieved by simply connecting a
capacitor between V

and this pin.

CC

MSM80C154S/83C154S¡ Semiconductor

XTAL1
XTAL2
V

CC

V

SS

Oscillator inverter input pin. External clock is input through XTAL1 pin.
Oscillator inverter output pin.
Power supply pin during both normal operation and standby operations.
GND pin.

9/40

REGISTERS

Diagram of Special Function Registers

MSM80C154S/83C154S¡ Semiconductor

REGISTER

NAME

IOCON

B

ACC

PSW

TH2

TL2

RCAP2H

RCAP2L

T2CON

IP

P3

IE

P2

SBUF

SCON

P1
TH1
TH0

TL1
TL0

TMOD

TCON
PCON

DPH

DPL

SP

P0

b7 b5 b4 b3 b2 b1 b0b6
FF

F7
E7
D7

CF
BF
B7
AF
A7

9F
97

8F

87

FE
F6
E6

D6

CE
BE
B6
AE
A6

9E
96

8E

86

BIT ADDRESS

FD
F5
E5
D5

CD
BD
B5
AD
A5

9D
95

8D

85

FC
F4
E4
D4

CC
BC
B4
AC
A4

9C
94

8C

84

FB
F3
E3
D3

CB
BB
B3
AB
A3

9B
93

8B

83

FA
F2
E2
D2

CA
BA
B2
AA
A2

9A
92

8A

82

F9
F1
E1

D1

C9
B9
B1
A9
A1

99
91

89

81

F8
F0
E0

D0

C8
B8
B0
A8
A0

98
90

88

80

DIRECT

ADDRESS

0F8H (248)
0F0H (240)
0E0H (224)

0D0H (208)

0CDH (205)

0CCH (204)
0CBH (203)
0CAH (202)
0C8H (200)
0B8H (184)
0B0H (176)
0A8H (168)
0A0H (160)

99H (153)
98H (152)
90H (144)
8DH (141)
8CH (140)
8BH (139)
8AH (138)
89H (137)
88H (136)
87H (135)
83H (131)
82H (130)
81H (129)
80H (128)

10/40

Special Function Registers

Timer mode register (TMOD)

MSM80C154S/83C154S¡ Semiconductor

NAME

TMOD 89H GATE C/T M1 M0 GATE C/T M1 M0

BIT LOCATION FLAG FUNCTION

TMOD.0 M0 M1 M0

TMOD.2 C/T

TMOD.3 GATE

TMOD.4 M0 M1 M0

TMOD.5 M1

TMOD.6 C/T

TMOD.7 GATE

ADDRESS

MSB LSB

76543210

Timer/counter 0 mode setting
00
01
10
11TMOD.1 M1

Timer/counter 0 count clock designation control bit.
XTAL1•2 divided by 12 clocks is the input applied to timer/counter 0 when
C/T = "0".
The external clock applied to the T0 pin is the input applied to timer/counter 0
when C/T = "1".

When this bit is "0", the TR0 bit of TCON (timer control register) is used to
control the start and stop of timer/counter 0 counting.
If this bit is "1", timer/counter 0 starts counting when both the TR0 bit of TCON
and INT0 pin input signal are "1", and stops counting when either is changed
to "0".

00
01
10
11

Timer/counter 1 count clock designation control bit.
XTAL1•2 divided by 12 clocks is the input applied to timer/counter 1 when
C/T = "0".
The external clock applied to the T1 pin is the input applied to timer/counter 1
when C/T = "1".

When this bit is "0", the TR1 bit of TCON is used to control the start and stop of
timer/counter 1 counting.
If this bit is "1", timer/counter 1 starts counting when both the TR1 bit of TCON
and INT1 pin input signal are "1", and stops counting when either is changed
to "0".

8-bit timer/counter with 5-bit prescalar.

16-bit timer/counter.

8-bit timer/counter with 8-bit auto reloading.

Timer/counter 0 separated into TLO (8-bit) timer/counter

and TH0 (8-bit) timer/counter. TF0 is set by TL0 carry, and

TF1 is set by TH0 carry.

Timer/counter 1 mode setting

8-bit timer/counter with 5-bit prescalar.

16-bit timer/counter

8-bit timer/counter with 8-bit auto reloading.

Timer/counter 1 operation stopped.

11/40

Power control register (PCON)

MSM80C154S/83C154S¡ Semiconductor

NAME

PCON 87H SMOD HPD RPD — GF1 GF0 PD IDL

BIT LOCATION FLAG FUNCTION

PCON.0 IDL

PCON.1 PD

PCON.5 RPD

ADDRESS

MSB LSB

76543210

IDLE mode is set when this bit is set to "1". CPU operations are stopped when
IDLE mode is set, but XTAL1•2, timer/counters 0, 1 and 2, the interrupt circuits,
and the serial port remain active. IDLE mode is cancelled when the CPU is reset
or when an interrupt is generated.

PD mode is set when this bit is set to "1". CPU operations and XTAL1•2 are
stopped when PD mode is set. PD mode is cancelled when the CPU is reset or
when an interrupt is generated.

