Page 1
INTEGRATED CIRCUITS
74F64
4-2-3-2-input AND-OR-invert gate
Product specification 1996 Mar 14
IC15 Data Handbook
Page 2
Philips Semiconductors Product specification
74F644-2-3-2-input AND-OR-invert gate
PIN CONFIGURATION
TYPE
TYPICAL
PROPAGATION
DELA Y
TYPICAL
SUPPLY CURRENT
(TOTAL)
74F64 4.0ns 2.5mA
ORDERING INFORMATION
COMMERCIAL RANGE
DESCRIPTION
14-pin plastic DIP N74F64N SOT27-1
VCC = 5V ±10%,
T
= 0°C to +70°C
amb
PKG. DWG. #
GND
14-pin plastic SO N74F64D SOT108-1
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW
Dn Data inputs 1.0/1.0 20µA/0.6mA
Q Data output 50/33 1.0mA/20mA
NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
LOGIC SYMBOL
2 9 10
Da Db Dc Dd De Df Dg Dh Di Dj Dk
VCC = Pin 14
GND = Pin 7
3 1 13 12 11 4 5 6
Q
8
SF00095
IEC/IEEE SYMBOL
2
3
1
13
12
11
4
5
6
9
10
SF00094
1
14
V
CC
13
Dd
12
De
11
Df
Dk
10
Dj
9
87
Q
1
Dc
2
Da
3
Db
4
Dg
5
Dh
6
Di
&
&
8
&
&
SF00096
1996 Mar 14 853–0334 16574
2
Page 3
Philips Semiconductors Product specification
74F644-2-3-2-input AND-OR-invert gate
LOGIC DIAGRAM
2
Da
3
Db
1
Dc
13
Dd
12
De
11
VCC = Pin 14
GND = Pin 7
Df
4
Dg
5
Dh
6
Di
9
Dj
10
Dk
8
SF00097
Q
FUNCTION TABLE
INPUTS OUTPUT
Da Db Dc Dd De Df Dg Dh Di Dj Dk Q
H H X X X X X X X X X L
X XHHHHXXXXX L
X XXXXXHHHXX L
X XXXXXXXXHH L
All other combinations H
NOTES:
1. H = High voltage level
2. L = Low voltage level
3. X = Don’t care
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limits set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL
V
CC
V
IN
I
IN
V
OUT
I
OUT
T
amb
T
stg
1996 Mar 14
Supply voltage –0.5 to +7.0 V
Input voltage –0.5 to +7.0 V
Input current –30 to +5 mA
Voltage applied to output in High output state –0.5 to V
Current applied to output in Low output state 40 mA
Operating free-air temperature range 0 to +70 °C
Storage temperature range –65 to +150 °C
PARAMETER RATING UNIT
3
CC
V
Page 4
Philips Semiconductors Product specification
SYMBOL
PARAMETER
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
1
UNIT
VOHHigh-level output voltage
VOLLow-level output voltage
ICCSupply current (total)
V
MAX
74F644-2-3-2-input AND-OR-invert gate
RECOMMENDED OPERATING CONDITIONS
LIMITS
MIN NOM MAX
V
CC
V
IH
V
IL
I
IK
I
OH
I
OL
T
amb
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
V
IK
I
I
I
IH
I
IL
I
OS
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at V
3. Not more than one output should be shorted at a time. For testing I
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, I
Supply voltage 4.5 5.0 5.5 V
High-level input voltage 2.0 V
Low-level input voltage 0.8 V
Input clamp current –18 mA
High-level output current –1 mA
Low-level output current 20 mA
Operating free-air temperature range 0 +70 °C
LIMITS
2
MAX
0.30 0.50 V
0.30 0.50 V
–0.73 –1.2 V
p
p
VCC = MIN, VIL = MAX ±10%V
VIH = MIN, IOH = MAX ±5%V
VCC = MIN, VIL = MAX ±10%V
VIH = MIN, IOL = MAX ±5%V
Input clamp voltage VCC = MIN, II = I
Input current at maximum input
voltage
VCC = MAX, VI = 7.0V 100 µA
MIN TYP
CC
CC
CC
CC
IK
2.5 V
2.7 3.4 V
High-level input current VCC = MAX, VI = 2.7V 20 µA
Low-level input current VCC = MAX, VI = 0.5V –0.6 mA
Short-circuit output current
pp
= 5V, T
CC
3
VCC = MAX –60 –150 mA
I
CCH
I
CCL
= 25°C.
amb
tests should be performed last.
OS
CC
=
VIN = GND 1.9 2.8 mA
VIN = 4.5V 3.1 4.7 mA
, the use of high-speed test apparatus and/or sample-and-hold
OS
1996 Mar 14
4
Page 5
Philips Semiconductors Product specification
TEST
CONDITION
74F644-2-3-2-input AND-OR-invert gate
AC ELECTRICAL CHARACTERISTICS
LIMITS
VCC = +5.0V VCC = +5.0V ± 10%
SYMBOL PARAMETER
t
PLH
t
PHL
Propagation delay
Dn to Q
AC WAVEFORMS
For all waveforms, VM = 1.5V.
Waveform 1
T
= +25°C T
amb
= 0°C to +70°C UNIT
amb
CL = 50pF, RL = 500Ω CL = 50pF, RL = 500Ω
MIN TYP MAX MIN MAX
2.5
2.0
4.6
3.2
6.0
4.5
2.5
2.0
7.0
5.5
ns
Dn
Q
Waveform 1. Propagation Delay for Inverting Outputs
TEST CIRCUIT AND WAVEFORM
V
CC
V
PULSE
GENERATOR
IN
R
T
Test Circuit for Totem-Pole Outputs
DEFINITIONS:
R
= Load resistor;
L
see AC ELECTRICAL CHARACTERISTICS for value.
C
= Load capacitance includes jig and probe capacitance;
L
see AC ELECTRICAL CHARACTERISTICS for value.
R
= Termination resistance should be equal to Z
T
pulse generators.
D.U.T.
V
OUT
C
V
M
t
PHL
NEGATIVE
PULSE
R
L
L
POSITIVE
PULSE
V
M
t
PLH
90%
10%
V
M
SF00098
t
w
V
M
10%
)
V
90%
M
t
THL (tf
t
TLH (tr
)
t
t
t
w
TLH (tr
THL (tf
10%
)
)
90%
V
M
V
M
90%
10%
AMP (V)
0V
AMP (V)
0V
V
M
Input Pulse Definition
INPUT PULSE REQUIREMENTS
V
amplitude
3.0V 1.5V
rep. rate
M
1MHz 500ns
t
w
t
TLHtTHL
2.5ns 2.5ns
OUT
of
family
74F
1996 Mar 14
SF00006
5
Page 6
Philips Semiconductors Product specification
74F644-2-3-2 Input AND-OR Invert Gate
DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1
1996 Mar 14
6
Page 7
Philips Semiconductors Product specification
74F644-2-3-2 Input AND-OR Invert Gate
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
1996 Mar 14
7
Page 8
Philips Semiconductors Product specification
74F644-2-3-2-input AND-OR-invert gate
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICA TIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation
register eligible circuits under the Semiconductor Chip Protection Act.
Copyright Philips Electronics North America Corporation 1996
All rights reserved. Printed in U.S.A.
Loading...