User´s Manual
WR series
Antes de utilizar el equipo, lea la sección
“Pre cau cio nes de seguri dad ” d e este
ma nu al . Co nse rv e es te m anu al p ar a
futuras consultas.
Before operating the device, please read
the “Safety precautions” section of this
manual. Retain this manual for future
reference.
CONTENTS
SAFETY PRECAUTIONS
WARRANTY
DECLARATION OF CONFORMITY
SYSTEM DESCRIPTION
LINE DRAWINGS
CONNECTION
SPECIFICATIONS
CONFIGURATIONS
4 x WR-8826 (625W @ 8 Ohms)
8 x WR-8826 (1150W @ 4 Ohms)
16 x WR-8826 (2100W @ 2 Ohms)
4 x WR-6412 or WR-6415 (1150W @ 4 Ohms)
8 x WR-6412 or WR-6415 (2100W @ 2 Ohms)
16 x WR-6412 or WR-6415 (3700W @ 2 Ohms)
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING
3
4
5
6
7
7-8
9
10-12
13-16
17
Manual del Usuario / WR series / User’s Manual
WR series
Cajas acústicas pasivas / Passive loudspeaker enclosures
Precauciones de Seguridad
Safety Precautions
Conserve y lea todas estas instrucciones.
Siga todas las advertencias.
El signo de exclamación dentro de un triángulo indica la
existencia de componentes internos cuyo reemplazo puede
afectar a la seguridad.
El doble cuadrado indica equipo de Clase II. The double square indicates Class II device.
Las especificaciones se encuentran en la etiqueta de la parte
posterior del producto.
El colgado del equipo sólo debe realizarse utilizando los herrajes
de colgado recomendados y por personal cualificado.
Equipo IP-56 según la norma IEC 60529: 1989 + M1 @ 1999
con un ángulo horizontal mínimo de -2º.
Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.
Equipo diseñado para funcionar entre -25ºC y 70ºC. La
humedad relativa máxima del 95% con 40ºC de temperatura
ambiente.
Keep these instructions.
Heed all warnings. Follow all instructions.
The exclamation point inside an equilateral triangle indicates the
existence of inter nal components whose substitution may affect
safety.
The specifications can be found on the rear label of the product.
The appliance should be flown only from the rigging points and
by qualified personnel.
IP-56 equipment (IEC 60529: 1989 + M1 @ 1999). Minimum
horizontal angle -2º.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of
electrical and electronic equipment.
Working temperature ranges from -25ºC to 70ºC. The maximum
relative humidity of 95% with ambient temperature 40ºC.
El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.
El equipo cuenta con dos conectores de entrada en paralelo
para facilitar la conexión de varias cajas en paralelo.
No emplace altavoces en proximidad a equipos sensibles a
campos magnéticos, tales como monitores de televisión o
material magnético de almacenamiento de datos.
No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el aparato se haya dañado de alguna
forma, tal como que haya caído líquido o algún objeto en el
interior del aparato, haya sido expuesto a lluvia o humedad, no
funcione correctamente o haya recibido un golpe.
Limpie con un paño seco. No use limpiadores con disolventes.
The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.
Note that the two input connectors are wired in parallel to
provide easy parallel connection of several enclosures.
Do not place loudspeakers in proximity to devices sensitive to
magnetic fields such as television monitors or data storage
magnetic material.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
Clean only with a dry cloth. Do not use any solvent based
cleaners.
Manual del Usuario / WR series / User’s Manual
3
GARANTÍA
Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.
Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.
Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.
Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.
Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.
WARRANTY
All D.A.S. products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.
4
Manual del Usuario / WR series / User’s Manual
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
D.A.S. Audio, S.A.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).
Declara que la serie WR:
Declares that WR series:
Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:
l Low Voltage Directive 2006/95/EC
l Regulation (EU) No 305/2011 - Constrution Products
(Certificate of Constancy of Performance: 0359-CPR-00429)
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
l EN 60065:2002 +A1:2006 + A11:2008 + A2:2010 + A12:2011
Audio, video and similar electronic apparatus. Safety requirements.
l EN 54-24:2008
Fire detection and fire alarm systems. Part 24: Components of voice
alarm systems. Loudspeakers.
