El signo de exclamación dentro de un triángulo indica la
existencia de importantes instrucciones de operación y
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.
ATENCIÓN: Es un producto clase A, por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1,
E2, E3 ó E4.
No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I. El producto debe ser
conectado a un enchufe con toma de tierra. Sólo use este
equipo con el cable de red de alimentación adecuado para su
país.
El signo del rayo con la punta de flecha, alerta contra la
presencia de voltajes peligrosos no aislados. Para reducir el
riesgo de choque eléctrico, no retire la cubierta.
No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.
No exponga este equipo a la lluvia o humedad sin el protector
de lluvia recomendado. No exponga el equipo a salpicaduras sin
el protector de lluvia recomendado, ni coloque sobre él objetos
que contengan líquidos, tales como vasos y botellas.
Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.
The exclamation point inside an equilateral triangle is intended to
alert the users to the presence of important operating and
mainten ance (servi cing) instruc tions in the li terature
accompanying the product. Heed all warnings. Follow all
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment
this product may cause radio interferences in which case the
user may be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments
according to EN55103-2.
Do not remove mains connector ground, it is dangerous and
illegal. Class I device. The product must be connected to a
mains socket outlet with protective earth connection. Only use
this equipment with an appropriate mains cord for your country.
The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
The circulation of air through the heatsink must not be blocked.
Do not expose this device to rain or moisture without the rain
protector supplied. Do not place any objects containing liquids,
such as bottles or glasses, on the top of the unit. Do not splash
liquids on the unit without the rain protector supplied.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.
Equipo diseñado para funcionar entre 15ºC y 45ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta trasera
(según IEC 60065). Si debe sustituir el fusible preste atención al
tipo y rango.
El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.
Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.
Para desconectar el dispositivo debe usar el enchufe.
Desconecte este aparato durante tormentas eléctricas,
terremotos o cuando no se vaya a emplear durante largos
periodos.
No emplace altavoces en proximidad a equipos sensibles a
campos magnéticos, tales como monitores de televisión o
material magnético de almacenamiento de datos.
El colgado del equipo sólo debe realizarse utilizando los herrajes
de colgado recomendados y por personal cualificado. No
cuelgue la caja de las asas y respete los valores máximos de
carga dados en el manual.
No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el equipo se haya dañado de alguna
forma, como que haya caído líquido o algún objeto en el interior
del aparato, haya sido expuesto a lluvia o humedad, no funcione
correctamente, haya recibido un golpe o su cable de red esté
dañado.
Limpie con un paño seco. No use limpiadores con disolventes.Clean only with a dry cloth. Do not use any solvent based
Working temperature ranges from 15ºC to 45ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the rear label (according to IEC 60065). If the fuse
needs to be replaced, please pay attention to correct type and
ratings.
The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.
If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.
To disconnect the device, you should use the mains plug. Unplug
this apparatus during lightning storms, earthquakes or when
unused for long periods of time.
Do not place loudspeakers in proximity to devices sensitive to
magnetic fields such as television monitors or data storage
magnetic material.
The appliance should be flown only from the rigging points and
by qualified personnel. Do not suspend the box from the handles
and respect the maximium load values given in the manual.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
cleaners.
Manual del Usuario / event series / User’s Manual
3
GARANTÍA
Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.
Las garantías sólo serán válidas si son por un defecto de fabricación
y en ningún caso por un uso incorrecto del producto.
La s re pa r ac ion es e n g a ra ntí a pu ed en s er r eal iz ada s,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.
Otros cargos como portes y seguros, son a cargo del comprador en
todos los casos.
Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una fotocopia
de la factura de compra.
WARRANTY
All our products are warrantied against any manufacturing defect for
a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory or
any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to the
nearest service center with a copy of the purchase invoice.
4
Manual del Usuario / event series / User’s Manual
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
DAS Audio Group, S.L.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).
Declara que la serie Event:
Declares that Event series:
Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:
l Directiva de Baja Tensión (Low Voltage Directive) 2014/35/UE
l Directiva de Compatibilidad Electromagnética (EMC) 2014/30/UE
l Directiva RoHS 2011/65/UE
l Directiva RAEE (WEEE) 2012/19/UE
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety
requirements.
l EN 55032:2012.- Electromagnetic compatibility of multimedia equipment.
Emission requirements.
l EN 55103-2:2009.- Electromagnetic compatibility. Product family standard
for audio, video, audio-visual and entertainment lighting control apparatus
for professional use. Part 2:Immunity.
l EN 50581:2012.- Technical documentation for the assessment of electrical
and electronic products with respect to the restriction of hazardous
substances.