General purpose bit.PCON.2 GF0
General purpose bit.PCON.3 GF1
Reserved bit. The output data is "1", if the bit is read.PCON.4 —
This bit is used to specify cancellation of CPU power down mode (IDLE or PD) by an

interrupt signal.
Power-down mode cannot be cancelled by an interrupt signal if the interrupt is not
enabled by IE (interrupt enable register) when this bit is "0".
If the interrupt flag is set to "1" by an interrupt request signal when this bit is
"1" (even if interrupt is disabled), the program is executed from the next address
of the power-down-mode setting instruction.
The flag is reset to "0" by software.

PCON.6 HPD

PCON.7 SMOD

The hard power-down setting mode in enabled when this bit is set to "1".
If the level of the power failure detect signal applied to the HPDI pin (pin 3.5)
is changed from "1" to "0" when this bit is "1", XTAL1•2 oscillation is stopped and
the system is put into hard power down mode. HPD mode is cancelled when the
CPU is reset.

When the timer/counter 1 carry signal is used as a clock in mode 1, 2 or 3 of
the serial port, this bit has the following functions.
The serial port operation clock is reduced by 1/2 when the bit is "0" for delayed
processing. When the bit is "1", the serial port operation clock is normal
for faster processing.

12/40

Timer control register (TCON)

MSM80C154S/83C154S¡ Semiconductor

NAME

TCON 88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0

BIT LOCATION FLAG FUNCTION

TCON.0 IT0

TCON.1 IE0

TCON.2 IT1

TCON.3 IE1

TCON.4 TR0

TCON.5 TF0

ADDRESS

MSB LSB

76543210

External interrupt 0 signal is used in level-detect mode when this bit is "0" and in
trigger detect mode when "1".

Interrupt request flag for external interrupt 0.
The bit is reset automatically when an interrupt is serviced.
The bit can be set and reset by software when IT0 = "1".

External interrupt 1 signal is used in level detect mode when this bit is "0", and in
trigger detect mode when "1".

Interrupt request flag for external interrupt 1.
The bit is reset automatically when an interrupt is serviced.
The bit can be set and reset by software when IT1 = "1".

Counting start and stop control bit for timer/counter 0.
Timer/counter 0 starts counting when this bit is "1", and stops counitng when "0".

Interrupt request flag for timer interrupt 0.
The bit is reset automatically when an interrupt is serviced.
The bit is set to "1" when a carry signal is generated from timer/counter 0.

TCON.6 TR1

TCON.7 TF1

Counting start and stop control bit for timer/counter 1.
The timer/counter 1 starts counting when this bit is "1", and stops counting when "0".

Interrupt request flag for timer interrupt 1.
The bit is reset automatically when interrupt is serviced.
The bit is set to "1" when carry signal is generated from timer/counter 1.

13/40

Serial port control register (SCON)

MSM80C154S/83C154S¡ Semiconductor

NAME

SCON 98H SM0 SM1 SM2 REN TB8 RB8 TI RI

BIT LOCATION FLAG FUNCTION

SCON.0 RI

SCON.1 TI

SCON.2 RB8

SCON.3 TB8

ADDRESS

MSB LSB

76543210

"End of serial port reception" interrupt request flag.
This flag must be reset by software during interrupt service routine.
This flag is set after the eighth bit of data has been received when in mode 0, or
by the STOP bit when in any other mode.
In mode 2 or 3, however, RI is not set if the RB8 data is "0" with SM2 = "1".
RI is set in mode 1 if STOP bit is received when SM2 = "1".

"End of serial port tramsmission" interrupt request flag. This flag must be reset
by software during interrupt service routine.
This flag is set after the eighth bit of data has been sent when in mode 0, or after
the last bit of data has been sent when in any other mode.

The ninth bit of data received in mode 2 or 3 is passed to RB8.
The STOP bit is applied to RB8 if SM2 = "0" when in mode 1.
RB8 can not be used in mode 0.

The TB8 data is sent as the ninth data bit when in mode 2 or 3.
Any desired data can be set in TB8 by software.

SCON.4 REN

SCON.5 SM2

SCON.6 SM1 SM0 SM1

SCON.7 SM0

Reception enable control bit.
No reception when REN = "0".
Reception enabled when REN = "1".

If the ninth bit of received data is "0" with SM2 = "1" in mode 2 or 3, the "end of
reception" signal is not set in the RI flag.
The "end of reception" signal set in the RI flag if the STOP bit is not "1" when
SM2 = "1" in mode 1.

00
01
10
11

MODE

0
1
2
3

8-bit shift register I/O
8-bit UART variable baud rate
9-bit UART 1/32 XTAL1, 1/64 XTAL1 baud rate
9-bit UART variable baud rate

14/40

Interrupt enable register (IE)

MSM80C154S/83C154S¡ Semiconductor

NAME

IE 0A8H EA — ET2 ES ET1 EX1 ET0 EX0

BIT LOCATION FLAG FUNCTION

IE.0 EX0

IE.1 ET0

IE.2 EX1

IE.3 ET1

IE.4 ES

ADDRESS

MSB LSB

76543210

Interrupt control bit for external interrupt 0.
Interrupt disabled when bit is "0".
Interrupt enabled when bit is "1".

