Page 1
D-FJ211
SERVICE MANUAL
Ver 1.2 2003.05
SPECIFICATIONS
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output is the value measured at a
distance of 200 mm from the objective lens surface on the optical pick-up
block with 7 mm aperture.)
Frequency range (European models)
FM: 87.5 - 108.0 MHz
AM: 531 - 1602 kHz
Frequency range (10k/9k switch)
• Canadian, C&SA, Mexican models:
9 kHz step:
FM: 87.5 - 108.0 MHz
AM: 531 - 1 710 kHz
10 kHz step:
FM: 87.5 - 108.0 MHz
AM: 530 - 1 710 kHz
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Model Name Using Similar Mechanism D-EJ360
CD Mechanism Type CDM-3325ER
Optical Pick-up Type DAX-25E
Power requirements
For the area code of the model you purchased, check the upper left side of
the bar code on the package.
•Two LR6 (size AA) batteries: 1.5 V x 2 DC
• AC power adaptor (DC IN 4.5 V jack):
Canadian, C&SA, Mexican models: 120 V, 60 Hz
AEP, EE, E13, 2E13 models: 220 - 230 V, 50/60 Hz
Australian model: 240V, 50Hz
Dimensions (w/h/d) (without projecting parts and controls)
Approx. 136 x 26 x 150 mm (5 3⁄8 x 1 1⁄16 x 6 in.)
Mass (excluding accessories)
Approx. 205 g (7.3 oz)
Operating temperature
5°C - 35°C (41°F - 95°F)
Design and specifications are subject to change without notice.
Supplied Accessories
9-877-103-03
2003E02-1
© 2003.05
AC power adaptor (1)
Headphones/earphones (1)
FM/AM PORTABLE CD PLAYER
Sony Corporation
Personal Audio Company
Pubulished by Sony Engineering Corporation
Page 2
D-FJ211
DANGER
Invisible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
lead-free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed
with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder
may also be added to ordinary solder.
TABLE OF CONTENTS
Specifications ............................................................................ 1
1. SERVICING NOTES................................................... 3
2. GENERAL
Locating the Controls ......................................................... 3
3. DISASSEMBLY
3-1. Upper Lid ASSY, Cabinet (Upper) Sub ASSY ........... 4
3-2. MD ASSY, Main Board .............................................. 5
3-3. “Motor ASSY (Sled) (M902)”,
Optical Pick-up (DAX-25E),
“Motor ASSY, Turn Table (Spindle) (M901)” ............ 5
4. ELECTRICAL ADJUSTMENS ............................... 6
5. DIAGRAMS
5-1. Block Diagram –CD SECTION– .............................. 9
5-2. Block Diagram –Tuner SECTION– ........................ 10
5-3. Printed Wiring Boards –Side A– .............................. 11
Printed Wiring Boards –Side B– .............................. 12
5-4. Schematic Diagram –MAIN SECTION (1/4)– ....... 13
5-5. Schematic Diagram –MAIN SECTION (2/4)– ....... 14
5-6. Schematic Diagram –MAIN SECTION (3/4)– ....... 15
5-7. Schematic Diagram –MAIN SECTION (4/4)– ....... 16
5-8. IC Pin Function Description ..................................... 20
6. EXPLODED VIEWS
6-1. Cabinet Section ......................................................... 22
6-2. Optical pick-up Section (CDM-3325ER) ................. 23
7. ELECTRICAL PARTS LIST ................................... 24
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS
PUBLIÉS PAR SONY.
2
Page 3
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR
BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the charged
electrostatic load, etc. on clothing and the human body. During repair,
pay attention to electrostatic breakdown and also use the procedure in
the printed matter which is included in the repair parts.
The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the
disc reflective surface by the objective lens in the optical pick-up block.
Therefore, when checking the laser diode emission, observe from more
than 30cm away from the objective lens.
Before Replacing the Optical pick-up Block
Please be sure to check thoroughly the parameters as per the “Optical
pick-up Block Checking Procedure” (Part No. : 9-960-027-11) issued
separately before replacing the optical Pick-up block.
Note and specifications required to check are given below.
• FOK output : IC601 yg pin
When checking FOK, remove the lead wire to disc motor.
• RF signal P-to-P value : 0.45 to 0.75Vp-p
D-FJ211
Laser Diode Checking Methods
During normal operation of the equipment, emission of the laser diode
is prohibited unless the upper panel is closed while turning ON the S809
(push switch type).
The following two checking methods for the laser diode are operable.
Method :
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S809 as shown in Fig. 1 .
3. Check the object lens for confirming normal emission of the laser
diode. If not emitting, there is a trouble in the automatic power
control circuit or the optical pick-up. During normal operation, the
laser diode is turned ON about 2.5 seconds for focus searching.
S809
LOCATING THE CONTROLS
CD player (front)
i (headphones) jack
SOUN/AVLS
P MODE/ F
VOL +*/–
*The button has a tactile dot.
OPEN
SECTION 2
GENERAL
Fig.1 Method to push S809
This section is extracted from
instruction manual.
Strap holes
DC IN 4.5 V
(external power
input) jack
.>
u*
x
• RADIO OFF
Display
RADIO ON/BAND • MEMORY
HOLD
CD player (inside)
G-PROTECTIO
Battery Compartment
3
Page 4
D-FJ211
z
The equipment can be removed using the following procedure.
SECTION 3
DISASSEMBLY
MD ASSY “Motor ASSY (Sled) (M902)”, Optical pick-up (DAX-25E),
Set
Upper lid ASSY,
Cabinet (upper) sub ASSY
Main board
Note : Follow the disassembly procedure in the numerical order given.
3-1. UPPER LID ASSY, CABINET (UPPER) SUB ASSY
5
Upper lid Assy
7
Ten screws (B2)
4
2
1
Open
3
“Motor ASSY, turn table (spindle) (M901)”
• CAUTION DURING ASSEMBLY
1
Spring (L)
2
Spring (R)
6
0
Cabinet
(upper) sub ASSY
9
8
Four craws
5
6
Spring (L)
4
1
3
Spring (R)
2
4
Page 5
3-2. MD ASSY, MAIN BOARD
)
7
MAIN board
1
CN601
5
MD ASSY
4
2
Connector (CN401)
3
Connector (CN402
D-FJ211
6
Cabinet (lower) sub ASSY
3-3. “MOTOR ASSY (SLED) (M902)”, OPTICAL PICK-UP (DAX-25E), “MOTOR ASSY, TURN TABLE (SPINDLE) (M901)”
1 Three screws
(B1.7x4)
2
3 Cover, Gear
8 Three screws
(B1.7x4)
6
0 Motor ASSY, Turn table
(Spindle) (M901)
5 Motor ASSY
(Sled) (M902)
9
7 Optical pick-up
(DAX-25E)
4
Chassis
5
Page 6
D-FJ211
R73
R73
r
TUNER SECTION
AM section
BAND : AM
AM RF signal
generator
30% amplitude modulation by 400Hz
signal.
Output level : as low as possible
FM section
BAND :FM
TJ3
(FM RF IN)
[MAIN BOARD]
(Side A)
TJ304
102
J606
06
TJ307
VDR305
TJ605
TJ801
VDR302
TJ802
TJ410
C325
TJ608
R601
AA
D306
(FM RF IN)
D
TJ3
TJ611
0.01µF
TAP1
TJ5
L606
ELECTRICAL ADJUSTMENTS
0 dB = 1µV
Put the lead-wire
antenna close to
the set.
FM RF signal
generator
33.75kHz frequency deviation
by 1kHz signal.
Output level :
as low as possible
C810
L4
D3
FJ120
R2
C22
FL2
C9
1
C44
TJ10
R873
C21
D2
R4
C8
TJ6
30
IC1
TJ8
L2
SECTION 4
L3
R844
R815
R75
TJ1
R66
C109
R74
R65
2
3
7
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
< > : 9kHz step
AM FREQUENCY COVERAGE ADJUSTMENT
Adjust parts Frequency display
L5 530kHz <531kHz>
Reading on digtal
voltmeter
Adjustment value : 0.7V
Standard value : 0.2–1.4V
Adjustment value : 5.0V
Confirmation 1,710kHz <1,602kHz>
Standard value : 4.3–5.7V
<4.4V>
<3.7–5.2V>
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1 620kHz <621kHz>
CT1 1,400kHz <1,395kHz>
FM FREQUENCY COVERAGE ADJUSTMENT
Frequency display Reading on digtal voltmeter
Confirmation 87.5MHz Standard value : 4.3–5.7V
L2 108MHz
Adjustment value : 9.5V
Standard value : 9.0–10.0V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L4 87.5MHz
Confirmation 108MHz
Adjustment Location : Main board
Frequency Coverage Adjustment
Setting :
level meter
16
Ω
[MAIN BOARD]
(Side A)
digital voltmete
(DC range)
set
TJ1 (VT)
TJ304
phones jack (J301)
102
J606
06
6
TJ307
VDR305
TJ605
TJ801
VDR302
TJ802
TJ410
AA
D306
C325
TJ608
R601
D
TJ3
(FM RF IN)
TJ611
TAP1
TJ5
L606
FL2
TJ10
C810
D3
R2
TJ6
(TU GND)
1
C44
L4
FJ120
C22
C9
IC1
TJ6 (TU GND)
R873
C21
D2
L3
R4
C8
TJ1
(VT)
30
TJ8
2
L2
R844
R815
R75
R66
C109
R74
R65
3
7
Page 7
Adjustment Location :
[MAIN BOARD] (SIDE B)
D-FJ211
L4 : FM Traking Adjustment
L2 : FM Frequency Coverage Adjustment
L1 : AM Tracking Adjustment
L5 : AM Frequency Coverage Adjustment
CT1 : AM Tracking Adjustment
7
Page 8
D-FJ211
p
B
3
CD SECTION
The CD section adjustments are done automatically in this set.
Precautions for Check
1. Perform check in the order given.
2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise
indicated.
3. Power supply voltage requirement : DC4.5 V in DC IN jack.
(J401)
VOLUME button : Minimum
HOLD switch : OFF
RF Level Check
Condition:
• Hold the set in horizontal state.
Connection:
oscilloscope
(AC range)
TJ601(RF)
[MAIN BOARD]
(Side A)
TJ303
C624
C619
R616
L602
601
C633
R615
IC601
C632
R614
C618
F
FB301
TJ305
FB101
R306
26
25
R613
C609
C608 C607
R612
C614
C613
C605
TJ601
(RF)
C604
C612
5
TJ401(A GND)
C325
VDR305
VDR302
TJ307
TJ605
TJ801
TJ802
TJ410
(A GND)
TJ608
TJ606
C606
AA
D306
R601
D
TJ611
TAP1
TJ3
TJ5
L606
C810
D
R2
C9
FL2
1
C44
TJ10
Procedure:
1. Connect the oscilloscope to the test point TJ601(RF) on the
MAIN board.
2. Set a disc. (YEDS-18)
3. Press the u button.
4. Check the oscilloscope waveform is as shown below.
A good eye pattern means that the diamond shape (◊) in the center of the waveform can be clearly distinguished.
RF Signal reference Waveform (Eye Pattern)
VOLT/DIV : 100 mV (With the 10 : 1 probe in use)
TIME/DIV : 500ns
RF level
0.45 to 0.75 Vp-
To watch the eye pattern, set the oscilloscope to AC range and
increase the vertical sensitivity of the oscilloscope for easy
watch-ing.
