Datasheet HPT015YEHH-A, HPT015YEJJ-A, HPT015YGHH-A, HPT015YGJJ-A, HPT015ZEHH-A Datasheet (Power-one)

...

Download

Page 1

(888) IPD-CONVerters

●

(888) 473-2668

HPT SERIES - TRIPLE OUTPUT, 15 WATT

DESCRIPTION FEATURES

●

www.ipdconverters.com

HPT triple output DC/DC converters provide 15 Watts of output power in an industry standard package. HPT’s feature excellent efficiency and industry-leading power density. The HPT has openframe packaging to provide maximum useable power with minimal thermal constraints. These units are fully compatible with production board washing processes.

TECHNICAL SPECIFICA TIONS

Input

Voltage Range

24 VDC Nominal 10 - 30 VDC 48 VDC Nominal 34 - 75 VDC 48 VDC Wide 20 - 60 VDC

Output

Setpoint Accuracy ±1 % Auxiliary Setpoint Accuracy 5%

Line Regulation Vin Min. - Vin Max., I Load Regulation I Minimum Output Current 10 % I Dynamic Regulation, Loadstep 25% I

Pk Deviation 1% V

Settling Time 250 µs Ripple and Noise w/ 25 MHz BW, Pk-Pk / RMS 1% / 0.3% V Current Limit Type Hiccup Current Limit Threshold Range, % of I Short Circuit Current Max. 200% I OVP Trip Range 110 - 140% V OVP Type Second Control Loop

Min. - I

out

Rated ±1% V

out

Max., Vin Nom. ±1% V

Rated

out

Rated 110 - 140%

out

Nom.

out

Nom.

out

• Triple Output 2” X 2”

• Open-Frame Packaging

• 2.5 Million Hours MTBF

• Short Circuit and Overvoltage Protection

• 500V Isolation

out out

out

• Input Undervoltage Lockout

• 3-1 Wide Voltage Input

• 100°C Baseplate Operation

General

Switching Frequency 200 kHz Isolation

Input - Output 500 VDC Input - Case 500 VDC

Output - Case 500 VDC Temperature Coefficient 0.02 ppm/°C Case Temperature

Operating Range -40 to +100°C

Storage Range -40 to +125°C Thermal Shutdown Range 105 to 115°C Humidity Max., Non-Condensing 95% Vibration, 3 Axes, 5 Min Each 2 g MTBF† (Bellcore TR-NWT-000332) 2.5 x 106 hrs Safety Consult Factory Weight (approx.) 0.85 oz

Notes

For negative logic, add suffix “N” to model number.

†

MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with

commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory

for specific model information. Units are water-washable and fully compatible with commercial spray or immersion

post wave-solder washing equipment.

Page 2

HPT SERIES - TRIPLE OUTPUT, 15 WATT

MODELS - (See the last page of this file for options.)

Vin

(Volts)

24 24 24 24 48 48 48

48 48 WIDE 48 WIDE 48 WIDE 48 WIDE

Vin Range

(Volts)

18 - 36 18 - 36 18 - 36 18 - 36 34 - 75 34 - 75 34 - 75 34 - 75 20 - 60 20 - 60 20 - 60 20 - 60

Iin Max.*

(Amps)

1.90

1.84

0.56

0.54

0.95

0.92

Denotes advanced product release. Consult factory for product availability. * Max imum input c urrent at minimum input vol tage, maxi mum rated output power. ** At nominal Vi n, rate d output.

MECHANICAL DRAWING

2.00"

(50.8mm)

Vout

(Volts)

3.3, –12

3.3, –15 5, – 12 5, – 15

3.3, –12

3.3, –15 5, – 12 5, – 15

3.3, –12

3.3, –15 5, – 12 5, – 15

Iout Rated

(Amps)

2.3, – 0.3 1

2.3, – 0.2 5

1.5, – 0.3 1

1.5, – 0.2 5

2.3, – 0.3 1

2.3, – 0.2 5

1.5, – 0.3 1

1.5, – 0.2 5

2.3, – 0.3 1

2.3, – 0.2 5

1.5, – 0.3 1

1.5, – 0.2 5

1.200"(30.5mm)

Ripple & Noise

Pk-Pk (mV)

100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200 100, – 200

Effici ency

Typ. **

80% 80% 83% 83% 80% 80% 83% 83% 80% 80% 83% 83%

0.18"

(4.6mm)

Model

HPT0 15YEHH-A HPT0 15YEJJ -A HPT0 15YGHH-A HPT015YGJJ-A HPT0 15ZEHH-AS 1 HPT0 15ZEJJ- AS1 HPT0 15ZGHH-AS 1 HPT0 15ZGJJ-AS 1 HPT0 15ZEHH-A HPT0 15ZEJJ- A HPT0 15ZGHH-A HPT0 15ZGJJ-A

0.700"(17.8mm)

0.500"(12.7mm)

-0.40"(-10.2mm)

Thermal Impedance

Natural Convection 11.2 °C/W 100 LFM 9.6 °C/W 200 LFM 6.8 °C/W 300 LFM 5.1 °C/W 400 LFM 4.2 °C/W

Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application.

1.800"(45.7mm)

BOTTOM VIEW

-0.10"(-2.5mm)

Pin Function

1+V 2-V 3+V 4+V 5-V 6-V

0.800"(20.3mm)

0.400"(10.2mm)

out

out out out

2.00"

(50.8mm)

DIA 0.040"

(1.0mm)

0.025" REF. (0.6mm)

0.40"

(10.2mm)

Tolerances

Inches: (Millimeters) .XX ± 0.020 .X ± 0.5 .XXX ± 0.010 .XX ± 0.25

Pin: ± 0.002 ± 0.05

(Dimensions as listed unless otherwise specified.)

Page 3

OPTIONS

When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table.

OPTION SUFFIX APPLICABLE SERIES REMARKS

Negative Logic N HAS, HBD, HBS, HES, LES, QBS,

Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS XWS, XWD, XWT Trim 1 IAS, LES Enable 2 I A D, IAS, LES, SMS Trim and Enable 3 I AS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS

PIN LENGTH AND HEATSINK OPTIONS

0.110” (2.8mm) Pin Length 8 All Units (Except SMS)

0.150” (3.8mm) Pin Length 9 All Units (Except SMS)

0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM

0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM

0.45” (11.4mm) Horizontal Heatsink

0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM

0.95” (24.1mm) Horizontal Heatsink

0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM

2H All Units (Except DIP, SIP, and SM

3H All Units (Except DIP, SIP, and SM

QES, TES, TQD

Packages)

TTL “Low” Turns Module ON TTL “High” Turns Module OFF

Standard Pin Length is 0.180” (4.6mm)

Includes Thermal Pad

Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and

0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.

NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,

equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.

TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.