Datalogic 0009 User Manual

Datalogic Jet™

USER'S MANUAL

DATALOGIC S.p.A.
Via Candini 2
40012 - Lippo di Calderara di Reno
Bologna - Italy

Datalogic Jet™ - User's Manual

Ed.: 06/2005

ALL RIGHTS RESERVED
Datalogic reserves the right to make modifications and improvements without prior notification.

Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or
consequential damages resulting from the use of this material.

Product names mentioned herein are for identification purposes only and may be trademarks and or
registered trademarks of their respective companies.

© Datalogic S.p.A. 2004-2005

CONTENTS

DATALOGIC END USER LICENSE AGREEMENT..................................... v

REFERENCES ........................................................................................... vii

Conventions.................................................................................................vii

Reference Documentation ...........................................................................vii

Services and Support...................................................................................vii

SAFETY REGULATIONS.......................................................................... viii

General Safety Rules.................................................................................. viii

Laser Safety..................................................................................................ix

Radio Compliance....................................................................................... xiii

Information for the User ..............................................................................xiii

FCC ............................................................................................................xiv

GENERAL VIEW ........................................................................................ xv

1 INTRODUCTION .......................................................................................... 1

1.1 Datalogic Jet™ PDA Description .................................................................. 1

1.2 Available Models........................................................................................... 1

1.3 Package Contents......................................................................................... 2

1.4 Accessories................................................................................................... 3

2 CONNECTIONS ........................................................................................... 4

2.1 PDA Connection to the Host Computer ........................................................ 4

2.1.1 RS232/USB Direct Connection ..................................................................... 4

2.1.2 WLAN Connection ........................................................................................ 5

2.1.3 WPAN Connections ......................................................................................6

2.1.4 WWAN Connections .....................................................................................7

2.2 Connection Cables...................................................................................... 10

3 USE AND FUNCTIONING.......................................................................... 11

3.1 PDA Startup................................................................................................ 11

3.2 Using the Stylus.......................................................................................... 12

3.3 Data Capture............................................................................................... 13

3.3.1 Laser Data Capture..................................................................................... 13

3.3.2 Imager Data Capture .................................................................................. 14

3.3.3 RFID Data Capture ..................................................................................... 15

3.4 Description of the Keys ............................................................................... 16

3.4.1 System Control and Navigation Keys.......................................................... 16

3.4.2 Key Selection.............................................................................................. 18

3.5 Status Indicators ......................................................................................... 22

3.5.1 LED Status.................................................................................................. 22

iii

3.5.2 Status Bar ................................................................................................... 23

3.6 Data Capture Configuration ........................................................................ 24

3.6.1 Configure .................................................................................................... 24

3.6.2 Capture ....................................................................................................... 28

3.7 Control Panel .............................................................................................. 29

3.7.1 Buttons........................................................................................................ 30

3.7.2 Registry....................................................................................................... 30

3.7.3 Files Admin ................................................................................................. 31

3.7.4 Wireless Communications........................................................................... 33

3.7.5 Bluetooth® Manager Device Setup............................................................. 36

3.8 Windows Connections ................................................................................ 34

3.8.1 Microsoft® ActiveSync® ............................................................................. 34

3.9 Backup Directory File Management ............................................................ 39

4 MAINTENANCE ......................................................................................... 40

4.1 Charging the Battery pack .......................................................................... 40

4.2 Replacing the Battery pack ......................................................................... 41

4.3 Cleaning the PDA ....................................................................................... 42

5 TECHNICAL FEATURES........................................................................... 43

5.1 Technical Data ............................................................................................ 43

5.2 Reading Diagrams ......................................................................................46

6 TEST CODES............................................................................................. 47

GLOSSARY................................................................................................ 50

iv

INDEX......................................................................................................... 53

DATALOGIC END USER LICENSE AGREEMENT

BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR BY USING DATALOGIC EQUIPMENT THAT
INCLUDES THIS SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU
DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, THEN DO NOT DOWNLOAD, INSTALL,
USE THE SOFTWARE NOR DATALOGIC EQUIPMENT.

The following terms and conditions govern your use of the Software except to the extent that a particular program (a) is the
subject of a separate written agreement with Datalogic or (b) includes a separate “click-on” license agreement as part of the
installation and/or download process. Should a conflict arise between the provisions of the foregoing documents, the order of
precedence shall be (1) the written agreement, (2) the click-on agreement, and (3) this agreement (“Agreement”).

1. License. Subject to the terms and conditions of and except as otherwise provided in this Agreement, Datalogic S.p.A.
(“Datalogic”) and its suppliers grant to Customer (“Customer”) a nonexclusive and nontransferable license to use the specific
program modules, feature set(s) or feature(s) in object code form only as well as associated media, printed materials and
“online” or electronic documentation (the “Software”) for which Customer has paid, if required, the license fees. The Software is
licensed not sold. The license shall be subject to each of the following limitations:

• Unless otherwise expressly provided in the documentation, Customer shall use the Software solely as embedded in, for
execution on, or (where the applicable documentation permits installation on non-Datalogic equipment) for
communication with Datalogic equipment owned or leased by Customer;

• Customer’s use of the Software shall be limited to use on a single hardware chassis, on a single central processing unit,
as applicable, or use on such greater number of chassis or central processing units as Customer may have paid
Datalogic the required license fee; and

• Customer’s use of the Software shall also be limited, as applicable and set forth in Customer’s purchase order or in
Datalogic’s product catalog, user documentation, or web site, to a maximum number of (a) seats (i.e. users with access
to the installed Software), (b) concurrent users, sessions, ports, and/or issued and outstanding IP addresses, and/or (c)
central processing unit cycles or instructions per second. Customer’s use of the Software shall also be limited by any
other restrictions set forth in Customer’s purchase order or in Datalogic’s product catalog, user documentation or web site
for the Software.

2. General Limitations. Except as otherwise expressly provided under this Agreement, Customer shall have no right, and

Customer specifically agrees not to (i) transfer, assign or sublicense its license rights to any other person, or use the Software
on unauthorized or secondhand Datalogic equipment, and any such attempted transfer, assignment or sublicense shall be void;
(ii) correct errors to or otherwise modify or adapt the Software or create derivative works based upon the Software, or to permit
third parties to do the same; or (iii) decompile, decrypt, reverse engineer, disassemble or otherwise reduce the Software to
human-readable form to gain access to trade secrets or confidential information in the Software. To the extent required by law,
at Customer's request, Datalogic shall provide Customer with the interface information needed to achieve interoperability
between the Software and another independently created program, upon payment of Datalogic's applicable fee. Customer shall
observe strict obligations of confidentiality with respect to such information.

3. Upgrades and Additional Copies. For purposes of this Agreement, “Software” shall include (and the terms and conditions of

this Agreement shall apply to) any upgrades, updates, bug fixes or modified versions (collectively, “Upgrades”) or backup copies
of the Software licensed or provided to Customer by Datalogic or an authorized distributor for which Customer has paid the
applicable license fees. Notwithstanding any other provision of this Agreement: (1) customer has no license or right to use any
such additional copies or upgrades unless customer, at the time of acquiring such copy or upgrade, already holds a valid license
to the original Software and has paid the applicable fee for the upgrade, if required; (2) use of upgrades is limited to Datalogic
equipment for which customer is the original end user, purchaser or lessee or who otherwise holds a valid license to use the
Software which is being upgraded; and (3) use of additional copies is limited to backup purposes only.

4. Proprietary Notices. Customer agrees to maintain and reproduce all copyright and other proprietary notices on all copies, in

any form, of the Software in the same form and manner that such copyright and other proprietary notices are included on the
Software. Except as expressly authorized in this Agreement, Customer shall not make any copies or duplicates or any Software
without the prior written permission of Datalogic. Customer may make such backup copies of the Software as may be necessary
for Customer’s lawful use, provided Customer affixes to such copies all copyright, confidentiality, and proprietary notices that
appear on the original.

5. Protection of Information. Customer agrees that aspects of the Software and associated documentation, including the

specific design and structure of individual programs, constitute trade secrets and/or copyrighted material of Datalogic. Customer
shall not disclose, provide, or otherwise make available such trade secrets or copyrighted material in any form to any third party
without the prior written consent of Datalogic. Customer shall implement reasonable security measures to protect such trade
secrets and copyrighted material. Software and documentation shall remain solely property of Datalogic.

v

6. Limited Warranty. If Customer obtained the Software directly from Datalogic, then Datalogic warrants that during the

Warranty Period (as defined below): (i) the media on which the Software is furnished will be free of defects in materials and
workmanship under normal use; and (ii) the Software will substantially conform to its published specifications. The “Warranty
Period” means a period beginning on the date of Customer’s receipt of the Software and ending on the later of (a) ninety (90)
days from the date of initial shipment of the Software by Datalogic, or (b) the end of the minimum period required by the law of
the applicable jurisdiction. The limited warranties extend only to Customer as the original licensee. Customer's sole and
exclusive remedy and the entire liability of Datalogic and its suppliers under these limited warranties will be, at Datalogic’s sole
option, repair or replacement of the Software if reported (or, upon request, returned) to Datalogic. Except as expressly granted
in this Agreement, the Software is provided AS IS and with all faults. Datalogic does not warrant that the Software is error free
or that Customer will be able to operate the Software without problems or interruptions. In addition, due to the continual
development of new techniques for intruding upon and attacking networks, Datalogic does not warrant that the Software or any
equipment, system or network on which the Software is used will be free of vulnerability to intrusion or attack. This warranty
does not apply if the Software (a) is licensed for beta, evaluation, testing or demonstration purposes for which Datalogic does
not receive a license fee, (b) has been altered, except by Datalogic, (c) has not been installed, operated, repaired, or maintained
in accordance with instructions supplied by Datalogic, (d) has been subjected to abnormal physical or electrical stress, misuse,
negligence, or accident, or (e) is used in ultra hazardous activities. If Customer obtained the Software from a Datalogic reseller,
the terms of any warranty shall be as provided by such distributor, and Datalogic provides Customer no warranty with respect to
such Software. The Software may contain support for programs written in Java. Java technology is not fault tolerant and is not
designed, manufactured, or intended for use or resale as online control equipment in hazardous environments requiring fail-safe
performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct
life support machines, or weapons systems, in which the failure of Java technology could lead directly to death, personal injury,
or severe physical or environmental damage. Microsoft Inc. has contractually obligated Datalogic to make this disclaimer.