5. Stop revolving of the disc motor by pressing the x button.
8
Page 9
5-1. BLOCK DIAGRAM –CD SECTION–
SECTION 5
DIAGRAMS
IC603
D-FJ211
D-RAM(4M)
OPTICAL
PICK-UP
BLOCK
(DAX-25E)
OP IC
FOCUS
COIL
TRACKING
COIL
M902
SLED
MOTOR
M901
SPINDLE
MOTOR
VCC
RF
OP_G-SW
OP_STB
A
A
E
F
LD
PD
M
M
VCC1_2.2V
LD
DRIVER
Q601
VCC1_2.2V
F+
F-
T+
T-
S+
S-
W
V
U
+VBAT
L403
13
88
44
42
48
46
52
50
80
53
49
45
41
RFI
A
9
B
8
E
6
F
7
RFDC
LD-SW
2
6
4
2
1
APC
FO3
RO3
BRIDGE
FO2
RO2
BRIDGE
FO1
RO1
BRIDGE
W_O
V_O
U_O
BRIDGE
COMCOM
VM1
VM12
VM23
VM3
SPVCC
FOCUS/TRACKING COIL DRIVE
SLED/SPINDLE MOTOR DRIVE
16 17
RFGO
RF
AMP
A/D
PD
3
CH3
H
CH2
H
CH1
H
CH4
H
IC403 (1/2)
DETI
DEMODULATOR
I/F
D0-3 A0-9
2,3,24,25 9-12,14-18,5
87,88,84,85 97-100,96-91,82
D0-D3
EFM
SERVO
PWM
FDOP
FDON
TDOP
TDON
SDOP
TIN+
60
59
56
55
58
57
70
72
34
74
40
39
38
37
35
36
TIN-
SIN+
FIN+
FINSIN+
SIN-
TIN+
TIN-
CPOL
SLVOP
SYNC
SDON
SIN-
75 74 77 76 79 78 72 73 71 504947533738
FIN-
FIN+
FIN3
RIN3
LEVEL
LEVEL
POWER_LT_I
FIN1
RIN1
FIN2
RIN2
BBK
PWM
SYNC
XSDTO
XCSK
WAKEUP
H_RESET
XRST_I
FG
SHIFTER
SHIFTER
A0-A10
SUB CODE
PROCESSOR
CLVON
CLVOP
CLKDRV
CPOL
SYNC
CLVOP
DEFFERENTIAL
Q407
XRAS
XCAS
4 23 3
90 83 89
XCAS
XRAS
CLOCK
OSC
X_O
X601
16.934MHz
XWE
XWE
X_I
WARK-UP
DETECT
Q801,802
IC601
RF AMP,SERVO
DIGITAL SIGNAL PROCESSOR
D-RAM CONTROLLER
D/A CONVERTER
SIO
CLK4M
SCLK_I
SDTO_I
SDTI_O
D802
SRW_I
48
15
SRW_O
X_I
2
OP_G-SW_O
79
XOPSTBY_O
78
WP/KEY2_RM_I
33
FG_I
72
XPOWLT_O
14
SDTI_I
16
SDTO_O
17
SCK_O
18
XWAKEUP_O
66
8
XREST_I
XRST_O
76
VCPU_2.0V
P-OFF_I
SCOR
XBUSY_O
SCOR_I
XBUSY_I
POWER-OFF_O
TO
TUNER
SECTION
(Page 10)
DAC
DEFDCT_O
GFS_O
FOK_O
657064524345
6711371177
GFS_I
FOK_I
DEFECT_I
WP/AD_KEY1
AD_KEY_2
2523 28 40
KEY MATRIX
S801 S805
| |
S804 S808
C
LDACO
RDACO
DVDDIO
AVDD2 2.25V
DVDDV 1.5V
TIST
TEST
CLK4M_2
RESET2
TEST
IC801(2/2)
SYSTEM
CONTROL
MICON
TU_L
TU_R
31
29
36
80
86
34
40
51
5
VCHK
PGM_SDTO
PGM_SDTI
68674
PGM_SDTI_I
PGM_SDTO_O
VCC2_2.0V
VCC1_2.2V
VCPU_1.5V
PGM_SCK
PGM_SC_SEL
7369
PGM_SCK_O
PGM_SC_SEL
WP/XOPEN_I
S809
(OPEN)
33
35
CD_L-I
32
CD_I_R
36
31
12
HOLD
OFF ON
STB_HPSW_I
26
HPSW_O
WP/AD_RMKEY
HOLD_I
S810
.
IC301
PRE EQ AMP/EVR/
HADPHONE AMP
AD_CHGMNT
TUNER_ON_I
AD_BATTMNT
AD_DCINMNT
GPROSW
AVCPU
38
19
S811
G.PROTECTION
OFF ON
4
VCC2
17
VCC1
44
IN SEL
POWER-L_O
CENTER-AMP
POWER-R_O
BASS-H/L-SW TU_BASS2
MUTE-SW_I
22
34
+V BAT
24
27
ADVREF
20
VCPU_2.0V
BASS-SW
VOL-CTL_I
BEEP_I
VCC2_2.0V
7
6
5
25
26
14
3
1
VCC1_2.2V
VCPU_2.0V
Q401
CHARGE
SWITCH
XTU_BASS1
PWM
BEEP
AMUTE
+VBAT
VCC2_2.0V
A
IC403 (2/2)
POWER CONTROL
VMMNT
66
VCC2
18
17
VCC1
19
VCPU 2.0V
CHGMNT
67
DCIN
61
REGB
62
DET
63
65
CHGB
+VBAT
SWITCH
Q402, 403
BATT_MNT
TU_ON
PGM_SC_SEL
OPEN_DTS
HOLD
AD_KYE2
AD_KYE1
SDTO
SCK
TO
TUNER
SECTION
(Page 10)
D405
D402
SEM
SEO
GSW
VCC
VCC0
STNG
VIN
BATM1
BATM2
DCIN_S
TO
D
TUNER
SECTION
(Page 10)
J301
ANT
i
VCPU_1.5V
23
22
21
20
16
25
L404
LG
8
12
68
69
64
L401
L402
TO
TUNER
B
SECTION
(Page 10)
Q406
L410
Q405
D408
Q408
Q404
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION LR6)
2PCS, 3V
J401
DC IN 4.5V
!
• SIGNAL PATH
: FM
: CD PLAY
99
Page 10
D-FJ211
Ver 1.1 2003.03
5-2. BLOCK DIAGRAM –TUNER SECTION–
TO
CD
SECTION
(Page 9)
D
L4
FM
TRACKING
L2
FM/TV
FREQUENCY
COVERAGE
L1, CT1
AM
TRACKING
L5
AM
FREQUENCY
COVERAGE
ANT
(FM/TV OSC)
L4
(FM RF)
L2
FERRITE-ROD
ANTENNA
L5
(AM OSC)
AM
2E13,C&SA,CND,MX
Q4
TV/FM/AM FRONTEND, FM MPX
FM-RF
2
FM-RF_O
29
D3
CT1
TU-VCC
D4
(VT)
LPF
Q12,13
L1
FM/TV-OSC
24
1/2
AM_BP
28
AM-RF_I
27
AM-OSC
25
D6
2E13,C&SA,CND,AUS,E13,MX
S1
STEP
10K
R
9K
TV
OSC
FM
OSC
AM
MIX
AM
OSC
T1
VCPU_2.0V
IC1
FM/TV
MIX
CONVERTOR
FM-MIX_O
BUFF
1/8
or
1/16
AM-MIX_O
BUFF BUFF
B+ SWITCH
DC-DC
Q14
Q10,11
CF2
4
TU-VCC
CF3
5
TU-VCC
+VBAT
FM-IF_I DET_O
8
FM-IF
AM-IF_I
10
AM-IF
FM
DET
IF BUFF
AM
DEF
OSC_O
23
BUFFER
12 13
SW
IF-COUNT_O
REQ-SW
2019
Q15
Q7
MPX_I
FM
MPX
MODE1 Q2
PW SW
FM/TV/AM
MODE2
L_O
R_O
LPF2A
LPF2B
LPF1
16
15
17
18
14
21
Q3
22
TU_L
TU_R
C
TO
CD
SECTION
(Page 9)
IC2
+1.6V REG.
VOUT VIN
1 3
B+ SWITCH
Q5,9
+VBAT
VCPU_2.0V
RF-VCC
45
26
TU-VCC
AD-DC_REF
Q8
IC4
EEPROM
CS
SK
D1
D0
CF5
(75KHz)
1 32
2
3
4
74
X_O
X_I
75
EEP-CS_O
31
EEP-SK_O
30
EEP DO/DI_IO
COM1-4 S1-17
1-4 5-20,25
65 21 71 64 61 52 59 55
IF_I
EO(D01)_O
AM-STEP_I
TV/FM/AM_I
IC3
TUNER CONTROL
LCD-REQ_I
XL/O-I
CD-ON_I
RESET-TU_I
SDU-SDO_O
ACK-CD_O
28 33 39 73 47 54
LCD1
LIQUID
CRYSTAL
DISPLAY
IC801(1/2)
SYSTEM
CONTROL
MICON
39 37 70 75 10 9
XL_O
CD_ON_O
LCD-REQ_O
SDTI_I_TU
RESET-TU_O
ACK_CD_I
10
29
AMUTE_O
BEEP_O
TUNER_POWER_O
10
D301
74 62
38
D302
IF-REQ_O
BAND-CTL2_O
49
TU-HOLD_I
XLID-OPEN_I
CDU-SCK_I
BAND-CTL1_O
MONO/LOCAL-CTL_O
PLAY-KEY-CLT_O
AD-KEY2_I
AD-KEY1_I
TU-BASS_O
XTU-BASS_O
TU_MUTE_O
VOL_PWM_O
TU_BEEP_O
CDU-SDI_I
BATT_I
TU-ON_O
SC-SEL_I
51
29
48
46
43
26
36
34
38
37
56
58
50
• Abbreviation
HOLD
OPEN_DTS
SCK
SDTO
BATT_MNT
AD-KEY1
AD-KEY2
TU_ON
PGM_SC_SEL
TU-BASS2
XTU-BASS1
PWM
BEEP
AMUTE
CND : Canadian
B
A
TO
CD
SECTION
(Page 9)
TO
CD
SECTION
(Page 9)
• SIGNAL PATH
: FM
: AM
C&SA : Central and South America
MX : Mexican
AUS : Australian
E13 : AM frequency range 531-1,602kHz
2E13 : AM frequency range 531-1,710kHz
Page 11
D-FJ211
Ver 1.2 2003.05
5-3. PRINTED WIRING BOARDS –SIDE A– • Refer to page 17 for Notes.
C101
TJ18
TJ19
C201
C324
R102
R201
R103
R202
C102
34
23
22
C308
C309
AEP,UK,C&SA,
CND,EE,MX
R304
R820
TAP800
R101
33
C104
R106
R104
C103
L605
TP807
2
C305
C304
R105
C307
C306
CN801
R300
R630
C629
R631
R626
1
10
R629
R624
TP637
C303
TJ303
L603
C620
R617
C627
R627
2E13,AUS,E13
C624
R616
X601
R615
C633
C619
L602
C632
R614
C618
26
25
L604
C626
R618
R620
R619
50
51
IC601
R446
C605
1
TP610
100
C631
C600
R600
R447
TJ406
1
R859
TP639
75
76
26
C621
IC603
13
R606
C623
C622
TJ803
R858
R854
TAP804
TJ806
R843
FOR
CHECK
2E13,AUS,E13
TAP807
TP833
1
R852
R849
20
C806
R804
R845
R807
Q802
E
R837
R846
21
D804
14
80
IC801
R827
R830
R836
C801
D805
C809
R808
C802
R832
Q801
E
A
B
C
FERRITE-BAR
ANTENNA
D
L1
AM
1
MAIN BOARD
(SIDE A)
C205
C318
R311
C105
44
C317
C328
1
11
12
C315
C312
C311
C321
JC
C313
R301
C300
C20
C13
C6
C14
R6
TJ4
C11
R7
C19
C18
2E13,AUS,E13
TJ302
IC301
R3
C204
R206
R203
R205
C202
R204
C203
C310
R310
R8
L5
C2
C7
E
: USES UNLEADED SOLDER.
