Datasheet IR2130, IR2132 Datasheet (IOR)

Data Sheet No. PD60019 Rev.P

IR2130/IR2132(J)(S) & (PbF)

3-PHASE BRIDGE DRIVER

Features

• Floating channel designed for bootstrap operation

Fully operational to +600V
Tolerant to negative transient voltage
dV/dt immune

• Gate drive supply range from 10 to 20V

• Undervoltage lockout for all channels

• Over-current shutdown turns off all six drivers

• Independent half-bridge drivers

Product Summary

V

OFFSET

IO+/- 200 mA / 420 mA

V

OUT

t

(typ.) 675 & 425 ns

on/off

600V max.

10 - 20V

• Matched propagation delay for all channels

• 2.5V logic compatible

• Outputs out of phase with inputs

• Cross-conduction prevention logic

Deadtime (typ.) 2.5 µs (IR2130)

0.8 µs (IR2132)

• Also available LEAD-FREE

Packages

Description

The IR2130/IR2132(J)(S) is a high voltage, high speed
power MOSFET and IGBT driver with three indepen­dent high and low side referenced output channels. Pro­prietary HVIC technology enables ruggedized
monolithic construction. Logic inputs are compatible with
CMOS or LSTTL outputs, down to 2.5V logic. A
ground-referenced operational amplifier provides
analog feedback of bridge current via an external cur­rent sense resistor. A current trip function which termi­nates all six outputs is also derived from this resistor.

FAULT

An open drain
rent or undervoltage shutdown has occurred. The output drivers feature a high pulse current buffer stage designed
for minimum driver cross-conduction. Propagation delays are matched to simplify use at high frequencies. The
floating channels can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration
which operate up to 600 volts.

signal indicates if an over-cur-

28-Lead SOIC

28-Lead PDIP

44-Lead PLCC w/o 12 Leads

Typical Connection

(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer
to our Application Notes and DesignTips for proper circuit board layout.

www.irf.com 1

IR2130/IR2132(J)(S) & (PbF)

Absolute Maximum Ratings

Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage param­eters are absolute voltages referenced to VS0. The Thermal Resistance and Power Dissipation ratings are measured
under board mounted and still air conditions. Additional information is shown in Figures 50 through 53.

Symbol Definition Min. Max. Units

V

B1,2,3

V

S1,2,3

V

HO1,2,3

V

CC

V

SS

V

LO1,2,3

V

IN

V

FLT

V

CAO

V

CA-

dVS/dt Allowable Offset Supply Voltage Transient — 50 V/ns

P

D

Rth

JA

T

J

T

S

T

L

High Side Floating Supply Voltage -0.3 625
High Side Floating Offset Voltage V
High Side Floating Output Voltage V

B1,2,3

S1,2,3

- 25 V

- 0.3 V

B1,2,3
B1,2,3

Low Side and Logic Fixed Supply Voltage -0.3 25
Logic Ground VCC - 25 V
Low Side Output Voltage -0.3 V
Logic Input Voltage (

HIN1,2,3, LIN1,2,3

& ITRIP) VSS - 0.3 (V

SS

(V

+ 0.3

CC

+ 0.3

CC

+ 15) or

+ 0.3)

CC

whichever is

lower

Output Voltage VSS - 0.3 V

FAULT

Operational Amplifier Output Voltage VSS - 0.3 V
Operational Amplifier Inverting Input Voltage VSS - 0.3 V

CC
CC
CC

+ 0.3
+ 0.3
+ 0.3

Package Power Dissipation @ TA ≤ +25°C (28 Lead DIP) — 1.5

(28 Lead SOIC) — 1.6 W

(44 Lead PLCC) — 2.0

Thermal Resistance, Junction to Ambient (28 Lead DIP) — 83

(28 Lead SOIC) — 78 °C/W

(44 Lead PLCC) — 63
Junction Temperature — 150
Storage Temperature -55 1 50
L ead Temperature (Soldering, 10 seconds) — 30 0

+ 0.3

+ 0.3

V

°C

Recommended Operating Conditions

The Input/Output logic timing diagram is shown in Figure 1. For proper operation the device should be used within the
recommended conditions. All voltage parameters are absolute voltages referenced to VS0. The VS offset rating is tested
with all supplies biased at 15V differential. Typical ratings at other bias conditions are shown in Figure 54.