Manual del Usuario / WR series / User’s Manual
5
SYSTEM DESCRIPTION
Introduction
The WR (Weather Resistant) series is a series
of products aimed at the outdoor installation
market.
This series is EN 54 certified according to the
EN 54-24:2008 standard ( Fire detection and fire
alarm systems. Part 24: Components of voice
alarm systems. Loudspeakers).
This series is composed of 3 base models:
– WR-8826 a dual 6” two-way
– WR-6412 a 12” two-way
– WR-6415 a 15” two-way
Each of these models will be offered in two
exposure ratings:
– CX “covered exposure” for applications where
cabinets are covered or protected.
– DX “direct exposure” where cabinets are
unprotected and directly exposed to the
environment.
The CX versions are protected with a thick
exterior Iso-Flex paint coating.
The DX versions augment the protection rating
by employing a supplementary fiberglass exterior
finish.
Models and versions;
WR-8826:
WR-8826CX, covered exposure, black
WR-8826DX, direct exposure, black
WR-8826CXW, covered exposure, white
WR-8826DXG, direct exposure, grey
WR-6412:
WR-6412CX, covered exposure, black
WR-6412DX, direct exposure, black
WR-6412CXW, covered exposure, white
WR-6412DXG, direct exposure, grey
Stainless steel fittings and mounting hardware
are offered for both versions.
The WR-8826 models are equipped with the
M-1 driver employing a 1” annular diaphragm and
an 80º x 80º horn geometry.
The WR-6412 and WR-6415 models use
D.A.S. loudspeakers equipped with robust 4”
voice coils and the M-75 compression driver with
1.5” exit and a 3” voice coil. These models with
60º x 40º horn geometry.
All the speaker components are treated for
weather resistance and extended durability in
extreme environments.
The WR series enclosures are manufactured
using exterior grade plywood. Black, white or
military grey color options are available in both
exposure ratings (IP56 according to IEC 60529
standards).
The perforated stainless steel protective grilles
are painted to match the cabinet finish and backed
with foam over a vapor barrier to avoid the entry of
water.
WR-6415:
WR-6415CX, covered exposure, black
WR-6415DX, direct exposure, black
WR-6415CXW, covered exposure, white
WR-6415DXG, direct exposure, grey
The barrier strip connector is protected by a
waterproof cover, and the connection wire
equipped with a cable gland.
6
LINE DRAWINGS
ALL DIMENSIONS IN MILIMETERS
226
WR-8826WR-6415 WR-6412
267
Bottom View
390
Bottom View Right ViewFront View
456
Bottom View
Front View
Front View Rear View
390
462
545
Right View
Right View
Rear View
700
Rear View
770
CONNECTION
The WR series includes protection methods to
ensure the best connectivity conditions even under
harsh weather conditions.
It includes a waterproof cover which gives us
a double connection chamber.
Don’t remove after
installation
After the installation is finished, don’t remove
any safety parts in normal working conditions.
Security operations and/or technical services
should be performed by authorised staff.
The system includes 5m of connection wire
ready to use in the application.
The color code is:
.- Blue --> +
.- Brown --> -
To obtain a better performance and achieve
the best optimization of the system parameters,
DAS AUDIO recommends using the WR cabinets
with amplifier models D-20 or D-100 and the
DS P 2 04 0 p r o c e ssor as sho w n i n t h e
configurations in this manual.
For assembling SPEAKON connectors, follow
the amplifier’s user manual for the correct
connection.
Manual del Usuario / WR series / User’s Manual
7
The system includes 5m of connection wire ready to use in the application. If more than 5m of connection wire
is required, a longer cable can be used. If so proceed as follows:
1.- Prepare the rear part of the enclosure for cable connection, removing the existing cable.