3 4 5 6 7
S802
SOUND/AVLS
FB201
R610
C610
R608
61
40
C614
TJ607
R813
FB301
FB101
R613
C608 C607
R612
TJ601
R605
TJ602
R611
E
R825
60
41
R802
R811
R817
(SIDE B )
TJ202
TJ305
C609
C613
C612
R602
L601
Q601
TJ603
R812
R805
MAIN
BOARD
TJ304 TJ102
C604
C606
R604
R603
C55
TP811
TP834
TP26
C804
C803
A
TJ606
TJ604
TP22
TJ307
TJ609
TJ618
Q10
TJ411
J301
i
TJ304
AA
D306
C325
D
TAP1
TJ3
TJ605
TJ802
TJ5
TJ410
L606
TJ608
TJ801
TJ611
R601
TJ614
R25
C1
FB402
TJ402
DRY BATTERY
(IEC DESIGNATION LR6)
2E13,AUS,E13
FL2
TJ10
CF2
TJ613
SIZE "AA"
2PCS, 3V
C810
C44
CF3
G-PROTECTION
L409
TJ612
D3
R2
15
C36
Q7
E
R18
S811
OFF
t
ON
FB405
B C E
C9
1
Q402
C22
C39
L4
TJ6
C42
2E13,C&SA,
CND,MX
CF4
TJ401
2E13,AUS,E13
C405
L405
J401
DC IN 3V
TJ403
P MODE/
C&SA,CND,MX
IC1
R12
TJ9
C31
R29
2E13,AUS,E13
TJ418
R433
TJ404
TJ405
C426
2E13,AUS,E13
C402
1-685-956-
R45
C408
16
L406
R873
30
R28
C60
C71
R46
S801
C435
TJ8
L2
TJ8
C32
R11
R27
C81
VDR402
L401
R38
C75
C78
TP25
VDR401
R10
Q8
C&SA,CND,MX
R40
TAP2
TP20
R85
TJ7
C434
E
Q403
R416
D402
(21)
21
C12
41
60
R449
C10
C30
E
C438
R420
C404
S804
VOL+
R844
TJ1
C23
C27
R1
D4
TP36
C85
AEP,UK,EE
R43
R41
TP40
TP417
TJ407
C448
C447
R436
40
61
R408
E
R407
L402
R448
2E13,AUS,E13
C403
>
C&SA,CND,MX
C87
C100
R53
TP35
C97
C80
R50
R82
R57
R822
2E13,C&SA,
CND,AUS,E13,MX
C442
C400
R428
R438
C440
IC403
C418 C423
Q401
C419
C420
R403
R869
R809
S808
PRESET/TUNE+
S803
VOL-
R835R815
C&SA,CND,MX
TJ409
C96
C94
C93
L11
2E13,AUS,E13
AEP,UK,C&SA,CND,
EE,MX
R61
R56
R60
R55
R59
FB406
R421
R439
R431
R435
C439
R444
G
D
Q405
S
21
C450
20
100
C422
C421
R865
C&SA,CND,
MX
>
PRESET/TUNE–
JC
R810
R829
TP83
R823
R872
C808
TJ804
S809
(OPEN)
2E13,C&SA,
CND,AUS,E13,MX
EXCEPT
AUS,E13
FB408
C437
D408
R430
E
Q404
R432
R425
C433
C428
C&SA,CND,MX
1
L403
JC
S807
C429
S805
B
HOLD
C436
X
S810
R871
ON
t
OFF
2E13,AUS,E13
R874
C811
.
C425
R863
R864
R800
LCD1
S806
,RADIO OFF
x
S812
RADIO ON/
BAND • MEMORY
• Semiconductor
Location
Ref. No. Location
D3 A-4
D4 B-5
D306 A-4
D402 E-5
D408 D-5
D804 D-3
D805 D-3
IC1 B-4
IC301 B-2
IC403 D-5
IC601 B-3
IC603 C-2
IC801 C-3
Q7 B-4
Q8 B-5
Q10 C-3
Q401 E-5
Q402 D-4
Q403 E-5
Q404 D-5
Q405 D-5
Q601 C-3
Q801 D-3
Q802 D-2
11 11
Page 12
D-FJ211
Ver 1.2 2003.05
PRINTED WIRING BOARDS –SIDE B– • Refer to page 17 for Notes.
1
2
MAIN BOARD
A
B
C
D
E
(SIDE B)
TP805
5
IC4
C99
8
Q406
D
R423
L404
TP401
TP402
E
Q408
C95
1
20
R63
4
1
L410
D410
S
G
L407
TP403 TP404
C107
C38
C92
C89
R44
C88
C62
TP33
CF5
80 61
C82
IC3
21 40
C445
C427
Q407
R441
E
C441
R434
C432
CN402
R419
C443
TP420
D409
TP419
4
1
R414
R451
R452
TP4
TP9
TP3
C25
C47
E
Q3
E
Q2
C48
DS
Q12
G
R49
60
41
R80
2
1
CN401
TP418
R411
C417
C415
R412
C411
C406
R429
R33
R32
C59
Q13
R31
C58
R30
R39
E
Q15
R37
R42
C73
R440
R801
L411
R424
R422
FB403
R413
D406
TP406
C35
C50
C40
C49
C41
E
C76
R84
TP801
FB404
C410
D403
: USES UNLEADED SOLDER.
3 4 5 6
C316
TP620
TP615
TP820
TP2
TP8
R833
R841
C68
C67
C61
E
Q14
R35
C69
R36
TP24
C70
AEP,UK,C&SA,CND,EE,MX
TP632
TP631
TP629
TP630
TP627
TP628
TP829
TP1
A
A
D301
TP6
K
K
D302
A
A
TP824
TP825
TP634
C807
TP633
R302
R427
C800
CT1
D1
TP828TP818
D802
C805
L10
E
Q301
C110
C210
C314
R109
MAIN
BOARD
(SIDE A)
A
1-685-956-
(21)
TP16
D405
C53
R24
M902
SLED
MOTOR
M
M901
SPINDLE
MOTOR
M
TP7
R78
FB401
C33
1
R52
2E13,C&SA,
CND,MX
C43
E
Q4
15
CN601
C45
R19
L9
R23
R821
10k 9k
2E13,C&SA,
CND,AUS,E13,MX
R21
STEP
AEP,UK,C&SA,CND,EE,MX
C630
TP15
TP616
C625
R621
TP609
TP17
Q5
E
C46
R22
E
Q9
TP12
R831
TP21
R803
R814
AEP,UK,C&SA,CND,EE,MX
T1
C65
D7
C66
R34 C64
3
D6
Q11
E
IC2
12
S1
t
OPTICAL PICK-UP
BLOCK
DAX-25E
R209
R309
21
• Semiconductor
Location
Ref. No. Location
D1 D-5
D6 D-4
D7 D-4
D301 C-5
D302 C-5
D403 E-3
D405 D-3
D406 E-3
D409 D-2
D410 D-2
D802 D-5
IC2 D-4
IC3 C-2
IC4 C-2
Q2 B-3
Q3 B-3
Q4 A-3
Q5 C-4
Q9 C-3
Q11 D-4
Q12 B-2
Q13 B-3
Q14 D-4
Q15 C-2
Q301 C-6
Q406 D-2
Q407 D-2
Q408 D-2
12
12
Page 13
5-4. SCHEMATIC DIAGRAM – MAIN SECTION (1/4) – • Refer to page 17 for Notes.
D-FJ211
Ver 1.1 2003.03
902
M
TRACKING
COIL
901
M
FOCUS
COIL
POW
D GND UCOM
VCPU4 1.5V
DRY BATTERY
SIZE"AA"
(IEC DESIGNATION LR6)
2PCS,3V
2.2V
CLVOP
BUS-2
ER GND
AU GND
VCC1
J401
1
W
V
U
4
CN402
4P
CN401
2P
1
2
15
10
5
1
CN601
15P
1-2
RF
3V
R601
COM
W
V
U
47k
R440
R441
1000p
0.047
10k
C439
2200p
EXCEPT AUS,E13
C434
16V
FB405
0
100k
C443
C436
16V
47
RESET
XWAKE
1
R432
1k
47
C437
47
16V
EXCEPT AUS,E13
C427
0.01
R439
47k
FB406
OPGSW
R416
OPSTB
220
SIN-
TIN-
FIN-
SIN+
TIN+
L403
47
FIN+
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE MOTOR DRIVE,
W
V
U
µH
0.1
C429
C428
4.7
16V
R420
C419
C420
R801
R403
0
0
Q403
2SC4116GL
ITCH
SW
R407
1
2.2
C418
0.022
0.022
C421
C422
C423
NT
DC M
NT
100k
0.1
4700p
4700p
4700p
EXCEPT AUS,E13
R449
100k
C425
6.3V
22
R408
100
0
1
R411
220k
R451
100k
R412
47k
R452
100k
Q402
2SB1237TV2PQR
SWITCH
D405
MA2YD2300LSO
C415
0.22
C417
0.1
C406
2.2
COM
BATMNT
CHGMNT
CPOL
FG
R419
10k
R413
47k
BATT M
FB403
S+
S-
C405
1
D402
MA2H735
Q401
2SD1781K
CHARGE
ITCH
SW
UDZSTE-175.1B
C411
1
A2H735
M
VDR402
C404
1000p
L402
µH
4.7
D403
D406
R414
0
FB401
C410
A
TJ601
B
(RF)
LD
PD
E
F
F+
T-
T+
F-
0
FB404
0
R448
FB402
0
0
L405
C408
1000p
2E13,AUS,E13
VDR401
0
L401
µH
4.7
C403
1
C402
1000p
R422
0
POW
S-
S+
IC403
BH6580KV-F
ER CONTROL
µH
L404
220
R424
0
6.3V
220
C426
T+
R425
0
L406
T-
47µH
C433
F+
R429
0
L409
L407
µH
100
1
C432
220
6.3V
Q404
2SB167900LSO
ITCH
SW
R430
1k
F-
C435
22
47µH
6.3V
C450
D408
A111-TX
M
R431
100k
Q408
2SC4081T106
ITCH
SW
L411
47µH
C438
1
CPH3303-TL
SW
R428
100k
1
Q405
R433
100k
ITCH
C440
2200p
R435
10k
C447
C448
R438
C445
1
0
R436
R421
10k
M
L410
47
D409
A111-TX
Q407
2SC4081T106
DIFFARENTIAL
POW
0
R444
100k
µH
R423
0
ERLT
SDTO
SCK
AKE
XW
RESET
SYNC
C442
100
10V
C400
1
D410
MA2H735
Q406
CPH3403
ITCH
SW
FB408
0
C441
0.22
R434
100k
R427
47k
VCPU 2V
VCC2
A GND TU
VIN
B1-4
D GND
13 13
B1
D GND2
TU ON
Page 14
D-FJ211
Ver 1.2 2003.05
5-5. SCHEMATIC DIAGRAM – MAIN SECTION (2/4) – • Refer to page 17 for Notes.
