D.a.s. DASNET-RACK99-230 User Manual

User's Manual

DASnet

DASNET-RACK99-230

Antes de utilizar el equipo, lea la sección
“Precauciones de seguridad” de este manual.
Conserve este manual para futuras consultas.

Before operating the device, please read the
“Safety precautions” section of this manual.
Retain this manual for future reference.

CONTENTS

SAFETY PRECAUTIONS

WARRANTY

DECLARATION OF CONFORMITY

INTRODUCTION

CONFIGURATIONS

12 x AERO-40A + 8 UX-218A

12 x AERO-40A + 6 UX-221A

ANNEX I : Schematics

ANNEX II : DASnet cables

3

4

5

6 - 8

9 - 14

15 - 16

17

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

DASNET-RACK 99-230

Caja de distribución para DASnet / DASnet Splitter

Precauciones de Seguridad
Safety Precautions

El signo de exclamación dentro de un triángulo indica la
existencia de importantes instrucciones de operación y
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.

ATENCIÓN: Es un producto clase A, por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1,
E2, E3 ó E4.

No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I. El producto debe ser
conectado a un enchufe con toma de tierra. Sólo use este
equipo con el cable de red de alimentación adecuado para su
país.
El signo del rayo con la punta de flecha, alerta contra la
presencia de voltajes peligrosos no aislados. Para reducir el
riesgo de choque eléctrico, no retire la cubierta.

No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.

No exponga este equipo a la lluvia o humedad sin el protector
de lluvia recomendado. No exponga el equipo a salpicaduras sin
el protector de lluvia recomendado, ni coloque sobre él objetos
que contengan líquidos, tales como vasos y botellas.

Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.

The exclamation point inside an equilateral triangle is intended to
alert the users to the presence of important operating and
mainten ance (servi cing) instruc tions in the li terature
accompanying the product. Heed all warnings. Follow all
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment
this product may cause radio interferences in which case the
user may be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments
according to EN55103-2.
Do not remove mains connector ground, it is dangerous and
illegal. Class I device. The product must be connected to a
mains socket outlet with protective earth connection. Only use
this equipment with an appropriate mains cord for your country.

The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.

Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
The circulation of air through the heatsink must not be blocked.

Do not expose this device to rain or moisture without the rain
protector supplied. Do not place any objects containing liquids,
such as bottles or glasses, on the top of the unit. Do not splash
liquids on the unit without the rain protector supplied.

This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.

Equipo diseñado para funcionar entre 15ºC y 45ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta.

El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.

Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.

Para desconectar el dispositivo debe usar el enchufe.
Desconecte este aparato durante tormentas eléctricas,
terremotos o cuando no se vaya a emplear durante largos
periodos.

No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el equipo se haya dañado de alguna
forma, como que haya caído líquido o algún objeto en el interior
del aparato, haya sido expuesto a lluvia o humedad, no funcione
correctamente, haya recibido un golpe o su cable de red esté
dañado.

Limpie con un paño seco. No use limpiadores con disolventes. Clean only with a dry cloth. Do not use any solvent based

Working temperature ranges from 15ºC to 45ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the label.

The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.

If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.

To disconnect the device, you should use the mains plug. Unplug
this apparatus during lightning storms, earthquakes or when
unused for long periods of time.

No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.

cleaners.

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

3

GARANTÍA

Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.

Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.

Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.

Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.

Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.

WARRANTY

All our products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.

The warranty excludes damage from incorrect use of the product.

All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.

To claim a warranty repair, do not open or intend to repair the
product.

Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.

4

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

DECLARACIÓN DE CONFORMIDAD

DECLARATION OF CONFORMITY

DAS Audio Group, S.L.

C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).

Declara que DASNET-RACK99-230:
Declares that DASNET-RACK99-230:

Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:

l de Baja Tensión (Low Voltage Directive) 2014/35/UE

l de Compatibilidad Electromagnética (EMC) 2014/30/UE

l RoHS 2011/65/UE

l RAEE (WEEE) 2012/19/UE

Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:

l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety

requirements.

l EN 55032:2012.- Electromagnetic compatibility of multimedia equipment.