INPUT
INPUT
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
MODEL
IP RATING
RATED NOISE POWER
RATED IMPEDANCE
ENVIRONMENTAL TYPE
FOR USAGE AND DISPOSAL
D.A.S. Audio, s.a. (Valencia)
WR-XXXX
EN54-24: 2008
14
0359-CPR-00429
0359
REFER TO USER MANUAL
INFORMATION
CLASS II DEVICE
N1918
MADE IN SPAIN
IP56
W
8 ohms
B
2.- Screw the cables to the barrier strip following the label indications.
INPUT
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
INPUT
OUTPU T
OUTPU T
OUTPU T
OUTPU T
OUTPU T
3.- Fix the cover of the rear part of the enclosure with six screws.
Don’t remove after installation
8
Manual del Usuario / WR series / User’s Manual
TECHNICAL SPECIFICATIONS
Technical Specifications
RMS (Average) Power Handling :
Program Power Handling :
On-axis Frequency Range (-10dB):
Nominal Impedance :
On-axis Sensitivity, 1w/1m :
Enclosure Material:
Color/Finish:
Peak Power Handling :
Minimum Impedance :
Rated Peak SPL at full power:
Nominal -6dB Beamwidths:
Transducers/Replacement Parts:
Connector:
Dimensions (H x W x D):
Optional Accessories:
Grille:
Net Weight:
EN54-24 Based Technical Specifications
On-axis Frequency Range (-10dB):
Nominal Impedance:
On-axis Sensitivity 1w/4m :
Horizontal Coverage Angles (-6dB) :
Measured Maximum SPL at 4m :
Vertical Coverage Angles (-6dB) :
Enclosure Material:
Color/Finish:
Transducers/Replacement Parts:
Environmental Performance:
Connector:
Dimensions (H x W x D):
Nominal Power :
Minimum Impedance:
Environmental Type:
Grille:
Optional Accessories:
Net weight:
WR-6412
R
400 W
P
800 W
K
1600 W
60 Hz - 20 kHz
z
8 Ohms
z
8,2 Ohms @ 135 Hz
98 dB SPL
130 dB SPL
60º x 40º Rotatable
Birch Plywood
CX, Black or White/Polyurea
DX, Military Grey or Black/
Fiberglass
LF: 12AV/GM 12P
HF: M-75/GM M-75
Stainless steel
Barried Strip
70 x 39 x 39 cm
27,6 x 10,4 x 10,4 in
24 kg (52,8 lb)
AXU-WR6412
WR-6412
T
300 W
60 Hz - 20 kHz
8 Ohms
8,2 Ohms @ 135Hz
S
82,5 dB
M
106,7 dB
C
500Hz, 135º. 1kHz, 92º.
2kHz, 70º. 4kHz, 65º.
C
500Hz, 144º. 1kHz, 122º.
2kHz, 57º. 4kHz, 42º.
Birch Plywood
CX, Black or White/Polyurea
DX, Military Grey or Black/
Fiberglass
LF: 12AV/GM 12P
HF: M-75/GM M-75
Type B
EN 60529 IP 56
Stainless steel
Undeterminated cable
70 x 39 x 39 cm
27,6 x 10,4 x 10,4 in
24 kg (52,8 lb)
AXU-WR6412
WR-6415
400 W
800 W
1600 W
55 Hz - 20 kHz
8 Ohms
8 Ohms at 133 Hz
99 dB SPL
131 dB SPL
60º x 40º Rotatable
Birch Plywood
CX, Black or White/Polyurea
DX, Military Grey or Black/
Fiberglass
LF: 15AV/GM 15P
HF: M-75/GM M-75
Stainless steel
Barried Strip
77 x 46,2 x 45,5 cm
30,3 x 18,2 x 17,9 in
28 kg (61,6 lb)
AXU-WR6415
WR-6415
300 W
55 Hz - 20 kHz
8 Ohms
8 Ohms @ 133 Hz
82dB
107 dB
500Hz, 120º. 1kHz, 84º.
