Datasheet 24MP76HM Service manual (LG)

r

Internal Use Only

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

COLOR MONITOR

SERVICE MANUAL

CHASSIS NO. : LM13C

MODEL: 24MP76HM

CAUTION

BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL62449312 (1310-REV00) Printed in Korea

CONTENTS

CONTENTS .............................................................................................. 2

PRECAUTION............................................................................................3

SERVICING PRECAUTIONS.....................................................................4

SPECIFICATIONS......................................................................................6

TIMING CHART .......................................................................................11

ADJUSTMENT .........................................................................................14

BLOCK DIAGRAM...................................................................................18

TROUBLE SHOOTING ............................................................................19

EXPLODED VIEW .................................................................................. 22

SVC. SHEET ...............................................................................................

- 2 -

LGE Internal Use Only

PRECAUTION

WARNING FOR THE SAFETY-RELATED COMPONENT.

• There are some special components used in LCD monitor that

are important for safety. These parts are marked on the schematic diagram and the Exploded View. It is essential that these critical parts should be replaced with the manufacturer’s specified parts to prevent electric shock, fire or other hazard.

• Do not modify original design without obtaining written permission from manufacturer or you will void the original parts and labor guarantee.

TAKE CARE DURING HANDLING THE LCD MODULE WITH BACKLIGHT UNIT.

• Must mount the module using mounting holes arranged in four corners.

• Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.

• Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to the panel.

• Protect the module from the ESD as it may damage the electronic circuit (C-MOS).

WARNING

BE CAREFUL ELECTRIC SHOCK !

• If you want to replace with the new backlight (CCFL) or LIPS part, must disconnect the AC power because high voltage appears at inverter circuit about 650Vrms.

• Handle with care wires or connectors of the inverter circuit. If the wires are pressed cause short and may burn or take fire.

Leakage Current Hot Check Circuit

AC Volt-meter

Good Earth Ground such as WATER PIPE,

To Instrument's exposed METALLIC PARTS

When 25A is impressed between Earth and 2nd Ground for 1 second, Resistance must be less than 0.1

*Base on Adjustment standard

0.15uF

1.5 Kohm/10W

CONDUIT etc.

Ω

• Make certain that treatment person’s body are grounded through wrist band.

• Do not leave the module in high temperature and in areas of high humidity for a long time.

• The module not be exposed to the direct sunlight.

• Avoid contact with water as it may a short circuit within the module.

• If the surface of panel become dirty, please wipe it off with a softmaterial. (Cleaning with a dirty or rough cloth may damage the panel.)

CAUTION

Please use only a plastic screwdriver to protect yourself from shock hazard during service operation.

- 3 -

LGE Internal Use Only

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service

manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication.

NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or re-connecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) is opropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500ºF to 600ºF.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500ºF to 600ºF) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500ºF to 600ºF)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 4 -

LGE Internal Use Only

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete TransistorRemoval/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

- 5 -

LGE Internal Use Only

SPECIFICATIONS

1. General Specification

No Item Criteria Remark

1 Customer BRAND 2 User Model Name 24MP76HM 3 Sale region Refer to Suffix standard 4 Feature 23.8” Wide LCD MONITOR 5 Chassis Name LM13C

General Scope

6

7

8 Cable

External SW

&Adj.

Function OSD,DDC2B,DDC2AB, HDCP, Control Lock,

Power Cord

Signal Cable

(D-SUB)

DVI

Menu, My-Key , Function, Auto, input/Exit, Power

Original Ratio / Wide, Black level, Super Energy Saving

Length : 1.5±0.05 M Shape : Wall-out Color : Black

Length : 1.5m Shape : Detachable Type Color : Black Pin : Triple Row, 15 Pin D-Sub