Symbol Definition Min. Max. Units

V

B1,2,3

V

S1,2,3

V

HO1,2,3

V

CC

V

SS

V

LO1,2,3

V

IN

V

FLT

V

CAO

V

CA-

T

A

Note 1: Logic operational for VS of (VS0 - 5V) to (VS0 + 600V). Logic state held for VS of (VS0 - 5V) to (VS0 - VBS).
(Please refer to the Design Tip DT97-3 for more details).
Note 2: All input pins, CA- and CAO pins are internally clamped with a 5.2V zener diode.

2 www.irf.com

High Side Floating Supply Voltage V

S1,2,3

+ 10 V

S1,2,3

+ 20
High Side Floating Offset Voltage Note 1 600
High Side Floating Output Voltage V

S1,2,3

V

B1,2,3

Low Side and Logic Fixed Supply Voltage 10 20
Logic Ground -5 5
Low Side Output Voltage 0 V
Logic Input Voltage (

Output Voltage V

FAULT

Operational Amplifier Output Voltage V
Operational Amplifier Inverting Input Voltage V

HIN1,2,3, LIN1,2,3

& ITRIP) V

SS
SS
SS
SS

CC

VSS + 5

V

CC

VSS + 5
VSS + 5

Ambient Temperature -40 12 5 °C

V

IR2130/IR2132(J)(S) & (PbF)

Dynamic Electrical Characteristics

V

(VCC, V

BIAS

electrical characteristics are defined in Figures 3 through 5.

Symbol Definition Figure Min. Typ. Max. Units Test Conditions

t

on

t

off

t

r

t

f

t

itrip

t

bl

t

flt

t

flt,in

t

fltclr

DT Deadtime (IR2130) 18 1.3 2.5 3.7

SR+ Operational Amplifier Slew Rate (+) 19 4.4 6.2 —

SR- Operational Amplifier Slew Rate (-) 20 2.4 3.2 —

NOTE: For high side PWM, HIN pulse width must be ≥ 1.5µsec

Static Electrical Characteristics

V

(VCC, V

BIAS

are referenced to VSS and are applicable to all six logic input leads:
are referenced to V

BS1,2,3

) = 15V, V

= VSS, CL = 1000 pF and TA = 25°C unless otherwise specified. The dynamic

S0,1,2,3

Turn-On Propagation Delay 11 500 675 850
Turn-Off Propagation Delay 12 300 425 550 V
Turn-On Rise Time 13 — 80 125 V

S1,2,3

Turn-Off Fall Time 14 — 35 55
ITRIP to Output Shutdown Prop. Delay 15 400 660 920 VIN, V
ITRIP Blanking Time — — 400 — V

ns

ITRIP to FAULT Indication Delay 16 335 590 845 VIN, V
Input Filter Time (All Six Inputs) — — 310 — V

LIN1,2,3

to FAULT Clear Time 17 6.0 9.0 12.0 VIN, V

(IR2132) 18 0.4 0. 8 1.2

µs

V

V/µs

BS1,2,3

) = 15V, V

and are applicable to the respective output leads: HO1,2,3 or LO1,2,3.

S0,1,2,3

= VSS and TA = 25°C unless otherwise specified. The VIN, VTH and IIN parameters

S0,1,2,3

HIN1,2,3

&

LIN1,2,3

. The VO and IO parameters

= 0 & 5V

IN

= 0 to 600V

= 0 & 5V

ITRIP

= 1V

ITRIP

= 0 & 5V

ITRIP

= 0 & 5V

IN

= 0 & 5V

ITRIP

= 0 & 5V

IN

Symbol Definition Figure Min. Typ. Max. Units Test Conditions

V

IH

V

V

IT,TH+

V

OH

V

OL

I

LK

I

QBS

I

QCC

I

IN+

I

IN-

I

ITRIP+

I

ITRIP-

V

BSUV+

V

BSUV-

V

CCUV+

V

CCUV-

R

on,FLT

www.irf.com 3

Logic “0” Input Voltage (OUT = LO) 21 2.2 — —
Logic “1” Input Voltage (OUT = HI) 22 — — 0.8

IL

V

ITRIP Input Positive Going Threshold 23 400 490 580
High Level Output Voltage, V

- VO 24 — — 100 VIN = 0V, IO = 0A

BIAS

mV
Low Level Output Voltage, VO 25 — — 100 VIN = 5V, IO = 0A
Offset Supply Leakage Current 26 — — 50 VB = VS = 600V
Quiescent VBS Supply Current 27 — 15 30 VIN = 0V or 5V

µA

Quiescent VCC Supply Current 28 — 3 .0 4.0 mA VIN = 0V or 5V
Logic “1” Input Bias Current (OUT = HI) 29 — 4 50 650 VIN = 0V
Logic “0” Input Bias Current (OUT = LO) 30 — 2 25 400 VIN = 5V

