Datasheet FDC05-12S15, FDC05-12S12, FDC05-12S05, FDC05-12D15, FDC05-12D12 Datasheet (P-DUKE)

...

Download

Page 1

OUTPUT SPEC IFICATIONS

Output power 5 Watts max Voltage accuracy Full load and nominal Vin ± 2% Minimum load (Note 1)

10% of FL

Line regulation LL to HL at Full Load

± 0.2%

Load regulation

10% to 100% FL Single

Dual

± 0.2%

± 1%

Cross regulation (Dual) Asymmetrical load 25% / 100% FL ± 5% Ripple and noise 20MHz bandwidth 50mVp-p Temperature coefficient

I0.02% / ºC, max

Transient response recovery time

25% load step change FL to 1/2 FL I1% error band

Single 200uS

Dual 200uS

Over load protection % of FL at nominal input 170% typ Short circuit protection Continuous, automatics recovery

INPUT SPECIFICA TIONS

Input voltage range

FDC05

FDC05-W

12V nominal input 24V nominal input 48V nominal input 24V nominal input 48V nominal input

9 – 18VDC 18 – 36VDC 36 – 75VDC

9 – 36VDC 18 – 75VDC

Input filter Pi type Input surge voltage

100mS max

12V input 24V input 48V input

36VDC 50VDC

100VDC

Input reflected ripple (Note 2) Nominal Vin and full load 20mAp-p Start up time Nominal Vin and constant resistor load 600mS typ

Remote ON/OFF (Note 3) (Positive logic)

(Negative logic) Remote off input current

DC-DC ON DC-DC OFF DC-DC ON DC-DC OFF Nominal Vin

Open or 3.5V < Vr < 12V

Short or 0V < Vr < 1.2V Short or 0V < Vr < 1.2V

Open or 3.5V < Vr < 12V

2.5mA

GENERAL SPECIFICATIONS

Efficiency See table Isolation Voltage Input to Output to Case 1600VDC, min Isolation resistance

ohms, min

Isolation capacitance 300pF, ma

Switching frequency

Standard “W” series

300KHz, typ 200KHz, typ

Approvals and standard IEC60950, UL1950, EN60950 Case material Nickel-coated coppe

Base material Non-conducted black plastic Potting material Epoxy (UL94-V0)

Dimensions

2.00 X 1.00 X 0.40 Inch (50.8 X 25.4 X 10.2 mm)

Weight 27g (0.95oz) MTBF (Note 4) 3.145 x 106 hrs

ENVIRONMENTAL SPECIFICATIONS

Operating temperature range (Reference derating curve)

Standard M1 (Note 5) M2 (W series)

-25ºC ~ +85ºC (with derating)

-40ºC ~ +85ºC (non-derating)

-40ºC ~ +85ºC (with derating)

Maximum case temperature +100ºC Storage temperature range -55ºC ~ +105ºC

Thermal impedance (Note 6)

Nature convection Nature convection with heat-sink

12ºC

watt

10ºC

watt

Thermal shock MIL-STD-810D Vibration 10~55Hz, 2G, 30minutes along X,Y and Z Relative humidity 5% to 95% RH

EMC CHARACTER IS TI CS

Conducted emissions EN55022 Level A Radiated emissions EN55022 Level A ESD EN61000-4-2 Perf. Criteria

Radiated immunity EN61000-4-3 Perf. Criteria

Fast transient EN61000-4-4 Perf. Criteria

Surge EN61000-4-5 Perf. Criteria

Conducted immunity EN61000-4-6 Perf. Criteria

The FDC05 and FDC05-W series offer 5 watts of output power from a 2 x 1 x 0.4 inch package without derating to 71ºC ambient temperature. FDC05 series have 2:1 wide input voltage of 9-18, 18-36 and 36-75VDC. FDC05-W series have 4:1 ultra wide input voltage of 9-36 and 18-75VDC. The FDC05 and FDC05-W features 1600VDC of isolation, short-circuit protection, as well as six sided shielding. The safety approve with EN60950 and UL1950. All models are particularly suited to telecommunications, industrial, mobile telecom and test equipment applications. According the extended operation temperature range, there are “M1” and “M2” version for special application.

TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherw ise noted

UL E193009 TUV R3-50007936 CB JPTUV-003641 CE MARK

• 5 WATTS OUTPUT POWER

• 2:1 AND 4:1 WIDE INPUT VOLTA GE RANGE

• INTERNATIONAL SAFETY STANDARD APPROVAL

• SIX-SIDED CONTINUOUS SHIELD

• HIGH EFFICIENCY UP TO 83%

• STANDARD 2” X 1” X 0.4” PACKAGE

• FIXED SWITCHING FREQUENCY

Page 2

Model

Number

Input

Range

Output

Voltage

Output

Current

Input

Current

(7)

Eff

(8)

(%)

Capacitor

Load max

(9)