Interrupt control bit for timer interrupt 0.
Interrupt disabled when bit is "0".
Interrupt enabled when bit is "1".

Interrupt control bit for external interrupt 1.
Interrupt disabled when bit is "0".
Interrupt enabled when bit is "1".

Interrupt control bit for timer interrupt 1.
Interrupt disabled when bit is "0".
Interrupt enabled when bit is "1".

Interrupt control bit for serial port.
Interrupt disabled when bit is "0".
Interrupt enabled when bit is "1".

IE.5 ET2

IE.6 —
IE.7 EA

Interrupt control bit for timer interrupt 2.
Interrupt disabled when bit is "0".
Interrupt enabled when bit is "1".

Reserved bit. The output data is "1" if the bit is read.
Overall interrupt control bit.

All interrupts are disabled when bit is "0".
All interrupts are controlled by IE.0 thru IE.5 when bit is "1".

15/40

Interrupt priority register (IP)

MSM80C154S/83C154S¡ Semiconductor

NAME

IP 0B8H PCT — PT2 PS PT1 PX1 PT0 PX0

BIT LOCATION FLAG FUNCTION

IP.0 PX0

IP.1 PT0

IP.2 PX1

IP.3 PT1

IP.4 PS

IP.5 PT2

IP.6 —
IP.7 PCT

ADDRESS

MSB LSB

76543210

Interrupt priority bit for external interrupt 0.
Priority is assigned when bit is "1".

Interrupt priority bit for timer interrupt 0.
Priority is assigned when bit is "1".

Interrupt priority bit for external interrupt 1.
Priority is assigned when bit is "1".

Interrupt priority bit for timer interrupt 1.
Priority is assigned when bit is "1".

Interrupt priority bit for serial port.
Priority is assigned when bit is "1".

Interrupt priority bit for timer interrupt 2.
Priority is assigned when bit is "1".

Reserved bit. The output data is "1" if the bit is read.
Priority interrupt circuit control bit.

The priority register contents are valid and priority assigned interrupts can be
processed when this bit is "0". When the bit is "1", the priority interrupt circuit is
stopped, and interrupts can only be controlled by the interrupt enable register (IE).

16/40

Program status word register (PSW)

MSM80C154S/83C154S¡ Semiconductor

NAME

ADDRESS

76543210

PSW 0D0H CY AC F0 RS1 RS0 OV F1 P

BIT LOCATION FLAG FUNCTION

MSB LSB

PSW.0 P

Accumulator (ACC) parity indicator.
This bit is "1" when the "1" bit number in the accumulator is an odd number, and
"0" when an even number.

User flag which may be set to "0" or "1" as desired by the user.PSW.1 F1

PSW.2 OV

Overflow flag which is set if the carry C6 from bit 6 of the ALU or CY is "1" as a
result of an arithmetic operation. The flag is also set to "1" if the resultant product
of executing multiplication instruction (MUL AB) is greater than 0FFH, but is reset
to "0" if the product is less than or equal to 0FFH.

RAM register bank switchPSW.3 RS0

RAM ADDRESS

PSW.4 RS1

RS1 RS0

00
01
10
11

BANK

0
1
2
3

00H - 07H
08H - 0FH
10H - 17H
18H - 1FH

User flag which may be set to "0" or "1" as desired by the user.PSW.5 F0

PSW.6 AC

Auxiliary carry flag.
This flag is set to "1" if a carry C

is generated from bit 3 of the ALU as a result of

3

executing an arithmetic operation instruction.
In all other cases, the flag is reset to "0".

PSW.7 CY

Main carry flag.
This flag is set to "1" if a carry C

is generated from bit 7 of the ALU as result of

7

executing an arithmetic operation instruction.
If a carry C

is not generated, the flag is reset to "0".

7

17/40

I/O control register (IOCON)

MSM80C154S/83C154S¡ Semiconductor

NAME

IOCON 0F8H — T32 SERR IZC P3HZ P2HZ P1HZ ALF

BIT LOCATION FLAG FUNCTION

IOCON.0 ALF

IOCON.1 P1HZ
IOCON.2 P2HZ
IOCON.3 P3HZ
IOCON.4 IZC

IOCON.5 SERR

IOCON.6 T32

ADDRESS

MSB LSB

76543210

If CPU power down mode (PD, HPD) is activated with this bit set to "1", the
outputs from ports 0, 1, 2, and 3 are switched to floating status.
When this bit is "0", ports 0, 1, 2, and 3 are in output mode.

Port 1 becomes a high impedance input port when this bit is "1".
Port 2 becomes a high impedance input port when this bit is "1".
Port 3 becomes a high impedance input port when this bit is "1".
The 10 kW pull-up resistor for ports 1, 2, and 3 is switched off when this bit

is "1", leaving only the 100 kW pull-up resistor.
Serial port reception error flag.

This flag is set to "1" if an overrun or framing error is generated when data is
received at a serial port.
The flag is reset by software.