Emission requirements.

l EN 55103-2:2009.- Electromagnetic compatibility. Product family

standard for audio, video, audio-visual and entertainment lighting control
apparatus for professional use. Part 2:Immunity.

l EN 50581:2012.- Technical documentation for the assessment of

electrical and electronic products with respect to the restriction of
hazardous substances.

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

5

INTRODUCTION

The DASNET-RACK99-230, assembled in a 19", 8U high rack, is composed of three elements:
1x DASNET-MATRIX99, 1x DASNET-PATCH-PW-9 and 1x DISTRO-RACKNET-32-9 (all described in the
following sections of this manual). Knowing the needs required by the system in terms of
distribution of power, currents and supply voltages and electrical safety guidelines, will be
essential for a safe use of this rack.

Caution: Before connecting to the mains make sure that all electrical safety specifications
and guidelines are met, and that all the safety warnings have been given due attention.

PUSH

PUSH

PUSH

231

231

OUT

2

OUT

3

Matrix 9X9

230/115 V~

MAX.16A
per OUT

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

OUT

1

PH.1 PH.2 PH.3

DISTRO-RACKNET-32-9

FI-Schalter

I

FI4030mA 4pol.

AUDIO IN

PUSH

231

AUDIO / DASNET OUT

8U high rack

DASNET-MATRIX99

DASNET-PATCH-PW-9

TERMINATION

POWER

ON

OUT

RESISTOR

OUT

PUSH

231

ON

2

1

3

2

3

PUSH

PUSH

231

OUT

1

PUSH

231

231

OUT

2

OUT

3

PUSH

PUSH

231

231

OUT

1

1U high panel

DISTRO-RACKNET-32-9

DASNET-RACK99-230

The DISTRO-RACKNET-32-9 allows the distribution of power between the different equipment
that form the system in a simple and safe way, and consists of:

L2

L1
PE

FI-Schalter

I

FI4030mA 4pol.

L3

C

L2

L1

N

PE

Frontal View Rear View

B

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

E

D

L3

N

A

A.- Three phase connector type IEC60309 or cetac, 32A / 400V for the input.

B.- Three phase connector type IEC60309 or cetac, 32A / 400V for the output (looped with the input).

C.- Phase 1, Phase 2 , Phase 3 breakers (one per ouput; total 9 units). The breakers are 16A nominal
current (In), type C (max Peak current > 5In).

D.- Phase LEDS. Indicate power per phase.

E.- Schuko outputs. There are 3 outputs per phase. There is one Auxiliary output connected in

parallel to the output 1 of phase 1 (max. 10W).

6

DASNET-PATCH-PW-9

The DASNET-PATCH-PW-9 provides AC power up to 9 connected devices, in a simple and
safe manner, using Neutrik connectors type PowerCon True1. The information on the AC
voltage range of the power supply and the maximum current available for each output is
shown on the silkscreen.

Voltage range and max. current per output

LED indicates Phase has power

Neutrik PowerCon True1 connector

230/115 V~

MAX.16A
per OU T

OUT

1

PH.1 PH.2 PH.3

OUT

OUT

2

3

OUT

1

OUT

OUT

2

3

OUT

1

OUT

OUT

2

3

Outputs connected to Phase 1: L1 Outputs connected to Phase 2: L2 Outputs connected to Phase 3: L3

On the rear of DASNET-PATCH-PW-9, a total of 9 cables with schuko are located. Each one of
the cables with its corresponding schuko must be connected to each output of the DISTRO-

RACKNET-32-9. On the other hand, the Schuko Auxiliary output of this will serve to power the
DASNET-MATRIX99.

DASNET-MATRIX99

The DASNET-MATRIX99 distribution module routes 9 balanced audio channels and DASnet
monitoring data up to 9 “zones” or clusters with self-powered DAS Audio systems.