µA
“High” ITRIP Bias Current 31 — 75 150 ITRIP = 5V
“Low” ITRIP Bias Current 32 — — 100 nA ITRIP = 0V
VBS Supply Undervoltage Positive Going 33 7.5 8.35 9.2
Threshold
VBS Supply Undervoltage Negative Going 34 7.1 7.95 8.8
Threshold
VCC Supply Undervoltage Positive Going 35 8.3 9. 0 9.7

V

Threshold
VCC Supply Undervoltage Negative Going 36 8.0 8. 7 9.4
Threshold

Low On-Resistance 37 — 55 75 Ω

FAULT

IR2130/IR2132(J)(S) & (PbF)

Static Electrical Characteristics -- Continued

V

(VCC, V

BIAS

are referenced to VSS and are applicable to all six logic input leads:
are referenced to V

Symbol Definition Figure Min. Typ. Max. Units Test Conditions

I

O+

I

O-

V

OS

I

CA-

CMRR Op. Amp. Common Mode Rejection Ratio 42 60 80 — VS0=V

PSRR Op. Amp. Power Supply Rejection Ratio 43 55 75 — VS0 = V

V

OH,AMP

V

OL,AMP

I

SRC,AMP

I

SRC,AMP

I

O+,AMP

I

O-,AMP

BS1,2,3

S0,1,2,3

) = 15V, V

and are applicable to the respective output leads: HO1,2,3 or LO1,2,3.

= VSS and TA = 25°C unless otherwise specified. The VIN, VTH and IIN parameters

S0,1,2,3

HIN1,2,3

&

LIN1,2,3

. The VO and IO parameters

Output High Short Circuit Pulsed Current 38 200 250 — VO = 0V, V

PW ≤ 10 µs

Output Low Short Circuit Pulsed Current 39 420 500 — VO = 15V, V

mA

PW ≤ 10 µs
Operational Amplifer Input Offset Voltage 40 — — 30 mV VS0 = V
CA- Input Bais Current 41 — — 4.0 nA V

dB

CA-

= 2.5V

CA-

=0.1V & 5V

CA-

CA-

VCC = 10V & 20V
Op. Amp. High Level Output Voltage 44 5.0 5.2 5.4 V V
Op. Amp. Low Level Output Voltage 45 — — 20 mV V
Op. Amp. Output Source Current 46 2.3 4.0 — V

Op. Amp. Output Sink Current 47 1.0 2.1 — V

mA

Operational Amplifier Output High Short 48 — 4. 5 6.5 V
Circuit Current V
Operational Amplifier Output Low Short 49 — 3 .2 5.2 V
Circuit Current V

= 0V, VS0 = 1V

CA-

= 1V, VS0 = 0V

CA-

= 0V, VS0 = 1V

CA-

V

CAO

= 1V, VS0 = 0V

CA-

V

CAO

= 0V, VS0 = 5V

CA-

CAO

= 5V, VS0 = 0V

CA-

CAO

IN

IN

= 0.2V

= 0.2V

= 4V

= 2V

= 0V

= 5V

= 0V

= 5V

Lead Assignments

28 Lead PDIP 44 Lead PLCC w/o 12 Leads 28 Lead SOIC (Wide Body)

IR2130 / IR2132 IR2130J / IR2132J IR2130S / IR2132S

Part Number

4 www.irf.com

Functional Block Diagram

IR2130/IR2132(J)(S) & (PbF)

Lead Definitions

Symbol Description

HIN1,2,3 Logic inputs for high side gate driver outputs (HO1,2,3), out of phase
LIN1,2,3 Logic inputs for low side gate driver output (LO1,2,3), out of phase
FAULT Indicates over-current or undervoltage lockout (low side) has occurred, negative logic
V

CC

ITRIP Input for over-current shutdown
CAO Output of current amplifier
CA- Negative input of current amplifier
V

SS

V

B1,2,3

HO1,2,3 High side gate drive outputs
V

S1,2,3

LO1,2,3 Low side gate drive outputs
V

S0

www.irf.com 5

Low side and logic fixed supply

Logic ground
High side floating supplies

High side floating supply returns

Low side return and positive input of current amplifier

IR2130/IR2132(J)(S) & (PbF)

HIN1,2,3

LIN1,2,3

ITRIP

FAULT

HO1,2,3

LO1,2,3

Figure 1. Input/Output Timing Diagram Figure 2. Floating Supply Voltage Transient Test Circuit