Timer/counters 0 and 1 are connected serially to from a 32-bit timer/counter
when this bit is set to "1".
TF1 of TCON is set if a carry is generated in the 32-bit timer/counter.

IOCON.7 —

Leave this bit at "0".

18/40

Timer 2 control register (T2CON)

MSM80C154S/83C154S¡ Semiconductor

NAME

T2CON 0C8H TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2

BIT LOCATION FLAG FUNCTION

T2CON.0 CP/RL2

T2CON.1 C/T2

T2CON.2 TR2

T2CON.3 EXEN2

T2CON.4 TCLK

T2CON.5 RCLK

T2CON.6 EXF2

T2CON.7 TF2

ADDRESS

MSB LSB

76543210

Capture mode is set when TCLK + RCLK = "0" and CP/RL2 = "1".
16-bit auto reload mode is set when TCLK + RCLK = "0" and CP/RL2 = "0".
CP/RL2 is ignored when TCLK + RCLK = "1".

Timer/counter 2 count clock designation control bit.
The internal clocks (XTAL1•2 ÷ 12, XTAL1•2 ÷ 2) are used when this bit is "0",
and the external clock applied to the T2 pin is passed to timer/counter 2 when
the bit is "1".

Timer/counter 2 counting start and stop control bit.
Timer/counter 2 commences counting when this bit is "1" and stops counting
when "0".

T2EX timer/counter 2 external control signal control bit.
Input of the T2EX signal is disabled when this bit is "0", and enabled when "1".

Serial port transmit circuit drive clock control bit.
Timer/counter 2 is switched to baud rate generator mode when this bit is "1",
and the timer/counter 2 carry signal becomes the serial port transmit clock.
Note, however, that the serial ports can only use the timer/counter 2 carry signal
in serial port modes 1 and 3.

Serial port receive circuit drive clock control bit.
Timer/counter 2 is switched to baud rate generator mode when this bit is "1",
and the timer/counter 2 carry signal becomes the serial port transmit clock.
Note, however, that the serial ports can only use the timer/counter 2 carry signal
in serial port modes 1 and 3.

Timer/counter 2 external flag.
This bit is set to "1" when the T2EX timer/counter 2 external control signal level
is changed from "1" to "0" while EXEN2 = "1".
This flag serves as the timer interrupt 2 request signal. If an interrupt is
generated, EXF2 must be reset to "0" by software.

Timer/counter 2 carry flag.
This bit is set to "1" by a carry signal when timer/counter 2 is in 16-bit auto
reload mode or in capture mode.
This flag serves as the timer interrupt 2 request signal. If an interrupt is
generated, TF2 must be reset to "0" by software.

19/40

MEMORY MAPS

Program Area

MSM80C154S/83C154S¡ Semiconductor

65535

MSM83C154S EXTERNAL ROM AREA

16384
16383

MSM80C154S EXTERNAL ROM AREA

0FFFFH

4000H
3FFFH

44 002CH
43

002BH

Timer interrupt 2 start

S I/O interrupt start

Timer interrupt 1 start

External interrupt 1 start

Timer interrupt 0 start

External interrupt 0 start

002BH43

0023H35

001BH27

0013H19

000BH11

0003H3

0002H2

MSM83C154S INTERNAL ROM AREA

7 6 5 4 3 2 1 00

CPU reset start

0001H1

0000H0

20/40

MSM80C154S/83C154S¡ Semiconductor

Internal Data Memory and Special Function Register Layout Diagram

HEX

0FF

USER DATA RAM

REGISTER INDIRECT ADDRESSING

80
7F

IOCON

B

ACC

PSW

TH2

TL2

RCAP2H

RCAP2L

T2CON

IP

P3

IE

P2

SBUF

SCON

P1

TH1

SPECIAL FUNCTION REGISTERS

TH0

TL1
TL0

TMOD

TCON

PCON

DPH

DPL

SP
P0

FFH~F8H
F7H~F0H

E7H~E0H

D7H~D0H

CFH~C8H
BFH~B8H

B7H~B0H

AFH~A8H

A7H~A0H

9FH~98H
97H~90H

8FH~88H

87H~80H

248(0F8H)
240(0F0H)
224(0E0H)
208(0D0H)
205(0CDH)
204(0CCH)
203(OCBH)
202(0CAH)
200(0C8H)
184(0B8H)
176(0B0H)
168(0A8H)
160(0A0H)
153( 99H)
152( 98H)
144( 90H)
141( 8DH)
140( 8CH)
139( 8BH)
138( 8AH)
137( 89H)
136( 88H)
135( 87H)
131( 83H)
130( 82H)
129( 81H)
128( 80H)

30
2F

20
1F

18
17

10
0F

08
07

00

USER DATA RAM

7F

BIT RAM
7
R7

R0
R7

R0
R7

R0
R7

R0

BANK3

BANK2

BANK1

BANK0

78

0

BIT ADDRESSING

DATA ADDRESSING

21/40

Diagram of Internal Data Memory (RAM)