Length : 1.5m Shape : Detachable Type Color : Black Pin : Triple Row, 18-Position DVI-D

standard and power

Refer to Suffix

Do not Support

Refer to Suffix

cord table

standard

Audio

TV Length : ,Shape : ,Color: ,Pin Do not Support

9 Power

10 Applying module list

Length : 1.5 Color: Black , Pin:2P

Input: AC100~240V 50~60Hz,1.0A Max Output: DC 19V 1.7 A

P/No Specification

EAJ62469601

LM238WF2-SSC1

Do not Support

Refer to Suffix

standard

- 6 -

LGE Internal Use Only

2. Mechanical specification

No Item Criteria Remark

1

Product

Dimension

Before Packing

After

Width (W) Length (D) Height (H)

54cm 18.1cm 42.9cm With stand 54cm 7.5cm 32.2cm Without stand

64.7cm 39.2cm 12.7cm

Packing

2

3

Product

Weight

Container

Loading

Quantity

4 Stand

Assy

Only SET 4.3kg

With BOX 5.6kg

Individual or Palletizing

20ft 40ft

Indi. Pallet Indi. Pallet

W/Wide

(NON EU)

- 640 - 1672

Type Base detachable

Size (W x

17.4cm x 15.5cm x 12cm Only stand base D x H)

Tilt Degree -5°(+/-3°) ~ 20°(+/-3°)

Tilt force 0.8~1.2 kgf

Folding

None

Degree

5 Appearance General Refer to Standard of LG(56)G2-1011

3. Optical Character

No Item Criteria Remark

1

2

3

Viewing Angle <CR≥10>

Luminance(휘도)

Contrast Ratio(명암 비)

4 Response Time Gray to Gray: 5ms(Average),

Reader 1

Reader 2

5

Paper Mo

de

Horizontal(R/L) : 178º ( (Typ.)

Vertical(Top/Bottom) : 178º (Typ.)

Average Luminance (cd/m

Super Energy Sa ving On

Luminance Uniformity

200(min), 250 (Typ.)

2

)

(Full white pattern, 0.7V)

150 (min)

2

)

(Full white pattern, 0.7V)

150(min)

2

)

(Full white pattern, 0.7V)

Low: >=2W/h down from S-Energy Saving Off. High:>=4W/h down from S-Energy Saving Off

75%(min),

600(MIN), 1000(TYP), DFC->5,000,000:1(Typ.)

X:

0.3650 ± 0.0

15

X:

0.3530 ± 0.0

15

Y: 0.3605 ± 0.0

15

Y: 0.3670 ± 0.0

15

Luminance(cd/ m2): 80 ± 20

Contrast Ratio:

(60 ~ 100:1)

Contrast Ratio:

(60 ~ 100:1)

Warm (6500K)

Medium (8000K)

Cool (9300K)

- 7 -

LGE Internal Use Only

4. Engineering Specification

1

Supported Sync. Type

Separate Sync., Digital

Analog

2 Operating Frequency

HDMI

Analog

3 Resolution

HDMI

Horizontal 30  83kHz Vertical 56  75 Hz Horizontal 30  83kHz Vertical 56  61 Hz Max. 1920×1080 @ 60Hz Recommend 1920×1080 @ 60Hz Max. 1920×1080 @ 60Hz Recommend 1920×1080 @ 60Hz

4 Input Voltage Voltage :100 – 240 Vac, 50 or 60Hz, 1.0A

5 Inrush Current Cold Start : 50 A Hot : 120 A

6

Operating Condition

On Mode On/On Active

Sync (H/V)

Video LED Wattage

white

（After 15s, the LED will be of

f）

Typ:26W Max:29W

Test condition

1.1920x1080@60Hz

2. burst pattern

3. 100~240V

4. After aging 30min

LED灯15s后会关掉

측정방법) 제어판 Æ 전원 옵션에서 디스플 레이 끄기와 PC를 절 전모드로 하기 두가지 설정이 있는데, PC를

Sleep Mode

Off/On On/Off Off/Off

Off white Blinking <0.3W

절전모드로 하기만 선 택하고 측정해야 함.

