The 2SC4225 is an NPN silicon epitaxial transistor designed for low
noise amplifier at VHF through UHF band.
It has large dynamic range and good current characteristics.
FEATURES
• Low Noise and High Gain
NF = 1.5 dB TYP.at VCE = 10 V, IC = 5 mA, f = 1 GHz
S21e 2 = 10 dB TYP.at VCE = 10 V, IC = 20 mA, f = 1 GHz
(reference value)
ABSOLUTE MAXIMUM RATINGS (TA = 25 ˚C)
Collector to Base VoltageVCB025V
Collector to Emitter VoltageV
Emitter to Base VoltageV
Collector CurrentI
Total Power DissipationP
Junction TemperatureT
Storage TemperatureT
CE012V
EB03.0V
C70mA
T160mW
j150˚C
stg–65 to +150˚C
ELECTRICAL CHARACTERISTICS (TA = 25 ˚C)
PACKAGE DIMENSIONS
in millimeters
2.1 ± 0.1
1.25 ± 0.1
2
0.65
+0.1
–0
0.3
0.3
0.65
1
2.0 ± 0.2
0.9 ± 0.1
PIN CONNECTIONS
1. Emitter
2. Base
3. Collector
3
Marking
0 to 0.1
+0.1
+0.1
–0
0.3
–0.05
0.15
CharacteristicsSymbolMIN.TYP.MAX.UnitTest Conditions
Collector Cutoff CurrentICB01.0
Emitter Cutoff CurrentIEB01.0
DC Current GainhFE4080200
Gain Bandwidth ProductfT4GHz
Output CapacitanceCob1.21.8pFVCB = 3 V, IE = 0, f = 1 MHz
Insertion Power GainS21e
Noise Figure
hFE Classifications
RankR2R3
MarkingR2R3
hFE40 to 120100 to 200
Document No. P11192EJ2V0DS00 (2nd edition)
Date Published February 1996 P
Printed in Japan
µ
AVCB = 10 V, IE = 0
µ
AVEB = 2 V, IC = 0
VCE = 3 V, IC = 20 mA, pulsed
VCE = 3 V, IC = 20 mA, f = 1 GHz
No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this
document.
NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a device described herein or any other liability arising
from use of such device. No license, either express, implied or otherwise, is granted under any patents,
copyrights or other intellectual property rights of NEC Corporation or others.
While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,
the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or
property arising from a defect in an NEC semiconductor device, customer must incorporate sufficient safety
measures in its design, such as redundancy, fire-containment, and anti-failure features.
NEC devices are classified into the following three quality grades:
“Standard“, “Special“, and “Specific“. The Specific quality grade applies only to devices developed based on
a customer designated “quality assurance program“ for a specific application. The recommended applications
of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each
device before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems or medical equipment for life support, etc.
The quality grade of NEC devices in “Standard“ unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
they should contact NEC Sales Representative in advance.
Anti-radioactive design is not implemented in this product.
M4 94.11
8
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.