7. Disclaimer of Warranties. Except as specified in this warranty, all expressed or implied conditions, representations, and

warranties including, without limitation, any implied warranty or condition of merchantability, fitness for a particular purpose, non­infringement, satisfactory quality or arising from a course of dealing, usage, or trade practice, are hereby excluded to the extent
allowed by applicable law. To the extent that an implied warranty cannot be excluded, such warranty is limited in duration to the
warranty period.

8. Disclaimer of Liabilities. In no event will Datalogic or its suppliers be liable for any lost revenue, profit, or data, or for

special, indirect, consequential, incidental, or punitive damages however caused and arising out of the use of or inability to use
the Software even if Datalogic has been advised of the possibility of such damages. In no event shall Datalogic or its suppliers'
liability to customer, whether in contract, tort (including negligence), or otherwise, exceed the price paid by customer. The
foregoing limitations shall apply even if the above-stated warranty fails of its essential purpose.

9. Term and Termination. This Agreement is effective until terminated. Customer may terminate this Agreement at any time by

destroying all copies of Software including any documentation. Customer’s license rights under this Agreement will terminate
immediately without notice from Datalogic if Customer fails to comply with any provision of this Agreement. Upon termination,
Customer must destroy all copies of Software in its possession or control.

10. Customer Records. Customer grants to Datalogic and its independent accountants the right to examine Customer’s books,

records and accounts during Customer’s normal business hours to verify compliance with this Agreement. In the event such
audit discloses non-compliance with this Agreement, Customer shall promptly pay to Datalogic the appropriate license fees.

11. General Provisions. This Agreement shall be governed by and construed in accordance with the laws of Italy. All disputes

arising out of or in connection with this Agreement will be subject to the exclusive jurisdiction of the competent Court of the
place where Datalogic has its registered office. If any portion hereof is found to be void or unenforceable, the remaining
provisions of this Agreement shall remain in full force and effect. Except as expressly provided herein, this Agreement
constitutes the entire agreement between the parties with respect to the license of the Software and supercedes any conflicting
or additional terms contained in the purchase order.

vi

REFERENCES

CONVENTIONS

This manual uses the following conventions:

“User” refers to anyone using a Datalogic Jet™ PDA.
“PDA” and " Datalogic Jet™" refer to Datalogic Jet™ PDA.
“You” refers to the System Administrator or Technical Support person using this
manual to install, configure, operate, maintain or troubleshoot a Datalogic Jet™ PDA.

REFERENCE DOCUMENTATION

For further information regarding Datalogic Jet™ refer to the SDK Help on-Line.

SERVICES AND SUPPORT

Datalogic provides several services as well as technical support through its website.
Log on to www.datalogic.com and click on the links
including:

- PRODUCTS

Search through the links to arrive at your product page where you can download
specific Manuals

and Software & Utilities

indicated for further information

- SERVICES & SUPPORT

- Datalogic Services Warranty Extensions and Maintenance Agreements

- Authorised Repair Centres

- CONTACT US

E-mail form and listing of Datalogic Subsidiaries

vii

SAFETY REGULATIONS

Read this manual carefully before performing any type of connection
to the Datalogic Jet™ PDA.
The user is responsible for any damages caused by incorrect use of

NOTE

GENERAL SAFETY RULES

− Use only the components supplied by the manufacturer for the specific Datalogic
Jet™ PDA being used.

− Do not attempt to disassemble the Datalogic Jet™ PDA, as it does not contain
parts that can be repaired by the user. Any tampering will invalidate the
warranty.

− When replacing the battery pack or at the end of the operative life of the
Datalogic Jet™ PDA, disposal must be performed in compliance with the laws in
force.

− Do not submerge the Datalogic Jet™ PDA in liquid products.

the equipment or by inobservance of the indication supplied in this
manual.

viii

p

LASER SAFETY

The laser light is visible to the human eye and is emitted from the window indicated in
the figure.
This information applies to both Laser models and the Datalogic Jet™ Imager Aiming
System.

Laser out

ut window

I D F E

La luce laser è visibile
all'occhio umano e
viene emessa dalla
finestra indicata nella
figura.

LUCE LASER
NON FISSARE IL FASCIO
APPARECCHIO LASER DI
CLASSE 2
MINIMA POTENZA DI
USCITA:
LUNGHEZZA D'ONDA
EMESSA:
CONFORME A EN 60825-1
(2001)

AVOID EXPOSURE

LASER LIGHT

IS EMITTED FROM

THIS APERTURE

CAUTION-CLASS 2 LASER LIGHT WHEN OPEN - DO NOT STARE INTO BEAM

Die Laserstrahlung ist für
das menschliche Auge
sichtbar und wird am
Strahlaustrittsfenster
ausgesendet (siehe Bild).

LASERSTRAHLUNG
NICHT IN DER STRAHL
BLINKEN
PRODUKT DER
LASERKLASSE 2
MAXIMALE
AUSGANGLEISTUNG:
WELLENLÄNGE:
ENTSPR. EN 60825-1
(2001)

Le rayon laser est visible
à l'oeil nu et il est émis
par la fenêtre désignée
sur l'illustration dans la
figure.

RAYON LASER
EVITER DE REGARDER
LE RAYON
APPAREIL LASER DE
CLASSE 2
PUISSANCE DE SORTIE:
LONGUER D'ONDE EMISE:
CONFORME A EN 60825-1
(2001)

This product complies wit h

21 CFR Subchapter J

LASER LIGHT - DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

MAX. OUTPUT RADIATION 1.4 mW

EMITTED WAVELENGTH 630~680 nm

EN60825-1:2001

La luz láser es visible al
ojo humano y es emitida
por la ventana indicada
en la figura.

RAYO LÁSER
NO MIRAR FIJO EL RAYO
APARATO LÁSER DE
CLASE 2
MÁXIMA POTENCIA DE
SALIDA:
LONGITUD DE ONDA
EMITIDA:
CONFORME A EN 60825-1
(2001)

ix

ENGLISH

The following information is provided to comply with the rules imposed by
international authorities and refers to the correct use of your PDA.

STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR 1040
and EN 60825-1 at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.

Use of controls or adjustments or performance of procedures other
than those specified herein may result in exposure to hazardous

CAUTION

visible laser light.

The product utilizes a low-power laser diode. Although staring directly at the laser
beam momentarily causes no known biological damage, avoid staring at the beam as
one would with any very strong light source, such as the sun. Avoid that the laser
beam hits the eye of an observer, even through reflective surfaces such as mirrors,
etc.

ITALIANO

Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e
si riferiscono all’uso corretto del PDA.

NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data
di produzione: CDRH 21 CFR 1040 e EN 60825-1.
Non si rende mai necessario aprire l’apparecchio per motivi di installazione, utilizzo o
manutenzione.

L'utilizzo di procedure o regolazioni differenti da quelle descritte
nella documentazione può provocare un'esposizione pericolosa

ATTENZIONE

a luce laser visibile.

Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni
riportati dall’occhio umano in seguito ad una esposizione di breve durata, evitare di
fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente di luminosità
intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser negli occhi di un
osservatore, anche attraverso superfici riflettenti come gli specchi.

x

DEUTSCH

Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die von
internationalen Behörden auferlegt wurden, und sie beziehen sich auf den korrekten
Gebrauch vom PDA.

NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH
21 CFR 1040 Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations-, und Wartungs­arbeiten zu öffnen.

Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht
in dieser Betriebsanleitung beschrieben werden, können ein

ACHTUNG

gefährliches Laserlicht verursachen.

Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von
kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den
Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne).
Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines Beobachters, noch
gegen reflektierende Oberflächen zu richten.

FRANÇAIS

Les informations suivantes sont fournies selon les règles fixées par les autorités
internationales et se refèrent à une correcte utilisation du PDA.

NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de
fabrication: CDRH 21 CFR 1040 et EN 60825-1.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.

L'utilisation de procédures ou réglages différents de ceux donnés
ici peut entrainer une dangereuse exposition à lumière laser

ATTENTION

visible.

Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été
constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement le
rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi
de diriger le rayon vers les yeux d’un observateur, même à travers des surfaces
réfléchissantes (miroirs, par exemple).

xi

ESPAÑOL

Las informaciones siguientes son presentadas en conformidad con las disposiciones
de las autoridades internacionales y se refieren al uso correcto del PDA.

NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a la
fecha de producción: CDRH 21 CFR 1040 y EN 60825-1.
No es necesario abrir el aparato para la instalación, la utilización o la manutención.

La utilización de procedimientos o regulaciones diferentes de
aquellas describidas en la documentción puede causar una

ATENCIÓN

exposición peligrosa a la luz láser visible.

