D.a.s. DASNET-RACK99-230-ETH User Manual

User's Manual

DASnet

DASNET-RACK99-230-ETH

Antes de utilizar el equipo, lea la sección
“Precauciones de seguridad” de este manual.
Conserve este manual para futuras consultas.

Before operating the device, please read the
“Safety precautions” section of this manual.
Retain this manual for future reference.

CONTENTS

SAFETY PRECAUTIONS

WARRANTY

DECLARATION OF CONFORMITY

INTRODUCTION

CONFIGURATIONS

ANNEX I : Schematics

ANNEX II : DASnet cables

3

4

5

6 - 8

9 - 10

11 - 12

13

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

DASNET-RACK99-230-ETH

Caja de distribución para DASnet / DASnet Splitter

Precauciones de Seguridad
Safety Precautions

El signo de exclamación dentro de un triángulo indica la
existencia de importantes instrucciones de operación y
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.

ATENCIÓN: Es un producto clase A, por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1,
E2, E3 ó E4.

No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I. El producto debe ser
conectado a un enchufe con toma de tierra. Sólo use este
equipo con el cable de red de alimentación adecuado para su
país.
El signo del rayo con la punta de flecha, alerta contra la
presencia de voltajes peligrosos no aislados. Para reducir el
riesgo de choque eléctrico, no retire la cubierta.

No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.

No exponga este equipo a la lluvia o humedad sin el protector
de lluvia recomendado. No exponga el equipo a salpicaduras sin
el protector de lluvia recomendado, ni coloque sobre él objetos
que contengan líquidos, tales como vasos y botellas.

Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.

The exclamation point inside an equilateral triangle is intended to
alert the users to the presence of important operating and
mainten ance (servi cing) instruc tions in the li terature
accompanying the product. Heed all warnings. Follow all
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment
this product may cause radio interferences in which case the
user may be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments
according to EN55103-2.
Do not remove mains connector ground, it is dangerous and
illegal. Class I device. The product must be connected to a
mains socket outlet with protective earth connection. Only use
this equipment with an appropriate mains cord for your country.

The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.

Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
The circulation of air through the heatsink must not be blocked.

Do not expose this device to rain or moisture without the rain
protector supplied. Do not place any objects containing liquids,
such as bottles or glasses, on the top of the unit. Do not splash
liquids on the unit without the rain protector supplied.

This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.

Equipo diseñado para funcionar entre 15ºC y 45ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta.

El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.

Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.

Para desconectar el dispositivo debe usar el enchufe.
Desconecte este aparato durante tormentas eléctricas,
terremotos o cuando no se vaya a emplear durante largos
periodos.

No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el equipo se haya dañado de alguna
forma, como que haya caído líquido o algún objeto en el interior
del aparato, haya sido expuesto a lluvia o humedad, no funcione
correctamente, haya recibido un golpe o su cable de red esté
dañado.

Limpie con un paño seco. No use limpiadores con disolventes. Clean only with a dry cloth. Do not use any solvent based

Working temperature ranges from 15ºC to 45ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the label.

The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.

If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.

To disconnect the device, you should use the mains plug. Unplug
this apparatus during lightning storms, earthquakes or when
unused for long periods of time.

No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.

cleaners.

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

3

GARANTÍA

Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.

Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.

Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.

Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.

Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.

WARRANTY

All our products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.

The warranty excludes damage from incorrect use of the product.

All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.

To claim a warranty repair, do not open or intend to repair the
product.

Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.

4

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

DECLARACIÓN DE CONFORMIDAD

DECLARATION OF CONFORMITY

DAS Audio Group, S.L.

C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).

Declara que DASNET-RACK99-230-ETH:
Declares that DASNET-RACK99-230-ETH:

Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:

l de Baja Tensión (Low Voltage Directive) 2014/35/UE

l de Compatibilidad Electromagnética (EMC) 2014/30/UE

l RoHS 2011/65/UE

l RAEE (WEEE) 2012/19/UE

Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:

l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety

requirements.

l EN 55032:2012.- Electromagnetic compatibility of multimedia equipment.