Off Mode

(Power switch off)

Super Energy

Saving

7

MTBF

- - Off <0.3W

Off/Lo

w/High

Low/Hig

h

3 0,000 HRS with

white

Efficiency : Low:>=2W/h

High:>=4W/h

Lamp Life : 30,000 Hours(Min)

90%

-T e st Conditi on (1)

Confidence level

8

Using Altitude

5,000 m (for Reliability) 3,000m(for FOS)

9

Environ

ment

Conditio

0peratin

g

Storage

n

MENU

OSD

MENU

(Monitor block)

Temperature

10 °C ~ 35 °C Humidity 10% ~ 80% Temperature

-20 °C ~ 60 °C

Humidity 5% ~ 90% non-condensing

Contrast 0~100

Volume 0~100

BRIGHTNESS 0 ~ 100

WARM

COLOR TEMP

PRESET

MEDIUM

COOL

USER RED

17 Language: English, Germanic, French, Spanish, Italian, Swedish, Finnish, Portuguese Brazilian Portuguese, Polish, Russian,

- 8 -

LGE Internal Use Only

GREEN Greek, Chinese,

Japanese, Korean, Ukrainian

Hindi

ORIGINAL

RATIO

BLUE

WIDE

ORIGINAL

▶ HIGH / LOW

BLACK LEVEL

(BLACK LEVEL enable at HDMI

input)

LANGUAGE

FACTORY

RESET

▶ ENGLISH

▶ NO( /YES )

CHANNEL 2~69(AIR) / 1 ~ 125(CABLE)

CHANNEL

ADD/DEL CH ADD/DELETE

AUTO CHANNEL ON/OFF

Function Support: No

SELECT AIR/CABLE

FINE TUNE 0 ~ 100

CONTRAST 0~100

ADJUSTMENT

BRIGHTNES S

SHARPNESS 0~10

0~100

Function Support: No

COLOR 0~100

MENU (AV/TV block)

AUDIO

TINT 0~100

VOLUME 0~100

BASS 0~100

TREBLE 0~100

MUTE ON/OFF

Function Support: No

SOUND

MONO/STEREO LANGUAGE▶

English/German/French/Esperanto Italian/Korean…

SETUP

IMAGE SIZE ▶ FULL/1:1

Function Support: No

OSD POSITION

TRANSPAREN CY

0~100

- 9 -

LGE Internal Use Only

5. Applying module Character

No Item Criteria Remark

Maker LGD

Type TFT

Active Display Area 23.8 inches(60.47cm) diagonal

LCD Module

1

Feature

Pixel Pitch [mm] 0.2745mm x 0.2745 mm.

Electrical Interface 2ch-LVDS

Color Depth 6-bit with A-FRC, 16.7M colors

Size (Outline) [mm] 535(H) x 313(V) x12.2(D) mm(Typ.)

Surface Treatment

Hard coating(3H),Anti-glare treatment of the front polarizer

Operating Mode Transmissive mode, normally Black

Back light Unit White LED

R/T

Typical 14ms

Max. 25ms

Minimum Normal Maximum

W

White

Coordinates

2

CIE Color

Red

Green

Blue

(1) Standard Measurement Condition

• Ambient Luminance Level : dark ( < 10 lux)

• Ambient Temperature : Normal Temperature(10ºC ~ 25ºC)

• warm-up Time : More than 30 min (at Full White Pattern)

• Input Signal : VESA 1920 X 1080 @ 60 Hz

• Contrast : 70 (But, the contrast is 100 when we check response time)

• Brightness : Max. 100

• Color Temp : CUSTOM

• Clock/Clock Phase : The Best Setting (2) Another Spec.: Product Specification Standard( LG(55)G1-1034 ) (3) Cosmetic Spec. : LCD Module IIS Spec.

