Please refer to "Product code guide (snap-in type)"
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Downsized snap-ins, 105℃
KMRSeries
Downsized 5mm in height from current snap-ins KMQ series
・
Max. 50% up ripple current than same case size of KMQ series
・
Endurance with ripple current : 2,000 hours at 105
・
dc
Rated voltage range : 160 to 450V
・
For inverter control, switching power supplies
・
Non solvent resistant type
・
RoHS2 Compliant
・
SPECIFICATIONS
◆
ItemsCharacteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
-25 to +105
160 to 450V
20% (M) (at 20℃, 120Hz)
±
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V) (at 20℃ after 5 minutes)
Rated voltage (V
Rated voltage (Vdc)160 to 250V315 to 400V420 & 450V
Z(-25℃)/Z(+20℃)488
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 105℃.
Capacitance change
D.F. (tanδ)
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
D.F. (tanδ)
Leakage current
, Capacitance range : 100 to 3,300µF
℃
dc
)160 to 250V315 to 400V420 & 450V
dc
℃
20% of the initial value
≦±
200% of the initial specified value
≦
The initial specified value
≦
15% of the initial value
≦±
150% of the initial specified value
≦
The initial specified value
≦
KMR
Downsized
KMQ
(at 20℃, 120Hz)tanδ(Max.)0.150.150.20
DIMENSIONS [mm]
◆
●
Sleeve (PET : Brown)
D+1max.
φ
PART NUMBERING SYSTEM
◆
±
2.5
L
E KM RV S NSM
4.0±0.5
Negative mark
Capacitance code (ex. 100µF:101, 2,700
PC board pin-out
(View from Solder side)
10
2
-
●
Sleeve (PET : Brown)
D+1max.
2
φ
φ
Vent
µ
L±2.5
Negative mark
±
1
4.5
PC board pin-out
(View from Solder side)
-
1.2×6
2
5±0.5
14.2±1
0.5
±
4.2
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001V 2021
Page 2
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001V 2021
Page 3
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5℃ rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001V 2021
Page 4
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
United Chemi-Con (UCC): EKMR201VSN681MP35SEKMR351VSN271MQ30SEKMR451VSN221MQ35SEKMR401VSN681MA40S