Emission requirements.

l EN 55103-2:2009.- Electromagnetic compatibility. Product family

standard for audio, video, audio-visual and entertainment lighting control
apparatus for professional use. Part 2:Immunity.

l EN 50581:2012.- Technical documentation for the assessment of

electrical and electronic products with respect to the restriction of
hazardous substances.

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

5

INTRODUCTION

The DASNET-RACK99-230-ETH, assembled in a 19", 8U high rack, is composed of three
elements: 1x DASNET-MATRIX99-ETH, 1x DASNET-PATCH-PW-9 and 1x DISTRO-RACKNET-32-9 (all
described in the following sections of this manual). Therefore it is a product derived from the
DASNET-RACK99-230, but with a different matrix. Knowing the needs required by the system in
terms of distribution of power, currents and supply voltages and electrical safety guidelines,
will be essential for a safe use of this rack.

Caution: Before connecting to the mains make sure that all electrical safety specifications
and guidelines are met, and that all the safety warnings have been given due attention.

8U high rack

AUDIO IN

PUSH

231

AUDIO / DASNET OUT

PUSH

PUSH

231

OUT

1

PUSH

231

231

OUT

2

OUT

3

PUSH

PUSH

231

231

OUT

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

1

OUT

2

OUT

3

DASNET-MATRIX99-ETH

DASNET-PATCH-PW-9

Matrix 9X9

230/115 V~

MAX.16A
per OUT

PUSH

PUSH

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

OUT

1

PH.1 PH.2 PH.3

PUSH

231

231

OUT

2

OUT

3

1U high panel

FI-Schalter

I

FI4030mA 4pol.

DISTRO-RACKNET-32-9

DISTRO-RACKNET-32-9

DASNET-RACK99-230-ETH

The DISTRO-RACKNET-32-9 allows the distribution of power between the different equipment
that form the system in a simple and safe way, and consists of:

L2

L1
PE

FI-Schalter

I

FI4030mA 4pol.

L3

C

L2

L1

N

PE

Frontal View Rear View

B

E

D

L3

N

A

A.- Three phase connector type IEC60309 or cetac, 32A / 400V for the input.

B.- Three phase connector type IEC60309 or cetac, 32A / 400V for the output (looped with the input).

C.- Phase 1, Phase 2 , Phase 3 breakers (one per ouput; total 9 units). The breakers are 16A nominal
current (In), type C (max Peak current > 5In).

D.- Phase LEDS. Indicate power per phase.

E.- Schuko outputs. There are 3 outputs per phase. There is one Auxiliary output connected in

parallel to the output 1 of phase 1 (max. 10W).

6

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

DASNET-PATCH-PW-9

The DASNET-PATCH-PW-9 provides AC power up to 9 connected devices, in a simple and
safe manner, using Neutrik connectors type PowerCon True1. The information on the AC
voltage range of the power supply and the maximum current available for each output is
shown on the silkscreen.

Voltage range and max. current per output

LED indicates Phase has power

Neutrik PowerCon True1 connector

230/115 V~

MAX.16A
per OU T

OUT

1

PH.1 PH.2 PH.3

OUT

OUT

2

3

OUT

1

OUT

OUT

2

3

OUT

1

OUT

OUT

2

3

Outputs connected to Phase 1: L1 Outputs connected to Phase 2: L2 Outputs connected to Phase 3: L3

On the rear of DASNET-PATCH-PW-9, a total of 9 cables with schuko are located. Each one of
the cables with its corresponding schuko must be connected to each output of the DISTRO-

RACKNET-32-9. On the other hand, the Schuko Auxiliary output of this will serve to power the
DASNET-MATRIX99-ETH.

DASNET-MATRIX99-ETH

The DASNET-MATRIX99-ETH distribution module routes 9 balanced audio channels and
DASnet monitoring data up to 9 “zones” or clusters with self-powered DAS Audio systems.