<50 V/ns

HIN1,2,3

50% 50%

HIN1,2,3
LIN1,2,3

50% 50%

LIN1,2,3

LO1,2,3

HO1,2,3

50% 50%

DT DT

HO1,2,3
LO1,2,3

t

t

r

on

90% 90%

10% 10%

t

t

off

f

Figure 3. Deadtime Waveform Definitions Figure 4. Input/Output Switching Time Waveform

Definitions

6 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

LIN1,2,3

ITRIP

FAULT

LO1,2,3

50%

50% 50%

50%

t

flt

t

itrip

50%

t

Figure 5. Overcurrent Shutdown Switching Time

Waveform Definitions

t

in,fil

HIN/LIN

on

high

HO/LO

fltclr

on on off

offoff

t

low

in,fil

U

Figure 5.5 Input Filter Function

V

S0

CA-

V

CC

+

­V

SS

V

SS

CAO

Figure 6. Diagnostic Feedback Operational Amplifier Circuit

www.irf.com 7

IR2130/IR2132(J)(S) & (PbF)

15V

V

3V

0V

3V

0V

SR+ =

CA­V

S0

∆T1 ∆T2

90%

∆V

10%

∆V

∆T1

+

-

SR- =

V

CC

SS

∆V

∆T2

Figure 7. Operational Amplifier Slew Rate

Measurement

15V

V

CC

-

CA-

+

V

S0

Measure V

CAO1

V

CAO2

CMRR = -20*LOG

V

SS

at VS0 = 0.1V

at V

= 5V

S0

(V

-0.1V) - (V

CAO1

CAO2

4.9V

CAO

50 pF

-5V)

CAO

(dB)

15V

20k

V

CC

+

­V

SS

V

VOS =

CAO

21

CAO

- 0.2V

0.2V

V

S0

CA-

+

1k

Figure 8. Operational Amplifier Input Offset Voltage

Measurement

V

CC

V

S0

0.2V

CA-

+

20k

1k

Measure V

PSRR = -20*LOG

+

­V

SS

at VCC = 10V

CAO1

V

at V

CAO2

= 20V

CC

V

CAO1

(10V) (21)

CAO

- V

CAO2

Figure 9. Operational Amplifier Common Mode

Rejection Ratio Measurements

Figure 10. Operational Amplifier Power Supply

Rejection Ratio Measurements

8 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

1.50

1.20

Max.

0.90

Typ.

0.60

Min.

Turn-On Delay Time (µs)

0.30

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

1.50
Max

1.20
Typ.

0.90

0.60

Turn-On Time (µs)

0.30

1.50

1.20

Max.

0.90

Typ.

0.60

Min.

Turn-On Delay Time (µs)

0.30

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 11B. Turn-On Time vs. Supply VoltageFigure 11A. Turn-On Time vs. Temperature

1.00

0.80

0.60

Max.

Typ.

0.40

Turn-Off Delay Time (µs)

Min.

0.20

0.00
0123456

Input Voltage (V)

Figure 11C. Turn-On Time vs. Voltage

1.00

0.80

Max.

0.60

Typ.

0.40

Min.

Turn-Off Delay Time (µs)

0.20

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 12B. Turn-Off Time vs. Supply Voltage

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 12A. Turn-Off Time vs. Temperature

1.50

1.20

0.90
Max

0.60

Turn-Off Time (µs)

0.30

Typ
Min.

0.00

0123456

Input Voltage (V)

Figure 12C. Turn-Off Time vs. Input Voltage

www.irf.com 9

IR2130/IR2132(J)(S) & (PbF)

250

200

150

Max.

100

Turn-On Rise Time (ns)

Typ.

50

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

250

200

Max.

150

Typ.

100

Turn-On Rise Time (ns)

50

0

10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 13A. Turn-On Rise Time vs. Temperature Figure 13B. Turn-On Rise Time vs. Voltage

125

100

75

50

Max.

Turn-Off Fall Time (ns)

Typ.

25

125

100

75

Max.

50

Typ.

Turn-Off Fall Time (ns)

25

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

0

10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 14A. Turn-Off Fall Time vs. Temperature Figure 14B. Turn-Off Fall Time vs. Voltage

1.50

1.20

Max.

0.90

Typ.

0.60

Min.

0.30

ITRIP to Output Shutdown Delay Time (µs)

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

1.50

1.20

Max.

0.90

Typ.

0.60

Min.

0.30

ITRIP to Output Shutdown Delay Time (µs)

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 15B. ITRIP to Output Shutdown Time vs. VoltageFigure 15A. ITRIP to Output Shutdown Time vs.