Switch to active termination resistor

RS-485 IN:

PUSH

231

TERMINATION

RESISTOR

POWER

POWER

ON

ON

PUSH

231

ON

2

1

3

FRONT PANEL

PUSH

231

Matrix 9X9

AUDIO IN:
Female XLR type connectors

PUSH

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

PUSH

231

AUDIO IN

PUSH

231

AUDIO / DASNET OUT

PUSH

231

PUSH

231

Female XLR type connector

PUSH

231

PUSH

231

Link switch for the inputs of the matrix

AUDIO / DASNET OUT:
Neutrik EtherCon connectors

LED ON

RS-485 OUT:

Male XLR type connector

On the front panel of DASNET-MATRIX99 we can view three connector types:
The first, AUDIO IN, female XLR type for 9 balanced audio inputs. The panel includes 8 link
switches for routing audio from inputs to outputs. By the use of the switches one unique audio
signal can be routed to all ethercon outputs (per example).

The second, AUDIO / DASNET OUT, Neutrik etherCon type to distribute audio and
monitoring data to the different groups of self powered cabinets, 9 DASnet output connectors.

Finally we have the RS-485 connectors, which allow us to join several matrix to form a
network with RS-485 protocol. Between the connectors the end-of-line switch is observed.

REAR PANEL

AC INPUT

100-230V~ 50/60Hz

10W

Neutrik PowerCon True1 connector

2

2

2

1

1

3

1

3

3

2

1

3

AUDIO OUT:
Male XLR type connectors

AUDIO OUT

2

1

2

1

3

1

3

3

2

2

1

3

2

1

3

On the rear panel, using a power cable, the DASNET-MATRIX99 will be connected to the Schuko
Auxiliary output of the DISTRO-RACKNET-32-9. This cable has a Neutrik connector type PowerCon
True1 at one end and an F type (CEE 7/7) plug at the other. In addition, we have 9 balanced audio
outputs that are in parallel with the inputs.

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

7

Internally, each DASNET-MATRIX99 has an RS-485 repeater that is directly connected after
the RS-485 input. The repeater allows having larger distances of cabling in the network and a
much higher number of devices without loosing capabilities.

The DASNET-MATRIX99 is an ideal solution for audio and monitoring data distribution in self
powered cabinets that include DASnet: AERO-20A, AERO-40A, UX-221A, UX-30A, UX-218A, UX-
218A-R, LX-218CA-NET, ROAD-12A-NET, ROAD-15A-NET, etc.

There is a termination resistor which can
be activated with a sw itc h. It is
recommendable to engage it in the first and
last matrix of the network to increase
network stability.
With this system, ideal solution for
touring, we can link a maximum number of
144 devices, with a maximum total length
of the DASnet data cable should not
exceed 1000 meters (counting both XLR
data cables and ecp_xx CAT 7 cables).

Example of typical
touring network
with standard RS-485

DASnet

USB-RS485

The RS-485 protocol needs a USB to
RS-485 converter. This converter is
provided by DAS Audio with every system
pruchased. The USB to RS-485 converter
has to be connected to the DASNET-
MATRIX99 using the IN RS-485 connector.

