Datalogic Scanning 1400I User Manual
Magellan® 1400i
Omni-Directional Imaging Scanner
Product Reference Guide
Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described
therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic
Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are
hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's
own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright
notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com)
or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this
or other Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice.
Datalogic is a registered trademark of Datalogic S.p.A. and the Datalogic logo is a trademark of Datalogic S.p.A. all
licensed to Datalogic Scanning, Inc. All other trademarks and trade names referred to herein are property of their
respective owners.
This product may be covered by one or more of the following patents: 4603262 • 4639606 • 4652750 • 4672215 • 4699447 • 4709369 • 4749879 • 4786798 • 4792666 • 4794240 •
4798943 • 4799164 • 4820911 • 4845349 • 4861972 • 4861973 • 4866257 • 4868836 • 4879456 • 4939355 • 4939356 • 4943127 • 4963719 • 4971176 • 4971177 • 4991692 •
5001406 • 5015831 • 5019697 • 5019698 • 5086879 • 5115120 • 5144118 • 5146463 • 5179270 • 5198649 • 5200597 • 5202784 • 5208449 • 5210397 • 5212371 • 5212372 •
5214270 • 5229590 • 5231293 • 5232185 • 5233169 • 5235168 • 5237161 • 5237162 • 5239165 • 5247161 • 5256864 • 5258604 • 5258699 • 5260554 • 5274219 • 5296689 •
5298728 • 5311000 • 5327451 • 5329103 • 5330370 • 5347113 • 5347121 • 5371361 • 5382783 • 5386105 • 5389917 • 5410108 • 5420410 • 5422472 • 5426507 • 5438187 •
5440110 • 5440111 • 5446271 • 5446749 • 5448050 • 5463211 • 5475206 • 5475207 • 5479011 • 5481098 • 5491328 • 5493108 • 5504350 • 5508505 • 5512740 • 5541397 •
5552593 • 5557095 • 5563402 • 5565668 • 5576531 • 5581707 • 5594231 • 5594441 • 5598070 • 5602376 • 5608201 • 5608399 • 5612529 • 5629510 • 5635699 • 5641958 •
5646391 • 5661435 • 5664231 • 5666045 • 5671374 • 5675138 • 5682028 • 5686716 • 5696370 • 5703347 • 5705802 • 5714750 • 5717194 • 5723852 • 5750976 • 5767502 •
5770847 • 5786581 • 5786585 • 5787103 • 5789732 • 5796222 • 5804809 • 5814803 • 5814804 • 5821721 • 5822343 • 5825009 • 5834708 • 5834750 • 5837983 • 5837988 •
5852286 • 5864129 • 5869827 • 5874722 • 5883370 • 5905249 • 5907147 • 5923023 • 5925868 • 5929421 • 5945670 • 5959284 • 5962838 • 5979769 • 6000619 • 6006991 •
6012639 • 6016135 • 6024284 • 6041374 • 6042012 • 6045044 • 6047889 • 6047894 • 6056198 • 6065676 • 6069696 • 6073849 • 6073851 • 6094288 • 6112993 • 6129279 •
6129282 • 6134039 • 6142376 • 6152368 • 6152372 • 6155488 • 6166375 • 6169614 • 6173894 • 6176429 • 6188500 • 6189784 • 6213397 • 6223986 • 6230975 • 6230976 •
6237852 • 6244510 • 6259545 • 6260763 • 6266175 • 6273336 • 6276605 • 6279829 • 6290134 • 6290135 • 6293467 • 6303927 • 6311895 • 6318634 • 6328216 • 6332576 •
6332577 • 6343741 • 6454168 • 6478224 • 6568598 • 6578765 • 6705527 • 6974084 • 6991169 • 7051940 • 7170414 • 7172123 • 7201322 • 7204422 • 7215493 • 7224540 •
7234641 • 7243850• 601 26 118.6 • AU703547 • D312631 • D313590 • D320011 • D320012 • D323492 • D330707 • D330708 • D349109 • D350127 • D350735 • D351149 • D351150
• D352936 • D352937 • D352938 • D352939 • D358588 • D361565 • D372234 • D374630 • D374869 • D375493 • D376357 • D377345 • D377346 • D377347 • D377348 • D388075 •
D446524 • EP0256296 • EP0260155 • EP0260156 • EP0295936 • EP0325469 • EP0349770 • EP0368254 • EP0442215 • EP0498366 • EP0531645 • EP0663643 • EP0698251 •
EP01330772 • GB2252333 • GB2284086 • GB2301691 • GB2304954 • GB2307093 • GB2308267 • GB2308678 • GB2319103 • GB2333163 • GB2343079 • GB2344486 •
GB2345568 • GB2354340 • ISR107546 • ISR118507 • ISR118508 • JP1962823 • JP1971216 • JP2513442 • JP2732459 • JP2829331 • JP2953593 • JP2964278 • MEX185552 •
MEX187245 • RE37166 • Other Patents Pending
Table of Contents
About This Manual ............................................................................................................... 1-1
Manual Conventions ....................................................................................................... 1-1
Connecting the Scanner ....................................................................................................... 1-2
Programming ..................................................................................................................... 1-3
Using the Programming Bar Codes ................................................................................... 1-3
Resetting the Standard Product Defaults ................................................................................ 1-3
LED and Beeper Indicators ................................................................................................... 1-4
Error Codes ........................................................................................................................ 1-5
Double Read Timeout .......................................................................................................... 2-1
PDF Double Read Timeout .................................................................................................... 2-2
Label Gone Timeout ............................................................................................................ 2-4
PDF Label Gone Timeout ...................................................................................................... 2-4
Sleep Mode ........................................................................................................................ 2-5
LED and Beeper Indicators ................................................................................................... 2-7
Power On Alert .............................................................................................................. 2-7
Good Read: When to Indicate .......................................................................................... 2-8
Good Read Beep Control ................................................................................................. 2-9
Good Read Beep Frequency ............................................................................................ 2-9
Good Read Beep Length ................................................................................................2-10
Good Read Beep Volume ...............................................................................................2-11
Productivity Index Reporting (PIR) .......................................................................................2-11
Scanning Features .............................................................................................................2-12
Aiming Pointer .............................................................................................................2-12
Targeted Scanning Mode ...............................................................................................2-12
Wake Up Intensity ........................................................................................................2-15
Interface Selection .............................................................................................................. 3-3
