Page 1
INTEGRATED CIRCUITS
74LVCU04A
Hex inverter
Product specification 1998 Jul 29
Page 2
Philips Semiconductors Product specification
74L VCU04AHex inverter
FEA TURES
•Wide supply voltage range of 1.2 V to 3.6 V
•In accordance with JEDEC standard no. 8-1A.
•Inputs accept voltages up to 5.5 V
•CMOS low power consumption
DESCRIPTION
The 74LVCU04A is a high-performance, low-power, low-voltage,
Si-gate CMOS device and superior to most advanced CMOS
compatible TTL families.
The 74LVCU04A is a general purpose hex inverter. Each of the six
inverters is a single stage with unbuffered outputs.
•Direct interface with TTL levels
QUICK REFERENCE DATA
GND = 0 V; T
SYMBOL
t
NOTES:
is used to determine the dynamic power dissipation(PD in µW)
1. C
PD
= CPD V
P
D
f
= input frequency in MHz; CL = output load capacity in pF;
i
= output frequency in MHz; VCC = supply voltage in V;
f
o
(C
L
2. The condition is V
ORDERING INFORMATION
14-Pin Plastic SO –40°C to +85°C 74LVCU04A D 74LVCU04A D SOT108-1
14-Pin Plastic SSOP Type II –40°C to +85°C 74LVCU04A DB 74LVCU04A DB SOT337-1
14-Pin Plastic TSSOP Type I –40°C to +85°C 74LVCU04A PW 74LVCU04APW DH SOT402-1
= 25°C; tr = tf 2.5 ns
amb
PARAMETER CONDITIONS TYPICAL UNIT
PHL/tPLH
C
I
C
PD
V
CC
Propagation delay
nA to nY
Input capacitance 7.8 pF
Power dissipation capacitance per gate Notes 1 and 2 16.8 pF
2
x fi (CL V
CC
2
fo) = sum of the outputs.
= GND to V
I
CC.
CC
2
fo) where:
CL = 50 pF;
VCC = 3.3 V
4.3 ns
PACKAGES TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA PKG. DWG. #
PIN CONFIGURATION
1
GND
1A
2
1Y
3
2A
4
2Y
5
3A
6
3Y
7
14
V
13
6A
12
6Y
11
5A
10
5Y
9
4A
8
4Y
SV00396
CC
PIN DESCRIPTION
PIN NUMBER SYMBOL NAME AND FUNCTION
1, 3, 5, 9, 11, 13 1A – 6A Data inputs
2, 4, 6, 8, 10, 12 1Y – 6Y Data outputs
7 GND Ground (0 V)
14 V
CC
Positive supply voltage
LOGIC SYMBOL (IEEE/IEC)
12
34
56
98
11 10
13 12
1
1
1
1
1
1
SV00398
1998 Jul 29 853–2099 19800
2
Page 3
Philips Semiconductors Product specification
SYMBOL
PARAMETER
CONDITIONS
UNIT
V
V
Hex inverter
LOGIC SYMBOL
1A 1Y
1
2A
3
5
3A 3Y
4A 4Y
9
11
5A 5Y
6A
13
2Y
6Y
SV00397
74LVCU04A
LOGIC DIAGRAM (ONE INVERTER)
V
2
4
nA nY
6
8
10
12
FUNCTION TABLE
INPUTS OUTPUTS
100
nA nY
L H
H L
NOTES:
H = HIGH voltage level
L = LOW voltage level
CCVCC
SV00409
RECOMMENDED OPERATING CONDITIONS
V
V
T
V
amb
tr, t
DC supply voltage (for max. speed performance) 2.7 3.6 V
CC
DC supply voltage (for low-voltage applications) 1.2 3.6 V
CC
DC input voltage range 0 5.5 V
I
DC output voltage range; output HIGH or LOW state 0 V
I/O
DC input voltage range; output 3-State 0 5.5
Operating free-air temperature range –40 +85 °C
Input rise and fall times
f
VCC = 1.2 to 2.7V
VCC = 2.7 to 3.6V
LIMITS
MIN MAX
CC
0
0
20
10
ns/V
1998 Jul 29
3
Page 4
Philips Semiconductors Product specification
V
V
mW
VOHHIGH level output voltage
V
IIInput leakage current
V
GND; Not for I/O pins
"0.1
"5µA
Hex inverter
ABSOLUTE MAXIMUM RATINGS
1
74LVCU04A
In accordance with the Absolute Maximum Rating System (IEC 134).