2kHz, 60º. 4kHz, 60º
500Hz, 127º. 1kHz, 105º.
2kHz, 54º. 4kHz, 40º
Birch Plywood
CX, Black or White/Polyurea
DX, Military Grey or Black/
Fiberglass
LF: 15AV/GM 15P
HF: M-75/GM M-75
Type B
EN 60529 IP 56
Stainless Steel
Barried Strip
77 x 46,2 x 45,5 cm
30,3 x 18,2 x 17,9 in
28 kg (61,6 lb)
AXU-WR6415
WR-8826
200 W
400 W
800 W
70 Hz - 22 kHz
16 Ohms
13.6 Ohms @ 200Hz
93 dB SPL
122 dB SPL
80º x 80º
Birch Plywood
CX, Black or White/Polyurea
DX, Military Grey or Black/
Fiberglass
LF: 2 x 6B/6B
HF: M-1/M-1
Stainless steel
Barried Strip
54,5 x 22,6 x 26,7 cm
21,5 x 8,9 x 10,5 in
10 kg (22 lb)
AXU-WR8826, AXW-1
WR-8826
200 W
70 Hz - 22 kHz
8 Ohms
6,7 Ohms @ 8320 Hz
75,3dB
97,05 dB
500Hz, 194º. 1kHz, 123º.
2kHz, 108º. 4kHz, 85º.
500Hz, 85º. 1kHz, 35º.
2kHz, 35º. 4kHz, 75º.
Birch Plywood
CX, Black or White/Polyurea
DX, Military Grey or Black/
Fiberglass
LF: 2 x 6B/6B
HF: M-1/M-1
Type B
EN 60529 IP 56
Stainless steel
Barried Strip
54,5 x 22,6 x 26,7 cm
21,5 x 8,9 x 10,5 in
10 kg (22 lb)
AXU-WR8826, AXW-1
T
Nominal Power based on a 100h test using a 6dB crest factor pink noise signal filtered according to the IEC 60268-1:1985 norm and band-pass filtered with Butterworth 24dB/Oct
filters from 89Hz to 11,2kHz.
S
Sensitivity and Max SPL measured using a 6dB crest factor pink noise, averaged from 100Hz to 10kHz in 1/3 Octave bands.
C
coverage measured from 500Hz to 4kHz in Octave bands.
R
Based on a 2 hour test using a 6dB crest factor pink noise signal.
P
Conventionally, 3dB higher than the RMS measure, although this already, utilizes a program signal.
K R
Corresponds to the signal crests for the test described in .
M
Obtain from a time window of a 30 seconds.
z
Impedance of a frequency range of 20 Hz - 2 kHz for better optimization of amplifiaction devices,
9
CONFIGURATIONS
4 x WR-8826
625W @ 8 Ohms
DSP-2040
D-20
Two WR-8826 (16ohms each) in parallel mode per channel.
Refer to the user manual of the D-20 amplifier for SPEAKON connection.
8 x WR-8826
1150W @ 4 Ohms
DSP-2040
D-20
Four WR-8826 (16ohms each) in parallel mode per channel.
Refer to the user manual of the D-20 amplifier for SPEAKON connection.
10
Manual del Usuario / WR series / User’s Manual
16 x WR-8826
2100W @ 2 Ohms
DSP-2040
D-20
Eight WR-8826 (16ohms each) in parallel per channel.
Refer to the user manual of the D-20 amplifier for SPEAKON connection.
4 x WR-6412 (or WR-6415)
1150W @ 4 Ohms
WR-6412 WR-6412
DSP-2040
D-20
Two WR-6412 (8 ohms each) in parallel per channel.
Refer to the user manual of the D-20 amplifier for SPEAKON connection.
Manual del Usuario / WR series / User’s Manual
11
8 x WR-6412 (or WR-6415)
2100W @ 2 Ohms
WR- 6415
WR- 6415
Four WR-6415 (8 ohms each) in parallel per channel.