Temperature

10 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

1.50

1.20

Max.

0.90

Typ.

0.60

Min.

0.30

ITRIP to FAULT Indication Delay Time (µs)

0.00

-50 -25 0 25 50 75 100 125

Figure 16A. ITRIP to

Temperature (°C)

Indication Time vs.

FAULT

Temperature

25.0

20.0

15.0

Max.

Typ.

10.0

Min.

LIN1,2,3 to FAULT Clear Time (µs)

5.0

1.50

1.20

Max.

0.90

Typ.

0.60

Min.

0.30

ITRIP to FAULT Indication Delay Time (µs)

0.00
10 12 14 16 18 20

Figure 16B. ITRIP to

25.0

20.0

15.0

Max.

Typ.

10.0

Min.

LIN1,2,3 to FAULT Clear Time (µs)

5.0

V

Supply Voltage (V)

CC

Indication Time vs. Voltage

FAULT

0.0

-50 -25 0 25 50 75 100 125

Figure 17A.

LIN1,2,3

Temperature (°C)

to

FAULT

Clear Time vs.

0.0
10 12 14 16 18 20

Figure 17B.

LIN1,2,3

V

Supply Voltage (V)

CC

to

FAULT

Clear Time vs. Voltage

Temperature

7.50

6.00

Max.

4.50

Typ.

3.00

Deadtime (µs)

Min.

1.50

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

7.50

6.00

4.50

Max.

3.00

Deadtime (µs)

Typ.

Min.

1.50

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 18A. Deadtime vs. Temperature (IR2130) Figure 18B. Deadtime vs. Voltage (IR2130)

www.irf.com 11

IR2130/IR2132(J)(S) & (PbF)

2.50

2.00

1.50

Max.

Typ.

1.00

Deadtime (µs)

Min.

0.50

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

2.50

2.00

1.50

Max.

1.00

Deadtime (µs)

Typ.

Min.

0.50

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 18C. Deadtime vs. Temperature (IR2132) Figure 18D. Deadtime vs. Voltage (IR2132)

10.0

8.0

Typ.

6.0

Min.

4.0

Amplifier Slew Rate + (V/µs)

2.0

10.0

8.0

Typ.

6.0

Min.

4.0

Amplifier Slew Rate + (V/µs)

2.0

0.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

0.0
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 19A. Amplifier Slew Rate (+) vs. Temperature Figure 19B. Amplifier Slew Rate (+) vs. Voltage

5.00

4.00

Typ.

3.00

Min.

2.00

Amplifier Slew Rate - (V/µs)

1.00

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

5.00

4.00

Typ.

3.00

Min.

2.00

Amplifier Slew Rate - (V/µs)

1.00

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 20A. Amplifier Slew Rate (-) vs. Temperature Figure 20B. Amplifier Slew Rate (-) vs. Voltage

12 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

5.00

4.00

3.00

Min.

2.00

Logic "0" Input Threshold (V)

1.00

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

5.00

4.00

3.00

Min.

2.00

Logic "0" Input Threshold (V)

1.00

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 21A. Logic “0” Input Threshold vs. Temperature Figure 20B. Logic “0” Input Threshold vs. Voltage

5.00

4.00

3.00

2.00

Logic "1" Input Threshold (V)

1.00

Max.

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

5.00

4.00

3.00

2.00

Logic "1" Input Threshold (V)

1.00

Max.

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 22A. Logic “1” Input Threshold vs. Temperature Figure 22B. Logic “1” Input Threshold vs. Voltage

750

Max.

600

Typ.

450

Min.

300

150

ITRIP Input Positive Going Threshold (mV)

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 23A. ITRIP Input Positive Going Threshold

vs. Temperature

750

Max.

600

Typ.

450

Min.

300

150

ITRIP Input Positive Going Threshold (mV)

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 23B. ITRIP Input Positive Going Threshold

vs. Voltage

www.irf.com 13

IR2130/IR2132(J)(S) & (PbF)

1.00

0.80

0.60

0.40

High Level Output Voltage (V)

0.20

Max.

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

1.00

0.80

0.60

0.40

High Level Output Voltage (V)

0.20

Max.

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 24A. High Level Output vs. Temperature Figure 24B. High Level Output vs. Voltage

1.00

0.80

0.60

0.40

Low Level Output Voltage (V)

0.20

Max.

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

1.00

0.80

0.60

0.40

Low Level Output Voltage (V)

0.20

Max.