R621
0
2E13,AUS,E13
R606
0
C621
0.1
2SB167900LSO
LD
L601
10µH
*8 C610
4.7
2.2
TINTIN+
SINSIN+
0.1
C625
XCAS
D2
D3
D0
D1
E
XW
XRAS
A9
A8
A7
A6
A5
A4
A0
A1
A2
A3
Q601
LD DRIVER
R608
2.2
2E13,AUS,E13
AEP,UK,C&SA,CND,EE,M
R611
470
R610
100k
C610
A3
A1
A2
GFS
CPOL
SYNC
FIN+
FIN-
100k
R602
PD
BATMNT
E
C631
0.1
*8
R447
0
X
R624
10k
DIGITAL SIGNAL PROCESSOR
D-RAM
100k
100k
100k
R603
R605
R604
F
A
B
C600
R600
2.2
47
6.3V
FOK
DEFECT
IC601
BU9354KV
P,SERVO,
RF AM
CONTROLLER
D/A CONVERTER
C612
0.01
C605
1000p
R629
C614
2200p
C613
0.01
XBUSY
R612
C607
CLK4M
R631
2.2k
L604
µH
10
0
C608
0.1
0.22
C604
0.1
C606
6.3V
16V
R613
470
C609
47p
C629
C626
0.1
R627
C633
0.1
C618
2.2
*1 R106,206
4.7k
*2 R105,205
1
R614
47
R630
R619
R620
R618
C627
10k
C619
R615
10p
0
R616
1M
L602
C104
1
C204
1
C630
100
6.3V
10k
AEP,UK,EE
2E13,C&SA,CND,AUS,E13,M
AEP,UK,EE
22k
10k
2E13,C&SA,CND,AUS,E13,M
HP SW
A M
BEEP
0
470
470
470
0.01
R617
C624
10p
X601
16.934MHz
0
R106
*1
R206
*1
C632
0.1
AEP,UK,C&SA,CND,EE,M
D301
A792W
M
UTE
D302
A792W
M
SDTI
SDTO
SRW
SCK
POFF
XRST
SCOR
0
R105
*2
R205
*2
2E13,AUS,E13
K
K
X
X
C620
0.1
L603
10
µH
R446
0
R304
0
TU M
TU BEEP
L605
C622
0
R626
0
PW
TU BASS2
XTU BASS1
X
UTE
C623
22
6.3V
M
AEP,UK,C&SA,CND,EE,M
2E13,AUS,E13
R102
R101
C101
1
R310
22k
C309
C305
0.047
10
6.3V
C305
1
C303
22
6.3V
C306
22
6.3V
C307
10
6.3V
C103
470p
C102
470p
*5 R103,203
2.2k
*6
*7
4.7k
R203
1
*5
R301
22k
C300
4.7
AEP,UK,C&SA,CND,EE,M
X
C308
1
R300
2.2k
C304
0.047
R104
2.2k
R103
*5
2E13,AUS,E13
AEP,UK,C&SA,CND,EE,M
C202
470p
C313
4.7
C310
22
6.3V
X
BASS NF
BASS H/L SW
BASS SW
BASS T
BIAS O
BIAS I
RIPPLE F
STB HPSW
PRE GND
X
R202
*6
R201
*7
C201
1
MIX O
I
TU I R
A5
A4
2E13,AUS,E13
C310
2.2
NC
AGC SW
BASS CTL
BASS O
CD L I
TU L I
CD I R
VREF
C203
470p
R204
2.2k
C324
0.01
A7
A6
NC
IC301
AN17882A-E1
PRE EQ AMP/EVR/
HEADPHONE AM
LINE L O
*6 R102,202
10k
22K
*7 R101,201
10k
0
A9
A0
A8
VCC1
LINE R O
C205
0
XRAS
XCAS
C311
22
6.3V
VOL BIAS
VOL BIAS
AVLS I
AVLS O
P
VOL L O
VOL R O
2.2
AEP,UK,EE
2E13,C&SA,CND,AUS,E13,M
AEP,UK,EE
2E13,C&SA,CND,AUS,E13,M
D1
XWE
D3
D2
VOL CTL I
IN SEL
D0
RIPPLE F
C AMP SW
ER GND
POW
ER L O
POW
CENTER AM
ER R O
POW
BEEP 1
M
UTE SW
M
C105
AVLS SW
VCC2
UTE T
2.2
X
X
C312
22
6.3V
C321
22
6.3V
P
I
R309
R109
0
C314
1000p
C110
1000p
C315
0.1
Q301
DTC143TUA
INV.
C317
0.1
2E13,AUS,E13
220
AEP,UK,C&SA,CND,EE,M
6.3V
FB101
0uH
FB201
C316
0
R209
0
C210
1000p
FB301
0uH
C318
0.22
R311
100k
R302
4.7
X
0uH
C325
0.01
D306
A3J14700LSO
M
BUS-2
CLVOP
VCPU4 1.5V
2.2V
RF
3V
VCC1
1-2
AU GND
D GND UCOM
POWER GND
A GND TU
B1
14
14
B 2-4
TU L
TU R
FM ANT
VCC2
Page 15
5-6. SCHEMATIC DIAGRAM – MAIN SECTION (3/4) – • Refer to page 17 for Notes. • Refer to page 20 for IC Pin Function Description.
D-FJ211
Ver 1.2 2003.05
VCC2
VCPU 2V
TU ON
D GND2
B 3-4
HOLD
LCD REQ
G-PRO
0
R805
XL
0
R811
TU ON
100k
R814
470
R817
T5AW6-Z7C
SYSTEM CONTROL
0
R820
XWAKE
PGM_SDTO
PGM_SDTI
OPEN DTS
BEEP
10k
R822
IC801
MICON
0
0
R831
R825
GFS
PGM_SCK
CD ON
TUPWR ON
DC MNT
OPEN
0
470
R830
R827
0
R812
FG
A MUTE
PGM_SEL
AD KEY1
470
470
R833
R832
0
R821
XRST
RESET TU
AD KEY2
BATMNT
470
0
R837
R836
POFF
OPSTB
CHGMNT
R841
100k
OPGSW
R845
10k
*1 R804
2.2k
TAP806
10k
AEP,UK,EE
2E13,C&SA,CND,AUS,E13,MX
R804
*1
OPEN:NORMAL MODE
SHORT:TEST MODE
MA2ZD14001S0
R849
R852
R854
C807
C800
0.1
D802
0.22
C805
C801
C809
C802
470
470
0
R858
R859
0.01
0.01
0.01
0.01
1k
1k
RESET
SCK
SDTO
SDTI
SRW
POWERLT
DEFECT
HP SW
SCOR
SDTI TU
ACK CD
RESET2
XBUSY
FOK
TEST
CLK4M
C806
0.1
R863
C&SA,CND,MX
C811
0.01
C808
4700p
S805
R864
2.2k
R800
22k
10k
R823
10k
R829
2.2k
R810
22k
C810
0.01
2E13,AUS,E13
2E13,AUS,E13
Q801
DTC143TUA
Q801,802
WAKE-UP
DETECT
OPEN
HOLD
C804
1000p
G-PRO
C803
1000p
,RADIO OFF
SOUND/AVLS
R871
220k
TAP805
R874
10k
S806
R865
2.2k
S802
R835
2.2k
R843
2.2M
R872
10k
S812
R813
100k
R807
2.2M
C&SA,CND,MX
S803
VOL-
R844
10k
R815
22k
R808
1M
D805
MA728-TX
D804
MA728-TX
R846
470k
Q802
2SC4116GL
S809
(OPEN)
OFF
S810
HOLD
ON
ON
G-PROTECTION
OFF
S807
,PRESET TUNING -
R809
10k
R869
22k
S804
VOL+
R873
22k
C&SA,CND,MX
S811
PGM SC SEL
S801
P MODE/
S808
,PRESET TUNING +
PGM_SEL
PGM_SCK
PGM_SDTI
PGM_SDTO
RESET2
TEST
CN801
10P
CHECK
HOLD
B1
100k
R803
AEP,UK,C&SA,CND,EE,MX
R802
0
15 15
Page 16
D-FJ211
Ver 1.2 2003.05
5-7. SCHEMATIC DIAGRAM – MAIN SECTION (4/4) – • Refer to page 17 for Notes.
p
2
C
100
7
0p
C
22
11
p
C
47
13
C
5p
7
R
70k
4
0
2
C
0.1
30
C
00p
10
6
D
34
R
111
A
1k
M
64
C
10p
66
C
2.2
N
,C
A
S
&
2E13,C
2SC
53
R
4.7k
F5
C
95
C
0.1
94
C
0.1
14
C
p
10
,M
D
Q
4154TP
W
S
96
C
0.47
5
L
8
R
10k
5
L
M
A
Y
C
EN
U
EQ
FR
E
G
A
ER
V
O
C
10
R
0
61
C
5p
T1
68
C
0.01
X
4
-1F
H
ITC
21
R
2.2k
43
C
0.01
(D
EO
LD
O
H
C
N
D
N
G
C
N
/FM
TV
D
D
V
ES
R
O
X
I
X
T
X
V
LC
V
1
C
2
C
EE
V
+B ON/OFF O
02)
I
M
/A
(1.8-2.2V
ET I
D
COM1
Q
C4154TP
2S
C
D
V
N
O
C
69
C
0.01
2E13,A
R
100k
XTU BASS1
XTU TEST I
XTU BASS O
BAND CTL1 0
I
)
TC
TU
COM3
COM2
COM4
LC
14
-1F
C
-D
R
TO
ER
36
R
220
EP
FL2
40
TU BASS2
TU BASS O
MONO/LOCAL CTR O
IC
9327A
C
ER
N
S1
S2
1
D
35
R
100k
,C
K
,U
ACK CD
ACK CD O
IF R
TU
TES
IF I
EO
3
F-Z7C
TR
N
O
S3
LIQ
1000p
,C
A
S
&
42
R
10k
HOLD
DCIN DET I
BAND CTL2 O
O
EQ
TE O
U
M
T
01) O
(D
TU
L
O
S5
S4
ID
U
79
C
p
1000
C
1000p
C
0.1
L10
µH
10
67
C
22
6.3V
70
C
X
,M
D
N
PWM
TU BEEP
TU HOLD I
VOL PWM O
T A
S7
S6
R
C
25
47
SCK
SDTI TU
CDU SCK I
TU BEEP O
L O
S
V
N
O
D
C
N
O
TU
EL I
S
C
S
M
A
S9
S8
L
TA
S
Y
78
C
1
SDTO
0
R84
CDU SDI I
CDU SDO O
I
I
I
TEP
S
S11
S10
IS
D
AD DC REF
LA
P
S12
LA
P
FER
A
C
1000p
T1
1,C
L
M
A
G
IN
K
C
A
TR
L1
M
A
R
A
ITE-B
R
A
N
TEN
N
58
C
0.22
880G
2SK
30
R
10k
59
31
R
4.7k
71
C
0.01
39
R
470
15
Q
-TX
3931-C
C
2S
FFER
U
B
C62
100p