X

WY 0.298

W

X

WY 0.310

WX

WY 0.329

R

X

RY 0.334

0.309

G

X

GY 0.627

0.153

B

X

BY 0.073

Typ-0.03

0.283

0.301

0.313

0.638

Typ-0.03

Typ+0.03

Cool

(9300K)

Medium (8000K)

Warm

(6500K)

Warm

(6500K)

5.1 Display Area

1) Active Display Area of the LCD Monitor Should be within Cabinet’s Bezel.

2) Distance Difference between Active Area and Bezel | A-B|<1.0 mm , | C-D|<1.0 mm

A: The Distance from The Left of Active Area to the Bezel B: The Distance from The Right of Active Area to the Bezel C: The Distance from The Top of Active Area to the Bezel D: The Distance from The Bottom of Active Area to the Bezel

Only for training and service purposes

- 10 -

C

Active area

A

A A B

Bezel

D

LGE Internal Use Only

6. EDID

6.1 24MP76HM

No Item Conten

1 Manufacturer ID GSM 1E 6D

2 Produ

ct ID

3 Year 2013 4 Version 1 01

5 Revision

6 Serial Number * *

7 Week ** ** 8 Model Name 24MP76 -9 Check Sum **** ****

10 Special Item Need to Input Serial Number

** Protocol : DDC 2AB

6.2 EDID Ver. 1.3 FOR ANALOG

t

16진 Data

(Analog) 23079 (27 5A)

(HDMI) 23080 (28 5A)

Analog : 3

HDMI : 3

03

6.3 EDID Ver. 1.3 FOR HDMI 1 (256Byte)

Only for training and service purposes

- 11 -

LGE Internal Use Only

(1) Signal(Video & Sync)

Video

Sync

TIMING CHART

C

B

DE

F

A

(2) H/V Timing

DOT Frequency To ta l Front Back

CLASSIF Polar Display Sync. Resolut

MODE CLOCK [kHz]/ Period Porch Porch

ICATION ity (A) (C) ion

[MHz] [Hz] (E) (D) (B)

H(Pixels) - 31.468 900 720 18 108 54

1 28.321

V(Lines) + 70.08 449 400 12 2 35

H(Pixels) - 31.469 800 640 16 96 48

2 25.175

V(Lines) - 59.94 525 480 10 2 33

H(Pixels) - 37.5 840 640 16 64 120

3 31.5

V(Lines) - 75 500 480 1 3 16

H(Pixels) + 37.879 1056 800 40 128 88

4 40.0

V(Lines) + 60.317 628 600 1 4 23

H(Pixels) + 46.875 1056 800 16 80 160

5 49.5

V(Lines) + 75.0 625 600 1 3 21

H(Pixels) - 48.363 1344 1024 24 136 160

6 65.0

V(Lines) - 60.0 806 768 3 6 29

H(Pixels) + 60.023 1312 1024 16 96 176

7 78.75

V(Lines) + 75.029 800 768 1 3 28

H(Pixels) + 108.0 67.500 1600 1152 64 128 256

8

V(Lines) + 75.000 900 864 1 3 32

H(Pixels) + 63.981 1688 1280 48 112 248

9 108.0

V(Lines) + 60.02 1066 1024 1 3 38

10 135.0

H(Pixels) + 79.976 1688 1280 16 144 248

V(Lines) + 75.035 1066 1024 1 3 38

720 X

400

640 x

480

640 x

480

800 x

600

800 x

600

1024 x

768

1024 x

768

1152 x

864

1280 x

1024

1280 x

1024

11 146.25

H(Pixels) - 65.290 2240 1680 104 176 280

V(Lines) + 59.954 1089 1050 3 6 30

H(Pixels) + 67.50 2200 1920 88 44 148

12 148.50

V(Lines) + 60 1125 1080 4 5 36

z D-SUB/DVI DTV Mode is not supported (interlace mode)

Only for training and service purposes

- 12 -

1680 x

1050

1920 x

1080

LGE Internal Use Only

(3) HDMI Timing

Factory support

mode

(Preset Mode)

Horizontal

frequency

(KHz)

Vertical

frequency

(Hz)