Interface Features ............................................................................................................... 3-7
RS-232 Interface Features .............................................................................................. 3-9
ACK NAK Error Handling ................................................................................................3-23
IBM-USB Interface Features ...........................................................................................3-24
IBM ............................................................................................................................3-25
Wand Emulation ...........................................................................................................3-26
Keyboard Wedge ..........................................................................................................3-30
USB Keyboard ..............................................................................................................3-30
Data Editing Overview ......................................................................................................... 4-1
Please Keep In Mind... .................................................................................................... 4-1
Global Prefix/Suffix ............................................................................................................. 4-2
AIM ID .............................................................................................................................. 4-4
Label ID ............................................................................................................................ 4-5
Case Conversion ................................................................................................................4-11
Character Conversion .........................................................................................................4-12
UPC-A ............................................................................................................................... 5-1
Disable/Enable UPC-A .................................................................................................... 5-1
Check Digit Transmission ................................................................................................ 5-2
Expand UPC-A to EAN-13 ................................................................................................ 5-2
Number System Transmission ......................................................................................... 5-3
UPC-A Minimum Reads ................................................................................................... 5-3
UPC-A In-store Minimum Reads ....................................................................................... 5-4
UPC-E ............................................................................................................................... 5-5
Disable/Enable UPC-E .................................................................................................... 5-5
Check Digit Transmission ................................................................................................ 5-5
Number System Digit ..................................................................................................... 5-6
Expand UPC-E to UPC-A ................................................................................................. 5-6
Expand UPC-E to EAN13 ................................................................................................. 5-7
Product Reference Guide
i
Minimum Reads ............................................................................................................. 5-7
GTIN ............................................................................................................................5-8
Expand UPC/EAN to GTIN ................................................................................................ 5-8
EAN-13 ..............................................................................................................................5-9
Disable/Enable EAN-13 ................................................................................................... 5-9
Check Digit Transmission ................................................................................................ 5-9
EAN-13 Flag 1 Character ............................................................................................... 5-10
ISBN .......................................................................................................................... 5-10
Minimum Reads ........................................................................................................... 5-11
EAN-8 .............................................................................................................................. 5-12
Disable/Enable EAN-8 ................................................................................................... 5-12
Check Digit Transmission .............................................................................................. 5-12
Minimum Reads ........................................................................................................... 5-13
Enable EAN Two-Label ........................................................................................................ 5-14
Enable EAN Two-Label Combined ......................................................................................... 5-14
Add-ons ........................................................................................................................... 5-15
RSS-14 ............................................................................................................................ 5-17
Disable/Enable RSS-14 ................................................................................................. 5-17
RSS-14 UCC/EAN 128 Emulation .................................................................................... 5-17
Minimum Reads ........................................................................................................... 5-18
RSS-14 2D Component ................................................................................................. 5-19
RSS Expanded .................................................................................................................. 5-20
Disable/Enable RSS Expanded ....................................................................................... 5-20
RSS Expanded UCC/EAN 128 Emulation .......................................................................... 5-20
Length Control ............................................................................................................. 5-21
RSS Expanded Length 1, Length 2 Programming Instructions ............................................. 5-22
Minimum Reads ........................................................................................................... 5-23
RSS Expanded 2D Component ....................................................................................... 5-24
RSS Limited ...................................................................................................................... 5-24