6
C
2
0.02
T1
C
6
R
470
9
C1
22
.0
0
12
Q
-TE85L
R
F
LP
32
R
470
33
R
4.7k
75
C
0.01
37
R
100k
8
3
R
1k
82
C
.01
0
97
C
0.01
L11
µH
10
87
0.1
C
88
C
22p
89
C
5p
92
C
10p
D
152
V
K
k
87
R
0
RESET TU
R
85
C
22
6.3V
1
0-TL0
&
C
27
R
22k
28
R
0
M
2S
0.01
2E13,A
44
0
C
S
100k
C
100k
A
C
60
R
0
C
.0
0
,C
A
29
R
7
D
8130
1000p
Q
4154TP
LP
U
46
81
1
3
R
k
10
18
22
X
,M
D
N
65
C
0.01
33
C
13
-1F
F
TU MUTE
,E13
S
45
R
10k
49
R
0k
1
100
C
0.1
93
C
0.47
TV RF O
TV RF I
73
C
0.1
BATT MNT
HDC I
BATT I
A
A
EEP
LID
X
LC
K
Y
S13
S14
Y
FM RF O
FM RF I
RM KEY I
K
D
K
D
EEP
EEP
O
D
O
D
C
EY
ES
D
ES
D
ES
D
S15
TV L ON O
EY
N
EY
L/O
X
S
C
K
S
I IO
/D
EN
P
EQ
R
N
TL O
S
T0 I
T1 I
T2 I
S16
AM BP
RF GND
2 I
C
1 I
I
O
O
I
I
C
17
C
1000p
76
AM RF I
FM MIX O
1000p
2E13,C
RF VCC
AM MIX O
48
C
C
S
D
100k
0
1
2
R
k
70
4
9
C
L4
L
A
R
T
AM OSC
FM/TV OSC
VCC
AGC
C35
C44
4.7
0.022
4V
S
K
O
3
6
R
57
R
10k
60
R
10k
,E13,M
S
U
,A
D
N
,C
A
S
&
C
K
C
R
IN
OSC O
FM IF I
F2
C
S
D
82
0
2
2
C
G
.0
0
MODE2
GND
C
45
C
100
6.3V
4
IC
93C
K
A
R
EEP
S
C
K
S
1
D
0
D
S
K
O
EP
A
54
R
10k
X
0.01
FM
4
1
MODE1
AM IF I
F3
24
R
1k
53
C
0.47
55A
M
O
V
G
K
,U
V
N
N
,C
C
C
E
P
C
D
&
M
REQ SW
QUAD
F4
C
50
C
0.022
,C
A
S
61
R
10k
3
D
35
2S
A
IF COUNT O
DET O
,EE,M
D
N
7
470p
R
10k
39
C
C
0.047
59
3
C
.1
0
LPF2B
MPX I
36
C
4.7
4V
49
C
X
12
C
7
2
C
p
5
00p
1
12
R
1k
2
L O
LPF2A
R O
LPF1
40
C
0.01
41
C
0.01
99
1
85
R
0
80
R
0
43
0
R
56
R
10k
,E13
S
U
2E13,A
55
R
10k
,EE
K
,U
EP
A
C
1
R
0p
22
0k
IC
4FN
N
M
0.047
C
TU
C
K
K
50
D
R
47
2
L
FM
C
EN
U
EQ
R
F
E
G
A
ER
V
O
C
1
)
(EL
M
/A
,
D
N
TE
X
P
7
Q
144TU
TC
D
H
ITC
W
S
C42
P
TU
N
O
D
N
O
EL
S
2
EY
1
EY
L
X
TS
EQ
4
D
Y
A
W
57
3
2S
A
M
T
N
A
FM
L
TU
R
TU
2-4
B
3
Q
A
144TU
TA
D
ITCH
SW
2
Q
A
144TU
TA
D
H
ITC
W
S
8
18
R
47k
N
O
R
Q
A
144TU
TC
D
H
ITC
W
S
19
L9
R
47
T
U
O
V
D
N
G
2S
V
B
B
IN
2S
+ S
B
11
Q
167900LS
+ SW
5
Q
1576
A
H
ITC
W
2V
U
P
C
&
100k
V
TU
D
N
G
A
IN
V
D
N
G
D
1-4
B
1
B
3-4
B
1
S
TEP
S
9k
10k
52
R
X
,E13,M
S
U
,A
D
N
,C
A
S
23
R
4.7k
10
Q
A
144TU
TC
D
H
ITC
+ SW
B
46
C
9
Q
A
144TU
TC
D
W
+ S
B
O
H
ITC
62R
C
X
1.6V
IC
P
ITC
2
1602M
EG
R
47
H
6.3V
L606
0
25
R
4.7k
R
1
C
.
6.3V
C55
47
1
22
R
47k
2E13,C
2
L
3
2
C
1
.0
0
1
1
R
.2k
2
31
C
.01
0
215
A
T
FM
O
FR
FM
S
M
G
P
D
A
D
A
41
R
0
R
470k
EN
P
O
D
LC
80
C
1000p
16
16
Page 17
D-FJ211
p
p
p
p
p
3.0 Vp-p
5.7
µ
sec
Ver 1.1 2003.03
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specifed.
• C : panel designation.
Note: Note:
The components identi- Les composants identifiés
fied by mark 0 or dotted par une marque 0 sont criline with mark 0 are cri- tiques pour la sécurité.
tical for safety. Ne les remplacer que par
Replace only with part une piéce portant le
number specified. numéro spécifié.
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 3 V and fed with regulated dc power supply
from battery terminal.
•Voltages are dc with respect to ground under no-signal(detuned)
conditions.
no mark : FM
(): AM
[]: CD PLAY
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production toler
ances.
• Circled numbers refer to waveforms.
• Signal path.
E : CD PLAY
F : FM
f : AM
• Abbreviation
CND : Canadian
C&SA : Central and South America
EE : East European
AUS : Australian
MX : Mexican
E13 : AM frequency range 531-1,602 kHz
2E13 : AM frequency range 531-1,710 kHz
Note on Printed Wiring Boards:
Note:
• X : parts extracted from the component side.
• a : Through hole.
•
• Abbreviation
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Caution:
Pattern face side :Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side : Parts on the parts face side seen from the
(Side A) parts face are indicated.
CND : Canadian
C&SA : Central and South America
EE : East European
AUS : Australian
MX : Mexican
E13 : AM frequency range 531-1,602 kHz
2E13 : AM frequency range 531-1,710 kHz
r
Waveforms
1
75 KHz
IC3 uf
X_O
(FM/AM/TV/WB MODE)
2
0.29 µsec
Q14 C
3
1.0 Vp-p
VOLT/DIV : 0.5 V AC
TIME/DIV : 5 µsec
4.0 Vp-
VOLT/DIV : 2 V AC
TIME/DIV : 0.1 µsec
0.45 to 0.75Vp-
(CD PLAY MODE)
4
16.934MHz
IC601ek
X_O
(CD PLAY MODE)
5
235
IC601 td
CLK4M
(CD PLAY MODE)(CD PLAY MODE)
6
1.2 Vp-
VOLT/DIV : 1 V AC
TIME/DIV : 20 nsec
2.0Vp-p
µ
sec
VOLT/DIV : 1 V AC
TIME/DIV : 0.1 µsec
2.0Vp-
(CD PLAY MODE)
7
IC403 qd
DSW
(CD PLAY MODE)
8
5.7 µsec
IC403 wa
GSW
VOLT/DIV : 1 V AC
TIME/DIV : 2 µsec
6.0 Vp-
VOLT/DIV : 2 V AC
TIME/DIV : 2 µsec
IC601 qd
RF_I
VOLT/DIV : 0.2 V AC
TIME/DIV : 0.5 µsec
IC801 2
X_I
235 µsec
VOLT/DIV : 1 V AC
TIME/DIV : 0.1 µsec
17
Page 18
D-FJ211
• IC BLOCK DIAGRAM
IC1 TA2154FN (EL)
FM RF OUT
TV RF OUT
30
29
AM BYPASS
28
AM RF IN
27
AM
MIX
26
RFVCC
25
AM
OSC
BUFF
AM OSC
1/2
FM
OSCTVOSC
TV FM OSC
24
OSC OUT
23
BUFF
1/8 OR
1/16
MODE2
22
FM/AM/TV
PW SW
21
MODE1
20
IF REQ
IF COUNT
19
SW
18
LPF2B
17
LPF2A
L OUT
16
TV RF
1
TV RF IN
IC601 BU9354KV
AVDD1
1
LD
2
PD
3
VMON
4
VCHK
5
VE
6
VF
7
VBD
8
VAC
9
AVSS1
10
VBIAS
11
N.C.
12
RF1
13
PKC
14
BTC
15
RFGO
16
DETI
17
ASYI
18
ASYO
19
MON1
20
MON2
21
ADPFO
22
ADPFI
23
FCO
24
PCO
25
FM RF
2
FM FR IN
APC
A/D
RF
AMP
D/A
PLL
IF BUFF
BUFF
6
AGC
SERVO CORE
FM IF
7
VCC
ESP
CLOCK
GEN
FM/TV
MIX
4
3
FM MIX
RF GND
A399A298A197A096A495A594A693A792A891A990RASB88D187D086DVDDIO285D384D283CAS1B82A10/CAS2B81DVSSIO280DVDDIO79SDOP78SDON77TDOP76TDON
100
AGC
5
AM MIX
WINDOW ECC
1bit DAC
8
FM IF IN
89
AM IF
9
GND
WEB
LEVEL
DET
AM
DET
FM
DET
11
10
QUAD
AM IF IN
SUB SIO
AF
12
DET OUT
13
PWM
FLAG
MPX IN
FM MPX
14
LPF IN
15
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
R OUT
FDOP
FDON
CLVOP
CLVON
CLKDRV
SYNC
EXPLCK
TEST_S
EFM/YFLG
C2FX
FOK
DEFECT
LRCKI
DOUTAI
LRCKO
DOUTAO
DOCKO
TEST
N.C.
N.C.
N.C.
N.C.