Manual del Usuario / event series / User’s Manual
5
INTRODUCTI ON
For portable live sound applications, or fixed installations in almost any type of venue, the Event Line Arrays have
been designed to provide exceptional sound, steadfast reliability and value beyond comparison.
Also, the Event Line Arrays incorporate high frequency waveguides designed with the same technology as the
aero series. The Event series is expanded with two satellites: EVENT-212A and EVENT-212.120A, and a subwoofer:
EVENT-121A, to provide a complete solution for all your Events.
Features
– Powered 3-way line array system
– Clase D amplifier 3 x 1000 Wpeak
– DAScontrol™ Interface for fast setup
– High-end DSP chipsets with FIR filters
– 2 x 12″, 12MI4, loudspeakers in dual band configuration
– 1 x M-75 compression driver, 3" VCD
– 90º wide coverage
– Top grade Birch cabinet construction
– Robust quick-rig professional rigging hardware
EVENT-212A
EVENT-212A
The EVENT-212A is a powered, 3-way line array which employs two 12″ loudspeakers in a dual band
configuration where each speaker operates in a specific frequency range. At low frequencies, the speakers work in
tandem for maximum power, each driven by a dedicated amplifier channel providing 1000 Wpeak output power.
The loudspeaker units have been teamed up with a single M-75 compression driver and purpose-designed
injected aluminum high frequency waveguide to provide unmatched performance, sensitivity and coverage in the
formats offered.
The EVENT-212A line array incorporates the DAScontrol™ interface which offers a quick and hassle-free set-up
of the systems in arrays and easy alignment with the EVENT-218A and EVENT-121A subwoofer systems. Presets for
the number of units of the array, HF compensation for throw distances, and correction for the splay angle of the array
can be selected by way of DAScontrol™ and the LCD screen on the located on the back of the cabinet.
The powerful digital signal processing of the EVENT-212A includes Finite Impulse Response (FIR) filters
providing linear phase response and precise impulse response which in terms of performance, results in added clarity,
defined attack in percussion and overall, a more natural sound.
EVENT-212.120A
– Powered 3-way line array system
– Clase D amplifier 3 x 1000 Wpeak
– DAScontrol™ Interface for fast setup
– High-end DSP chipsets with FIR filters
– 2 x 12″, 12MI4, loudspeakers in dual band configuration
– 1 x M-75 compression driver, 3" VCD
– 120º wide coverage
– Top grade Birch cabinet construction
– Robust quick-rig professional rigging hardware
EVENT-212.120A
The EVENT-212.120A is a powered, 3-way line array which employs two 12″ loudspeakers in a dual band
configuration where each speaker operates in a specific frequency range. At low frequencies, the speakers work in
tandem for maximum power, each driven by a dedicated amplifier channel providing 1000 Wpeak output power.
The loudspeaker units have been teamed up with a single M-75 compression driver and purpose-designed
injected aluminum high frequency waveguide to provide unmatched performance, sensitivity and coverage in the
formats offered.
The EVENT-212.120A line array incorporates the DAScontrol™ interface which offers a quick and hassle-free
set-up of the systems in arrays and easy alignment with the EVENT-218A and EVENT-121A subwoofer systems.
Presets for the number of units of the array, HF compensation for throw distances, and correction for the splay angle of
the array can be selected by way of DAScontrol™ and the LCD screen on the located on the back of the cabinet.
The powerful digital signal processing of the EVENT-212.120A includes Finite Impulse Response (FIR) filters
providing linear phase response and precise impulse response which in terms of performance, results in added clarity,
defined attack in percussion and overall, a more natural sound.
6
Manual del Usuario / event series / User’s Manual
EVENT-121A
– Active direct radiating rear-loaded subwoofer system
– 1 x 21″, 21LFN, neodymium loudspeaker
– 3200Wpeak – 1600 Wcontinuous
– Class D amplifier and digital signal processing (DSP)
– Two balanced inputs with stereo filtered output
connections
– Variable low-pass filter 63 Hz-100 Hz
– Top located pole mount socket for TRD-6 optional pole
mount
– Rear located wheels to ease transport
– Top grade Birch cabinet construction
– Durable ISO-flex finish
EVENT-121A
The EVENT-121A is a direct radiating rear-loaded powered subwoofer system which incorporates a single 21″
neodymium loudspeaker providing “earth-moving” low-frequency reproduction for the Event Series line arrays. The
combination of direct radiation and rear-loading provides a high output, tight and accurate sub-bass response.