Disable/Enable RSS Limited ........................................................................................... 5-24
RSS Limited UCC/EAN 128 Emulation .............................................................................. 5-25
Minimum Reads ........................................................................................................... 5-25
RSS Limited 2D Component ........................................................................................... 5-26
Code 39 ........................................................................................................................... 5-27
Disable/Enable Code 39 ................................................................................................ 5-27
Check Character Calculation .......................................................................................... 5-27
Check Character Transmit ............................................................................................. 5-28
Start/Stop Characters ................................................................................................... 5-28
Code 39 Full ASCII ....................................................................................................... 5-29
Length Control ............................................................................................................. 5-30
Code 39 Length 1, Length 2 Programming Instructions ..................................................... 5-31
Quiet Zones ................................................................................................................ 5-31
Code 39 Stitching ........................................................................................................ 5-32
Minimum Reads ........................................................................................................... 5-32
Pharmacode 39 ................................................................................................................. 5-33
Disable/Enable Pharmacode 39 ...................................................................................... 5-33
Start/Stop Characters ................................................................................................... 5-33
Check Character Transmit ............................................................................................. 5-34
Code 128 and UCC/EAN 128 ............................................................................................... 5-35
Transmit Function Characters ........................................................................................ 5-36
Length Control ............................................................................................................. 5-37
Code 128 Length 1, Length 2 Programming Instructions .................................................... 5-38
Code 128 Conversion to Code 39 ................................................................................... 5-38
Code 128 Stitching ....................................................................................................... 5-39
Minimum Reads ........................................................................................................... 5-39
Interleaved 2 of 5 .............................................................................................................. 5-40
Disable/Enable Interleaved 2 of 5 ................................................................................... 5-40
Check Digit Calculation ................................................................................................. 5-40
Check Digit Transmit .................................................................................................... 5-41
Length Control ............................................................................................................. 5-42
ii Magellan® 1400i
Interleaved 2 of 5 Length 1, Length 2 Programming Instructions .........................................5-43
Interleaved 2 of 5 Stitching ............................................................................................5-44
Minimum Reads ............................................................................................................5-45
Codabar ............................................................................................................................5-46
Disable/Enable Codabar .................................................................................................5-46
Check Character Verification ..........................................................................................5-46
Check Character Transmit ..............................................................................................5-47
Length Control .............................................................................................................5-48
Codabar Length 1, Length 2 Programming Instructions ......................................................5-49
Start/Stop Character Type .............................................................................................5-50
Start/Stop Character Transmission ..................................................................................5-50
Start/Stop Character Match ...........................................................................................5-51
Codabar Stitching .........................................................................................................5-51
Minimum Reads ............................................................................................................5-52
Code 93 ............................................................................................................................5-53
Disable/Enable Code 93 .................................................................................................5-53
Length Control .............................................................................................................5-54
Code 93 Length 1, Length 2 Programming Instructions ......................................................5-55
Code 93 Stitching .........................................................................................................5-56
Minimum Reads ............................................................................................................5-56
MSI/Plessey ......................................................................................................................5-57
Disable/Enable MSI/Plessey ...........................................................................................5-57
Check Digit Verification .................................................................................................5-57
Check Digit Transmit .....................................................................................................5-58
Number of Check Characters ..........................................................................................5-58
Length Control .............................................................................................................5-59
MSI/Plessey Length 1, Length 2 Programming Instructions .................................................5-60