MSM80C154S/83C154S¡ Semiconductor

0FFH

80H

7FH

30H

2FH

2EH

2DH

2CH

2BH

2AH

29H

28H

27H

26H

7F

77

6F

67

5F

57

4F

47

3F

37

7E

76

6E

66

5E

56

4E

46

3E

36

USER DATA RAM

USER DATA RAM

7D

75

6D

65

5D

55

4D

45

3D

35

7C

74

6C

64

5C

54

4C

44

3C

34

7B

73

6B

63

5B

53

4B

43

3B

33

7A

72

6A

62

5A

52

4A

42

3A

32

79

71

69

61

59

51

49

41

39

31

78

70

68

60

58

50

48

40

38

30

255
128

127

48
47

46

45

44

43

42

41

40

39

38

BIT ADDRESSING

DATA ADDRESSING

25H

24H

23H

22H

21H

20H
1FH

18H
17H

10H
0FH

08H

07H

00H

2F

27

1F

17

0F

07

2E

26

1E

16

0E

06

2D

25

1D

15

0D

05

2C

24

1C

14

0C

04

Bank 3

Bank 2

Bank 1

Bank 0

2B

23

1B

13

0B

03

2A

22

1A

12

0A

02

29

21

19

11

09

01

28

20

18

10

08

00

37

36

35

34

33

32
31

24
23

16
15

8

REGISTER 0, 1, INDIRECT ADDRESSING

7

0

REGISTERS 0-7 DIRIECT ADDRESSING

22/40

ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Condition Rating Unit

Supply voltage
Input voltage
Storage temperature

T

V

CC

V

STG

I

Ta=25°C –0.5 to 7 V
Ta=25°C –0.5 to VCC+0.5 V

— –55 to +150 °C

RECOMMENDED OPERATING CONDITIONS

Parameter Symbol Condition Range Unit

Power supply voltage
Memory retension voltage
Oxcillation frequency
External clock operating

frequency
Ambient temperature

V

CC

V

CC

f

OSC

f

EXTCLK

f

Ta — –40 to +85 °C

See below. 2.0 to 6.0 V

=0 Hz (Oscillation stop) 2.0 to 6.0 V

OSC

See below. 1 to 24 MHz

See below. 0 to 24 MHz

MSM80C154S/83C154S¡ Semiconductor

*1 Depends on the specifications for the oscillator or ceramic resonater.

1

3

6

12

20
24

(ms)
t

CY

12

5
4

3

2

1

0.6

0.5

2.2

23456

(MHz)

EXTCLK

f

OSC

f

Power Supply Voltage (VCC)

23/40

ELECTRICAL CHARACTERISTICS

DC Characteristics 1

Parameter Symbol Condition Min. Typ. Max. Unit

Input Low Voltage V

Input High Voltage V

Input High Voltage V
Output Low Voltage
(PORT 1, 2, 3)
Output Low Voltage
(PORT 0, ALE, PSEN)

Output High Voltage
(PORT 1, 2, 3)

Output High Voltage
(PORT 0, ALE, PSEN)

Logical 0 Input Current/
Logical 1 Output Current/
(PORT 1, 2, 3)

Logical 1 to 0 Transition
Output Current (PORT 1, 2, 3)
Input Leakage Current
(PORT 0 floating, EA)
RESET Pull-down Resistance R

Pin Capacitance C

Power Down Current I

IL

Except XTAL1, EA,

IH

IH1

V

V

OL1

XTAL1, RESET and EA 0.7 V

OL

V

V

OH

V

V

OH1

VI=0.45 V

/ I

I

IL

OH

I

TL

I

RST

LI

V

Ta=25°C, f=1 MHz

IO

PD

(except XTAL1)

MSM80C154S/83C154S¡ Semiconductor

(V

=4.0 to 6.0 V, VSS=0 V, Ta=-40 to +85°C)

CC

— –0.5 — V

and RESET

0.2 V

+0.9 — V

CC

CC

IOL=1.6 mA — — V

IOL=3.2 mA — — V

IOH=–60 mA

2.4 — V

=5 V±10%

CC

=–30 mA 0.75 V

I

OH

=–10 mA 0.9 V

I

OH

CC

CC

IOH=–400 mA

2.4 — V

=5 V±10%

CC

=–150 mA 0.75 V

I

OH

=–40 mA 0.9 V

I

OH

CC

CC

–5 –20 mA

V

=0.45 V

O

VI=2.0 V — –190 mA

< VI < V

SS

CC

—— mA

—2040 kW

—— pF

—

—1 mA

0.2 VCC–0.1

V

+0.5

CC

—V

V

+0.5

CC

0.45

0.45

—

—V
—V

—
—

—

—V
—V

—
—

–80

–500

±10

125

10

50

Meas-

uring

circuit

1

2

3

2

—

4

24/40

Maximum power supply current normal operation ICC (mA)

MSM80C154S/83C154S¡ Semiconductor

V

CC

4 V 5 V 6 V

Freq

2.2 3.1 4.11 MHz

3.9 5.2 7.03 MHz

12.0 16.0 20.012 MHz

16.0 20.0 25.016 MHz

19.0 25.0 30.020 MHz

V

CC

4.5 V 5 V 6 V

Freq

25.0 29.0 35.024 MHz

Maximum power supply current idle mode ICC (mA)