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 25A. Low Level Output vs. Temperature Figure 25B. Low Level Output vs. Voltage

500

400

300

200

Offset Supply Leakage Current (µA)

100

Max.

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 26A. Offset Supply Leakage Current

500

400

300

200

100

Offset Supply Leakage Current (µA)

Max.

0

0 100 200 300 400 500 600

V

Boost Voltage (V)

B

Figure 26B. Offset Supply Leakage Current vs. Voltage

vs. Temperature

14 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

100

80

60

40

Supply Current (µA)

BS

V

Max.

20

Typ.

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

100

80

60

40

Supply Current (µA)

BS

V

Max.

20

Typ.

0

10 12 14 16 18 20

V

Floating Supply Voltage (V)

BS

Figure 27A. VBS Supply Current vs. Temperature Figure 27B. VBS Supply Current vs. Voltage

10.0

8.0

6.0

4.0

Supply Current (mA)

Max.

CC

V

Typ.

2.0

10.0

8.0

6.0

4.0

Supply Current (mA)

CC

Max.

V

2.0

Typ.

0.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

0.0
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 28A. VCC Supply Current vs. Temperature Figure 28B. VCC Supply Current vs. Voltage

1.25

1.00

0.75

0.50

Max.

Typ.

Logic "1" Input Bias Current (mA)

0.25

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

1.25

1.00

0.75

0.50

Max.

Typ.

Logic "1" Input Bias Current (mA)

0.25

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 29A. Logic “1” Input Current vs. Temperature Figure 29A. Logic “1” Input Current vs. Voltage

www.irf.com 15

IR2130/IR2132(J)(S) & (PbF)

1.25

1.00

0.75

0.50

Max.

Logic "0" Input Bias Current (mA)

0.25

Typ.

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

1.25

1.00

0.75

0.50

Max.

Logic "0" Input Bias Current (mA)

0.25

Typ.

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 30A. Logic “0” Input Current vs. Temperature Figure 30B. Logic “0” Input Current vs. Voltage

500

400

300

200

Max.

"High" ITRIP Bias Current (µA)

100

Typ.

500

400

300

200

Max.

"High" ITRIP Bias Current (µA)

100

Typ.

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 31A. “High” ITRIP Current vs. Temperature Figure 31B. “High” ITRIP Current vs. Voltage

250

200

150

100

Max.

"Low" ITRIP Bias Current (nA)

50

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

500

400

300

200

"Low" ITRIP Bias Current (µA)

Max.

100

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 32A. “Low” ITRIP Current vs. Temperature Figure 32B. “Low” ITRIP Current vs. Voltage

16 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

11.0

10.0

Max.

9.0

Typ.

8.0

Undervoltage Lockout + (V)

Min.

BS

V

7.0

6.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

11.0

10.0

9.0

Max.

8.0

Typ.

Undervoltage Lockout - (V)

BS

V

Min.

7.0

6.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 33. VBS Undervoltage (+) vs. Temperature Figure 34. VBS Undervoltage (-) vs. Temperature

11.0

10.0

Max.

Typ.

9.0

Min.

8.0

Undervoltage Lockout + (V)

CC

V

7.0

6.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

11.0

10.0

Max.

9.0

Typ.

Min.

8.0

Undervoltage Lockout - (V)

CC

V

7.0

6.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 35. VCC Undervoltage (+) vs. Temperature Figure 36. VCC Undervoltage (-) vs. Temperature

250

200

150

100

Max.

FAULT- Low On Resistance (ohms)

50

Typ.

0

-50 -25 0 25 50 75 100 125

Figure 37A.

Temperature (°C)

Low On Resistance vs.

FAULT

250

200

150

Max.

100

Typ.

FAULT- Low On Resistance (ohms)

50

0

10 12 14 16 18 20

Figure 37B.

FAULT

V

Supply Voltage (V)

CC

Low On Resistance vs. Voltage

Temperature

www.irf.com 17

IR2130/IR2132(J)(S) & (PbF)

500

400

Typ.

300

Min.

200

Output Source Current (mA)

100

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

500

400

300

200

Typ.

Output Source Current (mA)

100

Min.

0

10 12 14 16 18 20

V

Supply Voltage (V)

BIAS

Figure 38A. Output Source Current vs. Temperature Figure 38B. Output Source Current vs. Voltage

750

Typ.

600

Min.

450

300

Output Sink Current (mA)

150

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

750

625

500

375

Typ.

250

Output Sink Current (mA)

Min.