MSI/Plessey Stitching ....................................................................................................5-61
Minimum Reads ............................................................................................................5-62
Standard 2 of 5 .................................................................................................................5-63
Disable/Enable Standard 2 of 5 ......................................................................................5-63
Check Digit Verification .................................................................................................5-63
Check Digit Transmit .....................................................................................................5-64
Length Control .............................................................................................................5-65
Standard 2 of 5 Length 1, Length 2 Programming Instructions ............................................5-66
Standard 2 of 5 Stitching ...............................................................................................5-67
Minimum Reads ............................................................................................................5-68
PDF417 ............................................................................................................................5-69
Disable/Enable PDF417 .................................................................................................5-69
PDF417 Minimum Reads ................................................................................................5-69
Length Control .............................................................................................................5-70
PDF417 Length 1, Length 2 Programming Instructions .......................................................5-71
Micro PDF417 ....................................................................................................................5-72
Disable/Enable Micro PDF417 .........................................................................................5-72
Micro PDF 128 Emulation ...............................................................................................5-73
Micro PDF417 Minimum Reads ........................................................................................5-74
Length Control .............................................................................................................5-75
Micro PDF417 Length 1, Length 2 Programming Instructions ..............................................5-76
Optical and Read Performance Parameters ............................................................................. A-1
Scanner Dimensions ............................................................................................................ A-1
Physical Properties .............................................................................................................. A-2
Electrical Parameters ........................................................................................................... A-2
Environmental Parameters ................................................................................................... A-2
Other Parameters ...............................................................................................................A-2
Standard Cable Pinouts (Primary Interface Cables) .................................................................. B-1
RS-232 ........................................................................................................................ B-1
IBM Port 5B/9B/17 ........................................................................................................ B-1
IBM USB ...................................................................................................................... B-2
USB & USB Keyboard ..................................................................................................... B-2
Wand Emulation ............................................................................................................ B-2
Product Reference Guide
iii
Keyboard Wedge ............................................................................................................B-2
Standard Feature Defaults ................................................................................................... D-1
Keyboard Model Cross Reference ........................................................................................... E-1
Accepting RS-232 Commands ............................................................................................... F-1
iv Magellan® 1400i
The Magellan®1400i Omni-Directional Imaging Scanner offers hands-free scanning for small,
easily handled items and handheld scanning for bulkier items. Its aggressive imaging performance and intuitive operation reduces user training and speeds checkout for better customer
service.
About This Manual
This manual presents advanced user information which includes connection, programming,
product and cable specifications, and other useful references. For additional information, such
as installation, maintenance, troubleshooting and warranty information, see the Quick Reference Guide (QRG). Copies of other publications for this product are downloadable free of
charge from the website listed on the back cover of this manual.
On leaving the factory, units are programmed for the most common terminal and communications settings. If you need to change these settings, custom programming can be accomplished
by scanning the bar codes in this guide.
Chapter 1
Getting Started
Bold text and a yellow-highlighted background indicates the most common default setting for a
feature/option.
Manual Conventions
The symbols listed below are used in this manual to notify the reader of key issues or procedures
that must be observed when using the scanner:
NOTE
CAUTION
Notes contain information necessary for properly diagnosing, repairing and operating the
scanner.
The CAUTION symbol advises you of actions
that could damage equipment or property.
Product Reference Guide
1-1
Getting Started
Connecting the Scanner
The scanner kit you ordered to match your interface should provide a compatible cable for your
installation. Use the appropriate instructions below to connect the scanner to the terminal, PC
or other host device.
Upon completing the connection via the appropriate interface instructions below, proceed to
Interface Related Features section of this manual and scan the bar code to select the correct
the
interface type.
RS-232 Serial Connection —
to the terminal/PC serial port via the RS-232 cable as shown in
Turn off power to the terminal/PC and connect the scanner
Figure 1. If the terminal will not
support POT (Power Off the Terminal) to supply scanner power, use the approved power supply
(AC Adapter). Plug the AC Adapter barrel connector into the socket on the RS-232 cable connector and the AC Adapter plug into a standard power outlet.
Figure 1
USB Connection —
USB cable for the interface type you ordered. Reference
. RS-232 Serial or USB Connection using A/C Adapter
I/F Cable
Connect
Here
To Host/Terminal
A/C Adapter
(if needed)
Connect the scanner to a USB port on the terminal/PC using the correct
Figure 1 and Figure 2.
