Datasheet 74LVX244 Datasheet (ST)

74LVX244

LOW VOLTAGE CMOS OCTAL BUS BUFFER

WITH 3 STATE OUTPUTS (NON INVERTED)

■ HIGH SPEED:

t

=4.5ns (TY P.) at VCC = 3.3V

PD

■ 5V TOLERANT INPUTS

■ POWER-DOWN PROTECTION ON INPUTS

■ INPUT VOLTAGE LEVEL:

V

= 0.8V, VIH = 2V at VCC =3V

IL

■ LOW POWER DISSIPATION:

I

= 4 µA (MAX.) at TA=25°C

CC

■ LOW NOISE:

V

= 0.5V (TYP.) at VCC =3.3V

OLP

■ SYMMETRICAL OUTPUT IMPEDANCE:

|I

| = IOL = 4 mA (MIN) at VCC =3V

OH

■ BALANCED PROPAGATION DELAYS:

t

≅ t

PLH

PHL

■ OPERATING VOLTAGE RANGE:

V

(OPR) = 2V to 3.6V (1.2V Data Retention)

CC

■ PIN AND FUNCTION COMPATIBLE WITH

74 SERIES 244

■ IMPROVED LATCH-UP IMMUNITY

DESCRIPTION

The 74LVX244 is a low voltage CMOS OCTAL
BUS BUFFER (3-STATE) fabricated with
sub-micron silicon gate and double-layer metal
wiring C

2

MOS technology. It is ideal for low
power, battery operated and low noise 3.3V
applications.

TSSOPSOP

Table 1: Order Codes

PACKAGE T & R

SOP 74LVX244MTR

TSSOP 74LVX244TTR

G

output enable governs four BUS BUFFERs
Power down protection is provided on all inputs
and 0 to 7V can be accepted on inputs with no
regard to the supply voltage.
This device can be used to interface 5V to 3V. It
combines high speed performance with the true
CMOS low power consumption.
All inputs and outputs are equipped with
protection circuits against static disc harge, giving
them 2KV ESD immunity and transient excess
voltage.

Figure 1: Pin C onnection And IEC Logic Symbol s

Rev. 4

1/12August 2004

74LVX244

Figure 2: Input Equivalent Circuit Table 2: Pin Description

PIN N° SYMBOL NAME AND FUNCTION

11G
2, 4, 6, 8 1A1 to 1A4 Data Inputs
9, 7, 5, 3 2Y1 to 2Y4 Data Outputs

11, 13, 15, 172A1 to 2A4 Data Inputs

Output Enable Input

18, 16, 14, 121Y1

19 2G

to 1Y4 Data Outputs

Output Enable Input
10 GND Ground (0V)
20 V

CC

Positive Supply Voltage

Table 3: Truth Table

INPUTS OUTPUT

G

An Yn

LLL
LHH

HXZ

X :Don‘t Care
Z : High Impedance

Table 4: Absolute Maximum Ratings

Symbol Parameter Value Unit

V

V

V

I

I

OK

I

or I

I

CC

T

T

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied

Supply Voltage

CC

DC Input Voltage

I

DC Output Voltage -0.5 to VCC + 0.5

O

DC Input Diode Current

IK

DC Output Diode Current
DC Output Current

O

DC VCC or Ground Current

GND

Storage Temperature

stg

Lead Temperature (10 sec)

L

-0.5 to +7.0 V

-0.5 to +7.0 V
V

- 20 mA

± 20 mA
± 25 mA
± 50 mA

-65 to +150 °C

300 °C

Table 5: Recommended Operating Conditions

Symbol Parameter Value Unit

V

V
V
T

dt/dv

1) Truth T abl e guarante ed: 1.2V to 3.6V

2) V

from 0.8V to 2.0V

IN

Supply Voltage (note 1)

CC

Input Voltage

I

Output Voltage 0 to V

O

Operating Temperature

op

Input Rise and Fall Time (note 2) (V

CC

= 3V)

2 to 3.6 V
0 to 5.5 V

CC

-55 to 125 °C
0 to 100 ns/V

2/12

V

Table 6: DC Specifications

Symbol Parameter

V

V

V

High Level Input

IH

Voltage

V

Low Level Input

IL

Voltage

High Level Output

OH

Voltage

Low Level Output

OL

Voltage

High Impedance

I

OZ

Output Leakage
Current

I

Input Leakage

I

Current

I

Quiescent Supply

CC

Current

74LVX244

Test Condition Value

= 25°C

T

V

CC

(V)

A

Min. Typ. Max. Min. Max. Min. Max.