El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los ojos
humanos a consecuencia de una exposición de corta duración. Eviten de mirar fijo el
rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por
ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos de un
observador, también a través de superficies reflectantes como los espejos.

LED Illuminator

The use of an illuminator in the Datalogic Jet™ Imager is a Class 1 LED product:

xii

ILLUMINATORE LED CLASSE 1
AUSLEUCHTER LED KLASSE 1
ILLUMINATEUR A LED DE
CLASSE 1
ILUMINADOR LED DE CLASE 1

RADIO COMPLIANCE

In radio systems configured with PDAs and access points, the frequencies to be used
must be allowed by the spectrum authorities of the specific country in which the
installation takes place. Be absolutely sure that the system frequencies are correctly
set to be compliant with the spectrum requirements of the country.

The Radio modules used in this product automatically adapt to the frequencies set by
the system and does not require any parameter settings.

The following shows the correspondence between the Datalogic Jet™ models and
the Radio modules:

 Datalogic Jet™ 5XX-XXX 802.11b (Wi-Fi) radio card
 Datalogic Jet™ X1X-XXX GSM/GPRS Tri-band (900, 1800, 1900 MHz)

module

 Datalogic Jet™ 51X-XXX 802.11b (Wi-Fi) radio card + GSM/GPRS Tri-

band (900, 1800, 1900 MHz) module

INFORMATION FOR THE USER

ENGLISH

Contact the competent authority responsible for the management of radio frequency
devices of your country to verify the eventual necessity of a user license. Refer to the
web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm

ITALIANO

Prendi contatto con l'autorità competente per la gestione degli apparati a radio
frequenza del tuo paese, per verificarne l'eventuale necessità della licenza d'uso.
Inoltre puoi trovare ulteriori informazioni al sito:

http://europa.eu.int/comm/enterprise/rtte/spectr.htm

FRANÇAIS

Contactez l'autorité compétente en la gestion des appareils à radio fréquence de
votre pays pour vérifier la nécessité du permis d'usage. Pour tout renseignement
vous pouvez vous adresser au site web:

http://europa.eu.int/comm/enterprise/rtte/spectr.htm

DEUTSCH

Um die Notwendigkeit der Verwendungslizenz zu prüfen, wenden Sie sich an die
Behörde, die auf der Radiofrequenzgerätsführung Ihres Lands bewandert ist. Weitere
Informationen sind verfügbar auf dem Web Site:

http://europa.eu.int/comm/enterprise/rtte/spectr.htm

.

.

.

for further information.

xiii

ESPAÑOL

Contacta con la autoridad competente para la gestión de los dispositivos de radio
frecuencia de tu país, para verificar si es necesario la licencia de uso. Además se
puede encontrar mas información en el sitio web:

http://europa.eu.int/comm/enterprise/rtte/spectr.htm

.

FCC

This device must be opened by qualified personnel only.

Modifications or changes to this equipment without the expressed
written approval of Datalogic could void the authority to use the
equipment.

This device complies with PART 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference which may cause undesired operation.

All Wi-Fi models contain FCC ID H9PLA4137.

WARNING: FCC RF EXPOSURE GUIDELINES

To satisfy FCC RF exposure compliance requirements, this device should be used in
hand-held, hand-operated configurations only. The device and its antenna must
maintain a separation distance of 20 cm or more from a person’s body, except for the
hands and wrists, to satisfy RF exposure compliance.
This device is designed to be used in a person’s hands and its operating
configurations do not support normal transmissions while it is carried in pockets or
holsters next to a person’s body.

This device must not be co-located or operated in conjunction with any other
transmitting device.

COMPLIANCE

xiv

GENERAL VIEW

A

J

I

E

H

A) Data capture/Laser Output window
B) Scan Key(s) (3)
C) Bluetooth®
D) Charging status LED
E) Backlit keyboard
F) External Power Supply Connector
G) Communication/Charger Connector
H) Headset jack
I) User Programmable LED

G

F

LED

B

C

D

Q

P

O

N

M

J) Backlit display
K) Adjustable elastic strap with stylus

holder
L) Microphone
M) Latch release button
N) Battery latch
O) Battery pack
P) Speaker
Q) IrDA port

K

L

xv

xvi

INTRODUCTION

1

1 INTRODUCTION

1.1 DATALOGIC JET™ PDA DESCRIPTION

Datalogic Jet™ is a professional PDA that extends the power of enterprise computing
to all areas of supply chain management: from planning and production, to
warehousing and transportation. Datalogic’s PDA captures, computes and
communicates information anywhere and anytime, and offers the most versatile
business solution for any warehouse management system.

Key features include fully integrated automatic data capture (1D bar code, 1D bar
code & RFID HF-ISO tags, 1D & 2D bar codes & Image) and superior wireless
communication capabilities (Bluetooth®, Wi-Fi 802.11b, GSM/GPRS) as well as a
winning combination of unique Italian design, compact size, light weight, and great
ergonomics all in a sturdy outer casing.

Datalogic Jet™ enables companies and organizations worldwide to make more
effective use of people and tools for receiving, storage, and shipping activities. For
example, extended mobility allows simultaneous real-time inventory management
and control of all stock movements to increase precision while minimizing operating
costs. Data on store shelves, inventory levels and storage bins is immediately
available to permit greater coordination and cut flow times.

Datalogic Jet™ provides mobile professionals with the most relevant features needed
to operate in demanding environments: reliability, ruggedness, drop resistance, long
lasting batteries, flexible communication and efficient data capture.

1.2 AVAILABLE MODELS

The brand new Datalogic Jet™ PDA is available in different models depending on
the options it is equipped with. All options are listed below:

• data capture options: laser, imager, laser + RfId

• communication options: Wi-Fi 802.11b, GSM/GPRS, Bluetooth®

• data entry options: standard keyboard, function oriented keyboard

For further details about the Datalogic Jet™ PDA models refer to the web site:
http://www.datalogic.com

.

1

1

DATALOGIC JET™

1.3 PACKAGE CONTENTS

The Datalogic Jet™ PDA package contains:

− 1 Datalogic Jet™ PDA;

− 1 CD-ROM Datalogic-NET SDK (Windows CE.NET SDK for Datalogic terminals)

− 2 styluses

− 1 user’s manual

− 1 rechargeable battery pack;

− 1 adjustable elastic strap with stylus holder

− 1 belt clip

− 1 belt clip pivot

Any other packages will contain the accessories necessary for the Datalogic Jet™
PDA connection to the host computer and to the network: the cradle, power supply,
and one or more connection cables.

Remove all the components from their packaging, check their integrity and congruity
with the packing documents.

CAUTION

NOTE

2

Keep the original packaging for use when sending products to the
technical assistance center. Damage caused by improper
packaging is not covered under the warranty.

Rechargeable battery packs are not initially charged. Therefore the
first operation to perform is to charge them. See paragraph 4.1.

INTRODUCTION

1.4 ACCESSORIES

 Cradles

94A151096 Datalogic Jet™ Single Cradle Desk (includes slot for spare battery
pack recharge; RS232 and USB communications).
94A151097 Jet™ Single Cradle Vehicle Hands-Free.
94A151100 Jet™ Single Cradle Vehicle Standard.

 Charger

94A151098 Datalogic Jet™ Multi-Battery pack Charger (4 slots).

 Batteries

94ACC1293 Datalogic Jet™ Standard Battery pack (Li-Ion battery pack 1070

mAh@7.4 V).

94ACC1294 Datalogic Jet™ Large Capacity Battery pack (Li-Ion battery pack

1800 mAh@7.4 V).

 Power Supply

94ACC1286 PG12-10P35 AC/DC Power Supply without cord for Datalogic Jet™.
94ACC1296 PG12-10P35 AC/DC Power supply EU KIT
94ACC1297 PG12-10P35 AC/DC Power supply UK KIT
94ACC1298 PG12-10P35 AC/DC Power supply US KIT
94ACC1299 PG12-10P35 AC/DC Power supply AUS KIT

94ACC4595 FPS18 Power Supply without cord for Datalogic Jet™ Single Cradle
Desk and for Datalogic Jet™ Multi-Battery Charger

94ACC1150 Power cord EU 3-pin
94ACC1160 Power cord AUS 3-pin

 Cables

94A051008 WIN-NET SERIAL CABLE (HRS 3500-16P-CV) cable for RS232
direct connection between the PDA and the PC.

94A051009 WIN-NET USB CABLE (HRS 3500-16P-CV) cable for USB direct
connection between the PDA and the PC.

94A051013 WIN-NET VEHICLE PWR CAB (CRADLE) cable for powering
vehicle cradle from the car cigarette lighter.

 Various

94ACC1287 Datalogic Jet™ Belt Holster.
94ACC1288 Datalogic Jet™ Functional Case.
94ACC1300 Datalogic Jet™ Backstrap Kit (2 pcs)
94ACC1301 Stylus Pen (20 pcs)

1

3

2

A

DATALOGIC JET™

2 CONNECTIONS

2.1 PDA CONNECTION TO THE HOST COMPUTER

2.1.1 RS232/USB Direct Connection

You can use a cable to connect the Datalogic Jet™ PDA to a host computer to
transfer data.

C

B

D*

Key:

A Host computer C RS232 cable or USB cable
B Datalogic Jet™ PDA D *Power Supply

* Recommended Power Supply: PG12-10P35 AC/DC Power Supply

USB communication may not be completely guaranteed while
batteries are simultaneously in charge. Avoid the power supply

CAUTION

4

connection when the USB link is active.

(only necessary for battery charging)

CONNECTIONS

2

2.1.2 WLAN Connection

Datalogic Jet™ Wi-Fi models can communicate with the host using the on-board
radio frequency module and an Access Point connected to the host computer.

