Datasheet 74V2G66STR, 74V2G66CTR Datasheet (SGS Thomson Microelectronics)

1/9June 2003

■ HIGH SPEED:

t

PD

= 0.3ns (TYP.) at VCC=5V

t

PD

= 0.4ns (TYP.) at VCC=3.3V

■ LOW POWER DISSIPATION:

I

CC

=1µA(MAX.) at TA= 25°C

■ LOW "ON" RESISTANCE:

R

ON

=6.5Ω (TYP.) AT VCC=5VI

I/O

=1mA

R

ON

=8.5Ω(TYP.) AT VCC=3.3VI

I/O

=1mA

■ SINE WAVE DISTORTION:

0.04% AT V

CC

=3.3Vf=1KHz

■ WIDE OPERATING RANGE:

V

CC

(OPR) = 2V TO 5.5V

■ IMPROVED LATCH-UP IMMUNITY

DESCRIPTION

The 74V2G66 is an advanced high-speed CMOS
DUAL BILATERAL SWITCH fabricated in silicon
gate C

2

MOS technology. It achieves high speed
propagation delay and VERY LOW ON
resistances while maintaining true CMOS low
power consumption. This bilateral switch handles
rail to rail analog and digital signals that may vary
across the full power supply range (from GND to
V

CC

).

The C input is provided to control the switch and
it’s compatible with standard CMOS output; the
switch is ON (port I/O is connected to Port O/ I)
when the C input is held high and OFF (high
impedance state exists between the t w o ports)
when C is held low. It c an be used in m any
application as Batt ery Powered System, Test
Equipment. It’s available in the comm erc ial and
extended temperature range in SOT23-8L
package. All inputs and output are equipped with
protection circuits against s tatic discharge, giving
them ESD immunity and tra nsient excess voltage.

74V2G66

DUAL BILATERAL SWITCH

PIN CONNECTION AND IEC LOGIC SYMBOLS

ORDER CODES

PACKAGE T & R

SOT23-8L 74V2G66STR

SOT23-8L

74V2G66

2/9

INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION

TRUTH TABLE

* : High Impedance State

ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied

RECOMMENDED OPERATING CONDITIONS

1) VINfrom30% to 70% of VCCon control pin

PIN No SYMBOL NAME AND FUNCTION

1, 5 1I/O, 2I/O Independent Input/Output
2, 6 1O/I, 2O/I Independent Output/Input

7, 3 1C, 2C

Enable Input (Active

HIGH)
4 GND Ground (0V)
8

V

CC

Positive Supply Voltage

CONTROL SWITCH FUNCTION

HON

L OFF *

Symbol Parameter Value Unit

V

CC

Supply Voltage

-0.5 to +7.0 V

V

I

DC Input Voltage -0.5 to VCC+ 0.5

V

V

IC

DC Control Input Voltage

-0.5 to +7.0 V

V

O

DC Output Voltage -0.5 to VCC+ 0.5

V

I

IK

DC Input Diode Current

± 20 mA

I

IK

DC Control Input Diode Current

-20 mA

I

OK

DC Output Diode Current

± 20 mA

I

O

DC Output Current

± 50 mA

I

CC

or I

GND

DC VCCor Ground Current

± 50 mA

T

stg

Storage Temperature

-65 to +150 °C

T

L

Lead Temperature (10 sec)

300 °C

Symbol Parameter Value Unit

V

CC

Supply Voltage

2 to 5.5 V

V

I

Input Voltage 0 to V

CC

V

V

IC

Control Input Voltage

0 to 5.5 V

V

O

Output Voltage 0 to V

CC

V

T

op

Operating Temperature

-55 to 125 °C

dt/dv

Input Rise and Fall Time (note 1) V

CC

= 5.0V

0 to 20 ns/V

74V2G66

3/9

DC SPECIFICATIONS

(*) Voltage range is3.3V ± 0.3V
(**) Voltage range is 5V ± 0.5V

AC ELECTRICAL CHARACTERISTICS (CL= 50pF, Input tr=tf= 3ns)

(*) Voltage range is3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

V

IH

High Level Input
Voltage

2.0 1.5 1.5 1.5
V

2.7to

5.5

0.7V

CC

0.7V

CC

0.7V

CC

V

IL

Low Level Input
Voltage

2.0 0.5 0.5 0.5
V

2.7to

5.5

0.3V

CC

0.3V

CC

0.3V

CC

R

ON

ON Resistance

3.3

(*)

VIC=V

IH

V

I/O=VCC

to GND

I

I/O

≤ 1mA

12.5 19 23 27

Ω

5.0

(**)

7.5 10 12 14

R

ON

ON Resistance

3.3

(*)

VIC=V

IH

V

I/O=VCC

or GND

I

I/O

≤ 1mA

8.5 10.5 12.5 15

Ω

5.0

(**)

6.5 8.5 10 12

I

OFF

Input/Output
Leakage Current
(SWITCH OFF)