V

CC

Freq

4 V 5 V 6 V

0.8 1.2 1.61 MHz

1.2 1.7 2.33 MHz

3.1 4.4 5.912 MHz

3.8 5.5 7.316 MHz

4.5 6.4 8.620 MHz

V

CC

Freq

4.5 V 5 V 6 V

6.4 7.4 9.824 MHz

25/40

DC Characteristics 2

Parameter Symbol Condition Min. Typ. Max. Unit

Input Low Voltage V

Input High Voltage V

Input High Voltage V
Output Low Voltage
(PORT 1, 2, 3)
Output Low Voltage
(PORT 0, ALE, PSEN)
Output High Voltage

Output High Voltage

MSM80C154S/83C154S¡ Semiconductor

(V

=2.2 to 4.0 V, VSS=0 V, Ta=-40 to +85°C)

CC

Meas-

uring

circuit

IL

— –0.5 — V

0.25 V

Except XTAL1, EA,

IH

IH1

V

OL

V

OL1

V

OH

and RESET

XTAL1, RESET, and EA 0.6 VCC+0.6 — V

IOL=10 mA—— V

IOL=20 mA—— V

IOH=–5 mA

0.25 V

+0.9 — V

CC

0.75 V

—V

CC

–0.1

CC

V

+0.5

CC

V

+0.5

CC

0.1

0.1
1

—

(PORT 1, 2, 3)

V

(PORT 0, ALE, PSEN)
Logical 0 Input Current/

Logical 1 Output Current/

I

IL

(PORT 1, 2, 3)
Logical 1 to 0 Transition

Output Current (PORT 1, 2, 3)
Input Leakage Current
(PORT 0 floating, EA)
RESET Pull-down Resistance R

Pin Capacitance C

Power Down Current I

OH1

/ I

I

TL

I

RST

PD

IOH=–20 mA

0.75 V

—V

CC

—

VI=0.1 V

OH

V

O

=0.1 V

–5 –10 mA

VI=1.9 V — –80 mA

V

LI

< VI < V

SS

CC

—— mA

—2040 kW

–40

–300

±10

125

2

3

2

Ta=25°C, f=1 MHz

IO

(except XTAL1)

—— pF

——1 mA

10

10

—

4

26/40

Maximum power supply current normal operation ICC (mA)

MSM80C154S/83C154S¡ Semiconductor

V

CC

2.2 V 3.0 V 4.0 V

Freq

0.9 1.4 2.21 MHz

1.8 2.4 4.33 MHz
— 8.0 12.012 MHz
— — 16.016 MHz

Maximum power supply current idle mode ICC (mA)

V

CC

Freq

2.2 V 3.0 V 4.0 V

0.3 0.5 0.81 MHz

0.5 0.8 1.23 MHz
— 2.0 3.112 MHz
— — 3.816 MHz

27/40

Measuring circuits

MSM80C154S/83C154S¡ Semiconductor

1

V

CC

V

IH

(*3)

V

IL

INPUT

V

SS

(*2)

OUTPUT

V A

(*1)

I

O

V

A

3

2

V

CC

INPUT

V

SS

4

OUTPUT

A

V

CC

V

IH

(*3)

V

IL

INPUT

V

SS

(*2)

OUTPUT

V A

V

CC

V

IH

(*3)

V

IL

INPUT

V

SS

OUTPUT

*1: Repeated for specified input pins.
*2: Repeated for specified output pins.
*3: Input logic for specified status.

28/40

AC Characteristics

(1) External program memory access AC characteristics

=2.2 to 6.0V, VSS=0V, Ta=–40°C to +85°C

V

CC

PORT 0, ALE, and PSEN connected with 100pF load, other connected with 80pF load

Variable clock from

Parameter Symble Unit

XTAL1, XTAL 2 Oscillation Cycle
ALE Signal Width
Address Setup Time
(to ALE Falling Edge)
Address Hold Time
(from ALE Falling Edge)
Instruction Data Read Time
(from ALE Falling Edge)
From ALE Falling Edge to PSEN

Falling Edge
PSEN Signal Width
Instruction Data Read Time
(from PSEN Falling Edge)
Instruction Data Hold Time
(from PSEN Rising Edge)
Bus Floating Time after Instruction
Data Read (from PSEN Rising Edge)
Instruction Data Read Time
(from Address Output)
Bus Floating Time(PSEN Rising
Edge from Address float)
Address Output Time from PSEN

Rising Edge

Min. Max.

t

CLCL

t

LHLL

t

AVLL

t

LLAX

t

LLPL

t

LLPL

t

PLPH

t

PLIV

t

PXIX

t

PXIZ

t

AVIV

t

AZPL

t

PXAV

41.7 1000 ns

2t

CLCL

1t

CLCL

1t

CLCL

—4t

1t

CLCL

3t

CLCL

—3t

0—ns

—1t

—5t

0—ns

1t

CLCL

1 to 24 MHz

-40 — ns

-15 — ns

-35 — ns

-30 — ns

-35 — ns

-20 — ns

MSM80C154S/83C154S¡ Semiconductor

*1

-100 ns

CLCL

-45 ns

CLCL

-20 ns

CLCL

-105 ns

CLCL

*1 The variable check is from 0 to 24 MHz when the external check is used.