A

B

Key:
A) Datalogic Jet™ PDA
B) Access point

In order to avoid wasting power, the Wi-Fi module is off by default. If
you need to have the Wi-Fi module working, the module must be
powered on using the Wireless Communications applet (see par.

NOTE

3.7.4). To start configuring your WLAN connection, tap the Wi-Fi icon
at the bottom of the screen.

5

2

2.1.3 WPAN Connections

Datalogic Jet™ PDAs can communicate with a Bluetooth
within a range of 10 m, using the on-board Bluetooth

®

module.

DATALOGIC JET™

®

device, such as a printer,

A

B

Key:

A) Datalogic Jet™ PDA

®

B) Bluetooth

printer

In order to avoid wasting power, the Bluetooth® module is off by
default. If you need to have Bluetooth® working, the module must be
powered on using the Wireless Communications applet (see par.

NOTE

3.7.4), and perform the Discovery procedure (see par. 3.8.2).

The Blue LED flashing signals that the Bluetooth® module is on.

6

CONNECTIONS

2

2.1.4 WWAN Connections

Datalogic Jet™ GSM/GPRS models enhance your connectivity solutions giving you
an opening to an international wireless infrastructure that is the standard in Europe
and Asia.

GSM (Global System for Mobile communications), is a digital mobile phone system
based on TDMA; it utilizes the 900, 1800 and 1900 MHz bands.

GPRS supports IP (Internet Protocol) and allows accessing Internet and Intranet
services, such as sending and receiving e-mail or Web browsing.

In order to use a WWAN Connection you have to install a SIM Card (see instructions
on the following page).

In order to avoid wasting power, the GSM/GPRS module is off by
default. If you need to have GSM/GPRS working, the module must
be powered on using the Wireless Communications applet (see par.

NOTE

3.7.4.

7

2

Installing the SIM Card

DATALOGIC JET™

SIM Card Slot

Locking

Plate

To correctly insert the SIM Card, proceed as follows:

1- Turn off the Datalogic Jet™ PDA.

2- Press the latch release button and pull the battery latch down as indicated in the

figure below:

8

CONNECTIONS

2

3- After removing the battery pack, open the Sim Card slot by pulling up the locking

plate.

4- Pull up the card holder and insert the Sim Card with its contacts downwards and

its round corner at the bottom.

5- Lock the card into place by pushing the card holder down and then pulling the

locking plate down.

Removing the SIM Card

To remove the SIM card, follow the steps above to access the SIM area, and remove
it from its slot.

9

2

2.2 CONNECTION CABLES

The following cables are listed with their order number.

RS232 Direct Connection:



94A051008 WIN-NET SERIAL CABLE (HRS 3500-16P-CV)

Datalogic Jet™

HOST/PC side

side

16-pin

5

6 2

7

8

9

11

10

13

RX

TX

CTS

RTS

DSR

DTR

GND

 USB Direct Connection:

94A051009 WIN-NET USB CABLE (HRS 3500-16P-CV)

Datalogic Jet™

side

16-pin

13

14

15

16

GND

V+

D+

D-

 Power Supply Polarity:

VEXT

9-pin

(female)

HOST/PC side

9-pin

(female)

DATALOGIC JET™

3

7

8

4

1

6

5

4

1

3

2

10

GND

USE AND FUNCTIONING

3

3 USE AND FUNCTIONING

The use of the Datalogic Jet™ PDA depends on the application software loaded.
However there are several parameters that can be set and utilities that can be used
to perform some basic functions such as data capture, communications, file
management, etc.

3.1 PDA STARTUP

The Datalogic Jet™ PDA turns on when the battery pack or the external supply is
inserted.

After the battery pack is installed, use the [ON/OFF] key to turn the PDA on and off.

As soon as the PDA is on, the Windows CE .NET desktop configuration will appear
on the screen. Wait a few seconds before starting any activity so that the PDA
completes its startup procedure.

Use the stylus as suggested in paragraph 3.2 to select icons and options.

11

3

DATALOGIC JET™

The PDA goes into power-off (low power with display and keyboard backlight off),
when it is no longer used for more than a programmable timeout, which is defined in
the POWER applet of the Control Panel. In this mode it can be awakened (resuming
operation) by the [ON/OFF] key.

The PDA can also be awakened or turned off by the application
program.

NOTE

3.2 USING THE STYLUS

The stylus selects items and enters information. The stylus functions like a mouse.

Tap:

Drag:

Tap-and-hold:

The stylus is factory aligned; however, it is possible to align the cursor on the screen
with the tip of the stylus. Enter the STYLUS applet of the Control Panel and tap the
center of each target that appears on the screen with the tip of the stylus.

Touch the screen once with the stylus to open items and select
options.

Hold the stylus on the screen and drag across the screen to
select text and images. Drag in a list to select multiple items.

Tap and hold the stylus on an item to see a list of actions
available for that item. On the pop-up menu that appears, tap the
action you want to perform.

12

USE AND FUNCTIONING

3

3.3 DATA CAPTURE

To configure and enable data capture parameters refer to par. 3.6.

3.3.1 Laser Data Capture

To scan barcodes, point the Datalogic Jet™ PDA laser model onto the code from a
distance within the reading range while pressing one of the three SCAN Keys. See
the reading diagrams in par. 5.2 for the reading range of your model.

The lighted band emitted by the laser must completely intercept the barcode as
shown in the figure below. If enabled, the emission of an acoustic signal will indicate
that the scan has taken place correctly.

NO

OK

NO

OK

13

3

DATALOGIC JET™

3.3.2 Imager Data Capture

To read a 1D or 2D code, simply point the Datalogic Jet™ Imager model onto the
code from a distance within the reading range (See par. 5.1, section Datalogic Jet™
Imager Optical Features) and press one of the three SCAN Keys.

The Datalogic Jet™ Imager uses an intelligent aiming system similar to those on
cameras, which creates a field of view where the code is to be positioned:

Aiming System

If the aiming system is centered and the entire symbology is within the aiming system
as shown below, either wait for the timeout or release the Scan Key.

A red beam illuminates the code, which is captured and decoded. You will get a good
read.

14

USE AND FUNCTIONING

Linear barcode 2D Matrix symbol

ÌBX3ÉÎ

3

Relative Size and Location of Aiming System Pattern

The field of view changes size as you move the reader closer or farther away from
the code. The field of view created by the aiming system will be smaller when the
Datalogic Jet™ Imager is closer to the code and larger when it is farther from the
code.

Symbologies with smaller bars or elements (mil size) should be read closer to the
unit. Symbologies with larger bars or elements (mil size) should be read farther from
the unit. (See par. 5.1 for further details).

3.3.3 RFID Data Capture

To read or write a tag, place the Datalogic Jet™ PDA so that the RFID emission
window is in front of and almost in contact with the tag, then press one of the three
SCAN Keys or the application defined key.

15

3

DATALOGIC JET™

3.4 DESCRIPTION OF THE KEYS

The Datalogic Jet™ PDA provides two different keyboards (Standard keyboard and
Function Oriented keyboard) having a total of 27 keys each.
The keyboard can be divided as follows (the Datalogic Jet™ PDA model shown in
the following figure is taken as an example):

2 Lateral

SCAN keys

(1 per side)

System Control

and

Navigation Keys

General keys

Power Key

3.4.1 System Control and Navigation Keys

Standard Keyboard

Powers the PDA ON or OFF.

They let you move forwards or backwards within the

16

Internet Explorer browser pages.

USE AND FUNCTIONING

3

They let you move forwards, backwards, upwards or
downwards within Text fields; scroll through a Menu list
or browse among folder files.

Switches on/off the keyboard backlight. The backlight
automatically turns off after a set timeout.

Esc

Esc

SCAN

Esc

SCAN

Act

Function Oriented Keyboard

Powers the PDA ON or OFF.

They let you move forwards or backwards within the
Internet Explorer browser pages.

They let you move forwards, backwards, upwards or
downwards within Text fields; scroll through a Menu list
or browse among folder files.

By pressing these keys simultaneously,
a system software reset is performed.

By pressing these keys simultaneously,
a system hardware reset is performed.

Switches on/off the keyboard backlight. The backlight
automatically turns off after a set timeout.

By pressing these keys simultaneously,
a system software reset is performed.

By pressing these keys simultaneously,
a system hardware reset is performed.

17

3

DATALOGIC JET™

3.4.2 Key Selection

Standard Keyboard

The following figure shows the Datalogic Jet™ standard keyboard:

Some of these keys carry extra symbols and are logically divided in up to 3 sections
according to the following figure:

Esc Act

SCAN

-Symb-

ghi

pqrs

Bksp

A

abc

jkl

tuv

Start

def

EnterEnter

mno

wxyz

ALPHA

Esc

jkl

B

C

Each section corresponds to a symbol that can be obtained using the corresponding
keyboard method according to the following scheme:

A) function of the key when simultaneously pressed along with the Blue key;
B) function of the key when directly pressed;
C) function of the key when in Alpha mode, in order to digit all the alphabetic

characters positioned over the keys.

18

USE AND FUNCTIONING

Act

Start

SCAN

3

By default it launches the Internet Explorer browser but
you can use the SDK to appropriately launch any
Application Program.

It opens the Start Menu.

It starts Data capture.

The BLUE key pressed simultaneously along with any
other keyboard key enables the character positioned
above or at its right/left side (in case of keys displayed at
the top of keyboard).

Ex: BLUE key +

5 jkl key corresponds to the character.