USB installations may require a power connection via
NOTE
an approved A/C Adapter as shown in
example, this would be the case if the scanner is connected along with a number of other devices to a nonpowered USB hub.
Figure 1. For
For 220-230 VAC
adapters, the
cord must be
facing down as
shown in the
illustration. If
installed upwards,
it will pose an
undue strain on the
socket outlet.
Figure 2. Other Connection Types
B
S
K
U
e
y
W
b
o
e
a
d
r
(Decoder required
for Wand Emulation)
or...
d
n
a
W
M
B
I
or...
d
g
e
1-2 Magellan® 1400i
Programming
Wand Emulation Connection —
nal/PC via a decoder
Figure 2.
IBM Connection —
rect IBM cable. Reference
Keyboard Wedge Connection —
1
using the correct cable for the interface type you ordered. Reference
Connect the scanner to the IBM port on the terminal/PC using the cor-
Figure 2.
Connect the scanner to the appropriate port on the termi-
Before connection, turn off power to the terminal/PC.
The Keyboard Wedge cable has a ‘Y’ connection from the scanner. Connect the female to the
male end from the keyboard and the remaining end at the keyboard port at the terminal/PC.
Reference
Figure 2.
Programming
The scanner is typically factory-configured with a set of default features standard to the interface
type you ordered. After scanning the interface bar code from the
tion, you can select other options and customize your scanner through use of the instructions
and programming bar codes available in that section and also the
chapters of this manual.
Using the Programming Bar Codes
This manual contains feature descriptions and bar codes which allow you to reconfigure your
scanner. Some programming bar code labels, like the label below for resetting defaults, require
only the scan of that single label to enact the change. Most of the programming labels in this
manual, however, require the scanner to be placed in Programming Mode prior to scanning
them. Scan a START/END bar code once to enterProgramming Mode. Once the scanner is in
Programming Mode, you can scan a number of parameter settings before scanning the START/
END bar code a second time, which will then accept your changes, exit Programming Mode
and return the scanner to normal operation.
Interface Related Features sec-
Data Editing and Symbologies
Resetting the Standard Product Defaults
If you are unsure of what programming options are in your scanner, or you’ve changed some
options and want the factory settings restored, scan the Standard Product Default Settings bar
code below (you do not have to scan START/END bar codes when scanning the Standard Product Default Settings bar code). This will copy the factory configuration for the currently active
interface to the current configuration.
Standard Product Default Settings
The programming section lists the factory default settings for each of the menu commands for
the standard RS-232 interface in
tings for the other interfaces can be found in
1. Wand Emulation requires a decoder.
Product Reference Guide
BOLD text on the following pages. Exceptions to default set-
Appendix D, Default Settings.
1-3
Getting Started
LED and Beeper Indicators
The scanner’s beeper sounds and its green LED illuminates to indicate various functions
or errors on the scanner. The tables below list these indications. One exception to the
behaviors listed in the tables is that the scanner’s functions are programmable, and may
or may not be turned on. For example, certain indications, such as the power-up beep
can be disabled using programming bar code labels.
Green LED Indications
LED
INDICATION
Power-on
indication
Good Read
Indication
Scanner Ready Constant dim green The scanner is ready for operation.
Sleep Mode
Host Disable
Diagnostics
BEEPER FUNCTIONS
BEEPER
INDICATION
Bright green flash
Bright green flash Indicates a bar code has been read and decoded.
Constant green flash
(100mS on, 1900mS off)
Constant green flash at 1 Hz
(100mS on, 900mS off)
Varies (see "Error Codes" on
page 1-5 for more information)
INDICATION COMMENT
Indicates the scanner has finished all its power up tests and is
now ready for ooperation.
The scanner is in Sleep Mode. To wake the scanner up, move
an object in front of its window or press the button atop the
unit.
The scanner is disabled due to receiving a disble command
from the POS terminal.
The LED can provide diagnostic feedback if the scanner discovers a problem during SelfTest.
INDICATION COMMENT
The Power-On LED indication is a configurable feature which
Power On Beep Single beep
Good Read
Indication
Diagnostics
Programming
Mode
Indications
1-4 Magellan® 1400i
Single beep
Varies (see "Error Codes" on
page 1-5 for more information)
Varies (see the Product Reference
Guide for more information about
scanner programming)
can be enabled or disabled. When enabled, this beep Indicates the scanner has finished all its power up tests and is
now ready for operation.