29/40

(2) External program memory read cycle

t

LHLL

ALE

MSM80C154S/83C154S¡ Semiconductor

PSEN

PORT2

t

AVLL

A0 to A7

t

LLPL

t

LLAXtAZPL

t

LLIV

t

PLIV

t

PLPH

t

PXIX

INSTR

t

PXIZ

t

PXAV

A0 to A7PORT0

IN

t

AVIV

A8 to A15 A8 to A15 A8 to A15

30/40

(3) External data memory access AC characteristics

PORT 0, ALE, and PSEN connected with 100pF load, other connected with 80pF load

Parameter Symbol Unit

Min. Max.

XTAL1, XTAL2 Oscillator Cycle
ALE Signal Width
Address Setup Time
(to ALE Falling Edge)
Address Hold Time
(from ALE Falling Edge)

RD Signal Width
WR Signal Width

RAM Data Read Time
(from RD Signal Falling Edge)
RAM Data Read Hold Time
(from RD Signal Rising Edge)
Data Bus Floating Time
(from RD Signal Rising Edge)
RAM Data Read Time
(from ALE Signal Falling Edge)
RAM Data Read Time
(from Address Output)
RD/WR Output Time from ALE
Falling Edge
RD/WR Output Time from Address
Output
WR Output Time from Data Output
Time from Data to WR Rising Edge
Data Hold Time
(from WR Rising Edge)
Time from to Address Float RD
Output
Time from RD/WR Rising Edge to
ALE Rising Edge

t

CLCL

t

LHLL

t

AVLL

t

LLAX

t

RLRL

t

WLWH

t

RLDV

t

RHDX

t

RHDZ

t

LLDV

t

AVDV

t

LLWL

t

AVWL

t

QVWX

t

QVWH

t

WHQX

t

RLAZ

t

WHLH

*2

41.7 1000 ns

2t

CLCL

1t

CLCL

1t

CLCL

6t

CLCL

6t

CLCL

—5t

—2t

—8t

—9t

3t

CLCL

3t

CLCL

4t

CLCL

1t

CLCL

7t

CLCL

2t

CLCL

1t

CLCL

-40 — ns

-15 — ns

-35 — ns

-100 — ns

-100 — ns

0—ns

-40

-100

-70 — ns

-40 — ns

-105 — ns

-50 — ns

0—ns

-30

MSM80C154S/83C154S¡ Semiconductor

V

=2.2 to 6.0V, VSS=0V, Ta=–40°C to +85°C

CC

Variable clock from

1 to 24 MHz

*2

*1

-105 ns

CLCL

-70 ns

CLCL

-100 ns

CLCL

-105 ns

CLCL

+40 ns

3t

CLCL

+40

1t

CLCL

1t

+100

CLCL

ns

*1 The variable check is from 0 to 24 MHz when the external check is used.
*2 For 2.2£VCC<4 V

31/40

(4) External data memory read cycle

ALE

PSEN

RD

PORT 0

INSTR

IN

A0 to A7

PCL

t

LHLL

t

AVLL

A0 to A7

Rr or DPL

t

LLAX

t

AVWL

t

LLWL

t

AZRL

t

LLDV

t

AVDV

t

RLDV

MSM80C154S/83C154S¡ Semiconductor

t

RLRH

t

RHDX

DATA IN

t

WHLH

t

RHDZ

A0 to A7

PCL

PORT 2

PCH A8 to A15 PCH P2.0 to P2.7 DATA A8 to A15 DPHor A8 to A15 PCH

(5) External data memory write cycle

ALE

PSEN

WR

PORT 0

INSTR

IN

A0 to A7

PCL

t

LHLL

t

AVLL

A0 to A7

Rr or DPL

t

LLAX

t

AVWL

t

LLWL

t

QVWX

t

WLWH

t

QVWH

DATA (ACC)

t

WHLH

t

WHQX

A0 to A7

PCL

PORT 2

A8 to A15

PCH

A8 to A15 PCH P2.0 to P2.7 DATA A8 to A15 DPHor A8 to A15 PCH

32/40

(6) Serial port (I/O Extension Mode) AC characteristics

(V

CC

Parameter Symbol Min. Max. Unit

Serial Port Clock Cycle Time t
Output Data Setup to Clock Rising Edge t
Output Data Hold After Clock Rising Edge t
Input Data Hold After Clock Rising Edge t
Clock Rising Edge to Input Data Valid t

XLXL

QVXH

XHQX

XHDX

XHDV

12t

CLCL

10t

-133 —

CLCL

2t

-75 —

CLCL

0—

— 10t

MSM80C154S/83C154S¡ Semiconductor

=2.2 to 6.0V, VSS=0V, Ta=–40°C to +85°C)