NOTE

-Symb-

key, you can scroll through a list of punctuation signs and
symbols and select the desired one by a timeout.

It enters a special mode through which it is possible to
digit all the alphabetic characters positioned over the keys.

When in alphanumeric mode, by pressing repeatedly the

ALPHA

Ex: 7pqrs in alphanumeric mode: press once for ‘p’, twice
for ‘q’, three times for ‘r’, four times for ‘s’. To exit the
Alpha mode and return to the keyboard normal functioning
it is necessary to press the Alpha key again.

It locks and unlocks the Keyboard.

It corresponds to pressing ALT-F on a standard PC
running Windows, that is it opens the first entry of a drop
down Menu.

Switches on/off the keyboard backlight. Both display and
keyboard backlights automatically turn off after a timeout,
depending on Control Panel settings.
The backlights automatically turn off after a set timeout.

Once the Alpha mode has been entered, press the Alpha key again
to exit this mode.

19

3

DATALOGIC JET™

Function Oriented Keyboard

The following figure shows the Datalogic Jet™ function oriented keyboard:

Some of these keys carry extra symbols and are logically divided in up to 3 sections
according to the following figure:

A

B

C

Each section corresponds to a symbol that can be obtained using the corresponding
keyboard method according to the following scheme:

D) function of the key when simultaneously pressed along with the Orange key;
E) function of the key when directly pressed;
F) function of the key when in Alpha mode, in order to digit all the alphabetic

characters positioned over the keys.

20

USE AND FUNCTIONING

3

It starts Data capture.

The ORANGE key pressed simultaneously along with any
other keyboard key enables the character positioned
above or at its right/left side (in case of keys displayed at
the top of keyboard).

Ex: ORANGE key +

5 jkl key corresponds to the

When in alphanumeric mode, by pressing repeatedly the
key, you can scroll through a list of punctuation signs and
symbols and select the desired one by a timeout.

It enters a special mode through which it is possible to
digit all the alphabetic characters positioned over the keys.
Ex: 7pqrs in alphanumeric mode: press once for ‘p’, twice
for ‘q’, three times for ‘r’, four times for ‘s’. To exit the
Alpha mode and return to the keyboard normal functioning
it is necessary to press the Alpha key again.

It locks and unlocks the Keyboard.

It corresponds to pressing ALT-F on a standard PC
running Windows, that is it opens the first entry of a drop
down Menu.

NOTE

Switches on/off the keyboard backlight. Both display and
keyboard backlight automatically turn off after a timeout,
depending on Control Panel settings.
The backlights automatically turn off after a set timeout.

Once the Alpha mode has been entered, press the Alpha key again
to exit this mode.

21

3

DATALOGIC JET™

3.5 STATUS INDICATORS

3.5.1 LED Status

The Datalogic Jet™ provides three different LEDs signaling the PDA status.

LED STATUS

General Purpose
(left-side)

Green/Red This LED is available to the application

program.

Bluetooth®

(extreme right -side)

Charging Status

(right side)

Blue blinking

Green pulse it goes on for a few seconds when the

Green blinking it blinks during slow charge.

Green constant it is constant once the charging process

Red blinking

Red constant it is constant while charging.

Green/Red they turn on alternatively while

Orange blinking it blinks when a charging error has

it blinks when the Bluetooth
on.

external supply or the battery pack
supply has been recognized.

has been completed.

it blinks when the battery pack is running
down.

discharging.

occurred, for example when the external
power is connected but no battery is
inserted.

® module is

22

USE AND FUNCTIONING

3

3.5.2 Status Bar

The Status Bar provides information about the time, the battery level, the keyboard
function, and the decoding status.

ICONS DESCRIPTION

Time and Battery Icons

It shows the time

They are representative of five different icons indicating the
battery level. The icon is green or red colored according to the
power left (green when >20%, red when <20%).

Keyboard Status Icons

Decoding Status Icons

It shows the battery is charging

It shows the Keyboard is in FUNC mode

It shows the Keyboard is in ALPHA mode

It shows the Keyboard is in Normal mode

It shows the Capslock is active

It shows the Keyboard is locked

It shows the decoder is active

It shows the decoder is not active

Status Bar

23

3

DATALOGIC JET™

3.6 DATA CAPTURE CONFIGURATION

From the Taskbar, tap the "Data Capture" icon to open a drop–down menu. Data
Capture can also be accessed from the Control Panel.

By selecting the
about the Scanner and the Software; the
applet (Data Capture Configuration Window), while

Info item from this drop-down menu you can access information

Configure item opens the configuration

Capture accesses the data

capture applet (Data Capture Window) which enables code reading.
The last menu item (

Wedge) enables Wedge Emulation.

3.6.1 Configure

The Configuration applet contains the barcode scanning configuration parameters in
a directory tree structure. The available barcode parameters are divided into two
groups: Reader Parameters and Scan Parameters.

The Reader Parameters depend on the type of scanner module installed on the PDA
and allow barcode configuration (i.e. enable/disable Code 39, check digit control,
etc.).

The Scan Parameters are common to all scanner modules and allow control of the
scanning device (i.e. beeper control, LED control, laser timeout, etc.).

Each Data Capture screen window corresponds to a branch of the tree, and the
name of the current branch is displayed at the bottom of each screen window.

24

USE AND FUNCTIONING

3

Data Capture Configuration Window

The screen format shows two columns where the left column indicates branches or
parameters. Branches have three dots in the right column (...). You can navigate
through the tree structure using the stylus or keyboard arrows directly on the item
field or from the menu.

Parameters have their corresponding current values in the right column. You can edit
parameter values using the stylus or keyboard arrows directly on the item field or
from the menu. To change a value for example, select the line of the value to be
changed, choose Edit from the Parameter Menu then choose a new value from the
values listed in the box (see following figures).

Selecting Data Capture Setup Parameters

25

3

DATALOGIC JET™

Alternatively using the stylus, you can tap once directly on the value on the right
column, continue tapping until the desired value is reached.

To activate a new configuration select the File ->Save Menu to send the new
configuration to the barcode decoding software and save the new configuration. This
will save the configuration to non-volatile memory preventing loss at the next system
reset.

Reader Parameters

The barcode reading parameters and values are dependent upon the type of scanner
module mounted in your PDA. For a detailed list of parameters and of their
configuration procedures, please refer to the SDK Help file on the CD.

Scan Parameters

The Scan Parameters are common to all scanner modules and allow control of the
scanning device. The Scan parameters are described as follows:

Scan Timeout: the maximum time, in milliseconds, during which the scanner

remains on without decoding any barcode.

Beep Duration: the time interval, in milliseconds, during which the beeper will sound

when the scanner reads a code. To disable the beeper, set this value to 0.

Beep Frequency: determines the frequency in Hertz of the beeper.

Continuous Mode: when enabled, the scanner can only be turned off by releasing

the SCAN key, or if Soft Trigger is enabled, by the application program. Continuous
Mode overrides Scan Timeout.

Keyboard Emulation: if enabled all scanned data are transformed into keyboard

events and can therefore be displayed and saved to a file as if input from the PDA
keyboard.

Soft Trigger: when enabled, the laser can be turned on/off by the application

software.

Scan Always On: enables the scanner for barcode reading independently from the

application software.

26

USE AND FUNCTIONING

3

Default Settings

The following tables contain the default values for the major barcode setup
parameters, according to the type of scan engine mounted on the PDA. For a
complete list of parameters and of their configuration procedures, please refer to the
SDK Help file on the CD.

SCAN PARAMETERS HP Laser Imager RFID+Laser

Scan Timeout 5000 Not available 5000
Beep Duration 20 20 20

Beep Frequency 2000 2000 2000
LED Duration 0 0 0
LED Pulses 0 0 0
Continuous Mode Disabled Disabled Disabled
Keyboard Emulation Disabled Disabled Disabled
Soft Trigger Enabled Enabled Enabled
Scan Always On Disabled Disabled Disabled

BARCODE SYMBOLOGY
SPECIFIC
READER PARAMETERS

UPC A
UPC E
EAN 8
EAN 13
UPC E1
EAN Bookland
UPC/EAN/JAN
Code 39
Code 39 Full ASCII
Code 32
Code 39 Trioptic
2/5: Interleaved
2/5: Industrial
2/5: Matrix
Code 128
EAN 128
ISBT 128
Codabar

*In the Imager models these codes may only be enabled or disabled as a group by
the UPC/EAN/JAN family selection (see a few lines below).

HP Laser Imager RFID+Laser

Enabled Enabled
Enabled Enabled
Enabled Enabled
Enabled

*

Enabled
Disabled
Disabled
Enabled
Enabled Enabled Enabled
Disabled Disabled Disabled
Disabled Disabled
Disabled
Enabled Enabled Enabled
Disabled Disabled
Disabled
Enabled Enabled Enabled
Enabled Disabled Enabled
Disabled
Enabled Enabled Disabled

27

3

DATALOGIC JET™

BARCODE SYMBOLOGY
SPECIFIC

HP Laser Imager RFID+Laser

READER PARAMETERS
MSI
Plessey

Code 93
Code 11
PDF - 417
Data Matrix
QR
POSTNET
PLANET
Japan Post
Australia Post
KIX Code
Royal Mail Code (RM4SCC)

Enabled Disabled
Disabled
Disabled Enabled Disabled
Disabled
Enabled
Enabled
Enabled

Disabled*

*These codes may be enabled individually but are disabled as a group.

RFID SYMBOLOGY PARAMETERS RFID+Laser
Data Type I.CODE Iso-15693
Read Type Identifier

3.6.2 Capture

The Data Capture applet (Capture) enables code reading.