HDMI

1 480P 31.5 60 O

2 576P 31.25 50 O

3 720P 37.5 50 O

4 720P 45 60 O

5 1080i 28.12 50 O

6 1080i 33.75 60 O

7 1080P 56.25 50 O

8 1080P 67.5 60

(Recommend Mode)

O

- 13 -

LGE Internal Use Only

ADJUSTMENT

1. Coverage

Apply to 58.4

Gumi Korea) or made in accordance with the standard of Gumi Factory process.

cm (23 inch)

Wide monitor made in Monitor Factory

2. Appointment

2.1 Adjustment must be done as fixed sequence, and adjustment sequence can be modified after agreement withthe responsible R&D engineer considering mass-production condition.

2.2 Power : AC 100 - 240 Voltage (Free)

2.3

Input signal:

2.3.1 RGB Input: As Product Standard (Signal ROM : LB800K

Ver1.6)

2.3.2 RJ-45 input : As Product Standard (Ethernet connection

through network from Host PC)

* PC spec for MK(Minikey) Loader (TBD): CPU - Dual core 2.0

GHzD, Memory - 2 GByteD *PC spec for Host PC (TBD): CPU - Dual core 2.0 GHzD, Memory - 2 GByteD

2.4 Warm-up Time: Over than 30 minutes

2.5 Adjustment Display adjust equipment, VG-813(or VG819), Oscilloscope, PC (More than 486 program.

equipment : White balance equipment (CA-110),

computer ) & White balance adjust

3. Adjustment

3.1 Overview

Use factory automation equipment and adjust automatic

movement. But, do via passivity adjust in erroroccurrence.

PC audio volume : MAX * LAN cable * Router * PC: vSpace S/W for N+ ( Ver 4.5.xx.xx ) --- Caution: Ver

4.4.xx.xx for N1742L family

3.2.2 Total Assembly Line

· Ready : Heat-run during5 minutes in the state with signal

· Connect input signal to D-sub.

· Default value before adjustment : Contrast “70” , Brightness ‘100(Max)”

3.2.3 Adjustment of Horizontal/Verticality screen position, Clock and Clock Phase at each Mode.

· There is no special factory mode adjustment. Writing initial value of EEPROM in Board Assembly line is adjusting Preset Mode and Reset mode. (EEPROM is initialized when AC Power is ON first.)

· If the change of FOS data is needed after M.P, it is possible by writing Mode Data with EEPROM write command or modifying the Mode Data in MICOM itself.

3.2.4 Color coordinates adjustment and Luminance

adjustment.

3.2.4.1 Color coordinates adjustment

· Monitor Contrast / Brightness

- Contrast : 70

- Brightness : 100(Max)

· CA-110: Set “channel 9”

· Signal Generator : At cut-off and drive --> 16 step pattern for ADC (Program No.: 31)

- Output Voltage : 700 mVp-p

- Output Mode : Mode 12 (SXGA 60 Hz)mode Setting.

3.2 Adjustment order

(refer to the Adjustment standard and adjustment command table)

3.2.1 Board Assembly Line

3.2.1.1 15pin D-sub (RGB)

· Connect input signal to 15pin D-sub.

· Check the firmware version & model name. And write the firmware code to the serial Flash ROM by ISP.

· Ready for adjustment : check whether adjustment command works normally or not and the operating state of each mode.

· Check the display state of gray color when 256 gray scale patterns is embodied.

· Read by EEPROM Read Command to check whether initial value is correct or not.

3.2.1.2 MK( Minikey ) Loading

· Open MK Loader Tool on MK Loader PC.

( * MK Loader PC should be connected Internet)

· Connect input signal to RJ-45 input with LAN cable connected network devices such as routers.

· Turn on the Monitor set.

· Click the box when the °∞empty port °∞box is changed to “write mini-key” in MK Loader Tool.

3.2.1.2 RJ-45 input

· Connect input signal to RJ-45 input with LAN cable connected network devices such as routers.