5.5

V

OS=VCC

to GND

V

IS=VCC

to GND

V

IC=VIL

±0.1 ± 1 ± 5 µA

I

IZ

Switch Input
Leakage Current
(SWITCH ON,
OUTPUT OPEN)

5.5

V

OS=VCC

to GND

V

IC=VIH

±0.1 ± 1 ± 5 µA

I

IN

Control Input
Leakage Current

0to

5.5

V

IC

= 5.5V or GND

± 0.1 ± 1.0 ± 1.0 µA

I

CC

Quiescent Supply
Current

5.5

V

I=VCC

or GND

11020µA

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

t

PD

Delay Time

3.3

(*)

tr=tf=6ns

0.4 0.8 1.2 2.4
ns

5.0

(**)

0.3 0.6 1.0 2.0

t

PLZ

t

PHZ

Output Disable
Time

3.3

(*)

RL= 500 Ω

5.0 7.5 9.0 10.0
ns

5.0

(**)

5.0 7.5 9.0 10.0

t

PZL

t

PZH

Output Enable
Time

3.3

(*)

RL=1KΩ

2.5 4.0 5.0 7.0
ns

5.0

(**)

2.0 4.0 5.0 7.0

74V2G66

4/9

CAPACITIVE CHARACTERISTICS

1) CPDis defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumptionwithout
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I

CC(opr)=CPDxVCCxfIN+ICC

/4

ANALOG SWITCH CHARACTERISTICS (GND = 0V; TA= 25°C)

(*)Voltage range is 3.3V ± 0.3V
(**)Voltagerange is 5.0V ± 0.5V

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

C

IN

Input Capacitance

310 10 10pF

C

I/O

Output
Capacitance

10 pF

C

PD

Power Dissipation
Capacitance
(note 1)

3.3 2.5
pF

5.0 3

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

V

IN

(V

p-p

)

Typ.

Sine Wave
Distortion (THD)

3.3

(*)

2.75
f

IN

=1KHzRL=10KΩ,CL=50pF

0.04
%

5.0

(**)

4 0.04

f

MAX

Frequency
Response
(Switch ON)

3.3

(*)

Adjust fINvoltage to obtain 0 dBm at VOS.

Increase f

IN

Frequency until dB meter reads -3dB

R

L

=50Ω,CL=10pF

150

MHz

5.0

(**)

180

Feed through
Attenuation
(Switch OFF)

3.3

(*)

VINis centered at VCC/2

Adjust f

IN

Voltage to obtained 0dBm at V

IS

RL= 600Ω,CL=50pF,fIN= 1KHz sine wave

-60
dB

5.0

(**)

-60

Crosstalk (Control
Input to Signal
Output)

3.3

(*)

RL= 600Ω,CL=50pF,fIN= 1KHz square wave

t

r=tf

=6ns

60

mV

5.0

(**)

60

74V2G66

5/9

SWITCHINGCARACTERISTICSTESTCIRCUIT

FEEDTHROUGH ATTENUATION

CROSSTALK (control to output

BANDWIDTH ATTENUATION

MAXIMUM CONTROL FREQUENCY

74V2G66

6/9

CHANNEL RESISTANCE (R

ON)

ICC(Opr.)

74V2G66

7/9

DIM.

mm. mils

MIN. TYP MAX. MIN. TYP. MAX.

A 0.90 1.45 35.4 57.1

A1 0.00 0.15 0.0 5.9

A2 0.90 1.30 35.4 51.2

b 0.22 0.38 8.6 14.9

C 0.09 0.20 3.5 7.8

D 2.80 3.00 110.2 118.1

E 2.60 3.00 102.3 118.1

E1 1.50 1.75 59.0 68.8

e0.65 25.6

e1 1.95 76.7

L 0.35 0.55 13.7 21.6

SOT23-8L MECHANICAL DATA

74V2G66

8/9

DIM.

mm. inch

MIN. TYP MAX. MIN. TYP. MAX.

A 180 7.086
C 12.8 13.0 13.2 0.504 0.512 0.519
D 20.2 0.795
N 60 2.362

T 14.4 0.567
Ao 3.13 3.23 3.33 0.123 0.127 0.131
Bo 3.07 3.17 3.27 0.120 0.124 0.128
Ko 1.27 1.37 1.47 0.050 0.054 0.0.58
Po 3.9 4.0 4.1 0.153 0.157 0.161

P 3.9 4.0 4.1 0.153 0.157 0.161

Tape & Reel SOT23-xL MECHANICAL DATA

74V2G66

9/9

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use o f suc h inf ormat ion n or f or an y infr ingeme nt of paten ts or oth er ri gh ts of third part ies whic h may resul t f rom
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.

© The ST logo is a registered trademark of STMicroelectronics

© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved

STMicroelectronics GROUP OF COMPANIES

Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco

Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.

© http://www.st.com