28

Data Capture Window

USE AND FUNCTIONING

3

Data Capture can also be enabled through the Configuration applet by selecting File

->Scanner from the main menu, or by enabling the parameter Scan Always On in the
Scan Parameters branch.

Enabling the Data Capture

3.7 CONTROL PANEL

From the Desktop, double tap on the "Control Panel" icon to open the Windows CE
.NET control panel main window. The Control Panel can also be launched from Start

->Settings ->Control Panel.
APPLET programs are displayed as icons; one icon corresponds to each APPLET.

Control Panel

29

3

DATALOGIC JET™

3.7.1 Buttons

The BUTTONS Applet allows assigning desired applications to be launched by the
Act button or one of the function keys (F1, F2, F3).

3.7.2 Registry

The REGISTRY ADMIN applet provides management of Windows CE .NET registry.
Select the REGISTRY ADMIN applet by double tapping the Registry Admin icon.
The Registry Administration Main window appears. Two functions are available:

- Save Registry allows permanently saving the Windows configuration (example:
custom configuration of screen desktop background color, or network adapter
configuration) to non-volatile memory (SAVE button).

- Restore Default Registry allows restoring the initial factory default configuration
(Restore Default button). After restoring the factory default configuration, you
must perform a software reset (see par. 3.4.1).

Saving the registry to non-volatile memory guarantees the persistence of the
Windows configuration in case of battery pack replacement.

30

Registry Administration Window

USE AND FUNCTIONING

3

3.7.3 Files Admin

The FILES ADMIN applet enables control of the permanence of files in the System
Folder. Two functions are available on the Files Admin Main window by means of two
buttons:

Files Admin Main Window

Save Session: with this button all files will be permanently saved in the \Windows

directory in non-volatile memory. This function guarantees the steady maintenance of
every file produced during the current working session - even of sub-directories and
relevant files - with the exception of the files belonging to the FLASH image.
These current working session files will be backed-up in the \Backup\Windows
directory.
At the next hardware reset, the files previously saved in the \Backup\Windows
directory will be restored to the Windows directory (see par. 3.9).

Safe Setup: with this button, the installation of software programs will be saved to

non-volatile memory (Backup directory). Before doing this, it will be checked that the
Backup directory has enough space to save the files. If the directory space is not
enough, an error message will be shown and the program will exit the Safe Setup
function.

Two activating procedures are available for Safe Setup :

- Select an installation file (for example, a .CAB cabinet file) from the Safe Setup

mask.

31

3

DATALOGIC JET™

Safe Setup First Mask

Then select \Windows or a relevant sub-directory in the path box. Then, Safe Setup
will recognize the new files and directories present in the \Windows directory, and will
copy them to the \Backup\Windows directory. At the next hardware reset, these files
will be restored (see par. 3.9).

- Simply skip the first mask either by closing it or by pressing the ESC key. When it

closes, a new mask will pop up: it will enable any type of installation (even remote
ones like ActiveSync

®

installations). Make sure the installation directory is \Windows
or one of its sub-directories. After installation, tap OK: Safe Setup will save the new
files in the \Backup\Windows directory.

32

Safe Setup Second Mask

USE AND FUNCTIONING

3

3.7.4 Wireless Communications

The WIRELESS COMMUNICATIONS applet provides management of the Wi-Fi
Card and of the Bluetooth

®

and GSM/GPRS modules.

Select the WIRELESS COMMUNICATIONS applet by double tapping the Wireless
Communications icon. The following window will appear:

Wireless Communications Window

In order to avoid wasting power, all modules are off by default.

NOTE

33

3

DATALOGIC JET™

3.8 WINDOWS CONNECTIONS

From the Desktop, double tap on the "Connections" folder to open the following
window:

Windows Connections

3.8.1 Microsoft® ActiveSync®

Microsoft
your Datalogic Jet™ PDA and synchronize the information on them. Synchronization
compares the data on the Datalogic Jet™ PDA with that on the desktop computer
and updates both computers with the most recent information.

With ActiveSync

- Back up and restore Datalogic Jet™ PDA data.

- Copy files between Datalogic Jet™ PDA and desktop computer.

- Synchronize files by selecting a synchronization mode.

It is possible to constantly synchronize while connected to a desktop computer or,
alternatively, synchronization can be performed only when the synchronize command
is chosen. You can select which information types are synchronized and control how
much data is synchronized.

®

ActiveSync® gives you the possibility to connect your desktop computer to

®

, it is possible to:

NOTE

34

By default, ActiveSync® does not automatically synchronize all types
of information. Use ActiveSync
and off for specific information types.

®

options to turn synchronization on

USE AND FUNCTIONING

3

For example:
Synchronize Microsoft Word and Microsoft Excel files between the Datalogic Jet™
PDA and the desktop computer. The files will automatically be converted to the
correct format.

You can establish a connection by Serial cable, by USB cable or by network.
Moreover, if you have a Datalogic Jet™ Single Cradle you can connect your
Datalogic Jet™ PDA putting it into the cradle and using a standard A-B USB cable or
a standard Serial null modem cable.

Visit the following Microsoft Web site for the latest in updates, technical
information, and samples:
http://www.microsoft.com/windowsmobile/resources/downloads

NOTE

ActiveSync® Remote

After a Partnership between PDA and desktop computer is established, it is also
possible to establish a remote connection via Wireless LAN: disconnect the actual
connection via ActiveSync
the taskbar and press Disconnect, then go to the \Windows\Desktop\Connection
folder and double tap the ActiveSync
it will be possible to choose a method to connect to the desktop computer. Choose
Network Connection and press the Connect button:

To set up your network connection you have to correctly set up your
wireless connection. These settings depend on the wireless card that
you have installed on your Datalogic Jet™ PDA and on your wireless

NOTE

network settings. For more information about these settings contact
your network administrator.

®

by double tapping the ActiveSync® connection icon on

®

remote icon. In the dialog box that will appear

35

3

DATALOGIC JET™

3.8.2 Bluetooth® Manager Device Setup

In order to enable a Bluetooth
PDA you must perform the discovery procedure and enable the device as follows:

1. Place the Bluetooth

meters).

2. From the “Connections” folder double tap on the “Bluetooth” applet to open the

Bluetooth

®

Manager Device window:

®

device for communication with the Datalogic Jet™

®

device within the range of the Datalogic Jet™ PDA (10

36

USE AND FUNCTIONING

3

3. Tap on the “Me” button to enter the related window; then, tap on the “ON” button

to activate the Bluetooth

®

module. The module activation may be also performed

by using the WIRELESS COMMUNICATION applet as described in par. 3.7.4.

By tapping on the “HW Details” and “SW Details” buttons, information
about the PDA Bluetooth
“Enable Encryption” button starts encryption of the Bluetooth
data. If tapping on the “Close” button the Bluetooth

®

hardware and software will be displayed, while the

®

communication

®

Manager Device

window will be closed.

4. Tap on the “Discovery” button to enter the related window; then, tap on the

“Scan” button to run the Discovery procedure:

37

3

DATALOGIC JET™

Once the Discovery procedure has been completed, select the desired
Bluetooth
the Bluetooth

®

device from the list. It is also possible to digit (12 hexadecimal digits)

®

address of the desired device by tapping on the “Add”

button. The “Clear” button deletes all discovered devices from the list.

5. Once the desired Bluetooth

Wizard” button to enter the related window where selecting the connection type
to be used for communication with the Bluetooth

®

device has been selected, tap on the “Connection

®

device:

The “Serial Port” button starts communication through the Bluetooth
COM 5 (typically used for connection with GPS devices).
The “Printer” button starts communication with a printer through the Bluetooth

®

serial port

®

serial port COM 5.
The “Kbd Emulation” button allows connection with a barcode reader using the
keyboard emulation.
The “ActiveSync” button starts communication with a PC equipped with a
Bluetooth

®

antenna and the related ActiveSync.

®

6. Hide the Bluetooth

Manager Device window by tapping on the icon
available on each window or close it through the “Close” button available in the
“Me” window (see step 3 of this procedure).

38

USE AND FUNCTIONING

3

3.9 BACKUP DIRECTORY FILE MANAGEMENT

All of the Windows CE .NET system files reside in RAM (volatile memory) except for
the Backup directory, which resides in FLASH (non-volatile memory). Therefore the
contents of the Backup directory are persistent even if the PDA is re-booted or the
battery pack is changed.

You can save your more important files that you don't want to lose due to PDA re­boot, in the Backup directory or create a sub-directory within Backup.

Even though the Windows Directory resides in RAM, it often contains files or sub­directories created by the user or by installation programs that you don't want to lose
at re-boot. To keep these files persistent it is necessary to copy them to the directory
\Backup\Windows. This directory doesn't exist originally (only Backup exists), and
therefore it must be created. At the next hardware reset, before activating the shell,
Windows CE .NET will copy the contents including all sub-directories of
\Backup\Windows to \Windows.

Likewise, to maintain files that must be run at Windows CE .NET startup, (i.e. .exe,
.lnk, .vb, .htm, etc.), it is necessary to copy them to the directory \Backup\Startup.
This directory does not exist originally (only Backup exists), and therefore it must be
created. The application programs will be run after any type of re-boot (both software
and hardware reset).

As an alternative to the Safe Setup function, it is possible to copy the .cab files to the
directory \Backup\Cabfiles (the Cabfiles sub-directory doesn't exists originally and
must therefore be created) and perform a PDA cold boot to have the application
installed. Once these files are copied to the directory \Backup\Cabfiles, the
application will be run after each re-boot.