FRONT PANEL

PUSH

231

Matrix 9X9

Link switch for the inputs of the matrix

AUDIO IN:
Female XLR type connectors

PUSH

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

PUSH

231

AUDIO IN

PUSH

231

AUDIO / DASNET OUT

PUSH

231

PUSH

231

AUDIO / DASNET OUT:
Neutrik EtherCon connectors

Switch to active termination resistor

PUSH

231

PUSH

231

PUSH

231

TERMINATION

RESISTOR

1

POWER

POWER

ON

ON

LED ON

RS-485 OUT:

Male XLR type connector

ON

2

3

On the front panel of DASNET-MATRIX99-ETH we can view three connector types:
The first, AUDIO IN, female XLR type for 9 balanced audio inputs. The panel includes 8 link
switches for routing audio from inputs to outputs. By the use of the switches one unique audio
signal can be routed to all ethercon outputs (per example).

The second, AUDIO / DASNET OUT, Neutrik etherCon type to distribute audio and
monitoring data to the different groups of self powered cabinets, 9 DASnet output connectors.

Finally we have the output RS-485 connector, which allows us to join several matrix to form
a network with RS-485 protocol. Between the connectors the end-of-line switch is observed.

REAR PANEL

AC INPUT

100-230V~ 50/60Hz

10W

ETHERNET INPUT:

EtherCon type connector

ETHERNET

INPUT

Neutrik PowerCon True1 connector

2

2

2

1

1

3

1

3

3

2

1

3

AUDIO OUT:
Male XLR type connectors

AUDIO OUT

2

1

2

1

3

1

3

3

2

2

1

3

2

1

3

On the rear panel, using a power cable, the DASNET-MATRIX99-ETH will be connected to the
Schuko Auxiliary output of the DISTRO-RACKNET-32-9. This cable has a Neutrik connector type
PowerCon True1 at one end and an F type (CEE 7/7) plug at the other. In addition, we have 9
balanced audio outputs that are in parallel with the inputs.

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

7

Internally, each DASNET-MATRIX99-ETH has an RS-485 repeater that is directly connected
after the RS-485 input. The repeater allows having larger distances of cabling in the network
and a much higher number of devices without loosing capabilities.

The DASNET-MATRIX99-ETH is an ideal solution for audio and monitoring data distribution in
self powered cabinets that include DASnet: AERO-20A, AERO-40A, UX-221A, UX-30A, UX-218A,
UX-218A-R, LX-218CA-NET, ROAD-12A-NET, ROAD-15A-NET, etc.

There is a termination resistor which can be activated with a switch. It is recommendable to
engage it in the first and last matrix of the network to increase network stability.
With this system, ideal solution for touring, we can link a maximum number of 288 devices,
with a length of the DASnet data cable should higher than 1000 meters (counting both XLR
data cables and ecp_xx), through multiple DASNET-MATRIX99-ETH units and converting the data
transmission from ethernet to fiber optic. Note: always CAT5 cables for ethernet as a
minimum.

DASNET-MATRIX99-ETH needs a USB to RS-485 converter and a MOXA Nport 5150
converter, to convert data from RS-485 to ethernet. These converters can be provided by DAS
Audio. The converters have to be connected to the DASNET-MATRIX99-ETH using the
ETHERNET INPUT connector, on the rear panel.

USB-RS485

MOXA

DASnet

Net 1

Nport 5150

AUDIO OUT

2

2

2

2

2

2

2

AC INPUT

100-230V~ 50/60Hz

10W

ETHERNET

INPUT

2

1

1

1

1

1

1

1

3

3

3

3

3

3

1

3

3

2

1

3

Basic connection of DASNET-MATRIX99-ETH

On the front panel, the DASNET-MATRIX99-ETH offers flexible routing with switches that allow
you to mount an audio input to several outputs. The nine audio inputs can be linked directly to
their corresponding ethercon outputs. In addition, a single audio input can be linked to all
ethercon outputs by using the switches.
That is, if you look at the figure below, we have linked the inputs 1 with 2 on one side and 2
with 3 on the other. With this, it is enough to enter audio through connector 1 to output that
signal through all the connected output connectors: 1, 2 and 3, both ethercon on the front,
and XLR on the rear.
With this system, we can send a signal to all the equipment (linking all the outputs with the
input 1) or create several zones with different signal sends.