FDC05-12S33 9 – 18 VDC 3.3 VDC 1000mA

387mA

75 3700uF

FDC05-12S05 9 – 18 VDC 5 VDC 1000mA

556mA

79 1700uF FDC05-12S12 9 – 18 VDC 12 VDC 470mA 610mA 81 290uF FDC05-12S15 9 – 18 VDC 15 VDC 400mA 658mA 80 188uF FDC05-12D05 9 – 18 VDC ± 5 VDC ± 500mA 595mA 74 ± 850uF FDC05-12D12 9 – 18 VDC ± 12 VDC ± 230mA 597mA 81 ± 140uF FDC05-12D15 9 – 18 VDC ± 15 VDC ± 190mA 609mA 82 ± 47uF

FDC05-24S33 (W) 18 – 36 (9 – 36) VDC 3.3 VDC 1000mA 199 (196mA) 73 (74) 3700uF FDC05-24S05 (W) 18 – 36 (9 – 36) VDC 5 VDC 1000mA 282 (274mA) 78 (80) 1700uF FDC05-24S12 (W) 18 – 36 (9 – 36) VDC 12 VDC 470mA 305 (301mA) 81 (82) 290uF

FDC05-24S15 (W) 18 – 36 (9 – 36) VDC 15 VDC 400mA 325 (325mA) 81 (81) 188uF FDC05-24D05 (W) 18 – 36 (9 – 36) VDC ± 5 VDC ± 500mA 289 (289mA) 76 (76) ± 850uF FDC05-24D12 (W) 18 – 36 (9 – 36) VDC ± 12 VDC ± 230mA 295 (295mA) 82 (82) ± 140uF FDC05-24D15 (W) 18 – 36 (9 – 36) VDC ± 15 VDC ± 190mA 308 (301mA) 81 (83) ± 47uF FDC05-48S33 (W) 36 – 75 (18 – 75) VDC 3.3 VDC 1000mA 100 (100m A ) 73 (73) 3700uF FDC05-48S05 (W) 36 – 75 (18 – 75) VDC 5 VDC 1000mA 145 (149mA) 76 (74) 1700uF FDC05-48S12 (W) 36 – 75 (18 – 75) VDC 12 VDC 470mA 151 (151mA) 82 (82) 290uF FDC05-48S15 (W) 36 – 75 (18 – 75) VDC 15 VDC 400mA 160 (163mA) 82 (81) 188uF FDC05-48D05 (W) 36 – 75 (18 – 75) VDC ± 5 VDC ± 500mA 149 (149mA) 74 (74) ± 850uF FDC05-48D12 (W) 36 – 75 (18 – 75) VDC ± 12 VDC ± 230mA 149 (149mA) 81 (81) ± 140uF FDC05-48D15 (W) 36 – 75 (18 – 75) VDC ± 15 VDC ± 190mA 154 (154mA) 81 (81) ± 47uF

PIN CONNECTION

SINGLE

DUAL OUTPUT

1 + INPUT + INPUT 2 - INPUT - INPUT 3 + OUTPUT + OUTPUT 4 NO PIN

COMMON 5 - OUTPUT - OUTPUT 6 CTRL (Option) CTRL (Option)

1. All dimensions in Inches (mm)

2. Pin Pitch tolerance I0.014(0.35)

2.00(50.8)

0.40 (10.2)

0.50 (12.7)

1.00(25.4)

0.10(2.5)

0.20(5.1)

0.80(20.3) 0.60(15.2)

0.22(5.6)

0.40 (10.2)

DIA. 0.04(1. 0)

1 2

34 5

Bottom

iew

Note

1. The FDC05 (W) series required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification

2. Simulated source impedance of 12uH. 12uH inductor on series with + Vin.

3. The ON/OFF control is option function. There are positive logic and negative logic. The pin voltage is referenced to negative input To order positive logic ON-OFF control add the suffix-P (Ex: FDC05-24S05-P) To order negative logic ON-OFF control add the suffix-N (Ex: FDC05-24S05-N)

4. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC.

(Ground fixed and controlled environment)

5. M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than standard and M2 version.

6. Heat sink is optional and P/N: 7G-0020A.

7. Maximum value at nominal input voltage and full load of standard type.

8. Typical value at nominal input voltage and full load.

9. Test by minimum Vin and constant resistor load.

0.4 0.6 0.8 1.00.05 0.2

OUTPUT LOAD (A

)

EFFICIENCY (%)

FDC05-48S05 Efficiency VS Output load

82 81 80 79 78 77 76 75 70

50 60 70 80 90

100 -40 -25 0 -10

100

AMBIENT T EMPERATURE (ºC )

OUTPUT POWER (% )

FDC05-48S05 Derating Curve

Nature convection

50 60 70 80 90

100-40 -25 0-10

100

AMBIENT TEMPERATUR E (ºC)

OUTPUT POWER (%)

FDC05-48S05-M1 Derating Curve

Nature convection

50 60 70 80 90

100 -40 -25 0 -10

100

MBIENT TEMPERATURE (ºC)

OUTPUT POWER

(%)

FDC05-48S05 Derating Curve Wi

h HEAT-SINK (N

ote5)

Nature convection