The good read beep indication is configurable. Options
include: Enable/disable, frequency, duration and volume. See
the Product Reference Guide (PRG) for more information.
The Beeper can provide diagnostic feedback if the scanner
discovers a problem during SelfTest.
The Beeper will sound as programming bar code labels are
scanned, indicating progress during scanner configuration.
Error Codes
Upon startup, if the scanner flashes its indicator LED or sounds an unexpected series of beep
tones (other than normal power-up indications), this means the scanner has not passed its automatic Selftest and has entered FRU
pressed, the sequence will be repeated. The following table describes the LED flashes/beep codes
associated with an error found.
NUMBER OF
LED FLASHES/
ERROR CORRECTIVE ACTION
BEEPS
1 Configuration
2 Interface PCB
6 Main PCB
10 Button Error
Error Codes
1
isolation mode. If the scanner is reset or the button is
11
12
13
14
Near Field
Imager Module
Far Field
Imager Module
Software ID
Failure
CPLD/Code
Mismatch
Contact Helpdesk for assistance
1. Field Replaceable Unit (FRU)
Product Reference Guide
1-5
Getting Started
NOTES
1-6 Magellan® 1400i
Double Read Timeout
The Double Read Timeout feature sets a time limit that determines how much time must pass
before reading the same label again (e.g. two identical items in succession).
0.1 Second
Chapter 2
General Features
START / END
PROGRAMMING BAR CODES
0.3 Second
0.5 Second
0.2 Second
0.4 Second
0.6 Second
DEFAULT
Product Reference Guide
2-1
General Features
Double Read Timeout — cont.
PROGRAMMING BAR CODES
0.7 Second
0.9 Second
START / END
0.8 Second
PDF Double Read Timeout
This double read timer value is used ONLY when
scanning PDF417 bar codes.
NOTE
The PDF Double Read Timeout feature sets a time limit that determines how much time must
pass before reading the same PDF417 label again (e.g. two identical PDF417 bar codes in succession).
PROGRAMMING BAR CODES
1 Second
START / END
1.5 Seconds
2-2 Magellan® 1400i
Read Timeout
PDF Double Read Timeout — cont.
PROGRAMMING BAR CODES
1.8 Seconds
DEFAULT
PDF Double
START / END
1.6 Seconds
1.9 Seconds
2 Seconds
2.2 Seconds
2.4 Seconds
2.1 Seconds
2.3 Seconds
2.55 Seconds
Product Reference Guide
2-3
General Features
Label Gone Timeout
This feature sets the time after the last label segment is seen before the scanner prepares for a
new label.
START / END
PROGRAMMING BAR CODES
Sets the label gone timeout duration using hex values from 000 to 255 in increments of ten milliseconds (10ms or 0.01 seconds). To
configure this feature, scan the “START/END” bar code above to place the unit in Programming Mode, then the “Set Label Gone Timeout,” followed by three digits (zero padded) from the Alphanumeric table in
desired time value. Exit programming mode by scanning the “START/END” bar code again.
DEFAULT SETTING FOR THIS FEATURE: 200 milliseconds (020)
Appendix C, Alpha-Numeric Pad representing the
Set Label Gone Timeout
PDF Label Gone Timeout
This setting specifies how long the Label Gone Timeout timer runs when specifically collecting
PDF label segments prior to discarding data.
START / END
PROGRAMMING BAR CODES
Sets the label gone timeout duration using hex values from 001 to 255 in increments of ten milliseconds (10ms or 0.01 seconds). To
configure this feature, scan the “START/END” bar code above to place the unit in Programming Mode, then the “Set PDF Label Gone
Timeout,” followed by three digits (zero padded) from the Alphanumeric table in
desired time value. Exit programming mode by scanning the “START/END” bar code again.
DEFAULT SETTING FOR THIS FEATURE: 1.5 Seconds (150)
Appendix C, Alpha-Numeric Pad representing the
Set PDF Label Gone Timeout
2-4 Magellan® 1400i
Sleep Mode
This feature specifies the amount of time with no bar code reads before the scanner enters sleep mode.
Sleep Mode
START / END
PROGRAMMING BAR CODES
15 Seconds
DEFAULT
30 Seconds
1 Minute
3 Minutes
5 Minutes
2 Minutes
4 Minutes
Product Reference Guide
2-5
General Features
Sleep Mode — cont.