· Check USB 1.1 Port (Keyboard/ Mouse) : @RJ-45 input

· Check USB 2.0 Port (USB Memory Stick 2port) : @RJ-45 input

· Check Audio (Ear-phone out/ Mic in/ Speaker) : @RJ-45 input,

3.2.4.2.Adjustment : Board Assembly Line

· Select RGB mode 16 step pattern for ADC (Program No.31 (Mode 12,Pattern

· Input

11)). (Video level : 700 mVp-p)

· Adjust by commanding AUTO_COLOR_ADJUST

· Confirm “Success” message in Screen or Check the data of 0xFE, 0xFF address of EEPROM(0XA6) is 0xAA after waiting 5 seconds.

· If there is “FAULT” message or the data of 0xFE, 0XFF address of EEPROM(0xA6) is not 0xAA, do adjust again.

· If all Adjustment is completed, the values of 6500K, User Color and 9300K are saved automatically.

· Select RGB mode

· Input 16 step pattern for ADC (Program No.31 (Mode 12,Pattern

11)). (Video level : 700mVp-p)

· Adjust by commanding AUTO_COLOR_ADJUST

· Confirm “Success” message in Screen or Check the data of 0xFE,0xFF address of EEPROM(0xA6) is 0xAA after waiting 5 seconds.

3.2.4.3. Confirm at Total Assembly Line: adjustment

· Check the data of 0xFE, 0xFF address of EEPROM(0xA6) is 0xAA.

· If the data of 0XFE, FF address of EEPROM(0xA6) is not 0xAA, do adjust again by 3.2.4.2.

- 14 -

LGE Internal Use Only

3.2.4.4. Confirm PRESET 6500K Color coordinates and Adjust PRESET 9300K Color coordinates .

· Set as Aging mode ON, by commanding AGING_ON/OFF command code.

· Select Module that is being used in present production by commanding MODULE SELECT. ( It is not needed so far. However, it will be needed to apply other modules)

· Send SYSTEM RESET command to set Module data.

· Input Full White Pattern (Video level : 700 mVp-p)

· Set as 9300K by commanding COLOR_MODE_CHANGE Command code.

· Check to meet x = 0.283 ± 0.03, y=0.298 ± 0.03, and confirm.

· Only if it does not meet, adjust as below steps.

· Adjust to meet x = 0.283 ± 0.01, y=0.298 ± 0.01 in 5 minutes. and confirm.

· Save 9300K Color by commanding COLOR SAVE Command code.

· Set as 6500K by commanding COLOR_MODE_CHANGE Command code.

· Check to meet x = 0.313 ± 0.03, y=0.329 ± 0.03, and confirm.

· Only if it does not meet, adjust as below steps.

· Adjust to meet x = 0.313 ± 0.01, y =0.329 ± 0.01, and confirm.

· Save 6500K Color by commanding COLOR SAVE Command code.

· Set as sRGB by commanding COLOR_MODE_CHANGE Command code.

· Adjust to meet Y = 150 ± 50, and confirm.

· Save sRGB Color by commanding COLOR SAVE Command code.

3.2.4.5. Confirm User color coordinates .

· Confirm Whether User color is saved same as 6500K.

· After confirming Color coordinates, Must return to 6500K

3.2.5 Confirm Operation state.

3.2.5.1 Operation mode : Confirm whether each appointed mode operate correctly or not.

3.2.5.2 Confirmation of Adjustment condition and operation : Confirm whether it meet Auto/Manual equipment Adjustment standard or not.

· Confirm Analog screen state : Confirm screen state at below mode.

Appointment mode (RGB input):

640*480 @60Hz (Mode 1), 800*600@75Hz(Mode 5), 1024*768@60Hz(Mode 8), 1280*1024@60Hz(Mode 12),

SMPTE pattern(Check 0%,5%,95%,100%)

–Mode can be added.

