Page 1
INTEGRATED CIRCUITS
74ALS153
Dual 4-input multiplexer
Product specification 1991 Feb 08
IC05 Data Handbook
Page 2
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
FEA TURES
PIN CONFIGURATION
•Non–inverting outputs
E
1
•Common select outputs
•Separate enable for each section
•See 74ALS253 for 3–State version
DESCRIPTION
The 74ALS153 has two identical 4–input multiplexer with 3–State
outputs which selects two bits of data from four sources by using
common select inputs (S0, S1). The two 4–input multiplexer circuits
have individual active–Low enables (E
strobe the outputs independently. Outputs (Ya, Yb) are forced Low
when the corresponding enable is high.
The 74ALS153 is the logic implementation of a 2–pole, 4–position
switch where the position of the switch is determined by the logic
levels supplied to the common select inputs.
TYPE
TYPICAL
PROPAGATION DELAY
74ALS153 7.0ns 6.5mA
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION
Ioa – I3a Port A data inputs 1.0/1.0 20µA/0.1mA
Iob – I3b Port B data inputs 1.0/1.0 20µA/0.1mA
S0, S1 Common select inputs 1.0/1.0 20µA/0.1mA
Ea Port A enable input 1.0/1.0 20µA/0.1mA
Eb Port B enable input 1.0/1.0 20µA/0.1mA
Ya, Yb Data outputs 130/240 2.6mA/24mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.
a, Eb) which can be used to
TYPICAL
SUPPLY CURRENT
(TOTAL)
ORDERING INFORMA TION
DESCRIPTION COMMERCIAL RANGE
16-pin plastic DIP 74ALS153N SOT38-4
16-pin plastic SO 74ALS153D SOT109-1
16-pin plastic SSOP
Type II
a
2
S1
3
I3a
4
I2a
5
I1a
6
I0a
Ya
74ALS (U.L.)
HIGH/LOW
ORDER CODE
V
= 5V ±10%,
CC
T
= 0°C to +70°C
amb
74ALS153DB SOT338-1
16
V
CC
b
15
E
S0
14
13
I3b
12
I2b
11
I1b
107
I0b
98GND Yb
LOAD VALUE
HIGH/LOW
SF00146
DRAWING
NUMBER
LOGIC SYMBOL
I1a I2a
43
I3aI0a
Ya
7
10 11
Yb
9
I1b I2b
12 13
I3bI0b
SF00147
65
14
2
1
15
V
= Pin 16
CC
GND = Pin 8
S0
S1
Ea
Eb
1991 Feb 08 853–1376 01670
IEC/IEEE SYMBOL
2
14
2
1
6
5
4
3
15
10
11
12
13
EN
0
0
G
3
1
MUX
0
1
2
3
7
9
SF00148
Page 3
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
LOGIC DIAGRAM
a EbI0a I1a I2a I3a S1 S2 I0b I0b I2b I3b
E
1 65432141011121315
= Pin 16
V
CC
GND = Pin 8
7
Ya Yb
9
FUNCTION TABLE
INPUTS OUTPUT
S0 S1 I0n I1n I2n I3n En Yn
L L L X X X L L
L L H X X X L H
H L X L X X L L
H L X H X X L H
L H X X L X L L
L H X X H X L H
H H X X X L L L
H H X X X H L H
H = High voltage level
L = Low voltage level
X = Don’t care
SF00149A
1991 Feb 08
3
Page 4
Philips Semiconductors Product specification
SYMBOL
PARAMETER
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
1
UNIT
VOHHigh-level output voltage
CC
,
IL
,
VOLLow-level output voltage
CC
,
IL
,
74ALS153Dual 4-input multiplexer
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL
V
I
T
V
V
I
OUT
OUT
amb
T
CC
IN
stg
Supply voltage –0.5 to +7.0 V
Input voltage –0.5 to +7.0 V
IN
Input current –30 to +5 mA
Voltage applied to output in high output state –0.5 to V