From the second cold boot on, a message may be displayed such as "<application
name> is already installed. Re-install?". This message blocks the boot process.
Press the [Enter] key to continue the system initialization.

39

4

DATALOGIC JET™

4 MAINTENANCE

Rechargeable battery packs are not initially charged. Therefore the
first operation to perform is to charge them. See below.

NOTE

4.1 CHARGING THE BATTERY PACK

The battery pack autonomy varies according to factors, such as the frequency of
barcode scanning, RF usage, etc.

When the battery pack is low, the red LED positioned at the left side of the display
blinks.

It is possible to recharge the battery pack by using the PG12-10P35 AC/DC external
power supply directly connected to the Datalogic Jet™ PDA, see par. 2.1.1.

Alternatively, it is also possible to recharge the battery pack by using the Datalogic
Jet™ Single Cradle Desk or the Datalogic Jet™ Single Cradle Vehicle.

The charging process is signaled by a bi-colored charging status LED positioned at
the right side of the display (see par. 3.5).

If the battery pack is removed from the PDA, it can be recharged by inserting it into
the Datalogic Jet™ Multi-Battery pack Charger.

If the battery pack is new or has not been recharged for a long time,
it is necessary to perform two or three charging and discharging
cycles (complete use) before it can reach its maximum charge
capability.

CAUTION

The maximum time required to recharge a completely run-down
battery pack is about 2.5 hours for Li-Ion batteries.

40

MAINTENANCE

4

4.2 REPLACING THE BATTERY PACK

To correctly replace the battery pack, proceed as follows.

1. Turn off the Datalogic Jet™ PDA.

2. Press the latch release button and pull the battery latch down as indicated in the
figure below:

3. Remove the battery pack.

41

4

A

4. Replace the battery pack by pressing
the latch release button and pulling
the battery latch down (A), and then
by inserting it towards the speaker (B)
and pressing it into the Datalogic
Jet™ PDA until the battery latch is
automatically closed:

DATALOGIC JET™

B

When the latch release button is pressed, the PDA automatically
shuts off, in order to retain data during the pack substitution. After
the new pack insertion, be sure that the battery latch has

CAUTION

completely slid over the pack so that the latch release button is
released.

Risk of explosion if the battery is replaced by an incorrect
type. Dispose of the batteries as required by the relevant laws

WARNING

in force.

In order to guarantee an adequate operating autonomy, when
replacing the battery pack the PDA checks the battery energy level.
If the battery is not sufficiently charged, Datalogic Jet™ does not
turn on (when pressing the ON button).

NOTE

In this case, either substitute the battery pack with a charged one
(sufficiently charged) or insert Datalogic Jet™ into a powered cradle
or plug it into the direct power supply.

4.3 CLEANING THE PDA

Periodically clean the Datalogic Jet™ PDA with a slightly dampened cloth.
Do not use alcohol, corrosive products or solvents.

42

TECHNICAL FEATURES

5

5 TECHNICAL FEATURES

5.1 TECHNICAL DATA

Datalogic Jet™ Common Features

Electrical Features

Power
DC supply 14 V ± 5%
Battery pack 2 cell Li-Ion 1070 mAh@ 7.4 V (nominal)
Large capacity pack 2 cell Li-Ion 1800 mAh@ 7.4 V (nominal)
Internal backup battery Rechargeable Li-Ion 30 mAh

Communication Features Windows CE.NET COM Port

Optical interface IrDA 1.0 COM4
Serial interface RS232

Wireless Features

WLAN IEEE 802.11b DSSS
WPAN

WWAN GSM/GPRS Tri-band (900, 1800, 1900 mHz)

Environmental Features

Working temperature -10° to + 50 °C / +14° to +122 °F
Storage temperature -20° to +70 °C / -4° to +158 °F
Humidity 90% non condensing for temperatures<40°C
Protection IP64
ESD protection 4 KV contact discharge, 8 KV air discharge
Drop resistance 1.5 m / 5 ft

Hardware Features

FLASH 64 MB
RAM 64 MB
Microprocessor Intel XScale PXA 255 400 MHz
Audio Speaker, Microphone, Headset Jack
LED Two-color Programmable LED

Display 64K Color TFT LCD with 320 x 240 pixel resolution,

Keyboard 25 Plastic Top Backlit Keys plus Power Button plus 2

COM1

USB 1.1

Bluetooth

Radio with accessible SIM card interface

Charging Status (two-color LED)
Bluetooth

with LED backlight and touch screen

Lateral Push-buttons

® IEEE 802.15

® (blue LED)

COM6

43

5

DATALOGIC JET™

Mechanical Features

Dimensions (LxWxH) 17.6 x 9 x 2.8 cm / 6.9 x 3.5 x 1.1 in
Weight (depending on model) 424– 463 g / 14.9–16.3 oz (incl. battery)

Programming Features

Operating system Windows CE.NET 4.2

HP Laser models

Decoded barcodes 1D UPCA A; UPC E; EAN 8; EAN 13; Code 39;

Code 39 Full ASCII, Code 32, Interleaved 2 of
5; Industrial 2 of 5, Matrix 2 of 5, Code 128;
EAN 128; Codabar; MSI, Plessey, Code 93,
Code 11

RFID + Laser models

Decoded barcodes 1D UPC A; UPC E; UPC E1, EAN 8; EAN 13;

EAN Bookland, Code 39; Code 39 Full ASCII,
Code 32, Code 39 Trioptic, Interleaved 2 of 5;
Industrial 2 of 5, Code 128; EAN 128;
Codabar; MSI, Code 93

Decoded RFID Tags Gemplus FOLIO, Inside Pico Tag, Omron

V720, Philips I.Code, Microchip MCRF355,
MCRF360, Texas Instruments™ RFID Tag-it;
ISO 15693

Imager models

Decoded barcodes 1D UPC A; UPC E; EAN 8; EAN 13,

UPC/EAN/JAN; Interleaved 2 of 5; Code 39;
Code 39 Full ASCII, Codabar; Code 128; EAN

128; Code 93
Decoded barcodes 2D PDF417, DataMatrix , QR, MacroPDF
Postal codes POSTNET, PLANET, Japan Post, Australia

Post, KIX Code, Royal Mail Code (RM4SCC)

Datalogic Jet™ HP Laser / RFID +Laser Optical Features

Optical Features

Datalogic Jet™ HP

Laser

Datalogic Jet™ RFID

+Laser

Maximum resolution 0.13 mm / 5 mils 0.13 mm / 5 mils
Skew angle ± 55 ° ± 60°
Pitch angle ± 65° ± 65°
Scan rate - horizontal 35 ± 5 scan/sec 39 ± 3 scan/sec
Scan rate - vertical
Depth of field See reading diagrams on the next page
Light source laser scanner VLD, wavelength 630~680 nm
Safety class Class II EN 60825-1/CDHR

44

TECHNICAL FEATURES

5

Datalogic

Jet™ Imager Optical Features

Optical Features

Max. resolution
1D Codes 0.10 mm / 4 mils
2D Codes 0.17 mm / 6.6 mils
Skew angle ± 40 °
Pitch angle ± 35°

Depth of field*

1D (linear): X-dimension

Code39 0.13 (5) 1.2 (0.47) 8.0 to 15.0 (3.15 to 5.90)

0.50 (20) 3.2 (1.26) 8.0 to 33.0 (3.15 to 12.99)
EAN13 0.33 (13) 3.1 (1.22) 7.5 to 24.5 (2.95 to 9.65)
2D: X-dimension

POSTNET 0.5 (20) 4.0 x 0.4 (1.57 x 0.16) 11.5 to 30.0 (4.53 to

PDF417 0.13 (5) 1.1 x 0.9 (0.43 x 0.35) 8.5 to 15.5 (3.35 to 6.10)

0.17 (6.6) 1.4 x 1.2 (0.55 x 0.47) 7.0 to 19.0 (2.76 to 7.48)

0.25 (10) 2.2 x 1.8 (0.86 x 0.71) 4.5 to 24.0 (1.77 to 9.45)

QR 0.25 (10) 0.7 x 0.7 (0.28 x 0.28) 7.0 to 15.5 (2.76 to 6.10)

0.38 (15) 1.1 x 1.1 (0.43 x 0.43) 4.5 to 21.0 (1.77 to 8.27)

DataMatrix 0.19 (7.5) 0.8 x 0.8 (0.31 x0.31) 9.0 to 13.0 (3.54 to 5.12)

0.25 (10) 0.8 x 0.8 (0.31 x 0.31) 7.5 to 16.5 (2.95 to 6.50)

0.38 (15) 1.0 x 1.0 (0.39 x 0.39) 6.0 to 22.0 (2.36 to 8.66)

mm (mils)

mm (mils)

Symbol size

cm (in)

Symbol size

cm (in)

DOF

cm (in)

DOF

cm (in)

11.81)

Sensor 640 x 480 pixel element, 2D CMOS array
Illuminator LED array
Wavelength 630~670 nm
LED Safety

Class 1 to EN 60825-1
class
Aiming System Visible Laser Diode
Wavelength 650 nm
Laser Safety

Class 2 EN 60825-1; Class II CDHR
class

*Reading distances are measured from the nose of the reader.