3.2.5.3. Confirm Auto adjustment operation.

· Input Analog 1 Dot on/off & Rectangle Pattern at Mode 12(1280x1024@60 Hz)

· Confirm adjustment operation by changing Clock, Phase, H/V Position.

· Check Clock, Phase by pressing AUTO Key.

· Confirm first set of new lot by periods

3.2.5.4 Other quality

· Confirm that each items satisfy under standard condition that was written product spec.

· Confirm Applying Module & MICOM Setting --> Confirm with Service OSD

- Confirm at Service OSD by “Menu + Power key” on .(from Power off)

- Confirm first set of new lot by periods, and confirm periodically

when there is Process change or Adjustment setting change.

3.2.5.5. OSD & Adjustment device Confirmation : Confirm operation mentioned as product spec.

· Vary Brightness and Contrast and confirm the variation of Luminance and display status.

· Operate the f-engine function and confirm variation of Luminance.

· Make sure to do FACTORY RESET after confirmation of OSD function.

3.2.5.6. Confirm the display state by inputting 8 color Bar Pattern & 256 Gray Scale pattern.

3.2.5.7. DPM operation confirmation : Check if Power LED Color and Power Consumption operates as standard.

· Measurement Condition : 230 V@ 50 Hz (Analog)

· Confirm DPM operation at the state of screen without Video Signal.

3.2.5.8. RJ-45 input

· Connect input signal to RJ-45 input with LAN cable connected network devices such as routers.

· Check USB 1.1 Port (Keyboard/ Mouse) : @RJ-45 input

· Check USB 2.0 Port (USB Memory Stick 2port) : @RJ-45 input

· Check Audio (Ear-phone out/Mic in/Speaker) : @RJ-45 input, PC audio volume : MAX

* LAN cable * Router * PC: vSpace S/W for N+ ( Ver 4.5.xx.xx ) --- Caution: Ver

4.4.xx.xx for N1742L family

3.2.5.9. DDC EDID Write ( Set as Aging mode ON, by commanding AGING_ON/OFF command code. )

1) SUFFIX: xxxxxPN

· Connect analog Signal Cable to D-sub wafer.

· Write EDID DATA to EEPROM(24C08) by using DDC2AB protocol.

· Check whether written EDID data is correct or not. (refer to Product spec).

--> After writing EDID, send Elapsed Time Clear command. (Elapsed time should not be displayed, after EDID writing) : Confirm periodically (in the first set of new lot, process change)

whether module name and aging time disappeared on the selfdiagnostics OSD with signal cable disconnected.

--> If Elapsed Time Clear command isn°Øt executed, module name, aging time and TCO word appear on the self-diagnostics OSD.(Module name and aging time should not appear after writing EDID)

--> Make sure to do FACTORY RESET at the final process.

3.2.5.10. Shipping condition

· Contrast : 70

· Power Switch : Off

· Brightness : “100(Max)”

· Color Select : Preset ( 6500K )

· Language Select : Refer to product spec.

· OSD Position : Center

· Power indicator : ON

· Flatron f-engine : Normal

- 15 -

LGE Internal Use Only

4.Standard of Auto/Manual equipment adjustment

No. Item Adjustment & measurement

standard

1 Voltage(V) 12 V± 0.6 V

5V± 0.3V / 3.3V± 0.25V

2 Color

coordinates

(9300/6500K)

Color

3

coordinates

(6500K)

Color

coordinates

(9300K)

Luminance 6500K More than

Position

5 Screen

Compensation

6 DPM

Confirmation

(RGB/LAN)

7

8 Withstanding Voltage

9

10 Cutoff /ADC Adjustm ent Pattern

11 Network Test with PC

Gray scale Confirmation Linear gray Scale MODE 12 Pattern 9 Full screen

confirmation

Ground Confirmation

Black Level

DRIVE1

DRIVE2

H 4 Screen

V

CLOCK

PHASE

AUTO FULL SIZE MODE

Normal Mode 40W(Typ) Pattern 4 Blue

Stand By Mode 1W/- Pattern 6

Suspend Mode 1W/- Pattern 7 Flicker

DPMS Off 1W/15W Pattern 8 Flicker

Power Switch

Off

2.5V± 0.2V

Auto Adjustment MODE 12 Pattern 0

u uí= 0. 198 ± 0.00 5

v ví=0.468± 0.005

X

Y

220 cd/m2

FULL SIZE MODE

When 1500Vac or 2121Vdc is

impressed between the first of

power (Live/Neutral) and

ground (Earth) for 1 second,

check whether something

wrong happens or not.