The EVENT-121A employs the new 21LFN loudspeaker which offers impressive features such as a 4″ sandwich
split winding voice coil, a powerful FEA optimized neodymium magnet assembly and a FEA optimized suspension
system with double silicon spider. The result is a loudspeaker with exceptional sensitivity, high power handling
capacity and a quality suspension design capable of withstanding the stress and mechanical fatigue of today´s highpower pro audio systems. An aluminum demodulating ring benefits lower distortion and effective forced ventilation of
the voice coil gap provides for a high thermal rating, and reduced power compression.
The EVENT-121A electronics package includes a 3200 Wpeak Class D amplifier and 24-bit high-end DSP for top
quality audio reproduction. On the rear panel, controls can be found for gain, polarity and a continually variable lowpass filter which ranges from 63 Hz to 100 Hz. A unique “cardioid preset” button simplifies the use of subs in cardioid
configurations, making setup of two to three units a snap without the need for an external DSP. The EVENT-121A is
phase response coherent with the EVENT-208A, EVENT-210A and EVENT-212A active tops offering precise
alignment. Two balanced inputs with stereo filtered outputs which can be switched to pass-through connections are
provided.
Manual del Usuario / event series / User’s Manual
7
POWER
CONFIGURATIONS
10x EVENT-212A + 2 x EVENT-212.120A + 6 x EVENT-218A
Use the same "number of units"
value in all enclosures
N.ofU: 6U
HPF: 80Hz
THROW: Mid
SPLAY: Narrw
1
O
POWER
EVENT-212.120
POWER
POWERPOWER
TOP L
POWERPOWER
TOP R
SUB RSUB L
EVENT-212.120
POWER
DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped
Speaker cabling
SC-1 1m XL R microphone signal balanced cable
PWCONLINK-09 0.9m powerC ON “jumper” NAC3FCB cable
Rigging frames
Dollies
PL-EV218S Plywood transport dolly for EVE NT-218A (max 4 u.)
PL-EV212S Steel transport dolly for EVE NT-212A/EVENT-212.120A (max 4 u.)
8
Manual del Usuario / event series / User’s Manual
UnitsProcessors
1
14
10
2AX-EV212 Rigging bumper for EVE NT-212A (max 16 u.)
2
3
CONFIGURATIONS (cont’d)
12x EVENT-212A + 4 x EVENT-212.120A + 8 x EVENT-218A
Use the same "number of units"
value in all enclosures
N.ofU: 8U
HPF: 80Hz
POWER
POWER
EVENT-212.120
EVENT-212.120
THROW: Mid
SPLAY: Narrw
1
TOP LTOP R
SUB RSUB L
POWER
O
EVENT-212.120
EVENT-212.120
POWERPOWERPOWER
Processors
DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped
Speaker cabling
SC-1 1m XL R microphone signal balanced cable
SC-2 2m XL R microphone signal balanced cable
PWCONLINK-09 0.9m powerC ON “jumper” NAC3FCB cable
Rigging frames
Dollies
PL-EV218S Plywood transport dolly for EVE NT-218A (max 4 u.)
PL-EV212S Steel transport dolly for EVE NT-212A/EVENT-212.120A (max 4 u.)
POWER
Manual del Usuario / event series / User’s Manual
Units
1
18
2
16
2AX-EV212 Rigging bumper for EVE NT-212A (max 16 u.)
4
4
9
CONFIGURATIONS (cont’d)
20 x EVENT-212A + 4 x EVENT-212.120A + 12 x EVENT-218A
Use the same "number of units"
value in all enclosures
N.ofU: 12U
POWER
POWER
POWER
EVENT-212.120
EVENT-212.120
HPF: 80Hz
THROW: Mid
SPLAY: Narrw
1
POWER
O
POWER
EVENT-212.120
EVENT-212.120
POWER
POWERPOWER
POWER
Processors
DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped
Speaker cabling
SC-1 1m XL R microphone signal balanced cable
SC-2 2m XL R microphone signal balanced cable
PWCONLINK-09 0.9m powerC ON “jumper“ NAC3FCB cable
Rigging frames
Dollies
PL-EV218S Plywood transport dolly for EVE NT-218A (max 4 u.)
PL-EV212S Steel transport dolly for EVE NT-212A/EVENT-212.120A (max 4 u.)
10
Manual del Usuario / event series / User’s Manual
POWERPOWER
POWER
Units
1
28
4
24
2AX-EV212 Rigging bumper for EVE NT-212A (max 16 u.)
6
6
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.