Refer to the user manual of the D-20 amplifier for SPEAKON connection.
DSP-2040
D-20
WR-6412
16 x WR-6412 (or WR-6415)
3700W @ 2 Ohms
WR-6412
DSP-2040
D-100
WR-6412
12
WR-6412
Four WR-6412 (8 ohms each) in parallel per channel
Refer to the user manual of the D-100 amplifier for SPEAKON connection.
Manual del Usuario / WR series / User’s Manual
INSTALLATION INSTRUCTIONS
Warnings
This manual contains needed information for
flying D.A.S. Audio systems, description of the
elements and safety precautions. To perform any
operations related to flying the system, read the
present document first, and act on the warnings
and advice given. The goal is to the allow the user
to become familiar with the mechanical elements
required to fly the acoustic system, as well as the
safety measures to be taken during set-up and
teardown.
Absolutely no risks should be taken with
regards to public safety. When flying enclosures
from ceiling support structures, extreme care
should be taken to assure the load bearing
capabilities of the structures so that the installation
is absolutely safe. Do not fly enclosures from
unsafe structures. Consult a certified professional if
needed. All flying accessories that are not supplied
by D.A.S. Audio are the user's responsibility. Use
at your own risk.
Only experienced installers with adequate
knowledge of the equipment and local safety
regulations should fly speaker boxes. It is the
user's responsibility to ensure that the systems to
be flown (including flying accessories) comply with
state and local regulations.
The working load limits in this manual are the
results of tests by independent laboratories. It is
the user's responsibility to stay within safe limits. It
is the user's responsibility to follow and comply
with safety factors, resistance values, periodical
supervisions and warnings given in this manual.
Product improvement by means of research and
development is on going at D.A.S. Specifications
are subject to change without notice.
To this date, there is no international standard
regarding the flying of acoustic systems. However,
it is common practice to apply 5:1 safety factors
for enclosures and static elements. For slings and
elements exposed to material fatigue due to
friction and load variation the following ratios must
be met; 5:1 for steel cable slings, 4:1 for steel
chain slings and 7:1 polyester slings. Thus, an
element with a breaking load limit of 1000 kg may
be statically loaded with 200 kg (5:1 safety factor)
and dynamically loaded with 142 kg (7:1 safety
factor).
Periodicaly check the system replacing the
estructural elements which could be deteriorated.
Introduction
The WR system includes a double connection
chamber to achieve better connectivity conditions
even under harsh weather conditions.
The minimum angle in the horizontal plane to
ensure the max IP ratio IP56 is -2º.
When flying a system, the working load must
be lower than the resistance of each individual
flying point in the enclosure, as well as each box.
Hanging hardware should be regularly inspected
and suspect units replaced if in doubt. This is
important to avoid injury and absolutely no risks
should be taken in this respect. It is highly
recommended that you implement an inspection
and maintenance program on flying elements,
including reports to be filled out by the personnel
that will carry out the inspections. Local
regulations may exist that, in case of accident,
may require you to present evidence of inspection
reports and corrective actions after defects were
found.
Manual del Usuario / WR series / User’s Manual
13
Flying with eyebolts
The WR series models feature internal steel
flying points with mounting threads. These eyebolt
flying points are factory sealed with M10 screws,
which are replaced with eyebolts on the flying
points as required. Flying with eyebolts is very
ec o n o m i c al and s a fe, and i s specia l l y
recommended for fixed installations where the
boxes are permanently fixed.
The Allen-head screws must be removed and
replaced by M10 eyebolts on one side of the
enclosure. Each rigging point has a 200 kg (440 lb)
working load limit. Then choose the slings or
chains of required load resistance and length,
bearing in mind that the length difference between
the front and back slings or chains will determine
the vertical orientation. Alternatively, the back
bottom eyebolt point can be used to provide
vertical orientation.
The ANL-2 set is an optional set of four
eyebolts and four carabiners. (Dimensions below
are in millimetres).