AUDIO IN

PUSH

231

AUDIO / DASNET OUT

PUSH

231

PUSH

231

PUSH

231

PUSH

231

PUSH

231

TERMINATION

RESISTOR

ON

2

1

POWER

POWER

ON

3

ON

Matrix 9X9

PUSH

231

PUSH

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

PUSH

231

Example of input links

8

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

CONFIGURATIONS

DASnet

Nport 5150

NET1: max 144 units

USB-RS485

MOXA

Nport 5150

MOXA

Nport 5150

EtherNet Switch

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

netLINK

ethernet

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

Fiber Optic Ethernet
Media Converter

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

cable>1km - max 288 units

optic fiber

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

Fiber Optic Ethernet
Media Converter

Nport 5150
NET2: max 144 units

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

2

2

1

1

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

2

2

1

1

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

2

2

1

1

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

AUDIO IN

2

2

1

3

1

3

1

3

2

1

1

3

3

AUDIO / DASNET OUT

AUDIO IN

2

2

2

1

1

3

3

AUDIO / DASNET OUT

AUDIO IN

2

2

2

1

1

3

3

AUDIO / DASNET OUT

2

2

2

1

1

3

3

2

1

1

3

3

2

1

1

3

3

2

1

1

AUDIO OUT

3

3

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

2

2

2

1

1

AUDIO OUT AUDIO OUT

3

3

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

2

2

2

1

1

AUDIO OUT AUDIO OUT

3

3

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

The best solution for large installations is to
convert DASnet, which uses the RS-485
protocol, to Ethernet. Doing so reduces cable
costs, as well as the speed of monitoring
software, regardless of the distance and
number of connected devices. To convert
DASnet (RS-485) to Ethernet, Nport 5150
converters are used. DASNET-MATRIX99-ETH is
the ideal solution to be used in this type of
applications.
Through multiple DASNET-MATRIX99-ETH
units, the network can be split into two
networks if necessary (with a maximum of 144
devices each). Each network will have different
"zones", each of which contains slave matrix
units connected to the MOXA Nport 5150
master that controls different clusters. From
each DASnet Matrix 99 ethernet, several
groups of self-powered devices can be
controlled. D AS audio recommends a
maximum number of 144 devices per subnet
(NET1 and NET2).
If the installation involves long distances, it
is strongly recommended to convert the
DASnet data from the Ethernet protocol to
optical fiber as shown (image opposite side).

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

netLINK

10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100

2

2

1

1

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

2

2

1

1

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

AUDIO IN

2

2

1

3

1

3

2

1

1

3

3

AUDIO / DASNET OUT

AUDIO IN

2

2

2

1

1

3

3

AUDIO / DASNET OUT

2

2

2

1

1

3

3

2

1

1

3

3

2

1

1

AUDIO OUT AUDIO OUT

3

3

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

2

2

2

1

1

AUDIO OUT AUDIO OUT

3

3

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

As we have indicated the DASNET-RACK99-230-ETH allows a power distribution of up to 32Amp per
phase (three-phase). Every 3 outputs of the DISTRO-RACKNET-32-9 of power are connected to a single
phase. This means that of each group of 3 PowerCon True 1 connectors, the maximum available
current is 32A.
The user must always consider the power consumption of the equipment (specified at 1/3 of the
nominal power with pink noise) connected to each output and DO NOT exceed the limit of 32A for
each group of 3 PowerCon outputs.

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

9

With the system configurations, DAS Audio recommends the maximum number of

cabinets that can be connected depending on the model, the power consumption
and the total equipment used (see table below).