45

5

5.2 READING DIAGRAMS

300

200

0.13 mm
(5 mils)

100

0

100

Datalogic Jet™ HP Laser

Reading Zones (10° skew

0.25 mm
(10 mils)

0.19 mm

(7.5 mils)

0.38 mm
(15 mils)

0.50 mm
(20 mils)

DATALOGIC JET™

1.00 mm
(40 mils)

200

300
mm

100 200 400

EAN

0.33 mm
(13 mils)

300 500

600

700 800 mm

Datalogic Jet™ RFID +Laser

Reading Zones (10° skew angle)

300

200

100

100

200

300
mm

0.50 mm
(

20 mils

0.25 mm
(

)

0.13 mm
(

5 mils

10 mils

)

0

100 200 400300

)

500 mm

1.00 mm
(40 mils)

46

TEST CODES

ÌtestwÎ

6 TEST CODES

0.25 mm (10 mils)

Code 39

High Density Codes

6

17162

2/5 Interleaved

Code 128

EAN 13

0123456784

test

80%

x(0B2DE5*KKKKLM(

80%

EAN 8

(6450*TRMN(

47

6

ÌtestwÎ

DATALOGIC JET™

0.38 mm (15 mils)

Code 39

Interleaved 2/5

Code 128

17162

0123456784

test

100%

Medium Density Codes

EAN 13

x(0B2DE5*KKKKLM(

EAN 8

100%

(6450*TRMN(

48

TEST CODES

Ìte

stwÎ

6

0.50 mm (20 mils)

Code 39

Interleaved 2/5

Code 128

17162

0123456784

test

120%

Low Density Codes

EAN 13

x(0B2DE5*KKKKLM(

EAN 8

120%

(6450*TRMN(

49

GLOSSARY

Access Point

A device that provides transparent access between Ethernet wired networks and
IEEE 802.11 interoperable radio-equipped mobile units. Hand-held terminals, PDAs
or other devices equipped with radio cards, communicate with wired networks using
Access Points (AP). The mobile unit (PDA), may roam among the APs in the same
subnet while maintaining a continuous, seamless connection to the wired network.

Barcode

A pattern of variable-width bars and spaces which represents numeric or
alphanumeric data in binary form. The general format of a barcode symbol consists
of a leading margin, start character, data or message character, check character (if
any), stop character, and trailing margin. Within this framework, each recognizable
symbology uses its own unique format.

Baud Rate

A measure for data transmission speed.

Bit

Binary digit. One bit is the basic unit of binary information. Generally, eight
consecutive bits compose one byte of data. The pattern of 0 and 1 values within the
byte determines its meaning.

Bits per Second (bps)

Number of bits transmitted or received per second.

Bluetooth®

A standard radio technology using a proprietary protocol. The onboard Bluetooth
module in the PDA is compatible with the 1.1 protocol.

Byte

On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a
pattern to represent a specific character or numeric value. Bits are numbered from
the right, 0 through 7, with bit 0 the low-order bit. One byte in memory can be used to
store one ASCII character.

Decode

To recognize a bar code symbology (e.g., Codabar, Code 128, Code 3 of 9,
UPC/EAN, etc.) and analyze the content of the bar code scanned.

50

EEPROM

Electrically Erasable Programmable Read-Only Memory. An on-board non-volatile
memory chip.

Flash Disk

Non-volatile memory for storing application and configuration files.

GSM

Global System for Mobile communication. It is a standard for digital cellular
communications, currently used in the 900 MHz and 1800 MHz bands.

GPRS

General Packet Radio Service. GPRS is a wireless packet-based communication
service based on GSM. Its data transfer is rated between 56 Kbps to 114 Kbps. It
makes very efficient use of available radio spectrum, and users pay only for the
volume of data sent and received.

Host

A computer that serves other terminals in a network, providing services such as
network control, database access, special programs, supervisory programs, or
programming languages.

Liquid Crystal Display (LCD)

A display that uses liquid crystal sealed between two glass plates. The crystals are
excited by precise electrical charges, causing them to reflect light outside according
to their bias. They use little electricity and react relatively quickly. They require
external light to reflect their information to the user.

Light Emitting Diode (LED)

A low power electronic light source commonly used as an indicator light. It uses less
power than an incandescent light bulb but more than a Liquid Crystal Display (LCD).

PDA

Personal Digital Assistant. PDA is a term for any small mobile hand-held device that
provides computing and information storage and retrieval capabilities for personal or
business use, often for keeping schedule calendars and address book information
handy.

RAM

Random Access Memory. Data in RAM can be accessed in random order, and
quickly written and read.

51

RF

Radio Frequency

RFID (Radio frequency identification)

A technology that incorporates the use of electromagnetic or electrostatic coupling in
the radio frequency (RF) portion of the electromagnetic spectrum to uniquely identify
an object, animal, or person. RFID is coming into increasing use in industry as an
alternative to the barcode identification.

RTC

Real Time Clock.

52

INDEX

A

Accessories; 3
Available Models; 1

B

Backup Directory File Management;

39

Bluetooth® Manager Device Setup;

35

Buttons; 31

C

Charging the Batteries; 40
Cleaning the PDA; 42
Connection Cables; 10

RS232 Direct Connection; 10
USB Direct Connection; 10

Connections; 4

RS232/USB Direct Connection; 4
WLAN Connection; 5
WPAN Connections; 6

WWAN Connections; 7
Control Panel; 30
Conventions; vii

D

Data Capture; 13

Imager Data Capture; 14

Laser Data Capture; 13

RFID Data Capture; 15
Data Capture Configuration; 25
Datalogic Jet™ PDA Description; 1
Default Settings; 28
Description of the Keys; 16

E

End User License Agreement; v

F

Files Admin; 32

G

General View; xv
Glossary; 50

K

Key Selection

Function Oriented Keyboard; 21
Standard Keyboard; 19

Key Selection; 19

M

Maintenance; 40
Microsoft® ActiveSync®; 37

P

Package Contents; 2
PDA Startup; 11

R

Reader Parameters; 27
Reading Diagrams; 46
Reference Documentation; vii
References; vii
Registry; 31
Replacing the Batteries; 41

S

Safe Setup; 32
Safety Regulations; viii

Laser Safety; ix

Radio Compliance; xiii
Save Session; 32
Scan Parameters; 27

53

Services and Support; vii
SIM Card; 8
Status Indicators; 23
System Control and Navigation Keys;

16
Function Oriented Keyboard; 17
Standard Keyboard; 16

T

Technical Features; 43

Communication; 43
Electrical; 43
Environmental; 43
Hardware; 43

Mechanical; 44

Optical; 44; 45

Programming; 44

RF Communication; 43
Test Codes; 47

U

Using the Stylus; 12

W

Wireless Communication; 34

54

DATALOGIC S.p.A.,

Via Candini, 2

40012 - Lippo di Calderara

dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el

Datalogic JET XXX-XXX

e tutti i suoi modelli

and all its models
et tous ses modèles
und seine modelle
y todos sus modelos

sono conformi alla Direttiva del Consiglio Europeo sottoelencata:
are in conformity with the requirements of the European Council Directive listed below:
sont conformes aux spécifications de la Directive de l'Union Européenne ci-dessous:
der nachstehenden angeführten Direktive des Europäischen Rats entsprechen:
cumple con los requisitos de la Directiva del Consejo Europeo, según la lista siguiente:

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:

ETSI EN 301 489-7, August 2002: Title: E

ETSI EN 301 489-17, September 2000: E

ETSI EN 301 511, March 2003: G

ETSI EN 300 330-2 June, 2001: E

Bologna - Italy

1999/5/EEC R&TTE

LECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS

(ERM); ELECTROMAGNETIC COMPATIBILTY (EMC) STANDARD FOR RADIO

EQUIPMENT AND SERVICES
PORTABLE RADIO AND ANCILLARY EQUIPMENT OF DIGITAL CELLULAR RADIO
TELECOMMUNICATIONS SYSTEMS

LECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM);

E

LECTROMAGNETIC COMPATIBILTY (EMC) STANDARD FOR RADIO EQUIPMENT

AND SERVICES
TRANSMISSION SYSTEMS AND

LOBAL SYSTEM FO R MOBILE COMMUNICATIONS (GSM); HARMONIZED EN

FOR MOBILE STATIONS IN THE GSM 900 AND GSM 1800 BANDS COVERING
ESSENTIAL REQUIREMENT UNDER ARTICLE

(1999/5/EC)

LECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM);
HORT RANGE DEVICES (SRD); RADIO EQUIPMENT IN THE FREQUENCIES

S

RANGE
RANGE BETWEEN

ARTICLE 3.2 OF THE R & TTE DIRECTIVE

; PART 17: SPECIFIC CONDITIONS FOR 2,4 GHZ W IDEBAND

9 KHZ TO 25 MHZ AND INDUCTIVE LOOP SYSTEMS IN THE FREQUENCY

; PART 7: SPECIFIC CONDITIONS FOR MOBILE AND

(GSM AND DCS)

5 GHZ HIGH PERFORMANCE RLAN EQUIPMENT

3.2 OF THE R&TTE DIRECTIVE

9 KHZ TO 30 MHZ; PART 2: HARMONIZED EN UNDER

04

ETSI EN 300 328-2, December 2001: E

EN 60950-1, December 2001: In

Lippo di Calderara, 20/12/2004
Ruggero Cacioppo
Quality Assurance Laboratory Manager

LECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM);

IDEBAND TRANSMISSION SYSTEMS; DATA TRANSMISSION EQUIPMENT

W

OPERATING IN THE
MODULATION TECHNIQUES
REQUIREMENTS UNDER

FORMATION TECHNOLOGY EQUIPMENT – SAFETY –

ART 1: GENERAL REQUIREMENTS

P

2,4 GHZ ISM BAND AND USING SPREAD SPECTRUM

; PART 2: HARMONIZED EN COVERING ESSENTIAL

ARTICLE 3.2 OF THE R & TTE DIRECTIVE