CLK4M
BUSYB
DVDD
18
26
27
AVSS2
28
RLINO
29
RLINI
30
RDACO
VCDACO
31
32
LLINI
LDACO
33
34
LLINO
35
MUTE
AVDD2
36
37
XIN
DVDD1
38
39
XOUT
40
DVDD
DVSSIO
41
42
DOCKI
43
DVSS1
SBSY
44
45
RSTB
46
PDWNB
DVSSIO
47
48
49
50
SRW
SDIN
SCLK
SDOUT
Page 19
IC403 BH6580KV
61
60
DCIN
59
58
57 56
55
54 53 51 50 49 47 46 454852
36
35
34
32
31
30
33
23
22
29
27
26
25
24
28
21
91 2 3 4 7 85 6 10 11 12 13 14 15 16
62
REGB
63
DET
64
DCIN_S
65
CHGB
66
VMMNT
67
CHGMNT
68
BATM1
69
BATM2
70
BBK
71
PREGND
72
PWM
73
SOFTPWM
74
FG
75
CSL1
SPVCC1
U_OUT
SPGND1
V_OUT
SPVCC2
W_OUT
LG
SPGND2
VG
SSW
VCC3
VIN
DSW
POWERGND
USW
VCC017VCC118VCC2
20
VCC
FIN3
RIN3
FIN2
RIN2
FIN1
RIN1
VM1
0GND
FO1
PGND1
VM12
RO1
FO2
PGND2
RO2
VM23
44
FO343PGND342RO341VM3
76
WI
PRE DRIVE
LOGIC
VG
VCC
VG
SLOPE
SIGNAL
77
VI
78
UI
79
COM
80
CSL2
XRST
37
WAKEUP
38
CLOXK
39
DATA
40
LATCH
RESET_O
SYNC
PREGND
EI
SOFT
SLOW
EO
PMG
VCPUNF
VCC2NF
STNG
SEP
SEM
SEO
GSW
INPUT
SELECT
CHARGE
CONTROLLER
LEVEL
SHIFTER
HVPROT
MONTOR
AMP
VM
VCC
VG
VG
VCC3
CH1
H BRIDGE
CH2
H BRIDGE
CH3
H BRIDGE
INTERFACE
RESET
CLK
SAW GEN
VG
VCC
VCC2
19
VCPU_2.0V
10msec
DELAY
VCC4
D-FJ211
19
Page 20
D-FJ211
5-8. IC PIN FUNCTION DESCRINTION
IC801 (SYSTEM CONTROL) T5AW6-Z7C
Pin No. Pin name I/O Description
1 GND – Ground terminal
2 XIN I System clock input
3 XOUT O Not used (OPEN)
4 TEST I Test mode terminal
5 VCPU_2.0V – Power supply for CPU & I/O
6 FOK_I I Focus OK signal input
7 XBUSY_I I DSP’s auto sequencer status
8 RESET_I I/O Micon reset terminal
9 ACKCD_I I ACK signal input
10 SDTI_I_TU I Signal data input from TC9327AF-641
11 SCOR_I I SCOR pulse input
12 HPSW_O O Headphone IC power switch
13 DEFECT_I I DEFECT signal input
14 XPOWLT_O O Power IC’s serial interface latch output
15 SRW_O O DSP’s serial interface Read/Write signal output
16 SDTI_I I Serial interface input
17 SDTO_O O Serial interface output
18 SCK_O O Serial interface clock output
19 AVCPU – Power supply for CPU and I/O
20 ADVREF – Analog reference voltage for A/D converter
21 AD_SEL I Test mode detection input
22 AD_CHGMNT I Charging monitor input
23 AD_KEY2 I Key input
24 AD_BATTMNT I Battery voltage monitor input
25 WP/AD_KEY1 I Set’s key detection input
26 WP/AD_RMKEY I Remocon’s key detection input
27 AD_DCINMNT I DC voltage monitoring input
28 WP/XOPEN I OPEN switch status detection input
29 TUPWR O Power supply for tuner
30 BEEP_O O BEEP sound
31 NC O Not used (OPEN)
32 VDD_EEPROM – Power supply for EEPROM (OPEN)
33 WP/K2_RM I Wake-up signal input
34 TU_ON_I I Tuner ON signal input
35 TEST O Not used (OPEN)
36 X4M/16M_I I DRAM size selection terminal (fixed at H)
37 XL_O O Line out detection signal output
38 GPROSW_I I ESP switch status detection input
39 LCD_REQ_O O LCD request signal output
40 HOLD_I I HOLD switch status detection input
41 to 56 SEG0-15 O Not used (OPEN)
57-60 COM0-3 O Not used (OPEN)
61-63 V1-3 – Not used (OPEN)
64 C1 – Not used (OPEN)
65 C0 – Not used (OPEN)
66 XWAKEUP_O O Wake-up signal output
67 PGM_SDTO – Not used (OPEN)
20
Page 21
Pin No. Pin name I/O Description
68 PGM_SDTI – Not used (OPEN)
69 PGM_SCK_O – Not used (OPEN)
70 CD_ON O CD ON signal output
71 GFS_I I Guard Frame Synchronous signal input
72 FG_I I FG signal input
73 PGMSEL_O – Not used (OPEN)
74 AMUTE_O O Mute ON/OFF control output
75 RESET_TU_O O Reset signal output
76 XREST_O O System reset output
77 POFF_O O DSP’s power off output
78 XOPSTBY_O O Pick-up’s power supply ON/OFF control
79 OPGSW_O O RF IC’s gain control
80 C2POEN_O O Not used (OPEN)
D-FJ211
21
Page 22
D-FJ211
Ver 1.2 2003.05
SECTION 6
EXPLODED VIEWS
NOTE :
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference
number in the exploded views are not
supplied.
6-1. CABINET SECTION
4
3
5
9
LCD1
6
• Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
• Abbreviation
CND : Canadian
C&SA : Central and South America
EE : East European
AUS : Australian
MX : Mexican
E13 : AM frequency range 531-1,602 kHz
2E13 : AM frequency range 531-1,710 kHz
CDM-3325ER
10
7
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
12
8
17
2
11
13
14
15
16
1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-3383-192-1 CABINET (LOWER) SUB ASSY
2 3-248-574-01 SHEET, SHIELD
* 3 A-3347-658-A MAIN PC BOARD ASSY (AEP,UK,EE)
* 3 A-3347-662-A MAIN PC BOARD ASSY (C&SA,CND,MX)
* 3 A-3347-666-A MAIN PC BOARD ASSY (AUS,E13)
* 3 A-3683-315-A MAIN PC BOARD ASSY (2E13)
4 3-249-578-01 KNOB (GPRO)
5 3-831-441-99 SPACER, KNOB
6 3-246-653-01 TERMINAL BOARD (+), BATTERY
7 3-246-654-01 TERMINAL BOARD (-), BATTERY
8 3-247-456-01 BOARD (RELAY),TERMINAL,BATTERY
9 3-252-360-01 CUSHION (MD)
10 3-245-331-01 INSULATOR
11 4-908-792-61 SCREW (B2)
12 X-3383-195-1 LID ASSY, UPPER
13 3-248-061-01 SPRING (L)
14 3-248-062-01 SPRING (R)
15 X-3383-289-1 CABINET (UPPER) SUB ASSY
16 3-246-595-01 LID, BATTERY CASE
17 3-254-514-01 SHEET (LCD), SHIELD
LCD1 1-804-997-11 DISPLAY PANEL, LIQUID CRYSTAL
22
Page 23
6-2. OPTICAL PICK-UP SECTION
(CDM-3325ER)
103
D-FJ211
101
102
M901
106
108
111
104
M902
107
105
109
110
101
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 3-318-203-61 SCREW (B1.7X4), TAPPING
102 3-221-474-01 SPRING, SLED
103 3-221-472-02 CHASSIS
104 A-3180-952-A FEED ASSY, SCREW
105 3-221-473-01 COVER, GEAR
106 3-221-268-01 GEAR (B)
0 107 X-3380-950-1 OPTICAL PICK-UP (DAX-25E RP ASSY)
108 3-221-475-01 SHAFT, STANDARD
109 3-222-298-01 RACK
110 3-222-299-01 SPRING, RACK RETAINER
111 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN
M901 A-3180-953-A MOTOR ASSY, TURN TABLE (SPINDLE)
M902 A-3180-951-A MOTOR ASSY, SLED (including GEAR)
23
Page 24
D-FJ211
Ver 1.2 2003.05
MAIN
NOTE :
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable
• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-3347-658-A MAIN BOARD, COMPLETE (AEP,UK,EE)
* A-3347-662-A MAIN BOARD, COMPLETE (C&SA,CND,MX)
* A-3347-666-A MAIN BOARD, COMPLETE (AUS,E13)
* A-3683-315-A MAIN BOARD, COMPLETE (2E13)
*******************
ELECTRICAL PARTS LIST
• SEMICONDUCTORS
In each case, u : µ , for example :
uA.... : µ A.... , uPA.... : µ PA....
uPB.... : µ PB.... , uPC.... : µ PC....
uPD.... : µ PD....
• CAPACITORS
uF : µ F
• COILS
uH : µ H
• Abbreviation
CND : Canadian
C&SA : Central and South America
EE : East European
AUS : Australian
MX : Mexican
E13 : AM frequency range 531-1,602 kHz
2E13 : AM frequency range 531-1,710 kHz
SECTION 7
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference number, please include the board.
C46 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C47 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C48 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C49 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C50 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
3-246-653-01 TERMINAL BOARD (+), BATTERY
3-246-654-01 TERMINAL BOARD (-), BATTERY
3-247-456-01 BOARD (RELAY),TERMINAL,BATTERY
3-252-360-01 CUSHION (MD)
< CAPACITOR >
C1 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C2 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C6 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C7 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C9 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C10 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C11 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C12 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C13 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C14 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C18 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C19 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C22 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C23 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C25 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C27 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C30 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C31 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C32 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C33 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C35 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C36 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4V
C39 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C40 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C41 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C42 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C43 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(2E13,C&SA,CND,MX)
C44 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4V
C45 1-128-964-91 TANTAL. CHIP 100uF 20% 6.3V
C53 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C55 1-115-156-11 CERAMIC CHIP 1uF 10V
C58 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C59 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C60 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C61 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C64 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C65 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C66 1-135-834-91 CERAMIC CHIP 2.2uF 6.3V
C67 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C68 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C69 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C70 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(AEP,UK,C&SA,CND,EE,MX)
C71 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C73 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C75 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C76 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C78 1-115-156-11 CERAMIC CHIP 1uF 10V
C80 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C81 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
(AUS,2E13,E13)
C82 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C85 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C87 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C88 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C89 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C92 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C93 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C94 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C95 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C96 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C97 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C99 1-115-156-11 CERAMIC CHIP 1uF 10V
C100 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C101 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
24
Page 25
D-FJ211
Ver 1.2 2003.05
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C102 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C103 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C104 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C105 1-135-834-91 CERAMIC CHIP 2.2uF 6.3V
C110 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C201 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C202 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C203 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C204 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C205 1-135-834-91 CERAMIC CHIP 2.2uF 6.3V