2.0 1.5 1.5 1.5

2.0 2.0 2.0

3.6

2.4 2.4 2.4

2.0 0.5 0.5 0.5

3.6 0.8 0.8 0.8
=-50 µA

2.0

3.0

2.0

3.0

3.6

3.6

3.6

V

VO = VCC or GND

= 5.5V or GND

V

I

V

I

I

O

=-50 µA

I

O

=-4 mA

I

O

IO=50 µA
I

=50 µA

O

=4 mA

I

O

= VIH or V

I

= VCC or GND

1.9 2.0 1.9 1.9

2.9 3.0 2.9 2.9

2.58 2.48 2.4

0.0 0.1 0.1 0.1

0.0 0.1 0.1 0.1

IL

±0.25 ± 2.5 ± 2.5 µA

-40 to 85°C -55 to 125°C

0.36 0.44 0.55

± 0.1 ± 1 ± 1 µA

44040µA

Unit

V3.0

V3.0 0.8 0.8 0.8

V3.0

V3.0

Table 7: Dynamic Switching Characteristics

Test Condition Value

= 25°C

Symbol Parameter

V
V

Dynamic Low

OLP

Voltage Quiet

OLV

Output (note 1, 2)

V

CC

(V)

3.3

T

A

Min. Typ. Max. Min. Max. Min. Max.

0.5 0.8

-0.8 -0.5

Dynamic High

V

IHD

Voltage Input

3.3 2.0

= 50 pF

C

L

(note 1, 3)
Dynamic Low

V

ILD

Voltage Input

3.3 0.8

(note 1, 3)

1) Worst case package.

2) Max number of outp ut s defined as (n). Data inp ut s are driven 0V to 3.3V, (n-1) outputs switc hi ng and one out put at GND.

3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (V
), f=1MHz.

(V

IHD

-40 to 85°C -55 to 125°C

ILD

Unit

V

), 0V to thresho l d

3/12

74LVX244

Table 8: AC Electrical Characteristics (Input tr = tf = 3ns)

Test Condition Value

= 25°C

Symbol Parameter

t

Propagation Delay

PLH

t

t
t

t
t

t

OSLH

t

OSHL

1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switch-

ing in the sa m e di rection, ei ther HIGH or LOW

2) Param eter guaran teed by design

(*) Voltage range is 3.3V ±

Time

PHL

Output Enable

PZL

Time

PZH

Output Disable

PLZ

Time

PHZ

Output to Output
Skew Time (note
1,2)

0.3V

V

C

CC

(V)

L

(pF)

2.7 15 6.1 11.4 1.0 13.5 1.0 15.0

2.7 50 8.6 14.9 1.0 17.0 1.0 18.0

(*)

3.3

3.3

15 4.5 7.1 1.0 8.5 1.0 9.5

(*)

50 7.2 10.6 1.0 12.0 1.0 13.0

2.7 15 7.1 13.8 1.0 16.5 1.0 17.5

2.7 50 9.6 17.3 1.0 20.0 1.0 21.0

(*)

3.3

3.3

15 5.5 8.8 1.0 10.5 1.0 12.

(*)

50 8.0 12.3 1.0 14.0 1.0 15.0

2.7 50 11.6 16.0 1.0 19.0 1.0 20.5

(*)

3.3

50 9.7 11.4 1.0 13.0 1.0 14.5

2.7 50 0.5 1.0 1.5 1.5

(*)

3.3

50 0.5 1.0 1.5 1.5

T

A

Min. Typ. Max. Min. Max. Min. Max.