125

0

10 12 14 16 18 20

Supply Voltage (V)

V

BIAS

Figure 39A. Output Sink Current vs. Temperature Figure 39B. Output Sink Current vs. Voltage

50

40

Max.

30

20

Amplifier Input Offset Voltage (mV)

10

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

50

40

30

Max.

20

Amplifier Input Offset Voltage (mV)

10

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 40A. Amplifier Input Offset vs. Temperature Figure 40B. Amplifier Input Offset vs. Voltage

18 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

10.0

8.0

6.0

Max.

4.0

CA- Input Bias Current (nA)

2.0

0.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

10.0

8.0

6.0

Max.

4.0

CA- Input Bias Current (nA)

2.0

0.0
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 41A. CA- Input Current vs. Temperature Figure 41B. CA- Input Current vs. Voltage

100

Typ.

80

Min.

60

40

Amplifier CMRR (dB)

20

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

100

Typ.

80

Min.

60

40

Amplifier CMRR (dB)

20

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 42A. Amplifier CMRR vs. Temperature Figure 42B. Amplifier CMRR vs. Voltage

100

80

Typ.

60

Min.

40

Amplifier PSRR (dB)

20

0

-50 -25 0 25 50 75 100 125

Temperature (°C)

Figure 43A. Amplifier PSRR vs. Temperature

100

80

Typ.

60

Min.

40

Amplifier PSRR (dB)

20

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 43B. Amplifier PSRR vs. Voltage

www.irf.com 19

IR2130/IR2132(J)(S) & (PbF)

6.00

5.70

5.40

Max.

Typ.

5.10

Min.

4.80

Amplifier High Level Output Voltage (V)

4.50

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 44A. Amplifier High Level Output vs.

Temperature

100

80

60

40

Max.

20

Amplifier Low Level Output Voltage (mV)

0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 45A. Amplifier Low Level Output vs.

Temperature

10.0

6.00

5.70

Max.

5.40

Typ.

5.10

Min.

4.80

Amplifier High Level Output Voltage (V)

4.50
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 44B. Amplifier High Level Output vs. Voltage

100

80

60

40

Max.

20

Amplifier Low Level Output Voltage (mV)

0

10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 45B. Amplifier Low Level Output vs. Voltage

10.0

8.0

6.0

Typ.

4.0

Min.

2.0

Amplifier Output Source Current (mA)

0.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 46A. Amplifier Output Source Current vs.

Temperature

8.0

6.0

4.0

Typ.

2.0

Amplifier Output Source Current (mA)

Min.

0.0
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 46B. Amplifier Output Source Current vs.

Voltage

20 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

5.00

4.00

3.00

Typ.

2.00

Min.

Amplifier Output Sink Current (mA)

1.00

0.00

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 47A. Amplifier Output Sink Current vs.

Temperature

15.0

12.0

9.0

Max.

6.0

Typ.

3.0

Output High Short Circuit Current (mA)

0.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 48A. Amplifier Output High Short Circuit

Current vs. Temperature

15.0

5.00

4.00

3.00

2.00

Typ.

Min.

Amplifier Output Sink Current (mA)

1.00

0.00
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 47B. Amplifier Output Sink Current vs. Voltage

15.0

12.0

9.0

6.0

Max.

3.0

Output High Short Circuit Current (mA)

Typ.

0.0
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 48B. Amplifier Output High Short Circuit

Current vs. Voltage

15.0

12.0

9.0

Max.

6.0

Typ.

3.0

Output Low Short Circuit Current (mA)

0.0

-50 -25 0 25 50 75 100 125
Temperature (°C)

Figure 49A. Amplifier Output Low Short Circuit Current

vs. Temperature

12.0

9.0

6.0

Max.

3.0

Output Low Short Circuit Current (mA)

Typ.

0.0
10 12 14 16 18 20

V

Supply Voltage (V)

CC

Figure 49B. Amplifier Output Low Short Circuit Current

vs. Voltage

www.irf.com 21

IR2130/IR2132(J)(S) & (PbF)

0.0

-3.0

Typ.