zone 1

Matrix 9X9

“Terminator resistor” activated

PUSH

PUSH

231

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

AUDIO IN

PUSH

PUSH

231

PUSH

231

AUDIO / DASNET OUT

231

zone 2

PUSH

PUSH

231

231

LINK 1&2 LI NK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

AUDIO IN

PUSH

PUSH

231

PUSH

231

AUDIO / DASNET O UT

231

“Terminator resistor” activated

PUSH

PUSH

231

231

LINK 1&2 LI NK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

AUDIO IN

PUSH

PUSH

231

PUSH

231

AUDIO / DASNET O UT

231

PUSH

PUSH

231

PUSH

231

PUSH

231

PUSH

231

231

PUSH

PUSH

231

231

PUSH

PUSH

231

231

PUSH

PUSH

231

231

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

PUSH

PUSH

231

231

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

PUSH

PUSH

231

231

TERMINATION

RESISTOR

ON

2

1

POWER

ON

3

On the other hand, the DASNET-MATRIX99 offers flexible routing with switches on the front
panel that allow you to mount an audio input to several outputs. The nine audio inputs can be
linked directly to their corresponding ethercon outputs. In addition, a single audio input can be
linked to all ethercon outputs by using the switches.
That is, if you look at the figure below, we have linked the inputs 1 with 2 on one side and 2
with 3 on the other. With this, it is enough to enter audio through connector 1 to output that
signal through all the connected output connectors: 1, 2 and 3, both ethercon on the front,
and XLR on the rear.
With this system, we can send a signal to all the equipment (linking all the outputs with the
input 1) or create several zones with different signal sends.

Matrix 9X9

PUSH

231

PUSH

231

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

PUSH

231

AUDIO IN

PUSH

231

PUSH

231

PUSH

231

PUSH

231

AUDIO / DASNET OUT

PUSH

231

PUSH

231

TERMINATION

RESISTOR

POWER

POWER

ON

ON

PUSH

231

ON

2

1

3

Example of input links

8

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

CONFIGURATIONS

Example 1 : 12 x AERO-40A + 8 x UX-218A

2 x eCPK_20

2 x eCPK_20

L R

AUDIO IN

2

2

2

2

1

1

1

1

3

3

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

AUDIO / DASNET OUT

OUT2OUT

1

MAX.
20A/ OUT

OUT

3

PH.1 PH.2 PH.3

FI-Schalter

I

FI4030mA4pol.

2 x eCPK_20 2 x eCPK_20

DASN ET-RAC K99-230

2

2

1

1

1

3

3

3

OUT1OUT

OUT2OUT

1

2

OUT3OUT

3

PUSH

231

2

2

2

1

1

3

3

ON

2

1

POWER
ON

3

2 x eCPk_1

2 x eCPk_1

This is the recommended power distribution of the example configuration:

FROM 3 x AE RO-40A L

FROM 3 x AE RO-40A L

FROM 2 x U X-218A L

FROM 2 x U X-218A L

2

1

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

Matrix 9X9

OUT2OUT

1

MAX.

20A/ OUT

PH.1 PH.2 PH.3

AUDIO IN

2

2

2

1

1

1

1

3

3

3

3

AUDIO / DASNET OUT

OUT

1

OUT

3

FI-Schalter

I

FI4030mA4pol.

PUSH

2

2

1

1

3

3

OUT

2

OUT

3

231

2

2

2

1

1

3

3

ON

2

1

POWER

ON

3

OUT

OUT

1

2

OUT

3

FROM 3 x AE RO-40A R

FROM 3 x AE RO-40A R

FROM 2 x U X-218A R

FROM 2 x U X-218A R

Load per Phase:

Phase 1 = 3 x 3A + 3 x 3A + 3 x 3A = 27A

Phase 2 = 3 x 3A + 2 x 4,5A + 2 x 4,5A = 27A

Phase 3 = 2 x 4,5A + 2 x 4,5A = 18A

As we have indicated the DASNET-RACK99-230 allows a power distribution of up to 32Amp
per phase (three-phase). Every 3 outputs of the DISTRO-RACKNET-32-9 of power are connected
to a single phase. This means that of each group of 3 PowerCon True 1 connectors, the
maximum available current is 32A.
The user must always consider the power consumption of the equipment (specified at 1/3
of the nominal power with pink noise) connected to each output and DO NOT exceed the limit
of 32A for each group of 3 PowerCon outputs.

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

9

With the system configurations, DAS Audio recommends the maximum number of

cabinets that can be connected depending on the model, the power consumption
and the total equipment used (see table below).