Voltages are referenced to GND (ground = 0V).
SYMBOL
V
CC
I
IK
V
I
I
OK
DC supply voltage –0.5 to +6.5 V
DC input diode current VIt 0 –50 mA
DC input voltage Note 2 –0.5 to +6.5 V
DC output diode current V
PARAMETER CONDITIONS RATING UNIT
uVCC or VO t 0 "50 mA
O
DC output voltage; output HIGH or LOW Note 2 –0.5 to VCC +0.5
I
GND
I/O
I
T
stg
DC input voltage; output 3-State Note 2 –0.5 to 6.5
DC output source or sink current VO = 0 to V
O
, I
DC VCC or GND current "100 mA
CC
CC
"50 mA
Storage temperature range –65 to +150 °C
Power dissipation per package
P
TOT
– plastic mini-pack (SO) above +70°C derate linearly with 8 mW/K 500
– plastic shrink mini-pack (SSOP and TSSOP) above +60°C derate linearly with 5.5 mW/K 500
NOTES:
1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability .
2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
DC ELECTRICAL CHARACTERISTICS
Over recommended operating conditions. V oltages are referenced to GND (ground = 0V).
SYMBOL PARAMETER TEST CONDITIONS
VCC = 1.2 V;VOL(max) = 0.5 V; IO = -100 mA
VCC = 2.0 V; VOL(max) = 0.5 V; IO = -100 mA
V
V
V
I
NOTE:
1. All typical values are at V
HIGH level Input voltage
IH
VCC = 2.7 V; VOL(max) = 0.5 V; IO = -100 mA
VCC = 3.0 V; VOL(max) = 0.5 V; IO = -100 mA
VCC = 3.6 V; VOL(max) = 0.5 V; IO = -100 mA
VCC = 1.2 V; VOH(min) = VCC – 0.5 V; IO = 100 mA
VCC = 2.0 V; VOH(min) = VCC – 0.5 V; IO = 100 mA
LOW level Input voltage
IL
VCC = 2.7 V; VOH(min) = VCC – 0.5 V; IO = 100 mA
VCC = 3.0 V; VOH(min) = VCC – 0.5 V; IO = 100 mA
VCC = 3.6 V; VOH(min) = VCC – 0.5 V; IO = 100 mA
VCC = 2.7 V; VCC or GND; IO = -12 mA VCC*0.5
p
VCC = 3.0 V; VCC or GND; IO = -100mA
VCC = 3.0 V; VCC or GND; IO = -12 mA VCC*0.6
VCC = 3.0 V; VCC or GND; IO = -24 mA VCC*1.0
VCC = 2.7 V; VCC or GND; IO = 12 mA 0.40
LOW level output voltage
OL
VCC = 3.0 V; VCC or GND; 12mA; IO = 100µA 0.20
VCC = 3.0 V; VCC or GND; IO = 24mA 0.55
p
Quiescent supply current VCC = 3.6 V; VCC or GND; IO = 0 0.1 10 µA
CC
= 3.3V and T
CC
CC
amb
= 25°C.
;
= 3.6 V; 5.5 V or
;
p
LIMITS
Temp = -40°C to +85°C
MIN TYP1MAX
V
CC
1.2
1.8
2.0
2.4
VCC*0.2 V
CC
GND
0.6
0.6
1.0
1.2
UNIT
V
V
V
1998 Jul 29
4
Page 5
Philips Semiconductors Product specification
Hex inverter
AC CHARACTERISTICS
GND = 0 V; tr = tf 2.5 ns; CL = 50 pF; RL = 500W; T
SYMBOL PARAMETER WAVEFORM
t
/
PHL
t
PLH
Propagation delay
nA to nY
NOTE:
1. These typical values are at V
= 3.3V and T
CC
amb
AC WAVEFORM
VM = 1.5 V at VCC 2.7 V
= 0.5 VCC at VCC < 2.7 V
V
M
V
and VOH are the typical output voltage drop that occur with the
OL
output load.