C210 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C300 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
C303 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C304 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C305 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
(AUS,2E13,E13)
C305 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
(AEP,UK,C&SA,CND,EE,MX)
C306 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C307 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C308 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C309 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C310 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
(AEP,UK,C&SA,CND,EE,MX)
C310 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
(AUS,2E13,E13)
C311 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C312 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C313 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
C314 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C315 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C316 1-126-369-11 ELECT 220uF 20% 6.3V
(AEP,UK,C&SA,CND,EE,MX)
C317 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(AUS,2E13,E13)
C318 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C321 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C324 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C325 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C328 1-135-856-91 TANTAL. CHIP 100uF 20% 10V
C400 1-115-156-11 CERAMIC CHIP 1uF 10V
C402 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(AUS,2E13,E13)
C403 1-115-156-11 CERAMIC CHIP 1uF 10V
C404 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C405 1-115-156-11 CERAMIC CHIP 1uF 10V
C406 1-135-834-91 CERAMIC CHIP 2.2uF 6.3V
C408 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(AUS,2E13,E13)
C410 1-115-156-11 CERAMIC CHIP 1uF 10V
C411 1-115-156-11 CERAMIC CHIP 1uF 10V
C415 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C417 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C418 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C419 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C420 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C421 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C422 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C423 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C425 1-126-153-11 ELECT 22uF 20% 6.3V
(EXCEPT AUS,E13)
C426 1-126-369-11 ELECT 220uF 20% 6.3V
C427 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C428 1-107-686-11 TANTAL. CHIP 4.7uF 20% 16V
C429 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C430 1-115-156-11 CERAMIC CHIP 1uF 10V
C432 1-128-829-91 TANTAL. CHIP 220uF 20% 6.3V
C433 1-115-156-11 CERAMIC CHIP 1uF 10V
C434 1-124-589-11 ELECT 47uF 20% 16V
C435 1-126-153-11 ELECT 22uF 20% 6.3V
C436 1-124-589-11 ELECT 47uF 20% 16V
(EXCEPT AUS,E13)
C437 1-124-589-11 ELECT 47uF 20% 16V
(EXCEPT AUS,E13)
C438 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C439 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C440 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C441 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C442 1-124-584-00 ELECT 100uF 20% 10V
C443 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C445 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C447 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C448 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C450 1-115-156-11 CERAMIC CHIP 1uF 10V
C600 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C604 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C605 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C606 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C607 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C608 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C609 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C610 1-135-834-91 CERAMIC CHIP 2.2uF 6.3V
(AEP,UK,C&SA,CND,EE,MX)
C610 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
(AUS,2E13,E13)
C612 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C613 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C614 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C618 1-135-834-91 CERAMIC CHIP 2.2uF 6.3V
C619 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C620 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C621 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C622 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C623 1-115-156-11 CERAMIC CHIP 1uF 10V
C624 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C625 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C626 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C627 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C629 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C630 1-128-964-91 TANTAL. CHIP 100uF 20% 6.3V
C631 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C632 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(AUS,2E13,E13)
C633 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C800 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C801 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C802 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C803 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C804 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C805 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
25
Page 26
D-FJ211
Ver 1.1 2003.03
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C806 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C807 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C808 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C809 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C810 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(AUS,2E13,E13)
C811 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(AUS,2E13,E13)
< CERAMIC FILTER >
CF2 1-795-035-11 FILTER, CERAMIC
CF3 1-781-271-11 FILTER, CERAMIC
CF4 1-795-845-21 DISCRIMINATOR, CERAMIC
CF5 1-760-130-11 VIBRATOR, CRYSTAL
< CONNECTOR >
IC1 6-701-310-01 IC TA2154FN(EL)
IC2 8-759-457-70 IC XC62RP1602MR
IC3 6-802-330-01 IC TC9327AF-Z7CTU
IC4 8-759-449-23 IC AK93C55AV-L
IC301 6-703-718-01 IC AN17882A-E1
IC403 6-703-034-01 IC BH6580KV
IC601 6-703-033-01 IC BU9354KV
IC603 6-703-609-01 IC MSM51X4400E-10TSK-FS
IC801 6-802-331-01 IC T5AW6-Z7C
J301 1-815-135-32 JACK, HEADPHONE (i)
J401 1-778-153-51 JACK,DC(POLARITY UNIFIED TYPE)
< IC >
< JACK >
(DC IN 4.5V)
CN401 1-784-342-21 HOUSING, CONNECTOR 2P
* CN402 1-785-877-21 HOUSING, CONNECTOR 4P
* CN601 1-816-237-21 CONNECTOR, FFC/FPC (ZIF) 15P
< TRIMMER CAPACITOR >
CT1 1-141-374-11 CAP, TRIMMER 20PF (AM TRACKING)
< DIODE >
D1 8-719-076-70 DIODE KV1520TL
D3 8-719-080-77 DIODE MA2S357(E)-(TX).SO
D4 8-719-080-77 DIODE MA2S357(E)-(TX).SO
D6 8-719-404-50 DIODE MA111-TX
D7 8-719-420-87 DIODE MA8130
D301 8-719-044-74 DIODE MA792WK-TX
D302 8-719-044-74 DIODE MA792WK-TX
D306 8-719-059-53 DIODE MA3J14700LSO
D402 8-719-067-42 DIODE MA2H735-(TX).SO
D403 8-719-067-42 DIODE MA2H735-(TX).SO
D405 8-719-085-43 DIODE MA2YD2300LS0
D406 8-719-069-54 DIODE UDZSTE-175.1B
D408 8-719-404-50 DIODE MA111-TX
D409 8-719-404-50 DIODE MA111-TX
D410 8-719-067-42 DIODE MA2H735-(TX).SO
D802 8-719-072-70 DIODE MA2ZD14001S0
D804 8-719-421-27 DIODE MA728
D805 8-719-421-27 DIODE MA728
< FERRITE BEAD >
FB101 1-414-760-21 FERRITE 0uH
FB201 1-414-760-21 FERRITE 0uH
FB301 1-414-813-11 FERRITE 0uH
FB401 1-216-295-91 SHORT CHIP 0
FB402 1-216-295-91 SHORT CHIP 0
FB403 1-216-295-91 SHORT CHIP 0
FB404 1-216-295-91 SHORT CHIP 0
FB405 1-216-295-91 SHORT CHIP 0
FB406 1-216-295-91 SHORT CHIP 0
FB408 1-216-295-91 SHORT CHIP 0
< FILTER >
FL2 1-236-711-21 FILTER, BAND PASS
< COIL >
L1 1-424-851-31 COIL, FERRITE-ROD ANTENNA (MW)
(AM TRACKING)
L2 1-419-542-11 COIL, AIR-CORE (FM FREQUENCY COVERAGE)
L4 1-456-313-11 COIL, AIR-CORE (FM TRACKING)
L5 1-424-883-11 COIL (AM OSC) (AM FREQUENCY COVERAGE)
L9 1-414-398-11 INDUCTOR 10uH
L10 1-412-006-31 INDUCTOR 10uH
L11 1-412-006-31 INDUCTOR 10uH
L401 1-412-056-11 INDUCTOR 4.7uH
L402 1-412-056-11 INDUCTOR 4.7uH
L403 1-400-145-21 INDUCTOR 47uH
L404 1-414-406-41 INDUCTOR 220uH
L405 1-216-295-91 SHORT CHIP 0
L406 1-400-145-21 INDUCTOR 47uH
L407 1-419-387-21 INDUCTOR 100uH
L409 1-400-145-21 INDUCTOR 47uH
L410 1-400-145-21 INDUCTOR 47uH
L411 1-410-389-31 INDUCTOR CHIP 47uH
L601 1-469-967-21 INDUCTOR 10uH
L602 1-216-295-91 SHORT CHIP 0
L603 1-412-006-31 INDUCTOR 10uH
L604 1-412-006-31 INDUCTOR 10uH
L605 1-216-295-91 SHORT CHIP 0
L606 1-216-295-91 SHORT CHIP 0
< LIQUID CRYSTAL DISPLAY >
LCD1 1-804-997-11 DISPLAY PANEL, LIQUID CRYSTAL
< TRANSISTOR >
Q2 8-729-028-92 TRANSISTOR DTA144TUA-T106
Q3 8-729-028-92 TRANSISTOR DTA144TUA-T106
Q4 8-729-602-21 TRANSISTOR 2SC4154-F
(2E13,C&SA,CND,MX)
Q5 8-729-026-53 TRANSISTOR 2SA1576A-T106-QR
Q7 8-729-029-15 TRANSISTOR DTC144TUA-T106
Q8 8-729-028-97 TRANSISTOR DTC114TUA-T106
Q9 8-729-028-97 TRANSISTOR DTC114TUA-T106
Q10 8-729-028-97 TRANSISTOR DTC114TUA-T106
Q11 8-729-054-79 TRANSISTOR 2SB167900LSO
Q12 8-729-053-44 TRANSISTOR 2SK880-Y-TE85R
26
Page 27
D-FJ211
Ver 1.2 2003.05
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q13 8-729-602-21 TRANSISTOR 2SC4154-F
Q14 8-729-602-21 TRANSISTOR 2SC4154-F
Q15 8-729-423-52 TRANSISTOR 2SC3931-C
Q301 8-729-029-10 TRANSISTOR DTC143TUA-T106
R50 1-216-853-11 METAL CHIP 470K 5% 1/10W
R52 1-216-845-11 METAL CHIP 100K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R53 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
Q401 8-729-921-73 TRANSISTOR 2SD1781K-QR
Q402 6-550-070-01 TRANSISTOR 2SB1237TV2PQR
Q403 8-729-231-74 TRANSISTOR 2SC4116-GL
Q404 8-729-054-79 TRANSISTOR 2SB167900LSO
Q405 8-729-047-36 TRANSISTOR CPH3303-TL
Q406 8-729-044-84 TRANSISTOR CPH3403-TL-E
Q407 8-729-905-40 TRANSISTOR 2SC4081T106
Q408 8-729-905-40 TRANSISTOR 2SC4081T106
Q601 8-729-054-79 TRANSISTOR 2SB167900LSO
Q801 8-729-029-10 TRANSISTOR DTC143TUA-T106
Q802 8-729-231-74 TRANSISTOR 2SC4116-GL
< RESISTOR >
R1 1-216-853-11 METAL CHIP 470K 5% 1/10W
R2 1-216-853-11 METAL CHIP 470K 5% 1/10W
R3 1-216-833-11 METAL CHIP 10K 5% 1/10W
R6 1-216-853-11 METAL CHIP 470K 5% 1/10W
R7 1-216-853-11 METAL CHIP 470K 5% 1/10W
R8 1-216-833-11 METAL CHIP 10K 5% 1/10W
R10 1-216-864-11 METAL CHIP 0 5% 1/10W
R11 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R12 1-216-821-11 METAL CHIP 1K 5% 1/10W
R18 1-216-841-11 METAL CHIP 47K 5% 1/10W
R19 1-216-805-11 METAL CHIP 47 5% 1/10W
R21 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(2E13,C&SA,CND,MX)
R22 1-216-841-11 METAL CHIP 47K 5% 1/10W
R23 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R24 1-216-821-11 METAL CHIP 1K 5% 1/10W
R25 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R27 1-216-837-11 METAL CHIP 22K 5% 1/10W
(C&SA,CND,MX)