Consumption
per unit

AERO-20A

AERO-40A

UX-218A

UX-221A

UX-30A

LX-118A

LX-218CA-NET

ROAD-12A-NET

ROAD-15A-NET

Mains

230V

1,8A

3A 6A

4,5A 9A

9A 18A

6,7A 13,4A

3A 6A

3,1A

(1)

1,7A

(2)

1,7A

115V

3,6A

6,2A

3,4A

3,4A

Note: C o n s u m p t i o n me a s u red a t 1/3 o f n o m i n a l p o w e r w i t h pi n k n o i s e .

( 1 ) Mode l s : ROAD-12ART-NET230, ROAD-12ALT-NET230, ROAD-12ART-NET115, ROAD-12ALT-NET115
(2) Models: ROAD-15ART-NET230, ROAD-15ALT-NET230, ROAD-15ART-NET115, ROAD-15ALT-NET115

MODEL: DASNET-RACK99-230

DAS Audio Group, S.L. (Valencia) MADE IN SPAIN

Rated Voltage:

Rated Current: 32A
IP rating: IP20

S/N

3/N/PE
400/230 V

50Hz/60Hz

www.dasaudio.com

10

Label of DASNET-RACK99-230

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

USB-RS485 Converter

x 1

243cm / 96”

228cm / 90”

4 x aero40

4 x aero40 4 x aero40

4 x aero40

4 x aero40

251cm / 99”

4 x aero40

Dollies

x 3

PL-40S metal transport dolly for 3 or 4 AERO-40A

x 1

4 x aero40 4 x aero40

UX-218A

UX-218A

DSP-4080

Euro truck Euro truck

Processors (included in the racks)

12 AERO-40A + 8 UX-218A 12 AERO-40A

243cm / 96”

4 x aero40 4 x aero40

4 x aero40 4 x aero40

UX-218A

UX-218A

228cm / 90”

UX-218A

UX-218A

4 x aero40

UX-218A

4 x aero40

4 x aero40

UX-218A

American Truck 90” x 232” American Truck 90” x 232”

UX-218A

UX-218A

UX-218A

4 x aero40 4 x aero40

UX-218A

4 x aero40

American Truck 99” x 232” American Truck 99” x 232”

251cm / 99”

x 4

x 8

A40 Accessories

Speaker cabling

eCPK_20 (CAT 7 ethernet cable + 3x2.5mm2, audio +data + power, 20m length)

x 8

x 8

eC_09 (CAT 7 ethernet cable; audio +data, 90cm length)

x 4

1

3

PUSH

2

RESISTOR

TERMINATION

2

3

1

2

3

1

2

3

1

2

3

1

2

3

1

AUDIO IN

2

3

1

2

3

1

2

3

1

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

2

3

1

Plink1_09 (power link 2.5mm2 90cm)

DASNET-RACK99

eCPk_1 (ethernet cable)

ON

2

3

1

ON

POWER

AUDIO / DASNET OUT

Matrix 9X9

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

x 3

x 4

x 1

3

2

OUT

OUT

1

OUT

3

2

OUT

OUT

1

OUT

FI4030mA4pol.

FI-Schalter

3

2

OUT

OUT

1

PH.1 PH.2 PH.3

OUT

MAX.

16A/ OUT

I

Covers

FUN-4-AE40 is a protective nylon cover for 4 AERO-40A

Rigging frames

FUN-2-UX218 nylon cover for a stack of 2 UX-218A

x 2

AX-AE40S3

Dollies

PL-UX218S

The PL-UX218S dolly is used to

transport stacks of 2 or 3 UX-218A.