Consumption
per unit

AERO-20A

AERO-40A

UX-218A

UX-221A

UX-30A

LX-118A

LX-218CA-NET

ROAD-12A-NET

ROAD-15A-NET

Mains

230V

1,8A

3A 6A

4,5A 9A

9A 18A

6,7A 13,4A

3A 6A

3,1A

(1)

1,7A

(2)

1,7A

115V

3,6A

6,2A

3,4A

3,4A

Note: C o n s u m p t i o n me a s u red a t 1/3 o f n o m i n a l p o w e r w i t h pi n k n o i s e .

( 1 ) Mode l s : ROAD-12ART-NET230, ROAD-12ALT-NET230, ROAD-12ART-NET115, ROAD-12ALT-NET115
(2) Models: ROAD-15ART-NET230, ROAD-15ALT-NET230, ROAD-15ART-NET115, ROAD-15ALT-NET115

MODEL: DASNET-RACK99-230-ETH

DAS Audio Group, S.L. (Valencia) MADE IN SPAIN

Rated Voltage:

Rated Current: 32A
IP rating: IP20

S/N

3/N/PE
400/230 V

50Hz/60Hz

www.dasaudio.com

10

Label of DASNET-RACK99-230-ETH

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

ANNEX I : Schematics

_

_ _

_

_

_

L1 L3L2

N L2L1 L3 N L2L1 L3

_

_

_

RCD

40A/30mA

____

_ _ _

_ _

_

_ _

_ _ _

_ _ _

OUT (Looped)IN

PC 230V 16A

___

_

_

PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16APC 230V 16A

_

_

_

_

_

_

_

_

_

_

PH3.1 PH3.2 PH3.3PH2.3PH2.2PH2.1PH1.3PH1.2PH1.1AUX

DISTRO-RACKNET-32-9

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

_

_

_

_

_

11

1.0

12

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

ANNEX II : DASnet cables

It is very important to use the system with the intended cables to prevent electromagnetic
interferences between the analog audio signal, the DASnet data and the power. Be sure to
check the specifications provided by the cable manufacturer. It is also especially important
when installing connectors yourself, to note that when termination is not accurate, a cable
will be unable to achieve its maximum performance and could have interferences.

There are 4 different types of cables.

- The main feeds which include power and a STP, CAT7 cable. These cables are named
eCP_xx (xx refers to cable length).

- The links between cabinets (aero40A/Convert15A/LX-218CAnet), which are STP CAT7
cables. Cable code eC_09

- Power Links between cabinets.Cable code Plink1_09

- Links for RoadNet series. Power+STP CAT7. eCPk_1/eCPk_5

Important

The main feed cable eCP_xx has the following structure:

Jacket

STP CAT 7 cable with Aluminium
Shield for each individual pair

AL Shield

and a main aluminium Shield.
The main Shield has to be
soldered to the etherCon
housing.

The eC_09 cable is a CAT5e
cable with global Aluminium
Shield.

ecP_xx: Power cable 3x2.5mm + CAT7 4x (2 x 0.14mm )

The pin out of the EtherCon to XLR is the following on the eCP cables:

etherCon XLR

1 Orange-White Audio+ 2
2 Orange Audio- 3
3 Green-White Audio Earth 1
4 Blue
5 Blue-White
6 Green Data Earth 1
7 Brown-White Data- (A) 3
8 Brown Data+ (B) 2

Jacket

2 2

Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual

13

www.dasaudio.com

UM_RACK992_01_EN

DAS Audio Group, S.L.

C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. [phone]

DAS Audio of America, INC.

6900 NW 52th Street
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1 888 DAS 4 USA

DAS Audio Asia PTE. LTD.

3 Temasek Avenue, Centennial
Tower #34-36
Singapore 039190
Tel. [phone]

DAS do Brasil LTDA.

Rua Dos Andradas, 382 SL
Santa Efigênia, São Paulo
Brasil. CEP: 01208-000
Tel. [phone]