—ns

ns
ns
ns

CLCL

-133

ns

33/40

34/40

MSM80C154S/83C154S¡ Semiconductor

t

XLXL

t

QVXH

t

XHQX

t

XHDV

t

XHDX

VALID VALID VALID VALID VALID VALID VALID VALID

MACHINE
CYCLE

ALE

SHIFT
CLOCK

OUTPUT
DATA

INPUT
DATA

(7) AC Characteristics Measuring Conditions

1.Input/output signal

MSM80C154S/83C154S¡ Semiconductor

V

OH

V

IH

V

IH

V

OH

TEST POINT

V

V

OL

IL

* The input signals in AC test mode are either VOH (logic "1") or V

V

IL

OL

V

OL

(logic "0") input signals
where logic "1" corresponds to a CPU output signal waveform measuring point in excess of
VIH, and logic "0" to a point below VIL.

2.Floating

V

OH

V

OL

V

IH

V

IL

Floating

V

V

IH

V

IL

OH

V

OL

* The port 0 floating interval is measured from the time the port 0 pin voltage drops below V

after sinking to GND at 2.4 mA when switching to floating status from a "1" output, and from
the time the port 0 pin voltage exceeds VIL after connecting to a 400 mA source when switching
to floating status from a "0" output.

IH

(8) XTAL1 external clock input waveform conditions

Parameter Symbol Min. Max. Unit

External Clock Freq. 1/t
Clock Pulse width 1 t
Clock Pulse width 2 t
Rise Time t
Fall Time t

CLCL

CHCx

CLCX

CLCH

CHCL

External Clock Drive Waveform

EXTERNAL
OSCILLATOR
SIGNAL

t

CHCX

t

CHCL

t

CLCX

0 24 MHz
15 —
15 —
—5
—5

0.7 V

CC

ns
ns
ns
ns

0.2 VCC - 0.1

t

CLCH

t

CLCL

35/40

Timing Diagram

,,,,,,

Basic timing

MSM80C154S/83C154S¡ Semiconductor

PCH

M1

M2

S1 S2 S3 S4 S5 S6

S1 S2 S3 S4 S5 S6

ACC & RAM

DPL&Rr

DATA STABLE

Instruction execution

PORT NEW DATA

Instruction execution

PC+1PC+1PC+1

TM+1

TM+1TM+1

Port output/input

instruction execution

execution

M1

M1

S1 S2 S3 S4 S5 S6

S1 S2 S3 S4 S5 S6

External data memory instruction

PCL PCL PCL PCL

Instruction decoding Instruction decodingInstruction decoding

PCL

DATA STABLE

PC+1

PCH PCH PCH PCHPCHDPH & PORT DATAPCH

Instruction execution

PCL

TM+1

PORT OLD DATA

Port output/input

instruction execution

PC+1

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

CYCLE

STEP

XTAL 1

ALE

PSEN

RD/WR

PORT-0

PORT-2

CPU¨PORT

PORT¨CPU

36/40

PACKAGE DIMENSIONS

DIP40-P-600-2.54

MSM80C154S/83C154S¡ Semiconductor

(Unit : mm)

Package material
Lead frame material
Pin treatment
Solder plate thickness
Package weight (g)

Epoxy resin
42 alloy
Solder plating
5 mm or more

6.10 TYP.

Notes for Mounting the Surface Mount Type Package

The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which
are very susceptible to heat in reflow mounting and humidity absorbed in storage.
Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the
product name, package name, pin number, package code and desired mounting conditions
(reflow method, temperature and times).

37/40

QFP44-P-910-0.80-2K

Mirror finish

MSM80C154S/83C154S¡ Semiconductor

(Unit : mm)

Package material
Lead frame material
Pin treatment
Solder plate thickness

Package weight (g)

Epoxy resin
42 alloy
Solder plating
5 mm or more

0.41 TYP.

Notes for Mounting the Surface Mount Type Package

The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which
are very susceptible to heat in reflow mounting and humidity absorbed in storage.
Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the
product name, package name, pin number, package code and desired mounting conditions
(reflow method, temperature and times).

38/40

QFJ44-P-S650-1.27

Mirror finish

MSM80C154S/83C154S¡ Semiconductor

(Unit : mm)

Package material
Lead frame material
Pin treatment
Solder plate thickness
Package weight (g)

Epoxy resin
Cu alloy
Solder plating
5 mm or more

2.00 TYP.

Notes for Mounting the Surface Mount Type Package

The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which
are very susceptible to heat in reflow mounting and humidity absorbed in storage.
Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the
product name, package name, pin number, package code and desired mounting conditions
(reflow method, temperature and times).

39/40

TQFP44-P-1010-0.80-K

Mirror finish

MSM80C154S/83C154S¡ Semiconductor

(Unit : mm)

Package material
Lead frame material
Pin treatment
Solder plate thickness
Package weight (g)

Epoxy resin
42 alloy
Solder plating
5 mm or more

0.28 TYP.

Notes for Mounting the Surface Mount Type Package

The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which
are very susceptible to heat in reflow mounting and humidity absorbed in storage.
Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the
product name, package name, pin number, package code and desired mounting conditions
(reflow method, temperature and times).

40/40