START / END
7 Minutes
PROGRAMMING BAR CODES
6 Minutes
8 Minutes
9 Minutes
12 Minutes
30 Minutes
10 Minutes
DEFAULT
15 Minutes
1 Hour
2-6 Magellan® 1400i
Beeper Indicators
LED and Beeper Indicators
Power On Alert
Disables or enables the indication (a single beep) that the scanner has finished all its power up
tests and is now ready for operation.
PROGRAMMING BAR CODES
Disable
LED and
START / END
Enable
DEFAULT
Product Reference Guide
2-7
General Features
Good Read: When to Indicate
This feature specifies when the scanner will provide indication (beep and/or flash its green LED)
upon successfully reading a bar code. Choices are:
• Good Read = Indicate after decode
• Good Read = Indicate after transmit
• Good Read = Indicate after CTS goes inactive, then active
This option (Indicate after CTS goes inactive, then
active), which uses CTS, is only valid for RS-232 interfaces.
NOTE
PROGRAMMING BAR CODES
START / END
After Decode
DEFAULT
After CTS goes inactive, then active
After Transmit
2-8 Magellan® 1400i
Beeper Indicators
Good Read Beep Control
This feature enables/disables the scanner’s ability to beep upon a successful decode of a bar code.
Disable
LED and
START / END
PROGRAMMING BAR CODES
Enable
DEFAULT
Good Read Beep Frequency
Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable
from the list below. (Controls the beeper’s pitch/tone.)
PROGRAMMING BAR CODES
Low
High
START / END
Medium
DEFAULT
Product Reference Guide
2-9
General Features
Good Read Beep Length
Specifies the duration of a good read beep.
60msec
DEFAULT
100msec
START / END
PROGRAMMING BAR CODES
80msec
140msec
180msec
120msec
160msec
200msec
2-10 Magellan® 1400i
ty Index Reporting (PIR)
Good Read Beep Volume
Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume
levels.
Low
High
DEFAULT
Productivi-
START / END
PROGRAMMING BAR CODES
Medium
Productivity Index Reporting (PIR)
When PIR is enabled, label quality data is appended to decoded data before being presented to
the POS. The PIR feature allows the scanner to provide information to an external computer,
indicating how easy the label was to read.
This value-added feature is a factory-programmed
option. Contact your dealer for information about
upgrading your system to include this advanced
NOTE
Disable
DEFAULT
capability.
PROGRAMMING BARCODES
START / END
Enable
Product Reference Guide
2-11
General Features
Scanning Features
Aiming Pointer
This feature enables/disables the Aiming Pointer for all symbologies.
START / END
PROGRAMMING BAR CODES
Enable always on
Targeted Scanning Mode
Disable
DEFAULT
Upon pressing the button, the scanner will project an aiming pattern to assist in centering over
the bar code. Scanning then takes place as soon as the button is released.
When add-ons are enabled and a bar code is being read while in Targeted
Mode, position the pointer at or near the end of the base label to ensure
the scanner will read both the base and add-on label.
NOTE
Targeted Scanning Mode will read bar codes in any orientation.
The scanner will return to full pattern Omni-directional Mode after either
of the following has ocurred:
- Good Read +
-
Target Mode: Active Time + Target Mode: Linger Time has elapsed.
Target Mode: Linger Time has elapsed.
Configuration options for Targeted Scanning Mode are:
• Target Mode: Active Time
• Target Mode: Linger Time
2-12 Magellan® 1400i
Features
Scanning
Target Mode: Active Time
Specifies the time duration the scanner attempts to decode labels while in the targeted mode of
operation.
START / END
PROGRAMMING BAR CODES
Extra Short Duration
Short Duration
Medium Duration
DEFAULT
Long Duration
Product Reference Guide
2-13
General Features
Target Mode: Linger Time
Specifies the time duration the scanner remains in the targeted mode of operation after reading
a bar code or after
Mode. The linger timer starts upon a good read or upon timeout of
whichever is earliest. A button press at any time will reset the process back to the start.
NOTE
START / END
Target Mode: Active Time has expired, before reverting to Omni-directional
Target Mode: Active Time;
Active Time and Linger Time settings are totally independent from one another.
During the period Linger Time is active, no bar codes can
be read, no matter what mode the scanner is in.
PROGRAMMING BAR CODES
Short Duration
Medium Duration
DEFAULT
Long Duration
2-14 Magellan® 1400i
Features
Wake Up Intensity
This feature indicates the percentage of ambient light change which will trigger the scanner to
wake up from Sleep Mode. Lower settings provide greater sensitivity.