When 25A is impressed

between Earth and 2nd Ground

for 1 second, Resistance must

be less than 0.1

1280*1024@60Hz (700mVp-p)

CPU : Dual core 2.0 GHz

Memory : 2 GByte

Teradiciís PCoIP Host Card

LAN cable

0.283± 0.004

0.298± 0.004

FULL SIZE

1W

16 step pattern for ADC

,

Operation

mode

MODE 13 Pattern4

MODE 12 Pattern1

MODE 12

(700 mVp-p)

MODE

1 - 13

12-13

MODE 12

MODE 12 Pattern11

,

1280 * 1024

Operation

Pattern

Pattern1

Pattern4 Full Screen

Pattern 4

Measurement

Position

Each power

of Screen

Full screen

TP of

Center

Flicker

off

*Check items No. 2, 3, 4, 5 and 7 at RGB input.

- 16 -

LGE Internal Use Only

5. Pattern for Adjustment

Pattern 0 : FULL BLACK (State of without video signal ) Pattern 1 : FULL WHITE (Don’t display other Character except for White Pattern) Pattern 3 : FULL WHITE Pattern 4 : Cross hatch pattern (Horizontal 10Line, Vertcial 8Line) & Rectangle Pattern Pattern 5 : 1 Dot on, 1 Dot off & Rectangle Pattern Pattern 6 : Vertical Sync only input (Use signal cable of which Pin #5 is GND) Pattern 7 : Horizontal Sync only input (Use signal cable of which Pin #5 is GND) Pattern 8 : State of without Vertical/Horizontal Sync and Video Signal. (Use signal cable of which Pin #5 is GND) Pattern 9 : 8 Color Bar Pattern + 16 Gray Level Pattern Pattern 10 : SMPTE Pattern Pattern 11 : 16 Gray Step Pattern (700mV)

- 14 -

LGE Internal Use Only

F/B

F.HD)

(Blade5

LED PANEL

BLOCK DIAGRAM (Main)

AMP

0BW

STA38

(ST Micro)

IIC

LK

AMP

MC

V_LED

LVDS

Block

Embedded

LED Driver

(Novatek)

NT68773H

I

0B

PCM18

I

(TI)

Speak

S

ADC

er

HP

Aud

LED

SPI

L/R

io

(RE

Data/

out

IN

Key

D)

4M

CLK

IIC

SERIAL

H/

Flash

P

FUNCTION/AUTO/INPUT(Exit)

6 Keys : Power/MENU/MY KEY/

19V

From

Adapter

5VS

LED B/L

HDMI

02

24C

Amp

Audio

IIC

19-to-5V

HDMI_TMDS

24C

HDMI 2

T-Con

DC/DC

IIC

HDMI

02

HDMI_TMDS

5V

IIC

RGB

HDMI1

H/V

R/G/B/

RGB

3.3V

System

3.3V AMP

Core

1.2V

2Ch. LDO

- 15 -

LGE Internal Use Only

TROUBLESHOOTING GUIDE

1. NO POWER

- 16 -

LGE Internal Use Only

2. NO RASTER (OSD IS NOT DISPLAYED) – MAIN

- 17 -

LGE Internal Use Only

3. TROUBLE IN DPM

- 18 -

LGE Internal Use Only

540

EXPLODED VIEW

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

920

900

400

910

810

800

820

120

500

200

300

PDF created with pdfFactory Pro trial version www.pdffactory.com