R28 1-216-864-11 METAL CHIP 0 5% 1/10W
R29 1-216-845-11 METAL CHIP 100K 5% 1/10W
R30 1-216-833-11 METAL CHIP 10K 5% 1/10W
R31 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R32 1-216-817-11 METAL CHIP 470 5% 1/10W
R33 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R34 1-216-821-11 METAL CHIP 1K 5% 1/10W
R35 1-216-845-11 METAL CHIP 100K 5% 1/10W
R36 1-216-813-11 METAL CHIP 220 5% 1/10W
R37 1-216-845-11 METAL CHIP 100K 5% 1/10W
R38 1-216-821-11 METAL CHIP 1K 5% 1/10W
R39 1-216-817-11 METAL CHIP 470 5% 1/10W
R40 1-216-845-11 METAL CHIP 100K 5% 1/10W
R41 1-216-864-11 METAL CHIP 0 5% 1/10W
R42 1-216-833-11 METAL CHIP 10K 5% 1/10W
R43 1-216-864-11 METAL CHIP 0 5% 1/10W
R44 1-216-864-11 METAL CHIP 0 5% 1/10W
R45 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AUS,2E13,E13)
R46 1-216-845-11 METAL CHIP 100K 5% 1/10W
(AUS,2E13,E13)
R49 1-216-833-11 METAL CHIP 10K 5% 1/10W
R55 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R56 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AUS,2E13,E13)
R57 1-216-833-11 METAL CHIP 10K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R59 1-216-833-11 METAL CHIP 10K 5% 1/10W
R60 1-216-833-11 METAL CHIP 10K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R61 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,C&SA,CND,EE,MX)
R63 1-216-845-11 METAL CHIP 100K 5% 1/10W
R78 1-216-864-11 METAL CHIP 0 5% 1/10W
R80 1-216-864-11 METAL CHIP 0 5% 1/10W
R82 1-216-864-11 METAL CHIP 0 5% 1/10W
R84 1-216-864-11 METAL CHIP 0 5% 1/10W
R85 1-216-864-11 METAL CHIP 0 5% 1/10W
R101 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R101 1-216-864-11 METAL CHIP 0 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R102 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R102 1-216-837-11 METAL CHIP 22K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R103 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(AEP,UK,EE)
R103 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R104 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R105 1-216-833-11 METAL CHIP 10K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R105 1-216-837-11 METAL CHIP 22K 5% 1/10W
(AEP,UK,EE)
R106 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R106 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R109 1-216-864-11 METAL CHIP 0 5% 1/10W
R201 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R201 1-216-864-11 METAL CHIP 0 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R202 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R202 1-216-837-11 METAL CHIP 22K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R203 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(AEP,UK,EE)
R203 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R204 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R205 1-216-833-11 METAL CHIP 10K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R205 1-216-837-11 METAL CHIP 22K 5% 1/10W
(AEP,UK,EE)
R206 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R206 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
27
Page 28
D-FJ211
Ver 1.2 2003.05
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R209 1-216-864-11 METAL CHIP 0 5% 1/10W
R300 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R301 1-216-837-11 METAL CHIP 22K 5% 1/10W
R302 1-216-793-11 METAL CHIP 4.7 5% 1/10W
R304 1-216-864-11 METAL CHIP 0 5% 1/10W
(AEP,UK,C&SA,CND,EE,MX)
R309 1-216-864-11 METAL CHIP 0 5% 1/10W
R310 1-216-837-11 METAL CHIP 22K 5% 1/10W
R311 1-216-845-11 METAL CHIP 100K 5% 1/10W
R403 1-218-446-11 METAL CHIP 1 5% 1/10W
R407 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R408 1-216-809-11 METAL CHIP 100 5% 1/10W
R411 1-218-903-11 METAL CHIP 220K 0.5% 1/10W
R412 1-218-887-11 METAL CHIP 47K 0.5% 1/10W
R413 1-216-841-11 METAL CHIP 47K 5% 1/10W
R414 1-216-864-11 METAL CHIP 0 5% 1/10W
R416 1-216-813-11 METAL CHIP 220 5% 1/10W
R419 1-216-833-11 METAL CHIP 10K 5% 1/10W
R420 1-216-845-11 METAL CHIP 100K 5% 1/10W
R421 1-216-833-11 METAL CHIP 10K 5% 1/10W
R422 1-216-295-91 SHORT CHIP 0
R614 1-216-805-11 METAL CHIP 47 5% 1/10W
R615 1-216-864-11 METAL CHIP 0 5% 1/10W
R616 1-216-857-11 METAL CHIP 1M 5% 1/10W
R617 1-216-864-11 METAL CHIP 0 5% 1/10W
R618 1-216-817-11 METAL CHIP 470 5% 1/10W
R619 1-216-817-11 METAL CHIP 470 5% 1/10W
R620 1-216-817-11 METAL CHIP 470 5% 1/10W
R621 1-216-864-11 METAL CHIP 0 5% 1/10W
R624 1-216-833-11 METAL CHIP 10K 5% 1/10W
R626 1-216-864-11 METAL CHIP 0 5% 1/10W
R627 1-216-833-11 METAL CHIP 10K 5% 1/10W
R629 1-216-864-11 METAL CHIP 0 5% 1/10W
R630 1-216-864-11 METAL CHIP 0 5% 1/10W
R631 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R800 1-216-837-11 METAL CHIP 22K 5% 1/10W
(C&SA,CND,MX)
R801 1-216-295-91 SHORT CHIP 0
R802 1-216-864-11 METAL CHIP 0 5% 1/10W
R803 1-216-845-11 METAL CHIP 100K 5% 1/10W
R804 1-216-833-11 METAL CHIP 10K 5% 1/10W
(AEP,UK,EE)
R423 1-216-295-91 SHORT CHIP 0
R424 1-216-295-91 SHORT CHIP 0
R425 1-216-295-91 SHORT CHIP 0
R427 1-216-841-11 METAL CHIP 47K 5% 1/10W
R428 1-216-845-11 METAL CHIP 100K 5% 1/10W
R429 1-216-295-91 SHORT CHIP 0
R430 1-216-821-11 METAL CHIP 1K 5% 1/10W
R431 1-216-845-11 METAL CHIP 100K 5% 1/10W
R432 1-216-821-11 METAL CHIP 1K 5% 1/10W
R433 1-216-845-11 METAL CHIP 100K 5% 1/10W
R434 1-216-845-11 METAL CHIP 100K 5% 1/10W
R435 1-216-833-11 METAL CHIP 10K 5% 1/10W
R436 1-216-864-11 METAL CHIP 0 5% 1/10W
R438 1-216-833-11 METAL CHIP 10K 5% 1/10W
R439 1-216-841-11 METAL CHIP 47K 5% 1/10W
R440 1-216-841-11 METAL CHIP 47K 5% 1/10W
R441 1-216-845-11 METAL CHIP 100K 5% 1/10W
R444 1-216-845-11 METAL CHIP 100K 5% 1/10W
R446 1-216-864-11 METAL CHIP 0 5% 1/10W
R447 1-216-864-11 METAL CHIP 0 5% 1/10W
R448 1-216-864-11 METAL CHIP 0 5% 1/10W
R449 1-216-845-11 METAL CHIP 100K 5% 1/10W
R451 1-218-895-11 METAL CHIP 100K 0.5% 1/10W
R452 1-218-895-11 METAL CHIP 100K 0.5% 1/10W
R600 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R601 1-216-864-11 METAL CHIP 0 5% 1/10W
R602 1-216-845-11 METAL CHIP 100K 5% 1/10W
R603 1-216-845-11 METAL CHIP 100K 5% 1/10W
R604 1-216-845-11 METAL CHIP 100K 5% 1/10W
R605 1-216-845-11 METAL CHIP 100K 5% 1/10W
R606 1-216-797-11 METAL CHIP 10 5% 1/10W
(AUS,2E13,E13)
R608 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R610 1-216-845-11 METAL CHIP 100K 5% 1/10W
R611 1-216-817-11 METAL CHIP 470 5% 1/10W
R612 1-216-864-11 METAL CHIP 0 5% 1/10W
R613 1-216-817-11 METAL CHIP 470 5% 1/10W
R804 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(2E13,C&SA,CND,AUS,E13,MX)
R805 1-216-864-11 METAL CHIP 0 5% 1/10W
R807 1-216-861-11 METAL CHIP 2.2M 5% 1/10W
R808 1-216-857-11 METAL CHIP 1M 5% 1/10W
R809 1-216-833-11 METAL CHIP 10K 5% 1/10W
R810 1-216-837-11 METAL CHIP 22K 5% 1/10W
(C&SA,CND,MX)
R811 1-216-864-11 METAL CHIP 0 5% 1/10W
R812 1-216-864-11 METAL CHIP 0 5% 1/10W
R813 1-216-845-11 METAL CHIP 100K 5% 1/10W
R814 1-216-845-11 METAL CHIP 100K 5% 1/10W
(AEP,UK,C&SA,CND,EE,MX)
R815 1-216-837-11 METAL CHIP 22K 5% 1/10W
(C&SA,CND,MX)
R817 1-216-817-11 METAL CHIP 470 5% 1/10W
R820 1-216-864-11 METAL CHIP 0 5% 1/10W
R821 1-216-864-11 METAL CHIP 0 5% 1/10W
R822 1-216-833-11 METAL CHIP 10K 5% 1/10W
R823 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R825 1-216-864-11 METAL CHIP 0 5% 1/10W
R827 1-216-817-11 METAL CHIP 470 5% 1/10W
R829 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W
R830 1-216-864-11 METAL CHIP 0 5% 1/10W
R831 1-216-864-11 METAL CHIP 0 5% 1/10W
R832 1-216-817-11 METAL CHIP 470 5% 1/10W
R833 1-216-817-11 METAL CHIP 470 5% 1/10W
R835 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R836 1-216-864-11 METAL CHIP 0 5% 1/10W
R837 1-216-817-11 METAL CHIP 470 5% 1/10W
R841 1-216-845-11 METAL CHIP 100K 5% 1/10W
R843 1-216-861-11 METAL CHIP 2.2M 5% 1/10W
R844 1-216-833-11 METAL CHIP 10K 5% 1/10W
R845 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R846 1-216-853-11 METAL CHIP 470K 5% 1/10W
R849 1-216-817-11 METAL CHIP 470 5% 1/10W
R852 1-216-817-11 METAL CHIP 470 5% 1/10W
R854 1-216-864-11 METAL CHIP 0 5% 1/10W
28
Page 29
D-FJ211
Ver 1.2 2003.05
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R858 1-216-821-11 METAL CHIP 1K 5% 1/10W
R859 1-216-821-11 METAL CHIP 1K 5% 1/10W
R863 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R864 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W
R865 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R869 1-216-837-11 METAL CHIP 22K 5% 1/10W
(C&SA,CND,MX)
R871 1-216-849-11 METAL CHIP 220K 5% 1/10W
R872 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R873 1-216-837-11 METAL CHIP 22K 5% 1/10W
R874 1-216-833-11 METAL CHIP 10K 5% 1/10W
< SWITCH >
S1 1-762-078-11 SWITCH, SLIDE (9K/10K) (STEP)
(2E13,C&SA,CND,AUS,E13,MX)
S801 1-786-211-21 SWITCH, KEYBOARD (P MODE/ F )
S802 1-786-211-21 SWITCH, KEYBOARD (SOUND/AVLS)
S803 1-786-211-21 SWITCH, KEYBOARD (VOL -)
S804 1-786-211-21 SWITCH, KEYBOARD (VOL +)
S805 1-786-211-21 SWITCH, KEYBOARD (u)
S806 1-786-211-21 SWITCH, KEYBOARD (x,RADIO OFF)
S807 1-786-211-21 SWITCH, KEYBOARD (.,PRESET/TUNE -)
S808 1-786-211-21 SWITCH, KEYBOARD (> ,PRESET/TUNE +)
S809 1-762-003-11 SWITCH, PUSH (OPEN)
S810 1-762-078-11 SWITCH, SLIDE (HOLD . )
S811 1-553-977-81 SWITCH, SLIDE (G-PROTECTION)
S812 1-786-211-21 SWITCH, KEYBOARD
(RADIO ON/BAND.MEMORY)
3-249-386-31 MANUAL, INSTRUCTION (DUTCH,SWEDISH)
(AEP)
3-249-386-41 MANUAL, INSTRUCTION (GERMAN,ITALIAN)
(AEP)
3-249-386-51 MANUAL, INSTRUCTION (FINNISH) (AEP)
3-249-386-61 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN)
(EE)
3-249-386-71 MANUAL, INSTRUCTION
(HUNGARIAN,POLISH)(EE)
3-249-386-81 MANUAL, INSTRUCTION (CZECH,SLOVAK)(EE)
3-252-536-11 MANUAL, INSTRUCTION
(ENGLISH,SIMPLIFIED CHINESE)(E13)
3-252-536-21 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(2E13)
8-954-008-93 RECEIVER,EAR MDR-E808LP (AEP,UK,EE)
8-954-008-94 RECEIVER MDR-E808LP
(2E13,C&SA,CND,AUS,E13,MX)
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
< TRANSFORMER >
T1 1-449-021-21 TRANSFORMER, DC/DC CONVERTER
< VARISTOR >
VDR401 1-801-864-21 VARISTOR, CHIP
VDR402 1-801-864-21 VARISTOR, CHIP
< VIBRATOR >
X601 1-795-561-21 VIBRATOR, CERAMIC (16.934MHz)
******************************************************
MISCELLANEOUS
*************
0 107 X-3380-950-1 OPTICAL PICK-UP (DAX-25E RP ASSY)
LCD1 1-804-997-11 DISPLAY PANEL, LIQUID CRYSTAL
M901 A-3180-953-A MOTOR ASSY, TURN TABLE (SPINDLE)
M902 A-3180-951-A MOTOR ASSY, SLED (including GEAR)
******************************************************
ACCESSORIES
***********
0 1-477-661-11 ADAPTOR, AC (AC-ET455K) (C&SA,CND,MX)
0 1-477-662-11 ADAPTOR, AC (AC-ET455K) (2E13,AEP,E13,EE)
0 1-477-663-11 ADAPTOR, AC (AC-ET455K) (UK)
0 1-477-664-11 ADAPTOR, AC (AC-ET455K) (AUS)
3-249-386-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
3-249-386-21 MANUAL, INSTRUCTION
(SPANISH,PORTUGUESE)(AEP,C&SA,MX)
(AEP,UK,C&SA,CND,AUS,MX)
29
Page 30
D-FJ211
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision
1.0 2003.02 New
1.1 2003.03 Addition of Australian model (ENG-03008)
1.2 2003.05 Addition of UK model (ENG-03024)
Loading...