Table 9: Capacitive Characteristics

-40 to 85°C -55 to 125°C

Unit

ns

ns

ns

ns

Test Condition Value

= 25°C

Symbol Parameter

C

C

C

Input Capacitance

IN

Output

OUT

Capacitance
Power Dissipation

PD

Capacitance

V

CC

(V)

3.3 4 10 10 10 pF

3.3 6 pF

= 10MHz

3.3

f

IN

T

A

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

19 pF

Unit

(note 1)

1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without

load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I

= CPD x VCC x fIN + ICC/8 (per c ircuit )

CC(opr)

4/12

Figure 3: Test Circuit

t

, t

PLH

PHL

, t

t

PZL

PLZ

t

, t

PZH

PHZ

TEST SWITCH

Open

V

CC

GND

74LVX244

CL =15/50pF or equivalent (i ncludes jig an d probe capac i tance)

= R1 = 1KΩ or equivalen t

R

L

= Z

R

of pulse generator (typically 50Ω)

T

OUT

Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle)

5/12

74LVX244

Figure 5: Waveform - Output Enable And Disable Time (f=1MHz; 50% duty cycle)

6/12

SO-20 MECHANICAL DATA

74LVX244

DIM.

A 2.35 2.65 0.093 0.104

A1 0.1 0.30 0.004 0.012

B 0.33 0.51 0.013 0.020
C 0.23 0.32 0.009 0.013
D 12.60 13.00 0.496 0.512
E 7.4 7.6 0.291 0.299
e 1.27 0.050
H 10.00 10.65 0.394 0.419
h 0.25 0.75 0.010 0.030
L 0.4 1.27 0.016 0.050
k0° 8° 0° 8°

ddd 0.100 0.004

MIN. TYP MAX. MIN. TYP. MAX.

mm. inch

0016022D

7/12

74LVX244

TSSOP20 MECHANICAL DATA

mm. inch

DIM.

MIN. TYP MAX. MIN. TYP. MAX.

A 1.2 0.047

A1 0.05 0.15 0.002 0.004 0.006

A2 0.8 1 1.05 0.031 0.039 0.041

b 0.19 0.30 0.007 0.012

c 0.09 0.20 0.004 0.0079

D 6.4 6.5 6.6 0.252 0.256 0.260

E 6.2 6.4 6.6 0.244 0.252 0.260

E1 4.3 4.4 4.48 0.169 0.173 0.176

e 0.65 BSC 0.0256 BSC

K0˚ 8˚0˚ 8˚

L 0.45 0.60 0.75 0.018 0.024 0.030

A2

A

A1

b

e

K

c

L

E

D

E1

PIN 1 IDENTIFICATION

8/12

1

0087225C

74LVX244

Tape & Reel SO-20 MECHANICAL

mm. inch

DIM.

MIN. TYP MAX. MIN. TYP. MAX.

A 330 12.992
C 12.8 13.2 0.504 0.519
D 20.2 0.795
N 60 2.362

T 30.4 1.197
Ao 10.8 11 0.425 0.433
Bo 13.2 13.4 0.520 0.528
Ko 3.1 3.3 0.122 0.130
Po 3.9 4.1 0.153 0.161

P 11.9 12.1 0.468 0.476

DATA

9/12

74LVX244

Tape & Reel TSSOP20 MECHANICAL DATA

mm. inch

DIM.

MIN. TYP MAX. MIN. TYP. MAX.

A 330 12.992

C 12.8 13.2 0.504 0.519

D 20.2 0.795

N 60 2.362

T 22.4 0.882
Ao 6.8 7 0.268 0.276
Bo 6.9 7.1 0.272 0.280
Ko 1.7 1.9 0.067 0.075
Po 3.9 4.1 0.153 0.161

P 11.9 12.1 0.468 0.476

10/12

Table 10: Revision History

Date Revisio n Description of Changes

27-Aug-2004 4 Ordering Codes Revision - pag. 1.

74LVX244

11/12

74LVX244

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of s uch inf ormati on nor for a ny infr ing eme nt o f p atent s or o ther ri ghts of third parti es wh ic h m ay r esul t from i ts use. No license is gr an ted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.

The ST logo is a registered trademark of STMicroelectronics

All other names are the property of their respective owners

© 2004 STMicroelectronics - All Rights Reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

www.st.com

12/12