In the case of the ANL-2 eyebolt, this means
that the 200 kg working load becomes 60 kg at 45
degrees. Do not use eyebolt flying if the load angle
is higher than 45 degrees.
% of working
load
0 Degrees
100% 65% 30% 25%
30 Degrees 45 Degrees More than 45
Degrees
ANL-2
Each ANL-2 eyebolt has a rated working load
of 200 kg. (440 lb). Each ANL-2 carabiner has a
working load of 330 kg (726 lb). If using other
hardware, make sure it is rated to handle the
required load.
When using eyebolts it is important to bear in
mind that the rated working load is only true for a
load applied in the plane of the eye, and is
significantly reduced for other angles. The drawing
illustrates the concept. The table shows the
variation of the working load as a function of the
load angle.
The following illustrations show different views
on eyebolt flying for a single box. The length of the
back cables or chains determines the vertical
angle of the box.
14
Manual del Usuario / WR series / User’s Manual
Rigging accessories
AXU-WR8826 / AXU-WR6412 / AXU-WR6415
The AXU-WR8826 /AXU-WR6412 /AXUWR6415 are not included with the WR-8826 /
WR-6412 and WR-6415 respectively in the
packaging.
The AXU accessories have been designed to
enable mounting the speakers in a horizontal and
vertical position.
They can also be installed on walls or ceilings.
Mounting instructions:
1.- Remove the top and bottom screws from
the speaker cabinet.
2.- Position the AXU-WRXXXX on the wall or
ceiling.
3.- Position the WR cabinet between the
arms of the support. Beware that the AXU
support allows for an asymmetric arc. Install in
the appropriate position.
4.- Attach the unit to the support using the
screws (step 1) but do not tighten.
5.- Aim the unit to the desired angle and
tighten screws.
Manual del Usuario / WR series / User’s Manual
15
Description of the AXU-WR8826 / AXU-WR6412 / AXU-WR6415
Refer to the user’s manual of accessories, on our website, for more information.
for mounting on wall or ceiling
free use
AXC-AT
for use in combination
with two AXC-AT
AXC-ZT
free use
16
90º
45º
0º
45º
Safety point
from 0º to 45º
Safety point
or from 45º to 90º
Manual del Usuario / WR series / User’s Manual
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
1 - No sound from any units.
2 NO sound from one unit.–
1.1 – No signal present in the
amplifier
1.2 – Defective cable.
1,3 – High number of speakers
connected in the same amplifier’s
channel.
2.1 – No signal present in the UNIT..
1.1.1 – Check that the amplifier is
on.
1.1.2 – Check that the gain is set
above its minimum setting.
1.1.3 – Check that there is a signal
to your amplifier from your mixer.
1.2.1 – Check that the cable from
the sound source to the UNIT is
connected correctly. Replace the
cable if defective.
1.2.2 – Check that none of the
connected cables are cut or frayed.
1,3,1 – Che ck the minim um
impedance requirements of your
amplifier.
2.1.1 – Check that the cable
between the UNITS is connected
correctly. Replace the cable if
defective.
2.1.2 – Check the balance control
on the mixer.
3 Poor stereo image or weak bass –
output
3.1 – Wrong connection
3.1.1 – Check the polarities (+/-) and
be sure that all the speakers are well
connected.
Manual del Usuario / WR series / User’s Manual
17
www.dasaudio.com
UM_WR_04_EN
D.A.S. AUDIO, S.A.
C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. 96 134 0525
Tel. Intl. +34 96 134 0860
Fax 96 134 0607
Fax Intl. +34 96 134 0607
D.A.S. AUDIO OF AMERICA, INC.
Sunset Palmetto Park
6816 NW 77th Court.
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1-888DAS4USA
Tel. +1 305 436 0521
Fax +1 305 436 0528
D.A.S. AUDIO ASIA PTE. LTD.
25 Kaki Bukit Crescent #01-00/02-00
Kaki Bukit Techpark 1
Singapore 416256
Tel. +65 6742 0151
Fax +65 6742 0157
Loading...