Current applied to output in Low output state 48 mA
Operating free-air temperature range 0 to +70 °C
Storage temperature range –65 to +150 °C
RECOMMENDED OPERATING CONDITIONS
V
T
CC
V
V
I
Ik
I
OH
I
OL
amb
Supply voltage 4.5 5.0 5.5 V
High-level input voltage 2.0 V
IH
Low-level input voltage 0.8 V
IL
Input clamp current –18 mA
High-level output current –2.6 mA
Low-level output current 24 mA
Operating free-air temperature range 0 +70 °C
PARAMETER RATING UNIT
CC
V
LIMITS
MIN NOM MAX
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
MIN TYP
p
p
V
I
I
IH
I
IL
I
O
I
CC
Input clamp voltage VCC = MIN, II = I
IK
Input current at minimum input
I
voltage
High-level input current VCC = MAX, VI = 2.7V 20 µA
Low-level input current VCC = MAX, VI = 0.4V –0.1 mA
Output current
3
Supply current (total) VCC = MAX 6.5 12 mA
VCC = ±10%, VIL = MAX,
VIH = MIN
VCC = MIN, VIL = MAX,
VIH = MIN
IK
VCC = MAX, VI = 7.0V 0.1 mA
VCC = MAX, VO = 2.25V –30 –112 mA
IOH = –0.4mA V
IOH = MAX 2.4 3.2 V
I
= 12mA 0.25 0.40 V
OL
I
= 24mA 0.35 0.50 V
OL
– 2 V
CC
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at V
3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, I
= 5V, T
CC
amb
= 25°C.
2
MAX
–0.73 –1.5 V
OS
.
1991 Feb 08
4
Page 5
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
AC ELECTRICAL CHARACTERISTICS
LIMITS
T
= 0°C to +70°C
amb
V
SYMBOL PARAMETER TEST CONDITION
t
t
t
t
t
t
PLH
PHL
PLH
PHL
PLH
PHL
Propagation delay
In to Yn
Propagation delay
Sn to Yn
Propagation delay
E
n to Yn
Waveform 1
Waveform 2
Waveform 2
AC WAVEFORMS
For all waveforms, VM = 1.3V.
= +5.0V ± 10%
CC
C
= 50pF, RL = 500Ω
L
MIN MAX
4.0
4.0
5.0
7.0
3.0
5.0
12.0
12.0
15.0
16.0
10.0
12.0
UNIT
ns
ns
ns
In
Yn
V
M
t
PLH
V
M
t
V
M
Waveform 1. Propagation Delay for Data to Output
TEST CIRCUIT AND WAVEFORMS
V
CC
V
PULSE
GENERATOR
IN
R
T
Test Circuit for Totem-pole Outputs
D.U.T.
V
OUT
C
L
PHL
Sn
V
En
V
M
SF00150
Yn
M
t
PLH
V
M
t
PHL
V
M
V
M
SC00046
Waveform 2. Propagation Delay for Select or Enable to Output
t
NEGATIVE
PULSE
R
L
POSITIVE
PULSE
90%
10%
V
M
10%
t
THL (tf
t
TLH (tr
90%
V
M
w
V
M
10%
)
f
)
t
)
TLH (tr
t
)
THL (tf
90%
V
M
t
w
90%
10%
AMP (V)
0.3V
AMP (V)
0.3V
DEFINITIONS:
R
= Load resistor;
L
see AC electrical characteristics for value.
CL= Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
R
= Termination resistance should be equal to Z
T
pulse generators.
1991 Feb 08
OUT
of
5
Family
74ALS
Amplitude
3.5V
Input Pulse Definition
INPUT PULSE REQUIREMENTS
V
M
1.3V
Rep.Rate
1MHz
t
w
500ns
t
TLHtTHL
2.0ns 2.0ns
SC00005
Page 6
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
1991 Feb 08
6
Page 7
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
1991 Feb 08
7
Page 8
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1
1991 Feb 08
8
Page 9
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICA TIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
1991 Feb 08
9
Loading...