11

LINK LINK LINK LI NK

LINKLINKLINKLINK

Example 2 : 12 x AERO-40A + 6 x UX-221A

2 x eCPK_20

2 x eCPK_20

USB-RS485 converter

L R

EDIT

DSP-4080

ON

2

1

3

3

PUSH

2

1

3

2

OUT

RESISTOR

OUT

ON

POWER

TERMINATION

2

3

1

1

OUT

2

3

1

2

3

1

3

2

2

OUT

OUT

3

1

2

3

1

1

OUT

AUDIO IN

AUDIO / DASNET OUT

2

3

1

2

3

1

2

3

1

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

2

3

1

Matrix 9X9

ON

2

1

3

3

PUSH

2

1

RESISTOR

ON

POWER

TERMINATION

2

3

1

2

3

1

2

3

1

2

3

1

2

3

1

AUDIO IN

AUDIO / DASNET OUT

2

3

1

2

3

1

2

3

1

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

2

3

1

Matrix 9X9

FI4030mA4pol.

FI-Schalter

I

3

2

OUT

OUT

1

PH.1 PH.2 PH.3

OUT

MAX.

16A/ OUT

3

2

OUT

OUT

1

OUT

3

2

OUT

OUT

1

OUT

3

2

OUT

OUT

1

PH.1 PH.2 PH.3

OUT

MAX.

16A/ OUT

DASNET-RACK-99

FI4030mA4pol.

FI-Schalter

I

DASNET-RACK-99

3 x eCPK_20

3 x eCPK_20

LINK LINK LINK LINK

LINKLINKLINKLINK

12

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

PHASE 1: 18A

PHASE 2: 18A

PHASE 3: 9A

LOAD PER PHASE

FROM 1 x UX-221A R

FROM 1 x UX-221A R

FROM 1 x UX-221A R

ON

2

1

3

3

PUSH

2

1

3

2

OUT

OUT

RESISTOR

ON

POWER

TERMINATION

2

3

1

2

1

2

1

2

1

2

1

AUDIO IN

2

1

2

1

2

1

2

1

1

OUT

3

3

3

2

OUT

OUT

3

3

1

OUT

AUDIO / DASNET O UT

3

FI4030mA 4pol.

FI-Schalter

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

3

Matrix 9X9

3

2

OUT

OUT

1

PH.1 PH.2 PH.3

OUT

MAX.

16A/ OUT

I

DASNET-RACK-99

ON

2

1

3

3

PUSH

2

1

3

2

OUT

OUT

RESISTOR

ON

POWER

TERMINATION

2

3

1

2

1

2

1

2

1

2

1

AUDIO IN

2

1

2

1

2

1

2

1

FROM 1 x UX-221A L

FROM 3 x AERO-40A L FROM 3 x AERO-40A R

FROM 3 x AERO-40A L FROM 3 x AERO-40A R

FROM 1 x UX-221A L

FROM 1 x UX-221A L

1

OUT

3

3

3

2

OUT

OUT

3

3

1

OUT

AUDIO / DASNET OUT

3

FI4030mA 4pol.

FI-Schalter

PHASE 2: 18A

PHASE 3: 9A

I

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

3

Matrix 9X9

3

2

OUT

OUT

1

PH.1 PH.2 PH.3

OUT

MAX.

16A/ OUT

PHASE 1: 18A

DASNET-RACK-99

LOAD PER PHASE

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

13

x 1

243cm / 96”

228cm / 90”

251cm / 99”

USB-RS485 Converter

x 3

x 1

DSP-4080

12 AERO-40A

4 x aero40

4 x aero40

4 x aero40

4 x aero40

243cm / 96”

4 x aero40

4 x aero40

3 x UX-221A3 x UX-221A

4 x aero404 x aero40

3 x UX-221A3 x UX-221A

4 x aero40

4 x aero40

4 x aero40

4 x aero40

228cm / 90”251cm / 99”

4 x aero40

4 x aero40

4 x aero40

3 x UX-221A

3 x UX-221A

4 x aero40 4 x aero40

4 x aero40

x 10

A40 Accessories

Speaker cabling Dollies

14

Processors (included in the racks)

PL-40S metal transport dolly for 3 or 4 AERO-40A

x 8

x 8

eCPK_20 (CAT 7 ethernet cable + 3x2.5mm2, audio +data + power, 20m length)

eC_09 (CAT 7 ethernet cable; audio +data, 90cm length)