-6.0

-9.0

Offset Supply Voltage (V)

S

V

-12.0

-15.0
10 12 14 16 18 20

Figure 50. Maximum VS Negative Offset vs. V

50

45

V

Floating Supply Voltage (V)

BS

480V

Supply Voltage

BS

50

45

480V

40

35

30

Junction Temperature (°C)

25

20

1E+2 1E+3 1E+4 1E+5

Frequency (Hz)

Figure 51. IR2130/IR2132 TJ vs. Frequency (IRF820)

R

GATE

100

80

60

Junction Temperature (°C)

40

20

1E+2 1E+3 1E+4 1E+5

ΩΩ

= 33

Ω, VCC = 15V

ΩΩ

Frequency (Hz)

Figure 53. IR2130/IR2132 TJ vs. Frequency (IRF840)

R

GATE

ΩΩ

= 15

Ω, VCC = 15V

ΩΩ

0V

480V
320V

160V

320V

160V

0V

40

35

30

Junction Temperature (°C)

25

20

1E+2 1E+3 1E+4 1E+5

Frequency (Hz)

Figure 52. IR2130/IR2132 TJ vs. Frequency (IRF830)

R

GATE

140

120

100

80

60

Junction Temperature (°C)

40

20

1E+2 1E+3 1E+4 1E+5

ΩΩ

= 20

Ω, VCC = 15V

ΩΩ

Frequency (Hz)

Figure 54. IR2130/IR2132 TJ vs. Frequency (IRF450)

R

GATE

ΩΩ

= 10

Ω, VCC = 15V

ΩΩ

480V

320V

160V

0V

320V

160V
0V

22 www.irf.com

IR2130/IR2132(J)(S) & (PbF)

120
110
100

90
80
70
60
50
40

Junction Tem per atur e ( ° C)

30
20

1E+2 1E+3 1E+4 1E+5

Figure 55. IR2130J/IR2132J

TJ vs. Frequency (IRGPC20KD2)

R

GATE

Frequency (Hz)

ΩΩ

= 33

Ω, VCC = 15V

ΩΩ

120
110
100

90
80
70
60
50
40
30

Junc tion Temper atur e ( °C)

20

1E+2 1E+3 1E+4 1E+5

Frequency (Hz)

Figure 57. IR2130J/IR2132J

TJ vs. Frequency (IRGPC40KD2)

R

GATE

ΩΩ

= 15

Ω, VCC = 15V

ΩΩ

480V

320V

160V

0V

480V
320V

160V
0V

120
110
100

90
80
70
60
50
40

Junction Tem per atur e ( ° C)

30
20

1E+2 1E+3 1E+4 1E+5

Frequency (Hz)

Figure 56. IR2130J/IR2132J

TJ vs. Frequency (IRGPC30KD2)

R

GATE

ΩΩ

= 20

Ω, VCC = 15V

ΩΩ

120
110
100

90
80
70
60
50
40

Ju nctio n T em p e ra ture (°C )

30
20

1E+2 1E+3 1E+4 1E+5

Frequency (Hz)

Figure 58. IR2130J/IR2132J

TJ vs. Frequency (IRGPC50KD2)

R

GATE

ΩΩ

= 10

Ω, VCC = 15V

ΩΩ

480V

320V
160
0V

480V

320V

160V
0V

www.irf.com 23

IR2130/IR2132(J)(S) & (PbF)

Case outlines

28-Lead PDIP (wide body)

01-3024 02

01-304002

(MS-013AE)28-Lead SOIC (wide body)

01-6011

(MS-011AB)

01-6013

24 www.irf.com

Case outline

IR2130/IR2132(J)(S) & (PbF)

NOTES

44-Lead PLCC w/o 12 leads

www.irf.com 25

01-3004 02(mod.) (MS-018AC)

01-6009 00

IR2130/IR2132(J)(S) & (PbF)

LEADFREE PART MARKING INFORMATION

Part number

Date code

Pin 1
Identifier

?

MARKING CODE

Lead Free Released

P

Non-Lead Free
Released

IRxxxxxx

YWW?

ORDER INFORMATION

Basic Part (Non-Lead Free)

28-Lead PDIP IR2130 order IR2130
28-Lead SOIC IR2130S order IR2130S
28-Lead PDIP IR2132 order IR2132
28-Lead SOIC IR2132S order IR2132S
44-Lead PLCC IR2130J order IR2130J
44-Lead PLCC IR2132J order IR2132J

IR logo

?XXXX

Lot Code

(Prod mode - 4 digit SPN code)

Assembly site code
Per SCOP 200-002

Leadfree Part

28-Lead PDIP IR2130 order IR2130PbF
28-Lead SOIC IR2130S order IR2130SPbF
28-Lead PDIP IR2132 order IR2132PbF
28-Lead SOIC IR2132S order IR2132SPbF
44-Lead PLCC IR2130J order IR2130JPbF
44-Lead PLCC IR2132J order IR2132JPbF

IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: [phone]

Data and specifications subject to change without notice. 4/2/2004

26 www.irf.com

This product has been qualified per industrial level