5%
10%
DEFAULT
Scanning
START / END
PROGRAMMING BAR CODES
8%
20%
30%
15%
25%
35%
Product Reference Guide
2-15
General Features
Wake Up Intensity — cont.
PROGRAMMING BAR CODES
40%
60%
START / END
50%
70%
80%
2-16 Magellan® 1400i
Chapter 3
Interface Related Features
At the time of this writing, the Scanner supports the interfaces listed in Ta b le 3 - 1. Select the
desired interface type from the table, then reference the page number given for the customizable
features section associated with each interface. See
Wedge interface type (A through Y as listed).
Table 3-1. Interfaces Supported
RS-232 Page Keyboard Wedge Page
RS-232 Standard
RS-232 Wincor-Nixdorf
IBM
IBM 4683 Port 5B
IBM 4683 Port 9B
IBM 4683 Port 17
USB
IBM USB
USB Keyboard
Wand Emulation
Wand Emulation 3-26
Keyboard Wedge 3-30
Keyboard Wedge A
Keyboard Wedge B
Keyboard Wedge C
Keyboard Wedge D
Keyboard Wedge E
Keyboard Wedge F
Keyboard Wedge G
a. Consult Ta bl e for more information regarding keyboard interface types.
a
a
a
a
a
a
a
3-9
3-9
3-24
3-24
3-24
3-24
3-24
3-30
3-30
3-30
3-30
3-30
3-30
3-30
Ta bl e 3 -2 for a description of each Keyboard
Keyboard Wedge H
Keyboard Wedge I
Keyboard Wedge J
Keyboard Wedge K
Keyboard Wedge L
Keyboard Wedge M
Keyboard Wedge N
Keyboard Wedge N
Keyboard Wedge O
Keyboard Wedge P
Keyboard Wedge Q
Keyboard Wedge R
Keyboard Wedge S
Keyboard Wedge T
Keyboard Wedge U
Keyboard Wedge V
Keyboard Wedge W
Keyboard Wedge X
Keyboard Wedge Y
a
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
a
3-30
NOTE
Product Reference Guide
The correct interface cable is included for the scanner
interface type you ordered.
3-1
Interface Related Features
Table 3-2. Keyboard Wedge Interface Reference
I/F Type PCs Supported
A PC/XT w/Alternate Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key
B
Encoding
C PS/2 25 and 30 w/Alternate Key Encoding
D PC/XT w/Standard Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key
E
Encoding
F PS/2 25 and 30 w/Standard Key Encoding
G IBM 3xxx w/122 keyboard
H IBM 3xxx w/102 keyboard
I PS/55 5530T w/104 keyboard
J NEC 9801
K WYSE 30/30+ WY-30 Keyboard 83 Keys
WYSE 60/85/99 GT/150/160/285 Style IBM Enhanced PC, 520/520ES
L
Style IBM Enhanced PC FR
WYSE 55/65/65 ES/120/185/325 Style IBM Enhanced PC
WYSE 60/85/99 GT/150/160/285 ANSI Keyboard 105 Keys, 520/520 ES
M
ANSI Keyboard 105 Keys
WYSE 55/65/65 ES/120/185/325 ANSI Keyboard 105 Keys
WYSE 60/85/99 GT/150/160/285 ASCII Kbd, 520/520 ES ASCII Kbd
N
WYSE 55/65/65 ES/120/185/325 ASCII Keyboard
WYSE 60/85/99 GT/150/160/285 ANSI W285 Keyboard 105 Keys, 520/
O
520 ES ANSI W285 Keyboard 105 Keys
WYSE 55/65/65 ES/120/185/325 ANSI W285 Keyboard 105 Keys
P WYSE WINTERM 3320 SE
IBM 3153
Q
IBM 316X, 3179/3180/319X/3270
R IBM 3151/3152-010, 347X/348X
S DIGITAL VT 220/320/330/340/350/382
T DIGITAL VT420
U DIGITAL VT 510/520 IBM ANSI Style Keyboard
V DIGITAL VT 510/520 IBM PC Style Keyboard
W SUN SPARC 5/10
X SUN 420/440, ITX
Y WYSE 370/355 Style Enhanced IBM PC
Reference
pings for more information about keyboards.
Appendix E, Keyboard Function Key Map-
NOTE
3-2 Magellan® 1400i
Loading...