12 AERO-40A + 6 UX-221A

1

3

PUSH

2

2

1

2

1

2

1

2

1

2

1

AUDIO IN

2

1

2

1

2

1

2

1

Plink1_09 (power link 2.5mm2 90cm)

DASNET-RACK99

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

Euro Truck 6m Trailer

ON

2

3

1

RESISTOR

ON

POWER

TERMINATION

3

3

3

3

3

3

3

3

LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9

3

Matrix 9X9

AUDIO / DASNET OUT

American Truck 90” x 232”

American Truck 99” x 232”

x 2

x 3

x 2

x 2

3

2

OUT

OUT

1

OUT

3

2

OUT

OUT

1

OUT

FI4030mA4pol.

FI-Schalter

3

2

OUT

OUT

1

PH.1 PH.2 PH.3

OUT

MAX.

16A/ OUT

I

Covers

FUN-4-AE40 is a protective nylon cover for 4 AERO-40A

Rigging frames

FUN-3-UX221 nylon cover for a stack of 3 UX-221A

x 2

AX-AE40S3

Dollies

PL-221S

The PL-221S dolly is used to

transport stacks of 2 or 3 UX-221A.

ANNEX I : Schematics

_

_ _

_

_

_

L1 L3L2

N L2L1 L3 N L2L1 L3

_

_

_

RCD

40A/30mA

____

_ _ _

_ _

_

_ _

_ _ _

_ _ _

OUT (Looped)IN

PC 230V 16A

___

_

_

PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16APC 230V 16A

_

_

_

_

_

_

_

_

_

_

PH3.1 PH3.2 PH3.3PH2.3PH2.2PH2.1PH1.3PH1.2PH1.1AUX

DISTRO-RACKNET-32-9

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

_

_

_

_

_

15

1.0

16

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

ANNEX II : DASnet cables

It is very important to use the system with the intended cables to prevent electromagnetic
interferences between the analog audio signal, the DASnet data and the power. Be sure to
check the specifications provided by the cable manufacturer. It is also especially important
when installing connectors yourself, to note that when termination is not accurate, a cable
will be unable to achieve its maximum performance and could have interferences.

There are 4 different types of cables.

- The main feeds which include power and a STP, CAT7 cable. These cables are named
eCP_xx (xx refers to cable length).

- The links between cabinets (aero40A/Convert15A/LX-218CAnet), which are STP CAT7
cables. Cable code eC_09

- Power Links between cabinets.Cable code Plink1_09

- Links for RoadNet series. Power+STP CAT7. eCPk_1/eCPk_5

Important

The main feed cable eCP_xx has the following structure:

Jacket

STP CAT 7 cable with Aluminium
Shield for each individual pair

AL Shield

and a main aluminium Shield.
The main Shield has to be
soldered to the etherCon
housing.

The eC_09 cable is a CAT5e
cable with global Aluminium
Shield.

ecP_xx: Power cable 3x2.5mm + CAT7 4x (2 x 0.14mm )

The pin out of the EtherCon to XLR is the following on the eCP cables:

etherCon XLR

1 Orange-White Audio+ 2
2 Orange Audio- 3
3 Green-White Audio Earth 1
4 Blue
5 Blue-White
6 Green Data Earth 1
7 Brown-White Data- (A) 3
8 Brown Data+ (B) 2

Jacket

2 2

Manual del Usuario / DASNET-RACK99-230 / User’s Manual

17

www.dasaudio.com

UM_RACK991_01_EN

DAS Audio Group, S.L.

C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. [phone]

DAS Audio of America, INC.

6900 NW 52th Street
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1 888 DAS 4 USA

DAS Audio Asia PTE. LTD.

3 Temasek Avenue, Centennial
Tower #34-36
Singapore 039190
Tel. [phone]

DAS do Brasil LTDA.

Rua Dos Andradas, 382 SL
Santa Efigênia, São Paulo
Brasil. CEP: 01208-000
Tel. [phone]