V
I
nA INPUT
GND
V
OH
nY OUTPUT
V
OL
Figure 1. Input (nA) to output (nY) propagation delays.
V
R
M
= 560 kW
bias
t
PHL
V
M
V
CC
= –40C to +85C
amb
Figure 1 – 2.7 4.3 – 5.3 – ns
= 25°C.
t
PLH
SV00395
74LVCU04A
LIMITS
VCC = 3.3V ±0.3V VCC = 2.7V VCC = 1.2V
MIN TYP
1
MAX MIN MAX TYP
80
g
fs
(mA/V)
60
40
20
10
0
01234
VCC (V)
SV00410
Figure 3. Typical forward transconductance gfs as a function of
at T
the supply voltage V
CC
amb
= 25C.
UNIT
100 mF0.47 mF
i
A
o ~
GND
SV00323
Vi ~
(f = 1 kHz)
input output
Figure 2. Test set-up for measuring forward transconductance
g
= dio/dvi at vo is constant (see also graph Figure 3).
fs
1998 Jul 29
5
Page 6
Philips Semiconductors Product specification
Hex inverter
APPLICATION INFORMATION
Some applications for the 74LVU04 are:
•Linear amplifier (see Figure 4)
•In crystal oscillator designs (see Figure 5)
•Astable multivibrator (see Figure 6)
R
2
V
CC
R
1 mF
1
U04
Note:
> 10kΩ; AOL = 20 (typical)
Z
L
Au+ –
3 kΩ < R1, R2 < 1 MΩ
Typical unity gain bandwidth product is 5 MHz.
Cl, see Figure10
AOL = open loop amplification
A
= voltage amplification
u
Figure 4. LVU04 used as a linear amplifier.
1 )
A
R
1
R
2
OL
(1 ) AOL)
;V
OMax(P*P)
V
CC
≈
at 1/2 V
– 1.5 V centered
74LVCU04A
R
1
R
2
Z
L
GND
U04
out
Note:
C
= 47 pF (typ.)
1
C
= 22 pF (typ.)
2
= 1 to 10 MW (typ.)
R
1
R
optimum value depends on the frequency and required stability against
2
changes in V
2 mA at V
or average minimum ICC (ICC is typically
CC
= 3 V and f = 1 MHz).
CC
Figure 5. Crystal oscillator configuration.
C
1
Note to Figure 5
C
= 47 pF (typ.)
1
C
= 22 pF (typ.)
2
R
= 1 to 10 MW (typ.)
1
R
optimum value depends on the frequency and required stability
2
against changes in V
CC
R
SV00404
S
or average minimum ICC.
CC
U04
R
U04
C
SV00408
C
2
Note to Figure 4
Z
> 10 kW; AOL = 20 (typical)
L
Au+ –
1 )
A
OL
R
1
(1 ) AOL)
R
2
; V
–
O Max (P
≈ VCC – 1.5 V centered
at 1/2 V
P)
CC
3 kW < R1, R2 < 1 MW
Typical unity gain bandwidth product is 50 MHz.
= open loop amplification
A
OL
= voltage amplification
A
u
1998 Jul 29
Note to Figure 6
1
f +
T
RS ≈ 2 x R
6
Note:
f +
RS[ 2xR
The average I
3.5 + 0.05 x f (MHz) x C (pF) at VCC = 3.0 V.
1
1
[
T
2.2 RC
(mA) is approximately
CC
SV00406
Figure 6. LVCU04 used as an astable multivibrator.
1
[
2.2 RC
Page 7
Philips Semiconductors Product specification
74LVCU04AHex inverter
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
1998 Jul 29
7
Page 8
Philips Semiconductors Product specification
74LVCU04AHex inverter
SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm SOT337-1
1998 Jul 29
8
Page 9
Philips Semiconductors Product specification
74LVCU04AHex inverter
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1
1998 Jul 29
9
Page 10
Philips Semiconductors Product specification
74LVCU04AHex inverter
Data sheet status
Data sheet
status
Objective
specification
Preliminary
specification
Product
specification
Product
status
Development
Qualification
Production
Definition
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1]
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury . Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
print code Date of release: 07-98
Document order number: 9397-750-04479
yyyy mmm dd
10
Loading...